Update device tree in preparation of further driver model migration:
Ethernet FEC, ESDHC aka MMC/SD card, I2C, NFC aka NAND flash controller,
USBH_PEN GPIO regulator.
Add iomux resp. pinctrl entries to be removed from proprietary platform
data: DSPI, ESDHC, FEC, I2C, NFC, UART, USBH_PEN GPIO.
Introduce a U-Boot specific device tree with some required
u-boot,dm-pre-reloc properties: soc, aips0, pinctrl_ddr and uart0 incl.
pinctrl.
While at it also update the MAINTAINERS file.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Spotted two missing spaces in comments.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
... as preparation for additional driver model coonversions.
We use CONFIG_OF_EMBED here to keep u-boot.imx as final binary name. So we
maintain compatibility with the original TBS u-boot and available HOWTOs
for u-boot updates.
Signed-off-by: Soeren Moch <smoch@web.de>
The PMIC on the Colibri iMX6 may have ECC errors in fuses that will
prevent correct settings. Up to one bit error per fuse bank can be
reported and corrected by the ECC logic. Two bit errors can only be
reported.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
RGMII_RD1 pin (active high, GPIO6_IO27) is triggered on reboot during
the SPL phase. This asserts (active low) nReset_Out from the PMIC.
Only V1.1 and later Colibri iMX6 modules implement this in hw. Previous
versions do not use this pin, so it is safe to leave it enabled at all
times.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Make sure CMA memory is not greater than 50% of available physical
memory.
Allow user to change the CMA memory via 'cma-size' U-Boot environment
variable.
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before Image 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achived by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Colibri iMX6 V1.1 HW can use the PMIC GEN3 to power the NVCC_SD1.
Change the settings fused into the PMIC's OTP to powerup with
GEN3 set to output 3.3V.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In the linux device tree we use 40Ohm drive strenght. So use the same
value in U-Boot.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Print also for Colibri iMX6 512MB IT with 64-bit RAM bus.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight, MMC/SD
card detect and USB power enable GPIOs and also enable SION bit in pin
muxing for auxiliary, backlight and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes, add
some comments clarifying ifdef scope and do some white-space clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The PMIC on Apalis iMX6 may have ECC errors in fuses that will prevent
correct settings. Up to one bit error per fuse bank may be reported and
corrected by the ECC logic. Two bit errors can only be reported.
Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.
Before BSP 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achieved by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.
Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.
Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In the Linux device tree we use 40Ohm drive strength. So use the same
value in U-Boot.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This doesn't do anything anymore, probably never did.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.
While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
BK4 requires setup of 50MHz reference clock for its KSZ8081 PHY devices.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This code allows reusing the default u-boot as in the late board init, the
default envs are restored and proper recovery scripts executed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The "m4go" provides exactly the same functionality as the IMX generic
"bootaux" command. Remove it to not duplicate the code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As the I2C2 clock is now enabled in the generic clock code, we can remove
this code from a board file.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
- Misc dts files sync'ed with Linux version (Chris)
- Orion watchdog fix (Chris)
- kwbimage changed to also support Marvell bin_hdr binary (Chris)
- Add DM support to enable CONFIG_BLK for sata_mv (Stefan)
- Enable BLK on multiple platforms (Stefan)
- Misc minor fixes to AXP theadorable board (Stefan)
- Correct logic for DM_SCSI + unconverted drivers check (stefan)
- Misc changes to kirkwood to enable DM_USB here (Chris)
- Change ahci_mvebu to enable usage on A38x (Baruch)
- Update the kirkwood entry in git-mailrc (Baruch)
- Misc minor improvements (turris, documentation) (Baruch)
- Enhance sata_mv to support Kirkwood as well (Michael)
- Add wdt command (Michael)
- Add Marvell integrated CPUs (MSYS) support with DB-XC3-24G4XG
board support (Chris)
In Jaguar2 SoC family there are 3 different pcb. Each of this needs
to configure the phys in different ways. Therefore implement the
function board_phy_config and based on pcb configure them accordingly.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
QCA9563 is CPU used on AP152 board :
Clock speed : 750 MHz ,
Arch : Mips 74Kc,
Eth : SGMII interface,
MIMO config : 3 * 3 450M,
2 * USB 2.0,
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2:
- coding style cleanup
- remove ununsed flash chip in defconfig
- enable automatic icache / dcache size in defconfig
Changes for v3:
- add detailed information for qca956x in commit message
Changes for v4:
- remove pre-configured network settings in ap152.h
Changes for v5:
- coding style cleanup
In order to insure that hog GPIOs are configured early during
the boot process, force all pinctrl driver probing in board_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For DK1/DK2 boards, check if power supply provides enough current
to allow the board to boot correctly.
