Write required information into the SSDT to describe the SD card
card-detect pin. Since the required GPIO properties are not present in
the device-tree binding, set them manually for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
As per the SD physical layer specification version 7.10, erase
command (CMD38) and stop transmission command (CMD12) will generate
R1b response.
R1b = R1 + busy signal
A non-zero value after the R1 response indicates card is ready for
next command.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Erase block start address (CMD32) and erase block end address (CMD33)
command will generate R1 response for mmc SPI mode.
R1 response is 1 byte long for mmc SPI, so assign 1 byte as a response
for this commands.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
Send status command (CMD13) will send R1 response under SD mode
but R2 response under SPI mode.
R2 response is 2 bytes long, so read 2 bytes for mmc SPI mode
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
The content of ssr is useful only for erase operations.
This saves erase time.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
R1 response is 1 byte long for mmc SPI commands as per the updated
physical layer specification version 7.10.
So correct the resp and resp_size for existing commands
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
When variable i will become 0, while(i--) loop breaks but variable i will
again decrement to -1 because of i-- and that's why below condition
"if (!i && (r != resp_match_value)" will never execute, So doing "i--"
inside of while() loop solves this problem.
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Tested-by: Bin Meng <bin.meng@windriver.com>
In commit commit d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
was changed 3.0V IO voltage to 3.3V but it was not done on all places in
omap_hsmmc driver. That commit broke eMMC support on Nokia N900.
This patch fixes that problematic commit and changes 3.0V to 3.3V on all
remaining places in omap_hsmmc driver.
Fixes: d2c05f50e1 ("mmc: omap_hsmmc: Set 3.3V for IO voltage")
Signed-off-by: Pali Rohár <pali@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Faiz Abbas <faiz_abbas@ti.com>
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl8InaQRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreazvAgAgqyvPY2o+BNHscrx9/6sEOHSAVty/D5t
SdaphzRezlJOWy9MC/ZyqyevZjogN7fgGNQVgh/I4BklIc/N5Omn68/+JWylSFVP
taJKiJD1IVSThTXGOMTxlDiTxY7NfVDUDjtFIpCDswBrnSJlX+2v/RsehUwVIrYn
NJwiRXd33IdS1vh1mqqNgwbZNBo+zGWn5LApq71vLSVkiQlmcpMG9FmYYRcg/AhG
3Xd2HB2ANcvb13fMMcwd3s4WPNYoiJvwjSHScNDUPEip7XeZNDiNeq4gC6d2Uw+J
zC3/vOCP3eRtAnr6syJ5QcGN/eeKwLtnTE+fOuOm6s5Y98po4iMykA==
=3fC5
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10jul20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
of-platdata: better phandle and compatible-string support
patman support for Python3 on Ubuntu 14.04
new checkpatch check to avoid #ifdefs
On build with 32 bit, there is a warning for int-to-pointer-cast.
Fix the int to pointer cast by using uintptr_t.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
In the current implementation, when dtoc parses a dtb to generate a struct
platdata it converts the information related to linked nodes as pointers
to struct platdata of destination nodes. By doing this, it makes
difficult to get pointer to udevices created based on these
information.
This patch extends dtoc to use struct driver_info when populating
information about linked nodes, which makes it easier to later get
the devices created. In this context, reimplement functions like
clk_get_by_index_platdata() which made use of the previous approach.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently when using OF_PLATDATA the binding between devices and drivers
is done trying to match the compatible string in the node with a driver
name. However, usually a single driver supports multiple compatible strings
which causes that only devices which its compatible string matches a
driver name get bound.
To overcome this issue, this patch adds the U_BOOT_DRIVER_ALIAS macro,
which generates no code at all, but allows an easy way to declare driver
name aliases. Thanks to this, dtoc could be improve to look for the driver
name based on its alias when it populates the U_BOOT_DEVICE entry.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When using OF_PLATDATA, the bind process between devices and drivers
is performed trying to match compatible string with driver names.
However driver names are not strictly defined, and also there are different
names used when declaring a driver with U_BOOT_DRIVER, the name of the
symbol used in the linker list and the used in the struct driver_info.
In order to make things a bit more clear, rename the drivers names. This
will also help for further OF_PLATDATA improvements, such as checking
for valid driver names.
