- Clean vid/pid in Kconfig and add fastboot for rk3399
- add 'u-boot, spl-fifo-mode' for mmc
- Use FIT generator for rk3229 optee and rk3368 ATF
- fan53555: add support for Silergy SYR82X and SYR83X
The RK3368 lion board ATF can use bl31.elf like RK3399 and get the FIT
source with generic FIT generator script at:
arch/arm/mach-rockchip/make_fit_atf.py
And then we can use 'BL31' environment to get the path of bl31.elf
instead of copy it into U-Boot folder.
CC: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- In ARMv8 NXP Layerscape platforms we also need to make use of
CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
ENV_IS_IN_FLASH.
- Migrate all platforms.
Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We can only configure and set the environment in SPL when we have a
particular environment location set that is not "nowhere" like it is in
SECURE_BOOT designs. Update the code to reflect that.
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
These functions can only be built and used when we have
ENV_IS_IN_SPI_FLASH, use that as a guard.
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The board file has a build time check to ensure that we do not have the
redundant environment overwriting the factory data. However, using the
symbol CONFIG_ENV_SIZE_REDUND isn't strictly needed as that is always
the same as CONFIG_ENV_SIZE. Use CONFIG_ENV_SIZE instead so that we can
later drop CONFIG_ENV_SIZE_REDUND.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Support tinker-s board. The board is equivalent of tinker board
except of emmc.
TODO:
- support of usb current burst when the board is powered from pc
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROC-RK3308-CC is a rk3308 based board designed by
Firelfy, with eMMC and 256MB DDR3 and RTL8188 Wifi
on board.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rockpro64 needs to setup I/O domains in order for USB to work in u-boot.
Since we currently don't have a driver to do that, split it into its own
board file and initialize I/O domains here.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-rk3399-pc_defconfig is committed in below
commit <8a681f4c5aa15db51ad0209734859c9fe7c29cfd> ("rockchip: rk3399:
Add ROC-RK3399-PC support")
which doesn't follow the existing defconfigs on rk3399.
So, rename as followed with other rk3399 defconfigs.
Cc: Levin Du <djw@t-chip.com.cn>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The px30 evb is an evaluation board for the px30 together with a dsi-
connected display. This adds board and config files for it.
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rename the CONFIG_SECURE_BOOT name to CONFIG_NXP_ESBC to avoid
conflicts with UEFI secure boot.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
There is an option to enable the board detection for TI platforms.
If this is option is not set, there is no reason to set the EEPROM
bus address or chip address.
This patch makes both EEPROM_BUS_ADDRESS and EEPROM_CHIP_ADDRESS
depend on TI_I2C_BOARD_DETECT.
Signed-off-by: Adam Ford <aford173@gmail.com>
The PMIC enables power to the MMC card by default, but depending
on the state it was left when restarted, it's possible the MMC
may be powered down.
This patch patch explicitly tells the twl4030 to power the MMC.
Signed-off-by: Adam Ford <aford173@gmail.com>
This adds platform code and the device tree for the Phytium Durian Board.
The initial support comprises the UART and the PCIE.
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Steven Hao <liuhao@phytium.com.cn>
add DM PCI support on the socrates board.
use PCIE_FSL now.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
add socrates device tree from linux:
commit 71ae5fc87c34 ("Merge tag 'linux-kselftest-5.2-rc1' of
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest")
and added SPDX license identifier.
Did not fix checkpatch warnings:
arch/powerpc/dts/socrates.dts:235: check: Please don't use multiple blank lines
arch/powerpc/dts/socrates.dts:238: error: code indent should use tabs where possible
Also, add me as board maintainer.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
with u-boot,dm-spl added for imx8qm-pm node, and SPL_SIMPLE_BUS enabled,
the bind and probe code in board file could be removed.
Also we need to enlarge SYS_MALLOC_F_LEN to avoid calloc fail.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds support for the brppt2 board. The board is based on the
i.mx6 dual-lite SoC.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Enable bd71837 pmic for i.MX8MM EVK board, need to set voltage for
DRAM and linux suspend voltage requirement.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
We are going to add i2c pmic support before dram could be used.
So we need enable clk driver earlier, so use spl_early_init
and move clock controller probe eariler to board_init_f.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Migrate to DM_VIDEO, update the device tree and remove code that is no
longer necessary.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The mccmon6 has been used a "mixed" approach between SPL and
U-Boot proper sources.
This commit decoupes SPL and u-boot proper, which allows clear
distinction between those two code bases and facilitates
conversion to DM/DTS on this particular board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit converts mccmon6's u-boot proper (in a single commit to avoid
build breaks) to use solely DM/DTS.
The DTS description of the mccmon6 has been ported from Linux kernel
(v4.20, SHA1: 8fe28cb58bcb235034b64cbbb7550a8a43fd88be)
Signed-off-by: Lukasz Majewski <lukma@denx.de>
In order for 'bmode emmc' to work, the eMMC needs to be initialized in the
SPL. This change initializes the eMMC as BOOT_DEVICE_MMC1 (index=0).
Signed-off-by: Claudius Heine <ch@denx.de>
The board_boot_modes contained the wrong values for the emmc entry.
The eMMC here is connected over a 8-bit bus.
This change allows to use the 'bmode emmc' command to boot from emmc.
Signed-off-by: Claudius Heine <ch@denx.de>
Introduce imx6ull-colibri-u-boot.dtsi for u-boot specific properties to
keep original imx6ull-colibri.dts in sync with Linux.
Move all contents of imx6ull-colibri.dts to imx6ull-colibri.dtsi +
additionally fix checkpatch warnings.
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Back in the day on early board samples built-in Digilent JTAG probe
was not functional so we used externally attached Ashling Opella-XD
probe. But now with production units everything works as expected and
so we anybody may enjoy readily avaialble built-in JTAG probe so
we specify Digilent oprion on MDB's command line example.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
At present some boards generate kwbimage.cfg in the source tree
during the build. This breaks buildman testing on some systems
where the source tree is read-only. Update makefile rules to
generate it in the build tree instead.
Note some other boards have the kwbimage.cfg file written in
advance, hence we need check if the file exists in the build
tree first, otherwise we fall back to one in the source tree.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
