eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
mmc_send_status() is currently used to poll the card until it is ready, not
actually returning the status of the card.
Make it return the status and add another function to poll the card.
Also remove the 'extern' declaration in the mmc-private.h header to comply
with the coding standard.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This reverts commit 318a7a576b.
The last and only user of this callback had been the omap_hsmmc driver.
It is not used anymore. Removing the callback.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
This is not required. The MMC core sends CMD0 right after the
initialization and it serves the same purpose.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
It sometimes happen that the PSTATE register does not indicate that the
bus is ready when it really is. This usually happens after a mode switch.
In that case it makes sense to reset the FSM handling the CMD and DATA
Also reset the FSMs if the STATE register cannot be cleared. This also
sometimes happens after a mode switch.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The response type of CMD25 is R1 instead of R1b.
Signed-off-by: Akio Hirayama <hirayama.akio@socionext.com>
[masahiro: add log ]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Card detect function implemented for SDHCI framework.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch reads cd-gpio property from devicetree
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This patch reads card detect properties from device tree &
added mmc capability macros in mmc.h.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When MMC_TINY is enabled, support for only one MMC device
is provided. Boards that register more than one device,
will just write over mmc_static keeping only the last one
registered.
This commit prevents this, keeping only the first MMC
device created. A debug warning message is added, if nothing
else, as a hint/documentation for developers.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
The SPL_MMC_TINY implements feature-reduced MMC support
on SPL, and as such, it's more consistent and convenient
to find it as part of the SPL configuration.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
This patch solves warnings detected by setting W=1 when building.
Warnings type detected:
- [-Wmissing-prototypes]
- [-Wimplicit-fallthrough=]
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The fsl_esdhc driver was for Freescale eSDHC on MPC83XX/MPC85XX
initially. The later QoriQ series PowerPC processors (which were
evolutions of MPC83XX/MPC85XX), QorIQ series ARM processors, and
i.MX series processors were using this driver for their eSDHCs too.
For the two series processors, the eSDHCs are becoming more and
more different. We should have split it into two drivers, like them
(sdhci-of-esdhc.c/sdhci-esdhc-imx.c) in linux kernel.
This patch is just to create a fsl_esdhc_imx driver which is a copy
of fsl_esdhc driver for i.MX processors. We will convert i.MX processors
to use fsl_esdhc_imx, and clean up the two drivers separately in the
future patches.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
u-boot is trying to make CONFIG_BLK as a hard requirement
for DM_MMC. But now it's still not.
config BLK
bool "Support block devices"
depends on DM
default y if DM_MMC
When fsl_esdhc driver was reworked for DM_MMC support, DM_MMC
without CONFIG_BLK enabled wasn't considered. This patch is to
fix probe issue without CONFIG_BLK enabled.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
U-Boot code currently only applies this restriction to HS200 mode,
extend this to HS400 mode as well.
Currently U-Boot code not support accessing boot partition in HS200/400
mode. This needs more check.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For bcm7445 and bcm7260, this patch enables CONFIG_DM_MMC and updates
the bcmstb SDHCI driver to use the new driver model. This allows
removal of SDHCI configuration handling from bcmstb.c, and eliminates
a board removal compile warning.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Reviewed-by: Stefan Roese <sr@denx.de>
- Gen3 PCIe driver + enablement on Salvator-X platforms.
- Gen3 recovery SPL used to reload ATF/OpTee/U-Boot instead of minimon.
- SDHI HS400 fixes ported from latest BSP and datasheet.
PowerPC supports 32 bit address.
So adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Since Gen3 SDHI has an internal DS signal AC-spec violation in HS400 mode,
CRC-error may occur in read command in HS400 mode. This phoenomenon occurs
at low/high temperature.
To fix this, after completion of HS400 tuning, enable manual calibration.
However, Gen3 M3 Ver.1.2 or earlier and H3 1.x does not support HS400.
These SoC forcibly use HS200 mode by SoC attribute.
