Move
arch/arm/cpu/arm926ejs/kirkwood/* -> arch/arm/mach-kirkwood/*
Note:
Perhaps, can we merge arch/arm/mach-kirkwood and
arch/arm/mvebu-common into arch/arm/mach-mvebu, like Linux?
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
In U-boot, the directory structure, arch/$(ARCH)/cpu/$(CPU)/$(SOC)/
has been adopted except that $(CPU) is missing from some
architectures and $(SOC) is missing from some CPUs.
This structure did not fit very well in some cases.
[1] AT91
AT91 SoC family have been developed across some ARM processor
generations. Generally speaking, some IPs are often re-used in the
same SoC family (same SoC vendor) even when the main processor is
updated. As a result, a SoC-common directory is needed in the upper
level. Currently, AT91 source files are placed as follows:
arch/arm/cpu/arm920t/at91/*
arch/arm/cpu/arm926ejs/at91/*
arch/arm/cpu/armv7/at91/*
arch/arm/cpu/at91-common/*
Once directories are split, the motivation for refactorings across
CPU directories is lost. Some files in arm920t/at91/ and
arm926ejs/at91/ are so similar that they could be merged.
[2] Tegra
Tegra is a little bit special case where different CPUs are used for
SPL and the main U-boot. To obey the arch/$(ARCH)/cpu/$(CPU)/$(SOC)
structure, the source files must be placed across the CPUs,
again SoC-common directory is necessary in the upper level.
Moreover, there are several families in Tegra: Tegra20, Tegra30,
Tegra114, Tegra124. Here again, the tegra-common directory is needed
to contain commonly-used files.
Tegra directories have been sprinkled in the directory structure.
arch/arm/cpu/arm720t/tegra20
arch/arm/cpu/arm720t/tegra30
arch/arm/cpu/arm720t/tegra114
arch/arm/cpu/arm720t/tegra124
arch/arm/cpu/arm720t/tegra-common
arch/arm/cpu/armv7/tegra20
arch/arm/cpu/armv7/tegra30
arch/arm/cpu/armv7/tegra114
arch/arm/cpu/armv7/tegra124
arch/arm/cpu/armv7/tegra-common
arch/arm/cpu/tegra20-common
arch/arm/cpu/tegra30-common
arch/arm/cpu/tegra114-common
arch/arm/cpu/tegra124-common
arch/arm/cpu/tegra-common
As you see, splitting SoC code by the CPU is not going well,
especially for ARM.
Why don't we collect SoC-specific files into a single place?
A good example we can follow is Linux's arch/arm/mach-* structure.
This item was discussed in the following thread:
http://thread.gmane.org/gmane.comp.boot-loaders.u-boot/188548/
Looks like I got some positive responses and we are almost ready to
start this movement.
This commit prepares arch/arm/Makefile for describing machdirs in it.
After this commit, we can move SoC directory to arch/arm/mach-$(SOC)
in simple steps although some cases such as AT91 and Tegra need more
fixes.
What we generally have to do is:
[1] Move files arch/arm/cpu/$(CPU)/$(SOC)/* to arch/arm/mach-$(SOC)/*
[2] Add machine entry into arch/arm/Makefile
[3] Remove "obj-y += $(SOC)" from arch/arm/cpu/$(CPU)/Makefile
[4] Fix the Kconfig file path in arch/arm/Kconfig
[5] Modify MAINTAINERS if necessary
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The board select menu in arch/arm/Kconfig is still big.
To slim down it, this commit moves AT91 boards to
arch/arm/mach-at91/Kconfig.
Also, consolidate "config SYS_SOC" in each board Kconfig.
The Kconfig files under board/ directory were modified with the
following command:
find board -name Kconfig | xargs sed -i -e '
/config SYS_SOC/ {
N
/default "at91"/ {
N
d
}
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.co>
Introduce arch_reserve_stacks() to tailor gd->start_addr_sp and gd->irq_sp to
the architecture needs.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The self-bias circuit is used by the bandgap during startup.
Once the bandgap has stabilized, the self-bias circuit should
be disabled for best noise performance of analog blocks.
Also this bit should be disabled before the chip enters STOP mode or
when ever the regular bandgap is disabled.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@freescale.com>
The only LPC3250 board works fine with enabled generic board support,
add CONFIG_SYS_GENERIC_BOARD right into the arch config header.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
So that the CONFIG_SPL_FEL option is not needed anymore. And the regular
SPL binary, generated by the default u-boot build, is now also bootable
over USB in the FEL mode. The SPL still can boot from the SD card too.
