Linux modified the MTD driver interface in commit edbc4540 (with the
same name as this commit). The effect is that calls to mtd_read will
not return -EUCLEAN if the number of ECC-corrected bit errors is below
a certain threshold, which defaults to the strength of the ECC. This
allows -EUCLEAN to stop indicating "some bits were corrected" and begin
indicating "a large number of bits were corrected, the data held in
this region of flash may be lost soon". UBI makes use of this and when
-EUCLEAN is returned from mtd_read it will move data to another block
of flash. Without adopting this interface change UBI on U-boot attempts
to move data between blocks every time a single bit is corrected using
the ECC, which is a very common occurance on some devices.
For some devices where bit errors are common enough, UBI can get stuck
constantly moving data around because each block it attempts to use has
a single bit error. This condition is hit when wear_leveling_worker
attempts to move data from one PEB to another in response to an
-EUCLEAN/UBI_IO_BITFLIPS error. When this happens ubi_eba_copy_leb is
called to perform the data copy, and after the data is written it is
read back to check its validity. If that read returns UBI_IO_BITFLIPS
(in response to an MTD -EUCLEAN) then ubi_eba_copy_leb returns 1 to
wear_leveling worker, which then proceeds to schedule the destination
PEB for erasure. This leads to erase_worker running on the PEB, and
following a successful erase wear_leveling_worker is called which
begins this whole cycle all over again. The end result is that (without
UBI debug output enabled) the boot appears to simply hang whilst in
reality U-boot busily works away at destroying a block of the NAND
flash. Debug output from this situation:
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 1027
UBI DBG: ubi_io_read: read 4096 bytes from PEB 1027:4096
UBI DBG: ubi_eba_copy_leb: copy LEB 0:0, PEB 1027 to PEB 4083
UBI DBG: ubi_eba_copy_leb: read 1040384 bytes of data
UBI DBG: ubi_io_read: read 1040384 bytes from PEB 1027:8192
UBI: fixable bit-flip detected at PEB 1027
UBI DBG: ubi_io_write_vid_hdr: write VID header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:4096
UBI DBG: ubi_io_read_vid_hdr: read VID header from PEB 4083
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:4096
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:8192
UBI DBG: ubi_io_read: read 4096 bytes from PEB 4083:8192
UBI: fixable bit-flip detected at PEB 4083
UBI DBG: schedule_erase: schedule erasure of PEB 4083, EC 55, torture 0
UBI DBG: erase_worker: erase PEB 4083 EC 55
UBI DBG: sync_erase: erase PEB 4083, old EC 55
UBI DBG: do_sync_erase: erase PEB 4083
UBI DBG: sync_erase: erased PEB 4083, new EC 56
UBI DBG: ubi_io_write_ec_hdr: write EC header to PEB 4083
UBI DBG: ubi_io_write: write 4096 bytes to PEB 4083:0
UBI DBG: ensure_wear_leveling: schedule scrubbing
UBI DBG: wear_leveling_worker: scrub PEB 1027 to PEB 4083
...
This patch adopts the interface change as in Linux commit edbc4540 in
order to avoid such situations. Given that none of the drivers under
drivers/mtd return -EUCLEAN, this should only affect those using
software ECC. I have tested that it works on a board which is
currently out of tree, but which I hope to be able to begin
upstreaming soon.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Stefan Roese <sr@denx.de>
There is no page_size for ramtron flashes,
so just print the detected flash and it's size.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Qspi controller can have a memory mapped port which can be used for
data read. Added support to enable memory mapped port read.
This patch enables the following:
- It enables exchange of memory map address between mtd and qspi
through the introduction of "memory_map" flag.
- Add support to communicate to the driver that memory mapped
transfer is to be started through introduction of new flags like
"SPI_XFER_MEM_MAP" and "SPI_XFER_MEM_MAP_END".
This will enable the spi controller to do memory mapped configurations
if required.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Use flash->page_size arg in print_size() instead of
flash->sector_size while printing detected flas part details.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Now the common probing is handled in spi_flash_probe.c
hence removed the unneeded flash drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Compared to other spi flashes, ramtron has a different
probing and implementation on flash ops, hence moved
ramtron probe code into ramtron driver.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
From Micron, 512MB onwards, flash requires to poll flag status
instead of read status- hence added E_FSR flag on spectific
flash parts.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
SECT_4K, SECT_32K and SECT_64K opeartions are performed to
to specific flash by adding a SECT* flag on respective
spi_flash_params.flag param.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Few of the flashes(Atmel, Macronix and SST) require to
clear BP# bits in flash power ups.
So clear these BP# bits at probe time, so-that the flash
is ready for user operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Most of the SST flashes needs to write up using SST_WP, AAI
Word Program, so added a flag param on spi_flash_params table.
SST flashes, which supports SST_WP need to use a WP write
sst_write_wp instead of common flash write.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added AT45DB* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added SST25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Added S25FL* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added W25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added MX25L* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added GD25* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added EN25Q* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added M25P* parts are which are avilable in spi_flash_probe_legacy.c.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Added new spi_flash_probe support, currently added N25Q*
flash part attributes support.
Updated the sector_size attributes as per the flash parts.
Looks fine for with this sector_size for computing the size
of flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Divided the spi_flash framework into mutiple parts for
- spi_flash.c:
spi flash core file, interaction for spi/qspi driver to
spi_flash framework.