The DT adjustment of the tuning parameters is not supported until the
DT property names become clear.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Adapted from a patch by Takeshi Saito <takeshi.saito.xv@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
Clean up the whitespaces in macros, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Peng Fan <peng.fan@nxp.com>
This reverts commit 72a89e0da5, which
causes the imx53 HSC to hang as the eMMC is not working properly anymore.
The exact error message:
MMC write: dev # 0, block # 2, count 927 ... mmc write failed
0 blocks written: ERROR
imx53 is not using the DDR mode.
Debugging of pre_div and div generation showed that those values are
generated in a way, which is not matching the ones from working setup.
As the original patch was performing code refactoring, let's revert this
change, so all imx53 boards would work again.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This converts the following to Kconfig:
CONFIG_SUPPORT_EMMC_BOOT
As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:
xilinx_zynqmp_zc1275_revB
xilinx_zynqmp_zc1751_xm018_dc4
xilinx_zynqmp_zc1751_xm019_dc5
xilinx_zynqmp_zcu100_revC
xilinx_zynqmp_zcu102_rev1_0
xilinx_zynqmp_zcu102_revA
xilinx_zynqmp_zcu102_revB
xilinx_zynqmp_zcu104_revA
xilinx_zynqmp_zcu104_revC
xilinx_zynqmp_zcu106_revA
xilinx_zynqmp_zcu111_revA
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The Standard Host Controller Interface (SDHCI) specification version
3.00 adds support for Advanced DMA (ADMA) for both 64 and 32 bit widths
of DMA. ADMA2 uses a table of descriptors for aggregating DMA requests.
This significantly improves read and write throughput.
Add Support for the same.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
In preparation for addition of ADMA2 support, cleanup SDMA handling by
moving it to a new sdhci_prepare_dma() function. Also add a flags field
in sdhci_host to indicate if DMA is enabled.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The wp-gpios property is used for gpio, if this is set, the WP pin is muxed
to gpio function, can't be used as internal WP checking. However the codes
remain to use internal WP checking.
This patch changes to examine the "fsl,wp-controller" for enabling internal WP
checking, and "wp-gpios" for muxing to gpio.
Signed-off-by: Ye Li <ye.li@nxp.com>
When sd/mmc work at DDR mode, like HS400/HS400ES/DDR52/DDR50 mode,
the output clock rate is half of the internal clock rate.
This patch set the DDR_EN bit first for DDR mode, hardware divide
the usdhc clock automatically, then follow the original sdr clock
setting method.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The driver currently calculates the end address of cache flush operation
for the DMA descriptors by adding cacheline size to the start address of
the last DMA descriptor. This is not safe, as the cacheline size may be,
in some unlikely cases, smaller than the DMA descriptor size. Replace the
addition with roundup() applied on the end address of the last DMA
descriptor to round it up to the nearest cacheline size multiple.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The bounce_buffer_start() can return -ENOMEM in case memory allocation
failed. However, in that case, the bounce buffer address is the same as
the possibly unaligned input address, and the cache maintenance operations
were not applied to this address. This could cause subtle problems. Add
handling for the bounce_buffer_start() return value to prevent such a
problem from happening.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The current 4-minute data transfer timeout is misleading and broken.
Instead of such a long wait, calculate the timeout duration based on
the length of the data transfer. The current formula is the transfer
length in bits, divided by a multiplication of bus frequency in Hz,
bus width, DDR mode and converted the mSec. The value is bounded from
the bottom to 1000 mSec.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We either need to use IS_ENABLED(CONFIG_FOO) or CONFIG_IS_ENABLED(FOO).
IS_ENABLE(FOO) will always return false.
This commit fixes the comparison by using the CONFIG_IS_ENABLED(FOO)
syntax.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Some MediaTek SoC need an additional clock "source_cg". Enable
this new clock. We reuse the same clock name as in the kernel.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Acked-by: Ryder Lee <ryder.lee@mediatek.com>
On response type r1b, if DTIME is not defined or too short,
the Datatimeout and DPSM flag occurs. Like the DPSM is
activated all next data transfer will be frozen.
To avoid this freeze:
-The driver must define a DTIME on all r1b response type.