A bunch of system registers need to be saved/restored in order to ensure
that the IRQ handler still works in the BROM FEL code after getting
control back from the SPL. This is done in the sunxi code instead of
abusing ifdefs in 'start.S'.
The decision whether to load the main u-boot binary from the SD card or
return to the FEL code in the BROM is done at runtime.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
[hdegoede@redhat.com: Since we now restore various regs before returning to
the FEL BROM code we can drop the sunxi specific #ifdefs in start.S]
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Make sunxi's FEL code fit with the normal U-Boot boot sequence instead of
creating its own. There are some #ifdefs required in start.S. Future work
will hopefully remove these.
This series is available at u-boot-dm, branch sunxi-working.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Some boards have a special way of loading U-Boot that does not fit with
the existing SPL code. For example sunxi uses an 'FEL' mode where U-Boot
is loaded over USB. Add a CONFIG option and boot mode for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The link register value can be required on some boards (e.g. FEL mode on
sunxi) so use a branch instruction to jump to save_boot_params() instead
of a branch link.
This requires a branch back to save_boot_params_ret so adjust the users
to deal with this. For exynos just drop the function since it doesn't
do anything.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Move the dram helper functions to a separate C file, rather then having them
as inline helpers in dram.h. This saves 144 bytes in the .text segment for
sun6i builds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
KS2 ddr3 initialization uses ddr3_size global variable before u-boot
relocation. Even if the variable is not being used after relocation,
writing to it corrupts relocation table.
This patch removes the global ddr3_size variable and uses local one
instead.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
When EMAC is in the boot order, the boot ROM sets OPP50 and the
MAC clock is set to /2. SPL needs to change it to /5 for Ethernet
to generate the correct txclk. This patch sets it correctly.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
The value in SDRAM_REF_CTRL controls the delay time between
the initial rising edge of DDR_RESETn to rising edge of DDR_CKE
(JEDEC specs this as 500us). In order to achieve this, SDRAM_REF_CTRL
should be written with a value corresponding to 500us delay before
starting DDR initialization sequence, and configure proper
value at the end of sequence.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
DDR3 timing and latency paramenters were not configured
correctly for 666MHz. Fixing the timing and latency values
according to Data sheet.
This fixes the random crashes seen on DRA72-evm.
Signed-off-by: Angela Stegmaier <angelabaker@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Since we have src, div and pre-div mask bits defined corresponding
to peripherals, calculation of clock specific to I2C appears
redundant and confusing. Using clk_bit_info struct we can write
calculations generic to all peripherals which makes code easy to
understand and free from peripheral specific exceptions.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We have assumed and kept mask bits for divider and pre-divider
as 0xf and 0xff, respectively. But these mask bits change from
one peripheral to another, and hence, need to be specified in
accordance with the peripherals.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Replacing SoC and peripheral specific function calls with generic
clock_get_periph_rate calls to get the peripheral clocks.
Also, removing dead code of peripheral and SoC specific function
implementations which was used earlier for fetching peripheral clocks.
This code is not being used anymore because of the introduction
of generic clock_get_periph_rate function.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
exynos5_get_periph_rate function reads incorrect div for
SDMMC2 & 3. It also reads prediv and does division only for
SDMMC0 & 2 when actually various other peripherals need that.
Adding changes to fix these mistakes in periph rate calculation.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We planned to fetch peripheral rate through one generic API per
peripheral. These generic peripheral functions are in turn
expected to fetch apt values from a function refactored as
per SoC versions. This patch adds support for fetching peripheral
rates for Exynos5420 and Exynos5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Moving exynos5420_get_pll_clk function definition up in the
code to keep it together with rest of SoC_get_pll_clk functions.
