Enable OF_CONTROL and DM for gpio and pin control support
on the i.MX6SX based Udoo Neo.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Import the i.MX6SX based UDOO Neo dts files from Linux 5.12-rc1
and sync the i.MX6SX pinfunc.h
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Francesco Montefoschi <francesco.montefoschi@udoo.org>
Cc: Breno Lima <breno.lima@nxp.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add support for stack protector for UBOOT, SPL, and TPL
as well as new pytest for stackprotector
Signed-off-by: Joel Peshkin <joel.peshkin@broadcom.com>
Adjust UEFI build flags.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The current usage of the variable CFLAGS_NON_EFI on the x86 architecture
deviates from other architectures.
Variable CFLAGS_NON_EFI is the list of compiler flags to be removed when
building UEFI applications. It is not a list of flags to be added anywhere.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
regmap_read() only fills the first two bytes of val. The last two bytes are
random data from the stack. This means the test will fail randomly.
For low endian systems we could simply initialize val to 0 and get correct
results. But tests should not depend on endianness. So let's use a pointer
conversion instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
U-boot might display wrong module revision information
for modules with an assembly version 'K'. "cfgblock create"
does not takes into account all revision digits from PID8.
This fix takes into account all digits of PID8
to store module revision.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Use psci driver exported functions for reset/poweroff, instead of
invoking directly invoke_psci_fn.
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Adds support for:
* PSCI_FEATURES, which was introduced in PSCI 1.0. This provides API
that allows discovering whether a specific PSCI function is implemented
and its features.
* SYSTEM_RESET2, which was introduced in PSCI 1.1, which extends existing
SYSTEM_RESET. It provides support for vendor-specific resets, providing
reset_type as an additional param.
For additional details visit [1].
Implementations of some functions were borrowed from Linux PSCI driver
code [2].
[1] https://developer.arm.com/documentation/den0022/latest/
[2] drivers/firmware/psci/psci.c
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Rob does not have access to any Calxeda systems anymore, also has
expressed a lack of interest in those systems in the past.
I have multiple working Midway nodes under my desk in the office, so
am happy to take over maintainership.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far U-Boot was hard coding a (surely sufficient) memory size of 512
MB, even though all machines out there have at least 4GB of DRAM.
Since U-Boot uses its memory knowledge to populate the EFI memory map,
we are missing out here, at best losing everything beyond 4GB on Midway
boxes (which typically come with 8GB of DRAM).
Since the management processor populated the DT memory node already with
the detected DRAM size and configuration, we use that to populate
U-Boot's memory bank information, which is the base for the UEFI memory
map.
This finally allows us to get rid of the NR_DRAM_BANKS=0 hack, that we
had in place to avoid U-Boot messing up the DT memory node before
loading the kernel.
Also, to cover the whole of memory, we need to enable PHYS_64BIT.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far we were defining a somewhat confusing PHYS_SDRAM_1_SIZE variable,
which originally was only used for setting the memtest boundaries. This
definition in highbank.h has been removed about a year ago (moved to
Kconfig), so we also don't need the hard-coded size definition any longer.
Get rid of the misleading memory size definition, which was actually wrong
anyway (it's 4088 MB for those machines with just 4GB of DRAM).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
To squash that nasty warning message and make better use of the newly
gained OF_CONTROL feature, let's convert the calxedagmac driver to the
"new" driver model.
The conversion is pretty straight forward, mostly just adjusting the
use of the involved data structures.
The only actual change is the required split of the receive routine into
a receive and free_pkt part.
Also this allows us to get rid of the hardcoded platform information and
explicit init calls.
This also uses the opportunity to wrap the code decoding the MMIO
register base address, to make it safe for using PHYS_64BIT later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
All Calxeda machines are actually a poster book example of device tree
usage: the DT is loaded from flash by the management processor into
DRAM, the memory node is populated with the detected DRAM size and this
DT is then handed over to the kernel.
So it's a shame that U-Boot didn't participate in this chain, but
fortunately this is easy to fix:
Define CONFIG_OF_CONTROL and CONFIG_OF_BOARD, and provide a trivial
function to tell U-Boot about the (fixed) location of the DTB in DRAM.