- spi_flash_ops.c
spi flash preffered operations, erase,write and read.
- spi_flash_probe.c
spi flash probing, easy to extend probing functionality.
This change will support to extend the functionality in a
proper manner.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
On a board with an i.mx28 and a Micron MT29F4G08ABAEAH4, Linux says:
NAND device: Manufacturer ID: 0x2c, Chip ID: 0xdc (Micron MT29F4G08ABAEAH4),
512MiB, page size: 4096, OOB size: 224) the ECC strength is 16.
root@(none):/sys/devices/virtual/mtd/mtd0# for i in ecc_strength oobsize subpagesize; do echo $i = `cat $i`; done
ecc_strength = 16
oobsize = 224
subpagesize = 4096
The ECC strength was not properly discovered by U-Boot causing the data
written by Linux to return an -74 (EBADMSG) when read from U-Boot. This
patch fixes mxs_nand_get_ecc_strength() to function in case of a NAND
flash with page_data_size = 4096 and page_oob_size= 224.
Signed-off-by: Elie De Brauwer <eliedebrauwer@gmail.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The PMECC use BCH algorithm to correct error. In BCH algorithm, the
primitive polynomial value is GF(2^13) for 512-bytes sector size. And it is
GF(2^14) for 1024-bytes sector size.
This patch will choose correct degree of the remainders (13 or 14) for
different sector size.
Tested in AT91SAM9X5-EK with MLC nand flash.
More detail can be refered to section 5.4.1 of:
AT91SAM ARM-based Embedded MPU Application Note
<http://www.atmel.com/Images/doc11127.pdf>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
1. if CONFIG_SYS_NAND_ONFI_DETECTION is defined, driver will check NAND flash's
ecc minimum requirement in ONFI parameter.
a) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are defined. then use it.
Driver will display a WARNING if the values are different from ONFI
parameters.
b) if CONFIG_PMECC_CAP, CONFIG_PMECC_SECTOR_SIZE are not defined, then use
the value from ONFI parameters.
* If ONFI ECC parameters are in ONFI extended parameter page, since we
are not support it, so assume the minimum ecc requirement is 2 bits
in 512 bytes.
* For non-ONFI support nand flash, also assume the minimum ecc
requirement is 2 bits in 512 bytes.
2. if CONFIG_SYS_NAND_ONFI_DETECTION is not defined, just use CONFIG_PMECC_CAP
and CONFIG_PMECC_SECTOR_SIZE.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
In this way, the pmecc corraction capbility can change in run time.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Define the galois index table offset in chip head file. So user do not need
to set by himself. Driver will set it correctly according to sector_size.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
[rebased on master]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch cleans up license header in these files:
board/freescale/p1022ds/spl.c
drivers/mmc/fsl_esdhc_spl.c
drivers/mtd/spi/fsl_espi_spl.c
Signed-off-by: York Sun <yorksun@freescale.com>
TPL is introduced in the patch "NAND: TPL : introduce the TPL
based on the SPL", here enable TPL for p1022ds nand boot.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
This patch introduces SPL to enable a loader stub that being loaded by
the code from the internal on-chip ROM. It loads the final uboot image
into DDR, then jump to it to begin execution.
The SPL's size is sizeable, the maximum size must not exceed the size of L2
SRAM. It initializes the DDR through SPD code, and copys final uboot image
to DDR. So there are two stage uboot images:
* spl_boot, 96KB size. The env variables are copied to L2 SRAM, so that
ddr spd code can get the interleaving mode setting in env. It loads
final uboot image from offset 96KB.
* final uboot image, size is variable depends on the functions enabled.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Add support for SST25WF080 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
- line over 80 characters
- foo * bar -> foo *bar
- removed unnecessary for single statement blocks.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
While the flash_detect_legacy() of drivers/mtd/cfi_flash.c
feed unmap_physmem() with MAP_NOCACHE as 2nd parameter,
the do_spi_flash_read_write() of common/cmd_sf.c
feed unmap_physmem() with the length of the mapped buffer
as 2nd parameter.
It's apparently a bug, and I personally think the 2nd parameter
should be the length of the mapped buffer.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The driver triggered a BUG() in nand_base.c:3214/nand_scan_tail()
because the ecc.strength was not set in NAND_ECC_HW_SYNDROME ECC
mode.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Newer gcc versions warn about unused variables. This patch corrects a few of
those warnings that popped up in a build for the palmtreo680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
before writing the received buffer to nand, erase the nand
sectors. If not doing this, nand write fails. See for
more info here:
http://lists.denx.de/pipermail/u-boot/2013-June/156361.html
Using the nand erase option "spread", maybe overwrite
blocks on, for example another mtd partition, if the
erasing range contains bad blocks.
So a limit option is added to nand_erase_opts()
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Move common flash write code into spi_flash_write_common().
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
Flag status register polling is required for micron 512Mb flash
devices onwards, for performing erase/program operations.
Like polling for WIP(Write-In-Progress) bit in read status register,
spi_flash_cmd_wait_ready will poll for PEC(Program-Erase-Control)
bit in flag status register.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no other call other than spi_flash_cmd_wait_ready(),
hence removed spi_flash_cmd_poll_bit and use the poll status code
spi_flash_cmd_wait_ready() itself.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the existing spi_flash_addr() for 3-byte addressing
cmd filling in write call.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Defined bank addr code on CONFIG_SPI_FLASH_BAR macro, to reduce the
size for existing boards which has < 16Mbytes SPI flashes.