This makes code more legible and also removes the need of
declaration when called before the position of definition in
code. Also, renaming exynos5420_get_pll_clk to
exynos542x_get_pll_clk because it is being used for both Exynos
5420 and 5800.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Apparently, members of clk_bit_info array do not map correctly
to the members of enum periph_id. This mapping got broken after
we changed periph_id(s) to reflect interrupt number instead of
their position in a sequence. This patch intends to fix above
mentioned issue.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exynos5420 has different registers with other exynos5 SoCs to control
usb device phy, so need separated function to enable exynos5420 usb
device phy.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This needs for special handling of nRESET_OUT line(GPD1-0 gpio) for eMMC
memory to perform complete reboot on Odroid XU3 board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This needs for special handling of nRESET_OUT line(GPK1-2 gpio) for eMMC
memory to perform complete reboot on Odroid X2/U3 boards.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The most exynos used the "Ratio + 1" as div value.
And value at register is "Ratio".
So if want to set exact value, it needs to subtract one.
Value at register ("Ratio") = div - 1
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
r8a7794 uses ARM SoC of CA7 base. If we want to use dcache on CA7, we
need to enable SMP bit of Auxiliary Control Register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
SILK is an entry level development board based on R-Car E2 SoC (R8A7794)
This commit supports the following peripherals:
- SCIF, I2C, Ethernet, QSPI, MMC, USB Host
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With driver model the number of PIO ports is defined by platform data, so
remove it from the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
When booting in JTAG mode, there is no way to use soft break-points, and
no way of knowing when SPL has finished executing (so the user can issue
a 'halt' command to load u-boot.bin for example)
Add a debug output and simple loop to stop execution at the completion of
the SPL initialisation as a pseudo break-point when booting in JTAG mode
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Section 4.1.2 of Freescale Application Note AN4199 describes the
configuration required to operate the mx28 from a 5V source without a
battery.
This patch changes the behaviour of the dropout control of the DC-DC
converter (refer to section 11.12.9 of the mx28 Application Processor
Reference Manual - Document Number: MCIMX28RM, Rev 2, 08/2013) to the
following:
- Always use 4P2 Linear Regulator if CONFIG_SYS_MXS_VDD5V_ONLY is defined
- Switch between 4P2 Linear Regulator and Battery, using whichever has
the highest voltage if CONFIG_SYS_MXS_VDD5V_ONLY isnot set (this is
the same as the pre-patch behaviour)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Signed-off-by: Damien Gotfroi <dgotfroi@greenwatch.be>
It is difficult to track down fail to boot issues in the mxs SPL.
Implement the following to make it easier:
- Add debug outputs to allow tracing of SPL progress in order to track
where failure to boot occurs. DEUBUG and CONFIG_SPL_SERIAL_SUPPORT must
be defined to enable debug output in SPL
- Add TODO comments where it is not clear if the code is doing what it
is meant to be doing, even tough the board boots properly (these comments
refer to existing code, not to any code added by this patch)
Signed-off-by: Graeme Russ <gruss@tss-engineering.com>
Should use AIPS3 configuration address 0x0227C000 to set AIPS3,
not the AIPS3 base address.
Additional, replace AIPS1_BASE_ADDR to AIPS3_ARB_BASE_ADDR to align with
AIPS1 and AIPS2, and resolve the AIPS3_ARB_BASE_ADDR undefine problem.
Signed-off-by: Ye.Li <B37916@freescale.com>
As the at91cap9adk board is removed by commit: b5508344
(ARM: remove broken "at91cap9adk" board), so the at91cap9
code is not used anymore, and also the document for
at91cap9 can not be found on www.atmel.com, so remove the
at91cap9 related code.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
Some SoC need to redirect the saic to aic to make the interrupt to
work, here add a weak function to be replaced by real function.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
The SFR (special function registers) can be shared bwteen
sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adoptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This matrix header file can be shared between sama5d3 and sama5d4 soc.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
[whitespace adaptions for 80 char compliance]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the Marvell Armada-XP. With this addition
the bin_hdr integration is not needed any more. The SPL will first
initialize the serdes/PHY and the call the DDR setup and training code
now integrated into mainline U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the db-mv784mp-gp eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
This patch adds SPL support to the maxbcm MV78460 based board. Including
the fixed DDR configuratrion needed for the DDR training code. And the
the serdes PHY init code.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Luka Perkov <luka.perkov@sartura.hr>
Checking if the pointer is NULL would be easier to know the tail
of the boot_device_table[] array.
For clarification, add the /* sentinel */ comment.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The return value of get_boot_mode_sel() is used as the index of
the boot_device_table[] array. Its type should be "int" rather
than "u32".