-DTIME of SDMMC must be defined for alls stop transmission
(for read and write request) even if MMC_RSP_BUSY is not set.
-If busy timeout occur, an abort request must be sent to
reinitialize the DPSM.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Initially the compatible string was wrongly set to "st,stm32f4xx-sdio".
Use compatible string used by kernel instead and identify mmci variant
using "arm,primecell-periphid" property.
Currently, the DM part of mmci driver is only used by STM32 SoCs,
that's why the switch case gets only one entry. It will be populated
easily with new variant in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add the DM_MMC-compatible DesignWare MMC driver support for Synopsys
ARC devboards. It is created to switch ARC devboards to use DM_MMC.
It required information such as clocks (Bus Interface Unit clock,
Card Interface Unit clock) and SDIO bus width.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Pbias voltage should match the IO voltage set for the SD card. With the
latest pbias change to 3.3V, update the capabilities and IO voltages
settings to 3.3V.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
After the commit b9a2a0e2e9 ("mmc: Add support for downgrading
HS200/HS400 to HS mode"), it add a parameter in mmc_set_card_speed()
which indicates that the HS200/HS400 to HS downgrade is happening.
During the HS400 initialization, first select to HS200, and config
the related clock rate, then downgrade to HS mode. So here also need
to config the downgrade value to be true for two reasons. First,
make sure in the function mmc_set_card_speed(), after switch to HS
mode, first config the clock rate, then read the EXT_CSD, avoid
receiving data of EXT_CSD in HS mode at 200MHz. Second, after issue
the MMC_CMD_SWITCH command, it need to wait a bit then switch bus
properties.
Test on i.MX8QM MEK board, some Micron eMMC will stuck in transfer
mode in this case, and USDHC will never get data transfer complete
status, cause the uboot hang.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
On 16bit variants of the TMIO SD IP, the SECCNT register can only be
programmed to 16bit values, while on the 32bit and 64bit variants it
can be programmed to 32bit values. The SECCNT register indicates the
maximum number of blocks in a continuous transfer. Hence, limit the
maximum continuous transfer block count to 65535 blocks on 16bit
variants of the TMIO IP and to BIT(32)-1 blocks on 32bit and 64bit
variants.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set MMCIF clock rate to 97.5 MHz, which is the default according
to Gen2 datasheet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The tiny printf implementation only supports %x format specifier,
it does not support %X . Since it makes little difference whether
the debug output prints hex numbers in capitals or not, change it
to %x and make the MMC_TRACE output work with tiny printf too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
According to latest specification rev.0026 and after confirmation with
HW engineer, the DTCNTL register TAPNUM field must be set to 8 even on
H3 ES2.0 SoC. Make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
According to latest specification rev.0026, when HOST_MODE bit 0
(WMODE) is not set, HOST_MODE bit 8 (BUSWIDTH) is ignored. Clear
HOST_MODE bit 8 in such case and align the code with Linux and
avoid possible unforeseen issues.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Poll for iDMAC TX/RX interrupt before disable DMA.
