Since commit 067e0b9684 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.
Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.
This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Subsystems such as USB expect dma_map_single() and dma_unmap_single() to
do dcache flush/invalidate operations as required. For example, see
see drivers/usb/gadget/udc/udc-core.c::usb_gadget_map_request().
Currently drivers do this locally, (see drivers/usb/dwc3/ep0.c,
drivers/mtd/nand/raw/denali.c etc..)
Update arch specific dma_map_single() and dma_unmap_single() APIs to do
cache flush/invalidate operations, so that drivers need not implement
them locally.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Update the .dts file from the kernel, which carries much more nodes,
some of them we need to enable USB and Ethernet support for the board.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Sync the device tree files and device tree header files from upstream
Linux kernel, as of 2020-01-08. The commit synced to in the sunxi repo
98d25b0b266d Merge branch 'sunxi/dt-for-5.6' into sunxi/for-next
which is also part of next-20200108.
Changes brought in include:
- cleanup of pinmux node names
- addition of Security ID, MBUS, CSI, crypto engine, video codec,
pmu, and thermal sensor device nodes for both SoCs
- addition of deinterlacing engine device node on H3
- cleanup of RTC device node and addition of its clocks
- various board cleanups and improvements
- removal of pinmux node for GPIO lines
- cpufreq / DVFS
- HDMI output
- UART-based Bluetooth
- audio codec
- USB ports
- new boards
Most of the changes don't concern U-boot.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is only used on ARM devices so does not belong in the global
common header file. Move it to an ARM header.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions relate to setting up the device tree for booting the OS.
The fdt_support.h header file supports similar functions, so move these
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an init function so move it out of the common header. Avoid using
the typedef so that we don't have to include the global_data header file.
Also tidy up the function style in comments while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an arch-specific handoff header so that we can use the HANDOFF feature
on arm devices.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Exports the serdes configuration as an environment variable for LS gen 3
SoCs, so it can be used in u-boot command line. It should particularly
be useful for applying Linux DT overlays for the given serdes
configuration.
This code is called from arch_misc_init and not from the existing
serdes_init function because it depends on U-Boot environment being set
up.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LS1028A board code uses arch_misc_init to set up the board mux
on QDS. Move this code to misc_init_r. This is consistent with LS gen 2
and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS108x SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The arch_misc_init function is empty on LS2 SoCs/boards, remove it.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently LX2 board code uses arch_misc_init to set up the board mux on
RDB and QDS. Move this code to misc_init_r. This is consistent with LS
gen 2 and T series SoCs/boards.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add serdes protocol 0x7777, 0x9999, 0xb998, 0xbb56 to supported list.
These protocols are supported and functional but they trigger a warning
in U-Boot console at boot because they are not on this list.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
LS1088A has four personalities, LS1088A, LS1084A, LS1048A and LS1044A.
LS1044A, LS1048A are LS1088A personalities, which support only one
1x 10GE port.
MAC1 and MAC2 are associated with 1G SGMII, 2.5G SGMII, and XFI.
Disable MAC1 to have only one 1x 10GE port for LS1044A, LS1048A.
Signed-off-by: Pramod Kumar <pramod.kumar_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
These config entries are inside the menu block, which already
depends on ARCH_LS1021A:
menu "LS102xA architecture"
depends on ARCH_LS1021A
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Program register bit of SCFG_SNPCNFGCR_USBRDSNP and
SCFG_SNPCNFGCR_USBWRSNP to drive USB read/write
snoop signal on LS1012A.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm68360.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Set the kernel device-tree file (fdtfile environment variable) based on
run-time detection of the platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