Signed-off-by: Walter Lozano <walter.lozano@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a fix for sandbox of-platdata to avoid using an invalid ANSI colour:
Signed-off-by: Simon Glass <sjg@chromium.org>
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
-----BEGIN PGP SIGNATURE-----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=dnTK
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-06-29' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips into next
- net: pcnet: cleanup and add DM support
- Makefile: add rule to build an endian-swapped U-Boot image
used by MIPS Malta EL variants
- CI: add Qemu tests for MIPS Malta
Add missing space before a comment delimiter.
Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXvScEQAKCRDKSWXLKUoM
IeHUAJ9Z1shAlbILuHZKEpqQySLHdUVgBQCff8Nf+wi1rByTrwflKt14MtIsdFY=
=2Yuu
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2020.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2020.10
Versal:
- xspi bootmode fix
- Removing one clock from clk driver
- Align u-boot memory setting with OS by default
- Map TCM and OCM by default
ZynqMP:
- Minor DT improvements
- Reduce console buffer for mini configurations
- Add fix for AMS
- Add support for XDP platform
Zynq:
- Support for AES engine
- Enable bigger memory test by default
- Extend documentation for SD preparation
- Use different freq for Topic miami board
mmc:
- minor GD pointer removal
net:
- Support fixed-link cases by zynq gem
- Fix phy looking loop in axi enet driver
spi:
- Cleanup global macros for xilinx spi drivers
firmware:
- Add support for pmufw reloading
fpga:
- Improve error status reporting
common:
- Remove 4kB addition space for FDT allocation
SDHCI HISPD bits need to be configured based on desired mmc
timings mode and some HISPD quirks.
So, handle the HISPD bit based on the mmc computed selected
mode(timing parameter) rather than fixed mmc card clock
frequency.
Linux handle the HISPD similar like this in below commit but no
SDHCI_QUIRK_BROKEN_HISPD_MODE,
commit <501639bf2173> ("mmc: sdhci: fix SDHCI_QUIRK_NO_HISPD_BIT handling")
This eventually fixed the mmc write issue observed in
rk3399 sdhci controller.
Bug log for refernece,
=> gpt write mmc 0 $partitions
Writing GPT: mmc write failed
** Can't write to device 0 **
** Can't write to device 0 **
error!
Cc: Kever Yang <kever.yang@rock-chips.com>
Cc: Peng Fan <peng.fan@nxp.com>
Peng Fan: added back "ctrl &= ~SDHCI_CTRL_HISPD;" per Jaehoon's suggestion
Tested-by: Suniel Mahesh <sunil@amarulasolutions.com> # roc-rk3399-pc
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
According to eMMC specification v5.1 section 6.4.3, we should issue
CMD1 repeatedly in the idle state until the eMMC is ready even if
mmc_send_op_cond() send CMD1 with argument = 0. Otherwise some eMMC
devices seems to enter the inactive mode after mmc_complete_op_cond()
issued CMD0 when the eMMC device is busy.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
In current code, we add 1ms dealy after each tuning command for standard
tuning method. Adding this 1ms dealy is because USDHC default check the
CMD CRC and DATA line. If detect the CMD CRC, USDHC standard tuning
IC logic do not wait for the tuning data sending out by the card, trigger
the buffer read ready interrupt immediately, and step to next cycle. So
when next time the new tuning command send out by USDHC, card may still
not send out the tuning data of the upper command，then some eMMC cards
may stuck, can't response to any command, block the whole tuning procedure.
If do not check the CMD CRC for tuning, then do not has this issue. USDHC
will wait for the tuning data of each tuning command and check them. If the
tuning data pass the check, it also means the CMD line also okay for tuning.
So this patch disable the CMD CRC check for tuning, save some time for the
whole tuning procedure.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
We only call the function omap_hsmmc_get_cfg in the case of OMAP34XX or
when we have to iodelay recalibration. Add guards for these checks as
clang will otherwise warn.
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Unsupported voltage on voltage switch is not an error, do not
print error message in such a case. This happens e.g. if the
eMMC is already in 1V8 mode or when testing 1V2 mode operation
on systems which only do 3V3/1V8 switching.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The 3V3/1V8 switching could never have worked on any of the iMXes
ever since 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200"),
because that commit uses priv->vqmmc_dev when switching voltages on
mode switch, while local vqmmc_dev in probe to store the regulator
pointer. Those are two different variables with the same name. So
the priv->vqmmc_dev was always NULL and thus voltage switch between
modes never really suceeded.