This to prevent disable DMA before data is transfer
completed.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
The DT2FF register must be configured differently for HS400 mode
and for HS200/SDR104 mode. Configure the DT2FF register according
to the recommended datasheet settings for each mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Set the HOST_MODE register WMODE bit according to the SDHI bus width,
that is 0 for 64bit bus and 1 for 16/32bit bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Older kernel versions or systems which do not connect eMMC reset line
properly may not be able to handle situations where either the eMMC
is left in HS200/HS400 mode or SD card in UHS modes by the bootloader
and may misbehave. Downgrade the eMMC to HS/HS52 mode and/or SD card
to non-UHS mode before booting the kernel to allow such older kernels
to work with modern U-Boot.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
Since the fsl_esdhc will also be used by SPL, make the
preprocessor switches more generic to allow any kind of build.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Common sound support
buildman environment support
of-platdata documentation improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlxf7igRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYKfggApQiL0Gv6NdGAQN+zfpjKY5a2QyjKsAxa
KLm3q8XyXIQXufMWOEPoW1iWm0iixpIFgChy8ff3m/OPDzsx99UXDTyvjitsSxtQ
5tFu8K78nUZT6OOE3HNhhlyW/xK442oKBzGt4MUt3kUZOELsCNuftgbJUWksHuO3
6pPrgt36E0uRGbUA4ioYCU336viJRPOOCdqb8hHViEihFj/IEv5T82RdE5y97YxG
dT7BZxjPkBH5ZN1uD/tdxG1k6IZBagZiYoDAsYp4YqNwmVsm5sLrZ9QVSf7EcH/y
qX8butZesiMd7xm7RROlrIImh7fb36N3zsoRiUWZDo1Al3IRkmZyVA==
=tdut
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10feb19' of git://git.denx.de/u-boot-dm
Samsung sound patches (applied for Samsung maintainer)
Common sound support
buildman environment support
of-platdata documentation improvements
Use regulator_set_enable_if_allowed() api instead of regulator_set_enable()
while enabling io regulators. This way the driver doesn't see an error
when disabling an always-on regulator and when enabling is not supported.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that these boards use driver model we can drop the old code. At
present s5p_mmc_init() is still used by goni and smdkv310 so cannot be
removed unless we remove those boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Errata i929 in certain OMAP5/DRA7XX/AM57XX silicon revisions
(SPRZ426D - November 2014 - Revised February 2018 [1]) mentions
unexpected tuning pattern errors. A small failure band may be present
in the tuning range which may be missed by the current algorithm.
Furthermore, the failure bands vary with temperature leading to
different optimum tuning values for different temperatures.
As suggested in the related Application Report (SPRACA9B - October 2017
- Revised July 2018 [2]), tuning should be done in two stages.
In stage 1, assign the optimum ratio in the maximum pass window for the
current temperature. In stage 2, if the chosen value is close to the
small failure band, move away from it in the appropriate direction.
References:
[1] http://www.ti.com/lit/pdf/sprz426
[2] http://www.ti.com/lit/pdf/SPRACA9
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
When using CMD6 to switch eMMC card timing from HS200/HS400 to HS/legacy,
do not poll for the completion status using CMD13, but rather wait 50mS.
Once the card receives the CMD6 and starts executing it, the bus is in
undefined state until both the card finishes executing the command and
until the controller switches the bus to matching timing configuration.
During this time, it is not possible to transport any commands or data
across the bus, which includes the CMD13.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
The internal DMAC asserts DMA transfer end bit too early on older
version of the TMIO IPs which use bit 17 for DTRAEND. Add 1uS
delay after the completion of DMA transfer and before invalidating
the cache to let the DMAC fully complete the transfer. Otherwise,
it could happen that the last few bytes of a transferred data are
not available.
A test case to trigger this behavior is the following command, ran
on the U-Boot command line, with Sandisk 16 GiB UHS-I card inserted
into SDHI slot 0 and with first partition being of type FAT:
=> while true ; do mmc rescan ; fstype mmc 0:1 ; done
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Different versions of the SDHI core use either bit 17 or bit 20 for the
DTRAEND indication, which can differ even between SoC revisions. Make
the DTRAEND bit position part of the driver private data, so that the
probe function can set this accordingly. Set this to 20 on Socionext
SoCs and either 17 or 20 on Renesas SoCs, depending on the SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
If a board DT describes a cd-gpios property, but also marks the storage
as non-removable, we must ignore the GPIO (as Linux does).
Teach the DM_MMC part of the Allwinner MMC driver about the
non-removable DT property, to fix DM_MMC access on the SoPine and
Pine64-LTS board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Now that we have the gate clocks and the reset gates in our new
Allwinner clock driver, let's make use of them in the MMC driver, when
DM_MMC is defined.
We treat the reset device as optional now, as the older SoCs don't
implement it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
A80 gates clock already be part of CLK framework, so just
add mod_clk offset with A80 compatible string.
Cc: Rask Ingemann Lambertsen <rask@formelder.dk>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Unlike other Allwinner SoC's, H6 uses a different MMC mod clock offset.