It's upto user which has provision to use the bank addr code for
flashes which has > 16Mbytes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch updated the spi_flash read func to support all
sizes of flashes using bank reg addr facility.
The same support has been added in below patch for erase/write
spi_flash functions:
"sf: Support all sizes of flashes using bank addr reg facility"
(sha1: c956f600cbb0943d0afe1004cdb503f4fcd8f415)
With these new updates on sf framework, the flashes which has < 16MB
are not effected as per as performance is concern and but the
u-boot.bin size incrased ~460 bytes.
sf update(for first 16MBytes), Changes before:
U-Boot> sf update 0x1000000 0x0 0x1000000
- N25Q256
16777216 bytes written, 0 bytes skipped in 199.72s, speed 86480 B/s
- W25Q128BV
16777216 bytes written, 0 bytes skipped in 351.739s, speed 48913 B/s
- S25FL256S_64K
16777216 bytes written, 0 bytes skipped in 65.659s, speed 262144 B/s
sf update(for first 16MBytes), Changes before:
U-Boot> sf update 0x1000000 0x0 0x1000000
- N25Q256
16777216 bytes written, 0 bytes skipped in 198.953s, speed 86480 B/s
- W25Q128BV
16777216 bytes written, 0 bytes skipped in 350.90s, speed 49200 B/s
- S25FL256S_64K
16777216 bytes written, 0 bytes skipped in 66.521s, speed 262144 B/s
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Updated the spi_flash framework to handle all sizes of flashes
using bank/extd addr reg facility
The current implementation in spi_flash supports 3-byte address mode
due to this up to 16Mbytes amount of flash is able to access for those
flashes which has an actual size of > 16MB.
As most of the flashes introduces a bank/extd address registers
for accessing the flashes in 16Mbytes of banks if the flash size
is > 16Mbytes, this new scheme will add the bank selection feature
for performing write/erase operations on all flashes.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Read the flash bank addr register to get the state of bank in
a perticular flash. and also bank write happens only when there is
a change in bank selection from user.
bank read only valid for flashes which has > 16Mbytes those are
opearted in 3-byte addr mode, each bank occupies 16Mytes.
Suppose if the flash has 64Mbytes size consists of 4 banks like
bank0, bank1, bank2 and bank3.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Bank/Extended addr commands are specific to particular
flash vendor so discover them based on the idocode0.
Assign the discovered bank commands to spi_flash members
so-that the bank read/write will use their specific operations.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch provides support to program a flash bank address
register.
extended/bank address register contains an information to access
the 4th byte addressing in 3-byte address mode.
reff' the spec for more details about bank addr register
in Page-63, Table 8.16
http://www.spansion.com/Support/Datasheets/S25FL128S_256S_00.pdf
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the exact names for W25Q 0x40XX ID's flash parts, as the same
sizes of flashes comes with different ID's. so-that the distinguishes
becomes easy with this change.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Corrected the name of S25FL128S 64K sector part SPI flash,
S25FL128S supported has been added in below commit
"sf: spansion: Add support for S25FL128S"
(sha1: 1bfb9f156a)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Linker script is not able find start.o binary. So add its absolute path in
u-boot-spl.lds. This change is similar to u-boot-nand.lds
common/Makefile: Avoid compiling unnecssary files
fsl_ifc_spl.c : It is is responsible for reading u-boot binary from
NAND flash and copying into DDR. It also transfer control from NAND SPL
to u-boot image present in DDR.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
commit dfe64e2c89
Author: Sergey Lapin <slapin@ossfans.org>
Date: Mon Jan 14 03:46:50 2013 +0000
mtd: resync with Linux-3.7.1
changed the initialization of BBT options. Fix drivers
jz4740 and s3c2410 which have not been updated yet and
cause compile errors.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Commit dfe64e2c89:
mtd: resync with Linux-3.7.1
broke the docg4 driver. Specifically:
- some of the prototypes of the ecc methods changed
- the NAND_NO_AUTOINCR flag was removed
- the ecc.strength element was added.
This patch fixes these. Tested on the docg4 on my palmtre680 board.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
This patch corrected the nr_blocks used for W25Q32DW SPI flash.
nr_blcoks are incorrectly assigned on below patch
"sf: winbond: add W25Q32DW"
(sha1: 772ba15474)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Add support for Winbond W25Q80BW SPI flash.
This patch corrected the flash name, nr_blocks and
also commit message header from below patch.
"sf: winbond: add W25Q32"
(sha1: c969abc470)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
As the per the ID tabl the flash is under Uniform 64-kB sector
architecture, hence updated with proper name.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This patch adds a print messages while using 'sf read' and
'sf write' commands to make sure that how many bytes read/written
from/into flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Tom Rini <trini@ti.com>
This patch adds a print messages while using 'sf erase' command
to make sure that how many bytes erased in flash device.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Tom Rini <trini@ti.com>
Missing return after memcpy is done for memory-mapped SPI flashes,
hence added retun 0 after memcpy done.
