The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_request to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_dev_*_ep to reflect this.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_phy to struct dwc2_usbotg_phy
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
Most of the functions are local to the s3c_udc driver, remove them
from the s3c_udc.h header to stop those bits from propagating all
over the place. Instead, move all the private stuff into new private
s3c_udc_otg_priv.h header.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_usbotg_reg to struct dwc2_usbotg_reg
to make things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
The driver is actually for the Designware DWC2 controller.
This patch renames struct s3c_udc to struct dwc2_udc to make
things more obvious and clear.
Signed-off-by: Marek Vasut <marex@denx.de>
We don't disable unused FM1-DTSEC1 MAC node in FMAN v2 since it is
used by MDIO. For FMAN v3, MDIO uses dedicated controller, so we
can disable unused FM1-DTSEC1 MAC node to avoid being probed in
Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
[York Sun: revised commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
Remove verbose message for FMan port.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
[York Sun: Added commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
The MC version numbers provide no meaningful information
about binary interface compatibility, so remove the
check which refuses to start the MC unless a specific
version is found.
Version checking is supposed to be done at the individual
object level, and individual drivers are responsible
for their own version checking.
Signed-off-by: Stuart Yoder <stuart.yoder@freescale.com>
Acked-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For Setting and clearing the bits in SEC Block registers
sec_clrbits32() and sec_setbits32() are used which work as
per endianness of CAAM block.
So these must be used with SEC register address as argument.
If the value is read in a local variable, then the functions
will not behave correctly where endianness of CAAM and core is
different.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
CC: Alex Porosanu <alexandru.porosanu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When reading a large blob. e.g. a linux kernel (several MiBs) a watchdog
timeout might occur meanwhile. So pet the watchdog while operating on
the flash.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As the errata A008336 and A008514 do not apply to all LS series SoCs
(such as LS1021A, LS1043A) we move them to an soc specific file
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With gcc-5.x we get a warning about the ambiguity of BUG_ON(!a != b) and
becomes BUG_ON((!a) != b). In this case reading of the function leads to
us wanting to rewrite this as BUG_ON(a != b).
Cc: Prabhakar Kushwaha <prabhakar@freescale.com>
Cc: Geoff Thorpe <Geoff.Thorpe@freescale.com>
Cc: Haiying Wang <Haiying.Wang@freescale.com>
Cc: Roy Pledge <Roy.Pledge@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DDR errata-A008378 applies to LS1021-20-22A-R1.0, T1023-R1.0,
T1024-R1.0, T1040-42-20-22-R1.0/R1.1, it has been fixed on
LS102x Rev2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case four chip-selects are all active, the turnaround times need to
increase to avoid overlapping under heavy load.
Signed-off-by: York Sun <yorksun@freescale.com>
The workaround requires different setting for range 1 vs 2.
Also adjust timeout value for waiting for controller to be idle.
Signed-off-by: York Sun <yorksun@freescale.com>
There is no sprintf implementation in tiny-printf, so don't try to use
it when tiny-printf if used.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Add xlnx,xps-spi-2.00.a/b which is compatible string
listed in the Linux kernel.
Remove origin one which has no real background.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since all spi-flash core operations are moved into
sf_ops.c then it's better to renamed as spi-flash.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Used static for file-scope functions in sf_probe.c
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Since spi_slave is a spi pointer in spi_flash{} then assign
spi_slave{} pointer to flash->spi and remove spi_slave
pointer argument to
- spi_flash_probe_slave
- spi_flash_scan
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
For assigning read_bar commands in spansion case, break
is missing this patch add that break.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
SST parts added on sf_params.c supports both SST_WR which consits
of both BP and WP and there is a spi controller ich which supports
only BP so the relevent _write hook set based on "slave->op_mode_tx"
hence there is no respective change required from flash side hance
removed these.
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Removed unneeded header includes in sf_ops and sf_probe
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Using macro's for flash power up read-only access code
leads wrong behaviour hence use idcode0 for runtime
detection, hence the flash which require this functionality
gets detected at runtime.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Most of the register access function are static,
so used simple name to represent each.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
This patch removes unneeded ifdef and fixed accordingly.
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Use static for file-scope functions and removed
them from header files.
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Jagan Teki <jteki@openedev.com>
- Move bar read code below the bar write hance both
at once place, hence it easy for #ifdef macro only
once and readable.