Connect that with the respective compatible string.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Add MMC compatible strings for A83T, A64, H5.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
This patch has been tested on the mcf54415-based stmark2
board. The eSDHC driver works reliably using DMA mode.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
It is not possible to link the SPL image when CONFIG_GPIO is enabled
but CONFIG_SPL_GPIO is not. Use the IS_ENABLED macro instead to
correctly check whether CONFIG_{SPL_}GPIO is enabled.
This commit fixes the following errors:
* undefined reference to `dm_gpio_get_value
* undefined reference to `gpio_request_by_name'
Signed-off-by: Fabien Parent <fparent@baylibre.com>
[trini: Move guard to fix warning in msdc_ops_get_wp()]
Signed-off-by: Tom Rini <trini@konsulko.com>
The code is checking for incomplete read when it see the INT_XFER_COMPL
flag, but it forget to first check whether there is anything left in the
FIFO to copy to the RX buffer. This means that sometimes we will get
errors because of erroneous incomplete read operation.
This commit fixes the driver re-ordering the code so that we first
check for data inside the RX fifo and only after check the status
of the INT_XFER_COMPL flag.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
This variable was incorrectly added by:
"mmc: zynq_sdhci: Add support for SD3.0"
(sha1: d1f4e39d58)
which had nothing to do with MMC power sequence provider.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The bounce buffer is used by a few drivers (most of the MMC drivers)
to overcome limitations in their respective DMA implementation.
This moves the configuration to Kconfig and makes it user-selectable
(even though it will be a required feature to make those drivers
work): the expected usage is for drivers depending on this to 'select'
it unconditionally from their respective Kconfig (see follow-up
patches).
This commit includes a full migration using moveconfig.py to ensure
that each commit compiles. To ensure bisectability we update
dependencies of various drivers to now select BOUNCE_BUFFER when needed.
[trini: Squash all patches to ensure bisectability]
Signed-off-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Otavio Salvador <otavio@ossystems.com.br> [dw_mmc portion]
Reviewed-by: Fabio Estevam <festevam@gmail.com> [mxsmmc portion]
Reviewed-by: Simon Glass <sjg@chromium.org> [tegra portion]
Do not build write support, unless it's enabled.
In the SPL case, this change will typically remove
precious bytes (as write support is most often
not needed in SPL).
This is important on this platform, where the maximum
SPL size is 14 KiB.
With gcc v7.3, this change saves 144 bytes producing:
size spl/u-boot-spl
text data bss dec hex filename
9240 752 712 10704 29d0 spl/u-boot-spl
To make the code easier to compile-out and more
readable, a pair of read_data/write_data helpers are created.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Use CONFIG_IS_ENABLED(BLK) instead of CONFIG_BLK,
in order to fix the following build issues when
CONFIG_SPL_MMC_WRITE is selected:
drivers/mmc/mmc_write.c:69:7: error: conflicting types for 'mmc_berase'
ulong mmc_berase(struct udevice *dev, lbaint_t start, lbaint_t blkcnt)
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:39:7: note: previous declaration of 'mmc_berase' was here
ulong mmc_berase(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt);
^~~~~~~~~~
drivers/mmc/mmc_write.c:187:7: error: conflicting types for 'mmc_bwrite'
ulong mmc_bwrite(struct udevice *dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
In file included from drivers/mmc/mmc_write.c:15:0:
drivers/mmc/mmc_private.h:37:7: note: previous declaration of 'mmc_bwrite' was here
ulong mmc_bwrite(struct blk_desc *block_dev, lbaint_t start, lbaint_t blkcnt,
^~~~~~~~~~
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The mmc_select_mode_and_width() function can be called while the card
is in HS200/HS400 mode and can be used to downgrade the card to lower
mode, e.g. HS. This is used for example by mmc_boot_part_access_chk()
which cannot access the card in HS200/HS400 mode and which is in turn
called by saveenv if env is in the MMC.
In such case, forcing the card clock to legacy frequency cannot work.
Instead, the card must be switched to HS mode first, from which it can
then be reprogrammed as needed.