The return is missing in below patch
"sf: Enable FDT-based configuration and memory mapping"
(sha1: bb8215f437)
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Acked-by: Simon Glass <sjg@chromium.org>
This patch is essentially an update of u-boot MTD subsystem to
the state of Linux-3.7.1 with exclusion of some bits:
- the update is concentrated on NAND, no onenand or CFI/NOR/SPI
flashes interfaces are updated EXCEPT for API changes.
- new large NAND chips support is there, though some updates
have got in Linux-3.8.-rc1, (which will follow on top of this patch).
To produce this update I used tag v3.7.1 of linux-stable repository.
The update was made using application of relevant patches,
with changes relevant to U-Boot-only stuff sticked together
to keep bisectability. Then all changes were grouped together
to this patch.
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
[scottwood@freescale.com: some eccstrength and build fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Add support for Winbond's W25PXX SPI flash.
These devices is used on Faraday A369 evaluation board.
Signed-off-by: Kuo-Jung Su <dantesu@faraday-tech.com>
CC: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
CC: Tom Rini <trini@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add support for Winbond W25Q256 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This is a S25FL064A successor. It supports up to 104MHz bus
speed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
SPANSION recommend S25FL128S supersedes S25FL129P, and the two flash
memory have the same device ID and Memory architecture. So they can
use the same config parameters.
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
When base address given was out of valid flash address ranges,
flash_get_info() function returned the pointer to the last
element of flash_info[i] array.
This patch changes this function to return NULL pointer
in such a case, which is more correct behaviour.
The function flash_protect_default() calls flash_protect()
immediately after flash_get_info() invocation.
With this correction, flash_protect() function would be
able to return soon, for NULL flash_info.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Linux Kernel Documentation/CodingStyle says:
Do not add a space after unary operators such as &, *, ...
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Packed structure cfi_qry contains unaligned 16- and 32-bits members,
accessing which causes problems when cfi_flash driver is compiled with
-munaligned-access option: flash initialization hangs, probably
due to data error.
Since the structure is supposed to replicate the actual data layout
in CFI Flash chips, the alignment issue can't be fixed in the structure.
So, unaligned fields need using of explicit unaligned access macros.
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-By: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Stefan Roese <sr@denx.de>
When a all 0xFF buffer is passed to drop_ffs, the no-0xFF check loop
will loop forever.
After the fix, If ssize_t i = -1 and size_t l = i + 1, the value of l
will still be 0 as expected.
Signed-off-by: Tao Hou <hotforest@gmail.com>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: Scott Wood <scottwood@freescale.com>
When writelen is mtd->writesize - 1, it is still a partial page write
Signed-off-by: Tao Hou <hotforest@gmail.com>
Cc: Scott Wood <scottwood@freescale.com>
This avoids needing a separate U-Boot config when some revisions
of a board have small-page NAND and other revisions have large-page
NAND (except for NAND SPL targets).
CONFIG_FSL_ELBC_FMR is removed -- it was never used nor documented, and
it gets in the way of this change.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch adds driver for the gigabyte devices
GD25LQ and GD25Q64B required for Snow Board.
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The manual resolution in commit ec7023db wrongly removed functions
nand_init and nand_deselect from file drivers/mtd/nand/mxc_nand_spl.c.
Revert this removal.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch adds a driver for the diskonchip G4 nand flash device. It is based
on the driver from the linux kernel.
This also includes a separate SPL driver. A separate SPL driver is used because
the device operates in a different mode (reliable mode) when loading a boot
image, and also because the storage format of the boot image is different from
normal data (pages are stored redundantly). The SPL driver basically mimics how
a typical IPL reads data from the device. The special operating mode and
storage format are used to compensate for the fact that the IPL does not contain
the BCH ecc decoding algorithm (due to size constraints). Although the u-boot
SPL *could* use ecc, it operates like an IPL for the sake of simplicity and
uniformity, since the IPL and SPL share the task of loading the u-boot image.
As a side benefit, the SPL driver is very small.
[port from linux kernel 3.4 commit 570469f3bde7f71cc1ece07a18d54a05b6a8775d]
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Add support for generic NAND SPL via the SPL framework into the
mxc_nand_spl driver. This is basically just a simple rename and
publication of the already implemented functions. To avoid the
bare-bones functions getting in the way of the NAND_SPL, build
them only if CONFIG_SPL_FRAMEWORK is not defined.
Also make sure the requested payload is aligned to full pages,
otherwise this simple driver fails to load the last page.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Delete all occurrences of hang() and provide a generic function.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
[trini: Modify check around puts() in hang.c slightly]
Signed-off-by: Tom Rini <trini@ti.com>
The following headers are moved to a i.MX common location:
- regs-common.h
- regs-apbh.h
- regs-bch.h
- regs-gpmi.h
- dma.h
This way this header can be re-used also by other i.MX platforms.
For example the i.MX6 which will need it for the upcoming NAND
support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
If CONFIG_NAND_ECC_BCH is set use 4-bit error correction code instead of
the 1-bit error correction code on the NAND device.
Signed-off-by: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
This also fixes support for mx31pdk and tx25, which had been broken by commit
e05e5de7fa.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
The syndrome functions should use the page number passed as argument instead of
the page number saved upon NAND_CMD_READ0.
This does not make any difference if the NAND_NO_AUTOINCR option is set, but
otherwise this fixes accesses to the wrong pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
The page number indicated in the debug trace of mxc_nand_read_oob_syndrome() did
not match the page being worked on.