ADC@0 channel 18 and 19 are connected to USB type-C CC1 and CC2
signals. The table below shows the behavior for different range of
CC1 or CC2:
range | power supply | red led | console message
(Volts) | (Amps) | blinks |
--------------|--------------|---------|-----------------------------------
[2.10 - 1.23[ | 3 | NO | NO
[1.23 - 0.66[ | 1.5 | 3 times | WARNING 1.5A power supply detected
[0.66 - 0] | 0.5 | 2 times | WARNING 500mA power supply detected
If detected current is < 3A, red led is kept ON after blinking.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Alignment with STPMIC1 datasheet
s/MAIN_CONTROL_REG/MAIN_CR/g
s/MASK_RESET_BUCK/BUCKS_MRST_CR/g
s/MASK_RESET_LDOS/LDOS_MRST_CR/g
s/BUCKX_CTRL_REG/BUCKX_MAIN_CR/g
s/VREF_CTRL_REG/REFDDR_MAIN_CR/g
s/LDOX_CTRL_REG/LDOX_MAIN_CR/g
s/USB_CTRL_REG/BST_SW_CR/g
s/STPMIC1_NVM_USER_STATUS_REG/STPMIC1_NVM_SR/g
s/STPMIC1_NVM_USER_CONTROL_REG/STPMIC1_NVM_CR/g
and update all the associated defines.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Alignment with kernel driver name & binding
introduced by https://patchwork.kernel.org/cover/10761943/
to use the final marketing name = STPMIC1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Prepare file modification for kernel alignment and
rename driver to stpmic1.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Initialize the system configuration for basic boot
- update interconnect setting
- disable pull-down for boot pin
- enable High Speed Low Voltage Pad mode for SPI, SDMMC, ETH, QSPI
- activate I/O compensation
Done by SSBL = TF-A for trusted boot
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Clearly separate bootcmd for stm32mp1 board
(bootcmd_stm32mp) and preboot management.
That solve issue for fastboot continue command.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Set board name with the first dts compatible found in DT
code under CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
The result with DEVICE_TREE=stm32mp157c-ev1 is:
STM32MP> env print
board=stm32mp1
board_name=stm32mp157c-ev1
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Implement checkboard() function to display
- the boot chain used: basic or trusted
- the board compatible in device tree
- the board identifier and revision, saved in OTP59 for ST boards
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of trusted boot, using TF-A as first stage bootloader,
The boot sequence is
BootRom >=> TF-A.stm32 (clock & DDR) >=> U-Boot.stm32
The TF-A monitor provides secure monitor with support of SMC
- proprietary to manage secure devices (BSEC for example)
- PSCI for power
The same device tree is used for STMicroelectronics boards with
basic boot and with trusted boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Missed few mails from openedev, since most of the day I look at
amarulasolutions mail so update the same.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
When booting the am3517-evm, the following message appears:
SPL: Please implement spl_start_uboot() for your board
SPL: Direct Linux boot not active!
This patch implements spl_start_uboot to clear this message
and allow device to know if it should boot U-Boot or kernel.
Fixes: 1c6b6f383a ("ARM: am3517_evm: Enable Falcon Mode")
Signed-off-by: Adam Ford <aford173@gmail.com>
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Create a ft_board_setup() api that gets called as part of
DT fixup before jumping to kernel. In this ft_board_setup()
call fdt_fixup_msmc_ram that update msmc sram node.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the PCIe port specific link capabilities configuration
for Armada XP. The weak function board_sat_r_get() was used to return
a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This
is now changed with this patch to return a bit per PCIe port (4 bits
in this case, bit 0 for PCIe port 0, etc).
The theadorable board uses this new feature to configure PCIe port 0
as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards
using this function are not changed in the configuration and still
configure all ports as PCIe Gen2.
This patch also removes the parameter "pex_mode" from
board_serdes_cfg_get() as this parameter was not used in any of the
implementations.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Document build and install of U-Boot image on Clearfog with eMMC.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The check for the missing PEX switch can lead to an infinite loop, when
the PCIe device is not found. It is helpful to enable the user to break
out of this boot-loop, to enable booting to the prompt for test cases.
This patch adds a 3 second delay in the error case before rebooting.
The user can press Ctrl-C in this time to abort the boot-loop.
This patch also calls bootcount_inc() before rebooting in the error
case. This is needed to increment the bootcounter, since this function
is called earlier than the main bootcounter increment. Otherwise the
bootcounter will not be incremented in the error case at all.
Signed-off-by: Stefan Roese <sr@denx.de>
Enable the hardware watchdog to guard against system lock ups when
running in the SPL or U-Boot. Stop the watchdog just before booting so
that the OS can re-enable it if needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The generic wdt_start API expects to be called with the timeout in
milliseconds. Update the orion_wdt driver to accept a timeout in
milliseconds and use the clock rate specified in the dts to convert the
timeout to an appropriate value for the timer reload register.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
v2018.01 commit e23eb942ad ("ARM: rmobile: Stop using
rcar-common/common.c on Gen3") removed
board/renesas/rcar-common/common.c from the build chain with the
reasoning that calling arch_preboot_os() is no longer needed.
However, it left the arch_preboot_os() in place. Get rid of it.
This is done in preparation of resurrecting rcar-common/common.c.
NOTE: The three removed header includes (io.h, sys_proto.h, rcar-mstp.h)
are in direct relationship with the dropped arch_preboot_os() hook. The
other headers (common.h, rmobile.h) are going to be needed by pretty
much anything that is going to appear in the rcar common code. So, keep
the two in place.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Add defconfig and board specific adjustments for the R8A77965 M3N ULCB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcrEcDAAoJEB6zHgIOrC/I1dgH/3mHQNW8bqiNCJYcoVQdheHb
e06TqbWHNlOG/NilYybvdeF+LjeCqhX4PzyL/sdcyBf3D/tK4cVvHpZrQyjb2s6K
5IZSKJ+cZznmq6Hv7b//d30Azhx8bi8luxs60kkj+PF0xI1EyU3JteUqAs4Ooxd7
z+HdcRFuAaps6sy0+szB3fTw9HTGrhFvQuHasDGb2uahhpwGzu/P0RchIDksOdzH
3L4EOvgq8MZCiZ3ZtFWMWzQoCjcKf5Fuux41qar8gG/LrkWRfKG+LfWfZtTiTsjf
vC9bYWmdKtkSLFj1PWgLBfGxev5zwPUbqI2EP4OlagfNs3os5pVFCYV5NZ6ovdE=
=kMXf
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.07-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.07 cycle