However, this procedure needs additional code changes, since the current
implementation checks whether the card correctly switched to HS mode in
mmc_set_card_speed(). The check only expects that the card will be going
to HS mode from lower modes, not from higher modes, hence add a parameter
which indicates that the HS200/HS400 to HS downgrade is happening. This
makes the code send the switch command first, reconfigure the controller
next and finally perform the EXT_CSD readback check. The last two steps
cannot be done in reverse order as the card is already in HS mode when
the clock are being switched on the controller side.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Convert HiSilicon HI6220 MMC driver based on DWMMC IP to driver
model.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Enable this on poplar]
Signed-off-by: Tom Rini <trini@konsulko.com>
The following hang is observed on a Hummingboard 2 MicroSOM
i2eX iMX6D - rev 1.3 with no eMMC populated on board:
U-Boot SPL 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
Trying to boot from MMC1
U-Boot 2018.11+gf6206f8587 (Nov 16 2018 - 00:56:34 +0000)
CPU: Freescale i.MX6D rev1.5 996 MHz (running at 792 MHz)
CPU: Extended Commercial temperature grade (-20C to 105C) at 33C
Reset cause: POR
Board: MX6 HummingBoard2
DRAM: 1 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment
No panel detected: default to HDMI
Display: HDMI (1024x768)
In: serial
Out: serial
Err: serial
---> hangs
which is caused by the following infinite loop inside esdhc_send_cmd_common()
while (!(esdhc_read32(®s->irqstat) & flags))
;
Instead of looping forever, provide an exit path so that a timeout
error can be propagated in the case irqstat does not report
any interrupts, which may happen when no eMMC is populated on
board.
Reported-by: Ricardo Salveti <rsalveti@rsalveti.net>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Ricardo Salveti <rsalveti@rsalveti.net>
Existing clock configure code has been followed based on the
legacy MMC dt node definitions and it cannot work with recent
dts(i) sync from Linux.
So, add clock configure code for Allwinner platforms which support
DM_MMC and eventually this will drop once CLK support is in Mainline.
Fixes: 3c92cca3cd ("ARM: dts: sun4i: Update A10 dts(i) files from Linux-v4.18-rc3")
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Priit Laes <plaes@plaes.org> # Gemei G9 A10 Tablet
Tested-by: Marek Kraus <gamelasterv2@gmail.com> # A10-OLinuXino-Lime
Commit d0851c8937 ("blk: Call part_init() in the post_probe() method")
removed the call to part_init() in mmc.c, as this is done by the DM_MMC
framework.
However Allwinner is (still) relying on a non-DM MMC driver, so we are
now missing the implicit partition init, leading to failing MMC accesses
due to the missing partition information.
Bring the call back just for non-DM MMC driver to fix this regression.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Soeren Moch <smoch@web.de>
Add driver for the JZ47xx MSC controller.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
According to SD Specifications Part 1 Physical Layer Simplified Specification
Version 6.00 August 29, 2018, section 4.3.10 (Switch Function Command) and
section 5.6 (SCR register), SD cards version 1.00 and 1.01 do not support the
SD CMD 6.
Currently, U-Boot will issue CMD 6 unconditionally in sd_set_card_speed()
while configuring the bus for selected frequency. This will make SD cards
version 1.00 and 1.01 time out and thus fail detection altogether.
Fix this by not sending CMD 6 on such cards. Tested on Matsushita Electric
Industrial Co., Ltd. Japan RP-SD008B / Victor 8MB SD card, CU-SD008, which
is correctly detected with this patch as:
Device: sd@ee160000
Manufacturer ID: 1
OEM: 5041
Name: S008B
Bus Speed: 25000000
Mode : SD Legacy
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 6.5 MiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add support for the HS400 mode to SDHI driver. This uses the up-tune
mechanism from already supported HS200 tuning.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Move the tap_pos variable, which is the HS200/HS400/SDR104 calibration
offset, into private data, so it can be passed around. This is done in
preparation for the HS400 mode, which needs to adjust this value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Filter out HS400 support on SoCs where HS400 is not supported yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Reorder the tmio_sd_set_clk_rate() function such that it handles all
of the clock requiests correctly. Specifically, before this patch,
clock request with (mmc->clock == 0 && mmc->clk_disable) could leave
the clock enabled, as the function would exit on if (!mmc->clock)
condition on top and will not handle the mmc->clk_disable at all.