By the way, replace the GCC-specific __FUNCTION__ with __func__.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Add some abstraction to NFC definitions so that some parts of the current code
can also be used for future i.MX5 code.
Clean up a few things by the way.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently is_16bit_nand() is a per SoC function and it decides the bus nand
width by reading some boot related registers.
This method works when NAND is the boot medium, but does not work if another
boot medium is used. For example: booting from a SD card and then using NAND
to store the environment variables, would lead to the following error:
NAND bus width 16 instead 8 bit
No NAND device found!!!
0 MiB
Use CONFIG_SYS_NAND_BUSWIDTH_16BIT symbol to decide the bus width.
If it is defined in the board file, then consider 16-bit NAND bus-width,
otherwise assume 8-bit NAND is used.
This also aligns with Documentation/devicetree/bindings/mtd/nand.txt, which
states:
nand-bus-width : 8 or 16 bus width if not present 8
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Introduce CONFIG_SYS_NAND_BUSWIDTH_16BIT option so that other NAND controller
drivers could use it when a 16-bit NAND is deployed.
drivers/mtd/nand/ndfc has CONFIG_SYS_NDFC_16BIT, so just rename it, so that
other NAND drivers could reuse the same symbol.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
The unwind code was not reversing operations correctly and was causing
a hang on any error condition.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
We make these two functions take a size_t pointer to how much space
was used on NAND to read or write the buffer (when reads/writes happen)
so that bad blocks can be accounted for. We also make them take an
loff_t limit on how much data can be read or written. This means that
we can now catch the case of when writing to a partition would exceed
the partition size due to bad blocks. To do this we also need to make
check_skip_len count not just complete blocks used but partial ones as
well. All callers of nand_(read|write)_skip_bad are adjusted to call
these with the most sensible limits available.
The changes were started by Pantelis and finished by Tom.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Tom Rini <trini@ti.com>
The kernel states:
---8<---
The OMAP3 GPMC hardware BCH engine computes remainder polynomials, it does not
provide automatic error location and correction: this step is implemented using
the BCH library.
--->8---
And we do so in u-boot.
This implementation uses the same layout for BCH8 but it is fix. The current
provided layout does only work with 64 Byte OOB.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Ilya Yanok <ilya.yanok@cogentembedded.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Mansoor Ahamed <mansoor.ahamed@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
With uppcoming BCH support on OMAP devices we need to decide between differnt
algorithms when switching the ECC engine. Currently we support 1-bit hammign
and 8-bit BCH on HW backend.
In order to switch between differnet ECC algorithms we need to change the
interface of omap_nand_switch_ecc() also.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Thomas Weber <thomas.weber.linux@googlemail.com>
arch/arm/include/asm/arch-am33xx/omap_gpmc.h and
arch/arm/include/asm/arch-omap3/omap_gpmc.h are almost the same, consolidate
the common parts into a new header.
Introduce a new asm/omap_gpmc.h which defines the command part and pulls in
the architecture specific one.
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Tom Rini <trini@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
This fixes this build warning:
Configuring for qemu_mips64 - Board: qemu-mips64, Options: SYS_BIG_ENDIAN
text data bss dec hex filename
215344 13082 218720 447146 6d2aa qemu_mips64/u-boot
cfi_flash.c: In function 'flash_map':
cfi_flash.c:217:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch addjusted the write buffer size for M29EW devices those
are operated in 8-bit mode.
The M29EW devices seem to report the CFI information wrong when
it's in 8 bit mode.
There's an app note from Numonyx on this issue and there's a patch
in the open source as well for Linux, but it doesn't seem to be in mainline.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
This commit is based on that patch from aaron.williams@caviumnetworks.com
with same commit title. pulled the same code changes into current u-boot tree.
http://patchwork.ozlabs.org/patch/140863/http://lists.denx.de/pipermail/u-boot/2011-April/089606.html
This patch corrects the addresses used when working with Spansion/AMD FLASH chips.
Addressing for 8 and 16 bits is almost identical except in the 16-bit case the
LSB of the address is always 0. The confusion arose because the addresses
in the datasheet for 16-bit mode are word addresses but this code assumed it was
byte addresses.
I have only been able to test this on our Octeon boards which use either an 8-bit
or 16-bit bus. I have not tested the case where there's an 8-bit part on a 16-bit
bus.
This patch also adds some delays as suggested by Spansion.
If a part can be both 8 and 16-bits, it forces it to work in 8-bit mode if an
8-bit bus is detected.
Apart from the pulled changes, fixed few minor code cleanups and tested
on 256M29EW, 512M29EW flashes.
Before this fix:
---------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0xFF, Device ID: 0xFF
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
After this fix:
--------------
Bank # 1: CFI conformant flash (8 x 8) Size: 64 MB in 512 Sectors
AMD Standard command set, Manufacturer ID: 0x89, Device ID: 0x7E2301
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Aaron Williams <aaron.williams@caviumnetworks.com>
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Tested-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Add support for Winbond W25Q32DW 32Mbit part
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
- In arch/arm/cpu/armv7/omap-common/timer.c,
drivers/mtd/nand/omap_gpmc.c and drivers/net/cpsw.c add #include files
that the driver needs but had been relying on <config.h> to bring in.
