This patch adds default eth pinctrl for all boards.
There are two pinctrl nodes used for two scenarios:
ephy_iot_mode - for IOT boards which have only one port (PHY0)
ephy_router_mode - For routers which have more than one ports
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds default p0led status and phy0 link polling for all boards.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch add support for mt7628-eth to isolate LAN/WAN ports mainly to
prevent LAN devices from getting IP address from WAN.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
When received a packet with an invalid length recorded in rx descriptor,
we should free this rx descriptor to allow us to continue to receive
following packets.
Without doing so, u-boot will stuck in a dead loop trying to process this
invalid rx descriptor.
This patch adds a call to mt7628_eth_free_pkt() after received an invalid
packet length.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7628 has an embedded ethernet switch (5 phy ports + 1 cpu port).
Although in IOT mode only port0 is usable, the phy0 is still connected
to the switch, not the ethernet gmac directly.
This patch rewrites it and makes it optional. It can be turned on by adding
mediatek,poll-link-phy = <?> explicitly into the eth node. By default the
driver is switch mode with all 5 phy ports working without link detection.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch removes hardcoded gpio settings as they have been replaced by
pinctrl in dts, and also replaces regmap-based phy reset with a more
generic reset controller.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds slew rate calibration for mt76x8-usb-phy, removes code
which belongs to mt7620, and gets rid of using syscon and regmap by using
clock driver and reset controller.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds pinctrl support for mt7628, with a file for common pinmux
functions and a file for mt7628 which has additional support for pinconf.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Currently this driver uses a different way to implement the spi xfer,
by modifying some fields of two registers, which is incompatible with the
MTK's original SDK linux driver. This will cause the flash data being
damaged by the SDK driver.
This patch lets the mt7621_spi_set_cs() restore the original register
fields after cs deactivated.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The mt7621 spi controller supports continuous generic half-duplex spi
transaction. There is no need to cache xfer data at all.
To achieve this goal, the OPADDR register must be used as the first data
to be sent. And follows the eight generic DIDO registers. But one thing
different between OPADDR and DIDO registers is OPADDR has a reversed byte
order.
With this patch, any amount of data can be read/written in a single xfer
function call.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch lets the spi driver to use clock provided by the clk driver
since the new clk-mt7628 driver provides accurate sys clock frequency.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds a clock driver for MediaTek MT7628/7688 SoC.
It provides clock gate control as well as getting clock frequency for
CPU/SYS/XTAL and some peripherals.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
All three UARTs of mt7628 are actually MediaTek's high-speed UARTs which
support baudrate up to 921600.
The high-speed UART is compatible with ns16550 when baudrate <= 115200.
Add compatible string to dtsi file so u-boot can use it when serial_mtk
driver is built in.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The UART of MT7628 has fixed 40MHz input clock so there is no need to put
clock-frequency in every dts files. Just put it into the common dtsi file.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch adds non-DM version for mtk hsuart driver and makes it
compatible with ns16550a driver in configuration.
This is needed in SPL with CONFIG_SPL_DM disabled for reducing size.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The current brcmnand driver is based on 4.18 linux kernel which uses
mtd_set_ooblayout to set ecc layout. But nand base code in u-boot is from
old kernel which does not use this new API and expect nand_chip.ecc.layout
structure to be set. This cause nand_scan_tail function running into a bug
check if the device has a different oob size than the default ones.
This patch ports the brcmstb_choose_ecc_layout function from kernel 4.6.7
that supports the ecc layout struture and replaces the mtd_set_ooblayout
method
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
This adds support for BCM6368, BCM6328, BCM6362 and BCM63268 SoCs.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
If configuration is set to skip low level init, automatic
probe of L2 cache size is not performed and the size is set to 0.
Flushing or invalidating the L2 cache will fail in this case.
Add a static configuration (SYS_DCACHE_LINE_SIZE) with default set to 0.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Define CONFIG_SYS_MAX_FLASH_BANKS_DETECT so that number of flash banks
are automatically detected by CFI flash driver
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
J721e SoM as a 64MB HyperFlash on board. Add pinmux and DT node for the
same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add DT node for HyperBus Memory Controller in the FSS. On J721e, its not
possible to use OSPI0 and HBMC simultaneously as they are muxed within
the Flash Subsystem hence disable HBMC by default as keep OSPI enabled.
Bootloader will fixup DT when it detects HyperFlash instead of OSPI.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
AM654/J721e has HyperBus Memory Controller that supports HyperFlash and
HyperRAM devices. It provides a memory mapped interface to interact with
these devices. Add a driver to support the same.
Driver calibrates the controller, setups up for MMIO access and probes
HyperFlash child node.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Make use of CONFIG_SYS_MONITOR_BASE only when available to avoid build
error when CONFIG_SYS_MONITOR_BASE is not defined.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Add environment variables to boot kernel from a filesystem contained in
the 2nd UFS LUN. The user can boot from a ufs filesystem just by
entering the following commands.
=> setenv boot ufs
=> boot
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add Support for commands to initialize and configure UFS devices.
TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