Rather than band-aid fixing just that particular problem, reorder
the entire function to make it easier to understand and verify that
all the cases are covered. The function has three sections now:
First, if mmc->clock != 0, we calculate divider for the SD block.
Second, if mmc->clock != 0 and SD block clock are enabled and
current divider is not equal to the new divider, then
stop the clock and update the divider.
Third, if mmc->clk_disable is set, disable the clock, otherwise
enable the clock. This happens independently of divider
update now.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a feature where it can automatically disable clock output
when the bus is not in use. While this is useful, it also interferes with
switching the bus to 1.8V and other background tasks of the SD/MMC cards,
which require clock to be enabled.
This patch respects the mmc->clk_disable and only disables the clock when
the MMC core requests it. Otherwise the clock are continuously generated
on the bus.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The TMIO core has a quirk where divider == 1 must not be set in DDR modes.
Handle this by setting divider to 2, as suggested in the documentation.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Switch the driver to using clk_get_rate()/clk_set_rate() instead of
caching the mclk frequency in it's private data. This is required on
the SDHI variant of the controller, where the upstream mclk need to
be adjusted when using UHS modes.
Platforms which do not support clock framework or do not support it
in eg. SPL default to 100 MHz clock.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
---
V2: - Fix build on certain platforms using SPL without clock framework
V3: - Turn clk_get_rate into a callback and fill it as needed on both
renesas and socionext platforms
Add HS400 properties parsing support to mmc_of_parse().
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Using new mode improves stability of eMMC and SD cards. Without
it SPL fails to load u-boot from SD on Pinebook.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Reviewed-by: Jagan Teki <jagan@openedev.com>
Comment in Linux driver says that clock needs to be doubled only
if we use DDR modes, moreover divider has to be set accordingly.
U-boot driver doesn't declare support for any DDR modes and doesn't
set internal clock divider in CLKCR, so it doubles clock
unconditionally when new mode is used.
Some cards can't handle that and as result SPL fails to load u-boot.
Fixes: de9b1771c3 ("mmc: sunxi: Support new mode")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
Allwinner A64 has new mode but doesn't have a mode switch in CCM,
and CCM_MMC_CTRL_MODE_SEL_NEW is not defined, so compilation fails
if MMC_SUNXI_HAS_NEW_MODE is enabled
Introduce new MMC_SUNXI_HAS_MODE_SWITCH option to be able to ifdef usage
of CCM_MMC_CTRL_MODE_SEL_NEW
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: update commit message]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # Amarula A64-Relic
When a driver declares DM_FLAG_PRE_RELOC flag, it wishes to be
bound before relocation. However due to a bug in the DM core,
the flag only takes effect when devices are statically declared
via U_BOOT_DEVICE(). This bug has been fixed recently by commit
"dm: core: Respect drivers with the DM_FLAG_PRE_RELOC flag in
lists_bind_fdt()", but with the fix, it has a side effect that
all existing drivers that declared DM_FLAG_PRE_RELOC flag will
be bound before relocation now. This may expose potential boot
failure on some boards due to insufficient memory during the
pre-relocation stage.
To mitigate this potential impact, the following changes are
implemented:
- Remove DM_FLAG_PRE_RELOC flag in the driver, if the driver
only supports configuration from device tree (OF_CONTROL)
- Keep DM_FLAG_PRE_RELOC flag in the driver only if the device
is statically declared via U_BOOT_DEVICE()
- Surround DM_FLAG_PRE_RELOC flag with OF_CONTROL check, for
drivers that support both statically declared devices and
configuration from device tree
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
A64 and H6 support automatic delay calibration and Linux driver uses it
instead of hardcoded delays. Add support for it to u-boot driver.