Then enable DM_SERIAL, to let the PL011 driver pick up the UART platform
data from the DT. Also define AHCI, to bring this driver into the driver
model world as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
So far on Highbank/Midway machines U-Boot only ever uses 512MB of DRAM,
even though the machines have typically 4GB and 8GB, respectively.
That means that so far we didn't need an extra limit for placing the DTB
and initrd, as the 512MB are lower than the kernel's limit ("lowmem",
typically 768MB).
With U-Boot now needing to learn about the actual memory size (to
correctly populate the EFI memory map), it might relocate fdt and initrd
to the end of DRAM, which is out of reach of the kernel.
So add limiting values to the fdt_high and initrd_high environment
variables, to prevent U-Boot from using too high addresses.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Document the bindings for fsl,anatop-regulator
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Anatop is an integrated regulator inside i.MX6 SoC.
There are 3 digital regulators which controls PU, CORE (ARM), and SOC.
And 3 analog regulators which controls 1P1, 2P5, 3P0 (USB).
This patch adds the Anatop regulator driver.
Signed-off-by: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Reviewed-by: Sean Anderson <sean.anderson@seco.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Trying to compile with CONFIG_CMD_MMC=y and CONFIG_MMC=n leads to errors:
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmcops':
cmd/mmc.c:984: undefined reference to `get_mmc_num'
riscv64-linux-gnu-ld.bfd: cmd/built-in.o: in function `do_mmc_setdsr':
cmd/mmc.c:873: undefined reference to `find_mmc_device'
Add missing dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The fdt node offset is apparently not set properly when probed
causing no MDIO busses to be found. Fix this by obtaining the
offset.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
After check for maximum between max id and available ports, also check
if available port count is less than max id and update.
In the case of the CN8030 OcteonTX SoC max_id needs to be reduced to
the number of ports found otherwise the following occurs on a scan:
GW6404-B> scsi scan
scanning bus for devices...
Target spinup took 0 ms.
AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl SATA mode
flags: 64bit ncq ilck stag pm led clo only pmp fbss pio slum part ccc
apst
Device 0: (0:0) Vendor: ATA Prod.: SanDisk SD8SFAT0 Rev: Z233
Type: Hard Disk
Capacity: 61057.3 MB = 59.6 GB (125045424 x 512)
"Synchronous Abort" handler, esr 0x96000006
elr: 000000000052f824 lr : 000000000052fa10 (reloc)
elr: 000000007fee9824 lr : 000000007fee9a10
x0 : 0000000000000001 x1 : 0000000000000001
x2 : 000000007bea3528 x3 : 000000007bea3580
x4 : 0000000000000200 x5 : 0000000000000000
x6 : 0000000000000002 x7 : 000000007bea3540
x8 : 00000000fffffff8 x9 : 0000000000000008
x10: 00000000000186a0 x11: 000000000000000d
x12: 0000000000000006 x13: 000000000001869f
x14: 0000000000000007 x15: 00000000ffffffff
x16: 000000007ff439a5 x17: 000000007ff5730c
x18: 000000007bea9de0 x19: 000000007ff7a580
x20: 000000007bec79f8 x21: 0000000000000000
x22: 000000007bea3580 x23: 0000000000000000
x24: 0000000000000000 x25: 000000007bec7a00
x26: 00000000ffffffc0 x27: 000000007bec79d0
x28: 000000007beb51c0 x29: 000000007bea3480
Code: 91246800 940130c2 12800000 1400004f (b9402ae0)
Resetting CPU ...
Signed-off-by: Suneel Garapati <sgarapati@marvell.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Revert a change that occured between the Marvell SDK-10.1.1.0
and SDK-10.3.1.1 which broke QSMII phy support.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Move CONFIG_SUPPORT_RAW_INITRD out of the octeontx_common header
and into the defconfig files.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Fixes IDE issues found on the Malta board under Qemu:
1) DMA implied commands were sent to the controller in stead of the PIO
variants. The rest of the code is DMA free and written for PIO operation.