Use only the iterator "i" for the loop in do_pinmon().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To use I2C controllers on PH1-sLD8, the bit 10 (SCL0/SDA0)
and bit 11 (SCL1/SDA1) of IECTRL register must be set.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
It is true that unused functions are removed from the ELF image
by the compiler's garbage collection but relying on it too much
does not look nice.
Currently, the build is taking more than it should.
Refactor the makefiles to compile only files that are really needed.
CONFIG_SOC_INIT and CONFIG_DRAM_INIT are no longer needed by the
optimization.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), checkboard() is invoked only when
show_board_info() fails to get the model name from Device Tree.
It never happens because UniPhier SoCs now only work with
CONFIG_OF_CONTROL and all the root nodes of UniPhier device trees
have the "model" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Since commit 0365ffcc0b (generic-board: show model name in
board_init_f() too), the support card information has not been
displayed because check_support_card() is invoked only when
show_board_info() fails to get the model name from Device Tree.
This commit adds misc_init_f() function to call check_support_card()
from there.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Now init functions called from board_postclk_init() and dram_init()
are only necessary for SPL.
Move them to spl_board_init() for clean-up.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Currently, I/O pin settings are not necessary for SPL.
The board_early_init_f() seems a suitable place to call pin_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The EEPROM chips on UniPhier reference daughter boards expect 2-byte
offset address.
Since 7132b9fd68 (dm: i2c: dts: Support an offset-len device tree
property), I2C sub-nodes can have "u-boot,i2c-offset-len" property.
It is convenient to set the default I2C offset address length in
Device Tree, so that we do not have to set it on the command line.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This EEPROM chip is installed on the expansion board commonly used
on UniPhier platform. To avoid duplicated description, move the
EEPROM node to a separate file and include it from other device tree
sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This dummy header was introduced by commit 630bf80ebb (ARM:
UniPhier: add dummy gpio.h to enable CONFIG_OF_CONTROL).
Thanks to commit a08d643dbd (dm: Drop gpio.h header from
fdtdec.c), such an ugly workaround is no longer needed.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If we don't know the relocation address, the raw values are not very useful.
Show the pre-relocation values as well as these can be looked up in
System.map, etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
It turns out that the device_mode_data is rsb specific, rather then slave
specific, so integrate the rsb_set_device_mode() call into rsb_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
And use this to set the GMAC Transmit Clock Delay Chain value on Banana
boards, rather then keying of CONFIG_TARGET_FOO.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch adds basic constructs in the ARMv8 u-boot code
to handle and apply Cortex-A57 specific erratas.
As and example, the framework showcases how erratas 833069, 826974
and 828024 can be handled and applied.
Later on this framework can be extended to include other
erratas.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
The Juno Development Platform is a physical Versatile Express
device with some differences from the emulated semihosting
models. The main difference is that the system is split in
a SoC and an FPGA where the SoC hosts the serial ports at
totally different adresses.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Versatile Express ARMv8 semihosted FVP platform is still
using the legacy CONFIG_SYS_EXTRA_OPTIONS method to configure
some compile-time flags. Get rid of this and create a Kconfig
entry for the FVP model, and a selectable bool for the
semihosting library.
The FVP subboard is now modeled as a target choice so we can
eventually choose between different ARMv8 versatile express
boards (FVP, base model, Juno...) this way. All dependent
symbols are updated to reflect this.
The 64bit Versatile Express board symbols are renamed
VEXPRESS64 so we have some chance to see what is actually
going on. Tested on the FVP fast model.
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This change fixes i2c bus numbering for Odroid U3.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Some versions of Exynos5 supports High-Speed I2C,
on few interfaces, this change allows support this.
The new flag is: PINMUX_FLAG_HS_MODE
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Without this alias setting, the seq numbers
of the i2c devices are wrong.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
This patch modify i2c nodes in exynos4.dtsi with:
- adding proper interrupts arrays for each i2c node,
which allows to decode periph id
- add reg address for each i2c node for i2c driver internal use
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Rather than assuming that the chip offset length is 1, allow it to be
provided. This allows chips that don't use the default offset length to
be used (at present they are only supported by the command line 'i2c'
command which sets the offset length explicitly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
U-Boot now supports using GPIOs using bank phandles instead of global
numbers. Update the exynos device tree files to use this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Minkyu Kang <mk7.kang@samsung.com>
In f0c3a6c we stopped setting gd in board_init_f, but later had to
revert to due problems on certain platforms. As davinci does not look
to have these problems, we can drop the setting here and rely upon
crt0.S to do it.