Fix this by assigning priv->vqmmc_dev with value of the vqmmc_dev
in probe.
Fixes: 51313b49f2 ("mmc: fsl_esdhc: support SDR104 and HS200")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
- Rename DT compatible name
- Remove uneccessary if-statement to support 8-bit buswidth
- Remove redundant error msg
- Use symbolic constants in switch statement
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
When eSDHC operates at 3.3v, damage can accumulate in an internal
level shifter at a higher than expected rate. The faster the interface
runs, the more damage accumulates. This issue now is found on LX2160A
eSDHC1 for only SD card.
The hardware workaround is recommended to use an on-board level shifter
that is 1.8v on SoC side and 3.3v on SD card side.
For boards without hardware workaround, this option could be enabled,
ensuring 1.8v IO voltage and disabling eSDHC if no card.
This option assumes no hotplug, and u-boot has to make all the way to
to linux to use 1.8v UHS-I speed mode if has card.
If you do not want the workaround for better user experience, of course
you can choose to not select it running eSDHC in unsafe mode.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Cleanup this driver to use dt in U-boot and static platdata in SPL.
This requires the following steps:
1. Move all platdata assignment from probe() to ofdata_to_platdata().
This function is only called in U-boot.
2. Replicate all the platdata assignment being done in
ofdata_to_platdata() in the omapl138 board file. This data is used in
the SPL case where SPL_OF_CONTROL is not enabled.
3. Remove SPL_OF_CONTROL and related configs from omapl138_lcdk_defconfig
This cleanup effectively reverts 3ef94715cc ('mmc: davinci: fix mmc boot in SPL')
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Tested-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl69FWMACgkQ4rK92eCq
k3Vy9wgAmFLZ+u2C87A9Cs8i73QX/hs9TsjTJJPxsQWy3bOILgw8ZqBtzqD0qPvc
Mpqq7UEIZ17OW/lZCi3hqC0nGj7bT3N9rDpUQfu5Voq3GoO80yZqvCQU04AXGGpW
Aj0fjI5a6JRxQfR7XVoNw7UXPDUrDlchvBDR1GMK4cj4Sw/B+pXNDjkoJ1UWbxG6
INDgQQKhOCdMzbIsMLiUe4zkT6E8ADI0eJzgti3kWBzrdkwXZg40iEJu/MbMPRKE
Y22QZ6EkEMFTVYeCPXLU8keo4UbBIKDXWmVDbDeDbNa0QrKZ2IZ0TijajWeMWxZV
Q9J7JgpSchWcVB14vYNx+HXPUHANTA==
=bhlu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200514' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- stm32mp1: migrate MTD and DFU configuration in Kconfig
- stm32mp1: add command stm32prog
- stm32mp1: several board and arch updates
- stm32mp1: activate data cache in SPL and before relocation
- Many improvment for AV96 board and DHCOR SoM
(add new defconfig, DDR3 coding on DHCOR SoM, split between board and SOM
Synchronize DDR setttings on DH SoMs, setting for I2C EEPROM)
- clk: stm32mp1: fix CK_MPU calculation
- DT alignment of stm32mp1 device tree with Linux 5.7-rc2
Change the mmc displayed name in U-Boot for stm32_sdmmc2 driver to
“STM32 SD/MMC”.
This stm32_sdmmc2 driver is for version 2 of the ST HW IP SDMMC but the
displayed name "STM32 SDMMC2" is confusing for user, between the
instance of SDMMC and the device identifier of MMC.
For example on EV1 board, we have:
STM32MP1> mmc list
STM32 SDMMC2: 0 (SD)
STM32 SDMMC2: 1 (eMMC)
Changed to more clear:
STM32MP1> mmc list
STM32 SD/MMC: 0 (SD)
STM32 SD/MMC: 1 (eMMC)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
If CONFIG_MMC_SDHCI_SDMA is enabled but the HW could not support it,
we no longer error out. Instead we do not enable it in the host.
Change the output from printf to debug as this isn't an error but only
additional information now.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
If Host controller doesn't support SDMA, it doesn't need to return
error. Because it can be worked with PIO mode.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Use phys2bus macro when dma address is accessed.
Some targets need to use pyhs2bus macro. (e.g, RPI4)
After applied it, SDMA mode can be used.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