- Move read_cmd_array at top
Tested-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
read_id code is related to spi_flash stuff
hence moved to sf_ops.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Intension is that sf_ops should deals all spi_flash
related stuff and sf_probe (which should renamed future)
should be an interface layer for spi_flash versus spi drivers.
sf_ops => spi_flash interface
sf_probe => interface layer vs spi_flash(sf_probe) to spi drivers
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Rename spi_flash_validate_params to spi_flash_scan
as this code not only deals with params setup but
also configure all spi_flash attributes.
And also moved all flash related code into
spi_flash_scan for future functionality addition.
Tested-by: Jagan Teki <jteki@openedev.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Extend compatible list table for cdns,spi-r1p6 compatible string.
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
SPI_3WIRE is spi mode not spi flags, so this patch fixed
the spi-3wire checking throgh mode instead of flags.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
spi-3wire is used when SI/SO signals shared so get
the same from dts node and assign to mode on slave
plat->mode.
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jagan Teki <jteki@openedev.com>
Fix incorrect comment alignments.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a remark about SPL to this Kconfig option. Otherwise its identitcal
to the non-SPL version, which is confusing.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
AXP818 is rsb based PMIC and used on Allwinner A83T H8 Homlet dev board.
It's registers are different and calculating reg config is different than
that of earlier axp power ICs.
DCDC1, DCDC2, DCDC3 and DCDC5 is implemented at the moment.
all other voltages can be added subsequently.
AXP datasheet is uploaded to wiki:
http://linux-sunxi.org/File:AXP818_datasheet_Revision1.0.pdf
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
These are currently dead codes. Until we have complete ACPI support,
we don't know if it works or not. Remove to avoid confusion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Right now i8254_init() is called from timer_init() in the tsc timer
driver. But actually i8254 and tsc are completely different things.
Since tsc timer has been converted to driver model, we should find
a new place that is appropriate for U-Boot to call i8254_init(),
which is now x86_cpu_init_f().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This option is needed for all SoCs which have nodes on bus. Without
enabling this drivers are not found and probed.
Issue was found on Zynq MMC probe.
Enable this option by default.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
debug_uart.h is included twice.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove this c&p error from s5p driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Calculate the minimum sd clock based on max clock. This will
be done by add_sdhci() if we pass minimum clock as zero.
It also does based on SD host contoller version.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Do not set interface via configs. Read information from DT.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function was used for OF init before DM.
Remove this function as the part of move to DM.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Enable access to MDIO before zynq_gem_init is called.
It enables read information about phy earlier.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Move phy init code out of zynq_gem_init. DM drivers are normally calling
this code from probe function.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Next step to move driver to driver model. Do not use eth_device
structure. Use private structure instead.
Add iobase to private structure to store gem iobase.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add return value for phy detection algorithm to stop init function when
phy is not found.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Convert the SoCFPGA shim for registering the DWMMC driver to DM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This patch removes unsued function usb_phy_reset, rather common function
dwc3_phy_reset is used.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
As per dwc3 databook, delay is required before taking the core out of reset.
This delay is required so that the PHY are stable, and then we can take core
out of reset.
Reference is taken from linux dwc3 code, file: drivers/usb/dwc3/core.c.
Signed-off-by: Sriram Dash <sriram.dash@freescale.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@freescale.com>
This driver is meant to be used with any EHCI-compatible host
controller in case if there's no need for platform-specific
glue such as setup of controller or PHY's power mode via
GPIOs etc.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
The DM entry should be unique, otherwise it will collide with other
drivers. Fix this by assigning the driver a more unique name than
usb_ehci.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Ian Campbell <ijc@hellion.org.uk>
Cc: Simon Glass <sjg@chromium.org>
The driver does "return 0" in function with void type.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
fix the following build warnings:
drivers/usb/dwc3/core.c: In function ‘dwc3_uboot_init’:
drivers/usb/dwc3/core.c:625:6: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
mem = devm_kzalloc(dev, sizeof(*dwc) + DWC3_ALIGN_MASK, GFP_KERNEL);
^
drivers/usb/dwc3/dwc3-omap.c: In function ‘dwc3_omap_uboot_init’:
drivers/usb/dwc3/dwc3-omap.c:380:7: warning: ‘dev’ is used uninitialized in this function [-Wuninitialized]
omap = devm_kzalloc(dev, sizeof(*omap), GFP_KERNEL);
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix the following build break:
drivers/usb/host/xhci-omap.c:35:5: error: ‘board_usb_init’ aliased to external symbol ‘__board_usb_init’
int board_usb_init(int index, enum usb_init_type init)
^
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix erase and write error code, which should be "protected".