- In arch/arm/cpu/armv7/omap-common/lowlevel_init.S add <config.h>
- In am335x_evm.h and pcm051.h don't globally include
<asm/arch/hardware.h> and <asm/arch/cpu.h> but just <asm/arch/omap.h>
as that is the only include which defines things the config uses.
Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: Tom Rini <trini@ti.com>
Enable device tree control of SPI flash, and use this to implement
memory-mapped SPI flash, which is supported on Intel chips.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some SPI flash controllers (e.g. Intel ICH) have a limit on the number of
bytes that can be in a write transaction. Support this by breaking the
writes into multiple transactions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Rather than each device having its own way to allocate a SPI flash
structure, use the new allocation function everywhere. This will make it
easier to extend the interface without breaking devices.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present it is difficult to extend the SPI flash structure since
all devices allocate it themselves, and few of them zero all fields.
Add a new function spi_flash_alloc() which can be used by SPI devices
to perform this allocation, and thus ensure that all devices can
better cope with SPI structure changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Tested with an IGEPv2 board seems that current onenand_spl_load_image implementation
doesn't work. This patch fixes this function changing the read loop and reading the
onenand blocks from page to page.
Tested with various IGEP based boards with a OneNAND from Numonyx.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
If the NAND is locked tight, commands such as lock and unlock will not
work, but the NAND chip may not report an error. Check the lock tight
status before attempting such operations so that an error status can be
reported if we know the operation will not succeed.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
If CONFIG_NAND_ECC_BCH is set we use 4-bit error corretion code
instead of the 1-bit error correction code on the NAND device
within this driver.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Add support for Numonyx N25Q256A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q32A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q32 SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Numonyx N25Q64A SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for Winbond's W25Q64W SPI flash.
This device is used on xilinx zynq emulation platform.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch corrected the first byte of idcode1 for S25FL256S SPI flash.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Not only Spansion supports the Persistent Protection Bits (PPB) locking.
Other devices like the Micron JS28F512M29EWx also support this type
of locking/unlocking. Detection of support is done in the same way as
done for the Spansion chips - via the 0x49 CFI word.
This patch enables this PPB protection mechanism for all AMD type
(AMD commandset) chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Patch 66863b05 [cfi_flash: add support for Spansion flash PPB sector
protection] introduced the PPB (Persistent Protection Bit) locking for
Spansion chips. But right now the sector protection status (locked vs
unlocked) is set to unlocked for all sectors upon bootup. The real
sector protection status is ignored.
This patch now reads the current sector protection status and uses
it for these AMD/Spansion flash chips.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Holger Brunck <holger.brunck@keymile.com>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Consolidate manufacturer matching into the function manufact_match()
and use it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Holger Brunck <holger.brunck@keymile.com>
Add support for SST 4KB sector granularity.
Many recent SST flashes, i.e. SST39VF3201B and similar of this family
are declared CFI-conformant from SST. They support CFI query, but implement
2 different sector sizes in the same memory: a 64KB sector (they call it
"block", std AMD erase cmd=0x30), and a 4KB sector (they call it "sector",
erase cmd=0x50). Also, CFI query on these chips, reading from address 0x2dh
of cfi query struct, detects a number of secotrs for the 4KB granularity
(flinfo shows it).
For all other aspects, they are CFI compliant, so, as Linux do, i think
it's a good idea to handle these chips in the CFI driver, with a fixup
to allow 4KB granularity, as should be expected, instead of 64KB.
Signed-off-by: Angelo Dureghello <sysamfw@gmail.com>
Signed-off-by: Stefan Rose <sr@denx.de>
IFC_FIR_OP_CMD0 issues command for execution without checking flash
readiness. It may cause problem if flash is not ready. Instead use
IFC_FIR_OP_CW0 which Wait for tWB time and poll R/B to return high or
time-out, before issuing command.
NAND_CMD_READID command implemention does not fulfill above requirement. So
update its programming.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Hemant Nautiyal <hemant.nautiyal@freescale.com>
It could happen (1 out of 100 times) that NAND did not start up correctly after
warm rebooting, so we end up with various failures or DMA timed out due to a
stalled BCH. When resetting BCH together with GPMI, the issue could not be
observed anymore (after 10000+ reboots). We probably need the consistent state
already before sending commands to NAND. This behaviour was observed in barebox
and kernel, so I assume it affects U-Boot as well. I chose to keep the extra
reset for BCH when changing the flash layout to be on the safe side.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Marek Vasut <marex@denx.de>
AM33XX with BCH8 can't work with nand_spl_simple correctly
because custom read_page implementation is required for proper
syndrome generation.
This simple driver mostly duplicates nand_spl_simple but has
nand_read_page changed to suit our needs.
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds support for BCH8 error correction code to omap_gpmc
driver. We use GPMC to generate codes/syndromes but we need ELM to find
error locations from given syndrome.
Signed-off-by: Mansoor Ahamed <mansoor.ahamed@ti.com>
[ilya: merge it with omap_gpmc driver, some fixes and cleanup]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch adds a NAND Flash torture feature, which is useful as a block stress
test to determine if a block is still good and reliable (or should be marked as
bad), e.g. after a write error.
This code is ported from mtd-utils' lib/libmtd.c.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
[scottwood@freescale.com: removed unnec. ifdef and unwrapped error strings]
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND Flash is erased by blocks, not by pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
This patch cleans up nand_util.c:
- Fix tabs.