Cc: Peter Howard <pjh@northern-ridge.com.au>
Signed-off-by: Tom Rini <trini@ti.com>
On the DRA72x (J6Eco) EVM one PMIC SMPS is powering three SoC
core rails. This concept of using one SMPS to supply multiple
core domains (in various, although limited combinations, per
primary device use case) has now become common and is used by
many customer J6/J6Eco designs; it is supported by a number of
corresponding PMIC OTP versions.
This patch implements correct operation of the core voltages
scaling routine by ensuring that each SMPS that is supplying
more than one domain shall be written only once, and with the
highest voltage of those fused in the SoC (or of those defined
in the corresponding header if fuse read is disabled or fails)
for the power rails belonging to the group.
The patch also replaces some PMIC-related magic numbers with
the appropriate definitions. The default OPP_NOM voltages for
the DRA7xx SoCs are updated as well, per the latest DMs.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Set only the 0-3 bits of the FPGA_RST_CTRL register
as other bits should not be set to 1.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Setup half of memory from ram_size for ECC case.
All the time the same board can be configured
with or without ECC. Based on ECC case detection
use half of memory with the same configuration.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added the lowlevel_init to enable the Neon instructions.
Initially the u-boot was causing undefined instruction
exception if loaded through tcl, and working fine if loaded
through FSBL. The exception was causing in convertion formula
of given time to ticks. It was because, the Neon instructions
were disabled and hence causing the undefined exception. In
FSBL case, the FSBL was enabling the Neon instructions. Hence,
added the lowlevel_init to enable the Neon instructions.
Also enable neon instructions for non-xilinx toolchain.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Acked-by: Radhey Shyam Pandey <radheys@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
As QSPI/DSPI and IFC are pin multiplexed, QSPI and DSPI are
only enabled in QSPI boot, and disabled in other boot modes.
IFC is enabled in NOR/NAND/SD boot, and disabled in QSPI boot.
This patch will add fdt support for the above rules.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Defining variable gic_dist_addr as a globe one prevents some
functions, which use it, from being used before relocation
which is the case in the deep sleep resume process on Freescale
SoC platforms.
Besides, we can always get the GIC base address by calling
get_gicd_base_address() without referring gic_dist_addr.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Era property is added in the crypto node in device tree.
Move the code to do so from arch/powerpc/mpc8xxx/fdt.c to
drivers/sec/sec.c so that it can be used across arm and
powerpc platforms having crypto node.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
[York Sun: Fix commit message indentation]
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they
do not support GPIO.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.This commit adds a dummy <asm/arch/gpio.h>
to support OF_CONTROL for LS102x platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Internal memory controller counters can reach a bad state after
training in DDR4 mode if accumulated ECC or DBI mode is eanbled.
Signed-off-by: York Sun <yorksun@freescale.com>
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by <linux/sizes.h> for readability.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For PH1-Pro4, the bit 6 of the IECTRL must be set. It is the only
available bit in this register. There is no effect of the write
access to the other bits.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The assembly directive ".rept ... .endr" allows us to write the
init_page_table much shorter. To make things further simpler,
set the text and stack area as Normal Memory, and the other sections
as Device attribute.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The DDR PHY training function, ddrphy_prepare_training() would not
work if compiled with GCC 4.9.
The struct ddrphy (arch/arm/include/asm/arch-uniphier/ddrphy-regs.h)
is specified with __packed because it represents a hardware register
mapping, but it turned out to cause a problem on GCC 4.9.
If -mno-unaligned-access is specified (yes, it is in
arch/arm/cpu/armv7/config.mk), GCC 4.9 is aware of the
__attribute__((packed)) and generates extra instructions to perform
the memory access in a way that does not cause unaligned access.
(Actually it is not need here because the register base, the first
argument of the ddrphy_prepare_training(), is always given with a
4-byte aligned address.)
Anyway, as a result, readl() / writel() is divided into byte-wise
accesses. The problem is that this hardware only accepts 4-byte
register access. Byte-wise accesses lead to unexpected behavior.
There are some options to avoid this problem.
[1] Remove -mno-unaligned-access
[2] Add __aligned(4) along with __packed to struct ddrphy
[3] Remove __packed from struct ddrphy
[1] solves the problem for ARMv7, but it does not for pre-ARMv6 and
ARMv6-M architectures where -mno-unaligned-access is default.