From the "Embedded Peripherals IP User Guide" of Altera,
The "Illegal write" flag indicates that a write instruction is
targeting a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled a write instruction.
The "Illegal erase" flag indicates that an erase instruction has
been set to a protected sector on the flash memory. This bit is
set to indicate that the IP has cancelled the erase instruction.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add lock() and unlock() mtd ops to altera_qspi.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Chin Liang See <clsee@altera.com>
Reviewed-by: Marek Vasut <marex@denx.de>
For platforms that don't use device tree in SPL the only way to mark this
driver as 'required by relocation' is with the DM_FLAG_PRE_RELOC flag. Add
this to ensure that the driver is bound.
Fixes: fde7e18938 ("dm: tegra: pci: Move CONFIG_PCI_TEGRA to Kconfig")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Neither uc_pdata->name nor check_name are supposed to be NULL in
_rproc_name_is_unique(). if uc_pdata->name is NULL, we are not
intialized yet, however if check_data is NULL, we do not have
proper data. Further, if either were NULL, strlen will crap out
while attempting to derefence NULL.
Instead, just check if either of these are NULL and bail out.
This should also fix the following coverity scan warnings:
*** CID 132281: Null pointer dereferences (FORWARD_NULL)
/drivers/remoteproc/rproc-uclass.c: 73 in _rproc_name_is_unique()
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Change reg-shift property default to zero. When the integer property
is missing, it should be taken as zero. This is consistent to Linux
drivers/tty/serial/of_serial.c.
The x86 and most powerpc use reg-shift of 0. Most others use reg-shift
of 2. While reg-shift of 1 is rarely used.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Simon Glass <sjg@chromium.org>
We now use the generic delay method which specifies the timeout as
microseconds instead of ticks.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
rk3036 mmc do not have internal dma, so we use fifo mode when read
and write data, we get the fifo mode and fifo depth property from
dts, pass to dw_mmc driver.
Signed-off-by: Lin Huang <hl@rock-chips.com>
emmc and sdcard have different register address, use non-removeable property
to distinguish them.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
some soc(rk3036 etc) use dw_mmc but do not have internal dma,
so we implement fifo mode to read and write data.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
the data transfer seem to long in the dwmci_send_cmd function,
so move this block as a separate funciton.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add a driver for setting up and modifying the various PLLs, peripheral
clocks and mmc clocks on RK3036
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add SPL Kconfig for REGMAP and SYSCON, so REGMAP and SYSCON can
remove from SPL stage.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
We eventually need to drop the compatibility functions for driver model. As
a first step, create a configuration option to enable them and hide them
when the option is disabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some functions will be used by driver model and legacy PCI code. To avoid
duplication, put these in a separate, shared file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file should not be used with driver model as it has lots of legacy/
compatibility functions. Rename it to make this clear.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Adjust the Tegra PCI driver to support driver model and move all boards over
at the same time. This can make use of some generic driver model code, such
as the range-decoding logic.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
This function looks up the controller and returns a pointer to each region
type.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
A PCI bus may be a bridge device where the controller is the bridge's
parent. Add a function to return the controller device, given a PCI device.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Provide a few functions to support using 32-bit access to emulate 8- and
16-bit access.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
At present we add a new resource entry for every range entry. But some range
entries refer to configuration regions. To make this work, avoid adding two
regions of the same type. The later ranges will overwrite the earlier
(configuration) ones.
There does not seem to be a way to distinguish the configuration ranges
other than by ordering (as per the device tree binding).
We could perhaps instead just store one region of each type in a simple
array. Once we are sure that we don't need to support multiple regions, we
could change this. It would be easier to do it when all drivers are
converted to use driver model for PCI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
SDRAM doesn't always start at 0. Adjust the region mapping so that it works
on platforms where SDRAM is somewhere else.
This needs testing on other platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
To group all dm timer drivers together, move tsc timer to
drivers/timer directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are timers with a 64-bit counter value but current timer
uclass driver assumes a 32-bit one. Modify timer_get_count()
to ask timer driver to always return a 64-bit counter value,
and provide an inline helper function timer_conv_64() to handle
the 32-bit/64-bit conversion automatically.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use device tree to pass the clock frequency of the timer
instead of hardcoded in the driver codes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since we have timer uclass to get clock frequency for us, remove
the custom version in the altera timer driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
Every timer device needs to have a valid clock frequency and it
can be specified in the device tree. Use pre_probe() to get this
in the timer uclass driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Simon Glass <sjg@chromium.org>
This changes 'Timer' to 'timer' at several places.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
The phy can share driver with other aquantia PHYs, so we only
add PHY ID.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: York Sun <yorksun@freescale.com>
BIST test code has a typo, resulting the binding registers not
maintained as expected. This typo results BIST runs twice on
the covered memory.