- Fix typos.
- Remove space character before opening parenthesis in function calls.
- Fix comments.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Use a flag instead of a hard-coded macro so that sub-page reads can be
enabled in other cases (such as on-die ecc).
This is the same as a5ff4f102937a3492bca4a9ff0c341d78813414c in Linux
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[scottwood@freescale.com: fix fsl_ifc_sram_init prototype]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Document parameters used for specifying the NAND image to be loaded.
Also fix the definition of CONFIG_SPL_NAND_SIMPLE -- it's only
nand_spl_simple.c, not the entire nand directory. The word "simple" is
there for a reason. :-)
Signed-off-by: Scott Wood <scottwood@freescale.com>
---
v2: updated for makefile changes earlier in patchset
Some small SPLs do not use nand_base.c, and a subset of those also
require a special driver. Some SPLs need software ECC but others can't
fit it.
All existing boards that specify CONFIG_SPL_NAND_SUPPORT have these
symbols added to preserve existing behavior.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: use positive logic for including bits of NAND, rather than
a MINIMAL symbol that excludes things.
nand_ecc.c:82:5: warning: symbol 'nand_calculate_ecc' was not declared. Should it be static?
nand_ecc.c:155:5: warning: symbol 'nand_correct_data' was not declared. Should it be static?
nand_base.c:2854:1: error: directive in argument list
nand_base.c:2856:1: error: directive in argument list
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
cfi_flash.c:756:43: warning: Using plain integer as NULL pointer
cfi_flash.c:1150:52: warning: cast to non-scalar
cfi_flash.c:1433:46: warning: cast truncates bits from constant value (890089 becomes 89)
cfi_flash.c:1490:61: warning: cast truncates bits from constant value (1f001f becomes 1f)
cfi_flash.c:1508:61: warning: cast truncates bits from constant value (10001 becomes 1)
cfi_flash.c:1738:63: warning: cast truncates bits from constant value (10001 becomes 1)
cfi_flash.c:1857:6: warning: symbol '__flash_cmd_reset' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
Add the missing bits to the Tegra NAND driver to make ONFI detection work
properly.
Also add it to the Tegra default config, as it seems to be a reasonable thing
to have it available on all boards that use any kind of NAND.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Boards may require a different pinmux setup for NAND than the default one.
Add a way to call into board specific code to set this up.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The move is pretty straight-forward. ap20.h and tegra20.h were renamed to ap.h and tegra.h.
Some files remain in arch-tegra20 but 'include' a file in 'arch-tegra' with #defines & structs
that will be common between T20 and T30 HW. HW-specific #defines, etc. stay in the 'arch-tegra20'
'root' file.
All boards build OK w/MAKEALL -s tegra20. Checkpatch.pl runs clean. Seaboard works OK.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Due to grown code sizes the TQM85xx boards don't build any more with
some older tool chains (like ELDK 4.2). As these boards have long
reached EOL it seems a waste of effort trying to fix them. The vendor
has agreed to drop support for them, too. So let's get rid of them.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
Use the same IP revisions as in Linux in order to make the comparison more
clear.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Merge mxc_setup_config1() into board_nand_init() in order to ease the addition
of i.MX5 support in the following patches.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mxc_nand_read_page_raw_syndrome() should reenable ECC upon exit. This fixes ECC
errors left uncorrected after a call to this function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use _mxc_nand_enable_hwecc() instead of duplicating its code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the NFC IP 1.1, the 32-bit ecc_status_result value comes from 2
consecutive 16-bit registers. This patch reads all the fields of this value,
which makes a difference for 4-kiB NF pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is based on Linux kernel -next:
commit 14f44abf1dafc20ba42ce8616a8fc8fbd1b3712b
Author: Brian Norris <computersforpeace@gmail.com>
Date: Fri Jul 13 09:28:24 2012 -0700
mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND_CMD_ constants for lock/unlock should be in the header
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
This is commit 637957551c0ac80de8dfc7650d320c5a98c2c0c0 from Linux
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[scottwood@freescale.com: picked from Linux into U-Boot]
Reported-by: Rafael Beims <rafael.beims@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Using common spi flash operation function to replace private operation
funtion
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
With Simon Glass's include/nand.h alignment changes, some mxs builds
were generating errors. Fix is to ensure asm/cache.h is included before
linux/mtd/nand.h. Moving common.h to top of include list does that.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
A device tree is used to configure the NAND, including memory
timings and block/pages sizes.
If this node is not present or is disabled, then NAND will not
be initialized.
Signed-off-by: Jim Lin <jilin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The NAND layer needs to use cache-aligned buffers by default. Towards this
goal. align the default buffers and their members according to the minimum
DMA alignment defined for the architecture.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Check for ctrlc() in operations that take time and loop over the flash
addresses.
In netconsole, tstc() is expensive. Only check once in a while to not
slow down the operation significantly.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added an optional check in the CFI driver to evaluate if the sector is
already blank before issuing an erase command. Improves erase time by
over a factor of 10 if already blank.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.
To use PMECC in this driver, the user needs to set the PMECC correction
capability, the sector size and ROM lookup table offsets in board config file.
This driver is ported from Linux kernel atmel_nand PMECC patch. The main difference
is in this version it uses registers structure access hardware instead of using macros.