Fixes eMMC instability on Pinebook
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Cc: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds check for command response CRC failure. The driver
is currently ignoring CRC check failure on command resposes which
have CRC atteched to it, which can be potentially dangerous. Even
more grueling problem happens when the command response is followed
by data transfer though, as in that case, the dwmci_data_transfer()
function will spin until it reaches the 240s timeout.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
It is perfectly fine to write th DTCNTL TAP count and enable the
SCC sampling clock operation in the same write.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
When the bus switches to 1.8V mode of operation, it is necessary to
verify that the card correctly initiated and completed the voltage
switch. This is done by reading out the state of DATA0 line.
This patch implement support for reading out the state of the DATA0
line, so the MMC core code can correctly switch to 1.8V mode.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Make sure to clear HS400 configuration when resetting the SCC block.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Add check to avoid touching the SCC tuning registers in case the IP
doesn't support them or if the support isn't in place yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Preinitialize the SD card signals regulator to 3.3V, which is the
default post-reset setting, to be sure the regulator is set to a
valid value.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Configure the clock settings before reconfiguring any other IO settings.
This is required when the clock must be stopped before changing eg. the
pin configuration or any of the other properties of the bus. Running the
clock configuration first allows the MMC core to do just that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
In case the controller performs card tuning, that is, sends MMC
command 19 or 21, silence possible CRC error warning prints. The
warnings are bound to happen, since the tuning will fail for some
settings while searching for the optimal configuration of the bus
and that is perfectly OK.
This patch passes around the MMC command structure and adds check
into tmio_sd_check_error() to avoid printing CRC error warning
when the tuning happens.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Properly handle return values and abort operations when they are
non-zero. This is a minor improvement, which fixes two remaining
unchecked return values.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The SD UHS SDR12, SDR25, SDR50, SDR104, DDR50 and MMC HS200, HS400
modes all use 1.8V signaling, while all the legacy modes use 3.3V
signaling. While there are extra modes which use 1.2V signaling,
the existing hardware does not support those.
Simplify the pinmux such that 3.3V signaling implies legacy mode
pinmux and the rest implies UHS mode pinmux. This prevents the
massive case statement from growing further. Moreover, it fixes
an edge case where during SD 1.8V switch, the bus mode is still
set to default while the signaling is already set to 1.8V, which
results in an attempt to communicate with a 1.8V card using pins
in 3.3V mode and thus communication failure.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
When CONIFG_CLK is enabled, use uclass clk api to handle
the clock.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Add CONFIG_ARCH_IMX8 to use the 64bits support in usdhc driver.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Xilinx is introducing Versal, an adaptive compute acceleration platform
(ACAP), built on 7nm FinFET process technology. Versal ACAPs combine
Scalar Processing Engines, Adaptable Hardware Engines, and Intelligent
Engines with leading-edge memory and interfacing technologies to deliver
powerful heterogeneous acceleration for any application. The Versal AI
Core series has five devices, offering 128 to 400 AI Engines. The series
includes dual-core Arm Cortex™-A72 application processors, dual-core Arm
Cortex-R5 real-time processors, 256KB of on-chip memory with ECC, more
than 1,900 DSP engines optimized for high-precision floating point with
low latency.
The patch is adding necessary infrastructure in place without enabling
platform which is done in separate patch.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The internal DMAC on Gen3 is 32bit only, limit the DMA address
range to 32bit.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Pass the entire source data pointer to tmio_sd_addr_is_dmaable()
so we don't have to apply casts throughout the code.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adds mmc_rpmb_route_frames() to route RPMB data frames from/to an
external entity.
Tested-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The rk3188 works nicely with the rockchip mmc driver, so we just need
to add the different compatible for it - as used in the Linux kernel.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
While trying to enable the dw_mmc on rk3188 I managed to confuse
and hang the dw_mmc controller into not delivering further data.
The fifo state never became ready and the driver was iterating in
the while loop reading 0-byte packets forever.
So inspired by how other implementations handle this, check the fifo-
state beforhand and add a timeout to catch any glaring fifo issues
without hanging uboot altogether.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>
The MMC card detect pin is connected to gpio127 on omap3_logic.
When setting up the pbias register for MMC, let's also enable
gpio_127 for the card detect. As part of the package deal,
gpio_126 and gpio_129 are also enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>