Signed-off-by: York Sun <yorksun@freescale.com>
Reported-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Freescale LSCH3 platforms use two DDR controlers interleaving mode out of
reset. It can be configured to disable one controller. To support this
operation, the driver needs to detect and skip the disabled controller.
Signed-off-by: York Sun <yorksun@freescale.com>
The endian and base address of PEX LUT register region is different
between Chassis 2 and Chassis 3, so move the base address definition
to chassis specific header file and add pex_lut_* functions to access
LUT register.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
MC 0.7.1.2 enforces limitation i.e.: "Packets may be corrupted
in several combinations of buffer size and frame offsets.
Workaround: Use buffers that are of size that is a multiple of 256, and
frame offset that is a multiple of 256"
Updating the DPNI Eth driver to comply with the restriction.
Signed-off-by: Bogdan Hamciuc <bogdan.hamciuc@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add following debug information in the driver
- Get various DPNI counter values
- Get link status of DPNI objects
- Get information of both ends of connection (DPMAC - DPNI)
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As per current implementation of DPAA2 ethernet driver DPNI is used as
net device. DPNI is tangible objects can be multiple connected to same physical lane.
Use DPMAC as net device where it represents physical lane.
Below modification done in driver
- Use global DPNI object
- Connect DPMAC to DPNI
- Create and destroy DPMAC
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's DPAA2 ethernet driver depends upon the static DPL for the
DPRC, DPNI, DPBP, DPIO objects.
Instead of static objects, Create DPNI, DPBP, DPIO objects at run-time.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
dpni_create API take takes more time as comapred to existing supported
APIs of MC Flib.
So increase MC command timeout.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC represents physical line on the board. This physical
line eventually asscociate with on-board PHY.
So Add an api to return linked PHY ID of DPMAC object.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
DPMAC object of Management complex controls Physical MAC and MDIO controller.
It provides APIs for MDIO and link state updates. It also provides APIs for
PHY/link configuration.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current Management Complex Flibs does not support APIs for adding and
destroying the objects.
Add APIs to create and destroy objects for DPBP, DPIO, DPNI and DPRC.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Current implementation only consider SGMIIs for dpmac initialization.
XFI serdes protocols also uses dpmac.
Also, fix lane protocol parsing logic to consider both XFIs and SGMIIs.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
socfpga_dw_mmc driver will obtain the drvsel and
smplsel value from device tree instead of definition
in config header file.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
We need to access reg stp_rep9, but not stp_rep[(9 - 1) / 2].
If using "__raw_writel(0, DI_STP_REP(disp, 9))", this will exceeds
the size of stp_rep array.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Liu Ying <Ying.Liu@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Simplify if/else code, since if channel equals to MEM_BG_SYNC or
MEM_FG_SYNC, we have value 5 for 'dc_chan'.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The address range check may overflow if the memory region is located at
the top of the 32-bit address space. This can e.g. be seen on TK1 if
using the E1000 gigabit Ethernet driver where start and size are both
0x80000000 leading to the following messages:
Apalis TK1 # tftpboot $loadaddr test_file
Using e1000#0 device
TFTP from server 192.168.10.1; our IP address is 192.168.10.2
Filename 'test_file'.
Load address: 0x80408000
Loading: pci_hose_phys_to_bus: invalid physical address
This patch fixes this by changing the order of the addition vs.
subtraction in the range check just like already done in
__pci_hose_bus_to_phys().
Reported-by: Ivan Mercier <ivan.mercier@nexvision.fr>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
compiling U-Boot for avr32 boards shows since
commit 3d1957f0ea "dm: i2c: Add support for multiplexed I2C buses"
this warning:
Building current source for 4 boards (4 threads, 8 jobs per thread)
avr32: + atstk1002
+(atstk1002) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + grasshopper
+(grasshopper) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100
+(atngw100) drivers/i2c/built-in.o: warning: input is not relaxable
avr32: + atngw100mkii
+(atngw100mkii) drivers/i2c/built-in.o: warning: input is not relaxable
0 4 0 /4 0:00:16 : atngw100mkii
Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