So, [1] does not seem reasonable in terms of code portability.
Both [2] and [3] work well, but [2] seems too much. All the members
of struct ddrphy have the u32 type. No padding would be inserted
even if __packed is dropped.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Tom Rini <trini@ti.com>
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the frontend does have deep enough fifo-s.
As added advantage of this is that it results in much better memory bandwidth
as it reduces the amount of dram bank switches, for more details see:
http://ssvb.github.io/2014/11/11/revisiting-fullhd-x11-desktop-performance-of-the-allwinner-a10.html
Note that this changes the pipeline searched for in the simplefb node, we can
get away with doing this now, since no kernel has yet shipped with simplefb
dtb nodes, and I will make sure to get a simplefb node with the new pipeline
into 3.19 before it ships.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The clocks on the A80 are hooked up slightly different, add support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add initial sun9i (A80) clock setup support, enough to get the uart + mmc
going.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a headerfile with all the base addresses from the sun9i blocks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun4i - sun8i have (aprox.) the same iomem layout, but sun9i is quite
different, so add a wrapper cpu.h which includes the right mach specific
cpu_sun#i.h based on mach, like we already do with clock.h and dram.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Which pll-s are available depends on the machine type, move the
clock_get_pllX / clock_set_pllX prototypes to the clock_sun?i.h header files
so that we only declare what is actually available. e.g. clock_get_pll5p()
is not available on sun6i / sun8i, and with sun9i we get a completely
different set of plls.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
As the comment says now that we have SPL support this is no longer necessary,
as PLL6 is already setup with the exact same parameters by the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Define two structure mx6sx_iomux_ddr_regs and mx6sx_iomux_grp_regs.
Add a new function mx6sx_dram_iocfg to configure dram io.
Since mx6sx only have one channel mmdc0, define a new empty macro MMDC1
to replace mmdc1->entry=value for mx6sx. And to other mx6 soc, MMDC1
effects as "mmdc1->entry=value".
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
2 recent sunxi changes have removed the usage of lowlevel_init by moving some
code around and then setting CONFIG_SKIP_LOWLEVEL_INIT.
This is problematic for 2 reasons:
1) It does not just stop s_init from being called, it also stops
cpu_init_cp15 from getting called, which is undesirable.
2) We want u-boot.bin to be usable standalone, without SPL, some people e.g.
use an upstream u-boot.bin together with Allwinner's boot0 loader. So
u-boot.bin must (re)initialize the gpios, timer, etc.
This commit restores the lowlevel_init / s_init usage, while keeping the
changes to no longer use the global-data (gd) struct in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
in thumb mode compiler says for example for arch/arm/lib/cache-cp15.c
when enabling CONFIG_SYS_THUMB_BUILD:
{standard input}: Assembler messages:
{standard input}:373: Error: selected processor does not support Thumb mode `mrc p15,0,r4,c1,c0,0'
{standard input}:416: Error: selected processor does not support Thumb mode `mcr p15,0,r3,c2,c0,0'
so, if caches are disabled, do not use this command on arm926ejs.
used on at91 in SPL, to reduce size of SPL.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the new Barco platinum platform. It currently
includes those two boards:
platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.
platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.
The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to get rid of this SPL-specific setting of the global_data pointer.
It is already set up in start.S immediately before board_init_f() is called,
and there may be information there that is needed (e.g. pre-reloc malloc
info).
Signed-off-by: Simon Glass <sjg@chromium.org>
Prior to this change we set the gd pointer early so that we can store
data in it. This becomes problematic for DM changes as well as being
odd in general. Re-work the code paths so that we don't need to set the
gd pointer so early and instead can rely upon the normal setting of it.
In order to do this we do need to move certain calls from s_init into
spl_board_init(), mainly preloader_console_init and
save_omap_boot_params.
Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM,
OMAP5 uEVM, DRA7xx EVM
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move a few mux defines around so that all the mux defines are properly sorted
by port number.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.
With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.
With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.
*) "unknown" is the actual name of this register in the android kernel sources
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.
Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.
A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.
This commit fixes this by filling the memory with a unique, distinct pattern.
The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.
While at it move mctl_mem_matches to dram.h for re-use in sun8i too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