It is tested in 9x5 serial boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
This patch
1. extract the hwecc initialization code into one function. It is a preparation for adding atmel PMECC support.
2. enable CONFIG_SYS_NAND_SELF_INIT. Which make us can configurate the ecc parameters between nand_scan_ident() and nand_scan_tail().
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[fix empty newline at EOF error and move return value check into ifdef]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The sys_proto.h functions (except the boot modes) are compatible with
i.MX233 and i.MX28 so we use 'mxs' prefix for its methods.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Orjan Friberg wrote at [1]:
"For the beagleboard, ecc.size is not explicitly set when doing 'nandecc
sw'. If it's not set for the NAND_ECC_SOFT case in nand_scan_tail, it's
set to 256 bytes.
When doing 'nandecc hw', ecc.size is set to 512 bytes. Hence, when
changing back to 'nandecc sw' ecc.size remains at 512 bytes and suddenly
the format has changed."
No patch has been submitted and the issue was still present. This patch
adds the mentioned solution. Tested on a tam3517 board.
[1] http://lists.denx.de/pipermail/u-boot/2012-February/119002.html
cc: Orjan Friberg <of@flatfrog.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
* 'sf' of git://git.denx.de/u-boot-blackfin:
sf: spansion: Add support for S25FL256S
sf: winbond: fix page_size
sf: stmicro: add support for N25Q128A
sf: stmicro: add support N25Q128 parts
sf: stmicro: support JEDEC standard two-byte signature
sf: winbond: add W25Q32
cmd_spi: remove superfluous semicolon
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit a4ed3b6 "sf: inline data constants" modified winbond.c's page_size
from 256 to 4096. This prevents either/both of "sf write" writing the
correct data, or "sf read" from reading the correct data back.
This allows U-Boot running on Compulab Tegra to upgrade itself.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
commit 54652991
Work around bug in Numonyx P33/P30 256-Mbit 65nm flash chips
fixes a problem for Numonyx P33/P30 flashes for 256-Mbit, but this leads
to problems for smaller versions of this chip e.g. the 32Mbit version
with deviceid 0x16 on mgcoge. So move the code for this work around to
an own function and check previously manufacturer id and device id to
not break other flashes which don't need this work around.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Stefan Roese <sr@denx.de>
cc: Philippe De Muyter <phdm@macqel.be>
cc: Gerlando Falauto <gerlando.falauto@keymile.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Erasing flash sectors protected with persistent protection bit (PPB)
mechanism on Spansion flash chips doesn't work. Add sector protection
status checking and sector lock and unlock commands to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Adds support for Numonyx's N25Q128 SPI flash. These devices
are used on (among others) Avnet Spartan-6 LX9 micro-evaluation
boards. Tested with "sf" commands and CONFIG_ENV_IS_IN_SPI_FLASH.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
There are more than the M25Pxx serial flashs that can be
used with the stmicro driver, for example: the M25PXxx or
N25Qxx serie. All these chips have burned in the original
stmicro manufacture id 0x20 together with a standard
two-byte signature.
In preperation to support all these chips the stmicro driver
have to decode the full two-byte signature.
Signed-off-by: Stephan Linz <linz@li-pro.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
SMDK EVT1 has a different Winbond part, added its part details
to the SPI flash table.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Note: because 4-byte addressing is not supported yet,
at the moment only the first 16MiB of the device are available.
Signed-off-by: Jérôme Carretero <cJ@zougloub.eu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The only two drivers to write the status register do it in the same
way, so unify the implementations. This also makes the block unlock
logic the same.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The local sst enable/disable write funcs don't really add anything
over the common API, so just inline the common calls directly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Analysis of the flash drivers shows that they all use 0x20 if the erase
size is 4KiB, or 0xd8 if it's larger. So with this info in hand, we can
unify all the erase functionality in one place.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
I imagine much of these constants are due to copy & pasting previous
drivers rather than an actual reflection of the hardware layout. At
any rate, inline the info that we don't care about externally as it
shrinks things nicely.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In an effort to unify the spi flash drivers further, drop all the
unused and/or duplicate command defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Needed for redundant environment for example.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Amit Virdi <amit.virdi@st.com>
Cc: Vipin Kumar <vipin.kumar@st.com>
There are two problems in the current timeout loop implementation:
1. In case initial test failing, there will always be a delay of 1 ms
2. The delay duration is not tunable
The new implementation addresses both these limitations.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
If the flash size was smaller than 1MB then flash_print_info()
was erroneously reporting 0 MB.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
THis patch introduces a new methodology for flash probing
in which flash_devices[] table, looked-up thru the dev_id, is
used to locate the flash geometry and information.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Since the smi erase code is very generic and works for any kind
of flash, there is no need to test for ST_M25Pxx_ID flash types
like m25p40 flashes).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
smi_read_sr fails sometimes because of TFF not getting set within assumed time.
This condition may arise because of, for example, smi memory being in a erase
mode.
This fix is to enable reading the status register until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SMI driver read status fails because the control register could not be
overwritten. Instead, the read status should be tried until timeout.
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This commit does the following:
- Reports error if SNOR flash is not found on the board
- Changes smi_read_sr to return error using which a retry mechanism is
implemented for reading flash status
Signed-off-by: Vipin Kumar <vipin.kumar@st.com>
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Stefan Roese <sr@denx.de>