2) direct pointer access was used to read and write the registers instead
of the inb/inw/outb/outw functions/macros. Registers don't have to be
memory mapped and ATA_CURR_BASE() does not have to return an offset from
address zero.
3) Endian isues in ide_ident() and reading/writing data in general. Names
were corrupted and sizes misreported.
Tested malta_defconfig and maltael_defconfig to work again in Qemu.
Signed-off-by: Reinoud Zandijk <reinoud@NetBSD.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
use 'select' to enable IRQ as it does not have architecture
specific dependency.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
UCLASS_IRQ driver is not Intel specific. Make CONFIG_IRQ
selectable for all platforms.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GICv3 RM requires "The first 1KB of memory for the LPI Pending tables
must contain only zeros on initial allocation, and this must be visible
to the Redistributors, or else the effect is UNPREDICTABLE".
And as the following statement, we here clear the whole Pending tables
instead of the first 1KB.
"An LPI Pending table that contains only zeros, including in the first 1KB,
indicates that there are no pending LPIs.
The first 1KB of the LPI Pending table is IMPLEMENTATION DEFINED. However,
if the first 1KB of the LPI Pending table and the rest of the table contain
only zeros, this must indicate that there are no pending LPIs."
And there isn't any pending LPI under U-Boot, so it's unnecessary to
load the contents of the Pending table during the enablement, then set
the GICR_PENDBASER.PTZ flag.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com> # NXP LS1028A
Reviewed-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Now we have PCIe, let's also enable NVMe to access an eventual NVMe SSDs
connected on the M.2 slot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Enable PCIe by default in u-boot, this should eventually be made dynamic
in the runtime board config depending on the MCU configuration.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The sync of the device tree and dt-bindings from Linux v5.6-rc2
11a48a5a18c6 ("Linux 5.6-rc2") causes Ethernet to break on some
ODROID-C2. The PHY seems to need proper reset timing to be functional
in U-Boot and Linux afterwards. Readd the old PHY reset bindings for
dwmac until we support the new bindings in the PHY node.
Fixes: dd5f2351e9 ("arm64: dts: meson: sync dt and bindings from v5.6-rc2")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmB9NEccHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyBp1CACFd9d7fokb59aFGeta
RaVD4Ni/5WUMT2ulUWYVn2KPmDLouXKZfvQZxakTJJkLCKfIKpQJ6pw82SUPqNc1
xhFS+YOxuDwhbB6ksApq7eUOga9T/K3S/8T4gPWkAOsAwlJGeF5AE1uxWFLbiNzt
eC2kMtRnwHmRq+fOuLsz1EHHKGcp+mtOnXEy2tv23xcGMqeCPzGsK7DWp1dw66gc
sqj7RdkfP/Ies557Ai/NjfdiOx1ThuVmNz/CgJgVf2/vHiQNgi4jHHDYQG55nGzJ
ExLtlom0L3ttko/hlznANFfPD6PBeF03T1cOT8jgx9/RFIF6dqDoA1YOa2dajhuW
xq5k
=MPfk
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2021.07-b' of https://source.denx.de/u-boot/custodians/u-boot-atmel
Second set of u-boot-atmel features for 2021.07 cycle:
This small feature set include support for 5th PIO bank on pio4 pinctrl
driver and a fix for the SPL on sama5d3.
This reverts commit 38d6b7ebda.
struct global_data contains a pointer to the bd_info structure. This
pointer was populated spl_set_bd() to a pre-allocated bd_info in the
".data" section. The referenced commit replaced this mechanism to one
that uses malloc(). That new mechanism is only used if SPL_ALLOC_BD=y.
which very few boards do.
The result is that (struct global_data)->bd is NULL in SPL on most
platforms. This breaks falcon mode, since arch_fixup_fdt() tries to
access (struct global_data)->bd and set the "/memory" node in the
devicetree. The result is that the "/memory" node contains garbage
values, causing linux to panic() as it sets up the page table.
Instead of trying to fix the mess, potentially causing other issues,
revert to the code that worked, while this change is reworked.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Now we have PCIe, let's also enable NVMe to access an eventual NVMe SSDs
connected on the M.2 slot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
