With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MMC_LEGACY & SD_LEGACY are not differentiated timings in the spec and
don't have any meaningful differences. Therefore, get rid of all
references to SD_LEGACY and use MMC_LEGACY to mean both of them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the sdhci_deferred_probe() function to register as the
deferred_probe() callback to the mmc core. It will in turn call the
deferred_probe() callback of the platform drivers as declared in the
sdhci_ops.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add a deferred_probe() API for platforms that want to do some
configurations just before starting to enumerate the device.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Initial DesignWare based DM support for Cortina Access CAxxxx SoCs.
Signed-off-by: Arthur Li <arthur.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Currently the ofdata_to_platdata() method calls dev_read_addr_pci(),
which potentially accesses the parent PCI bus. If this happens before
the parent PCI bus is probed the resulting address will be wrong.
This behavior was triggered by commit 82de42fa14 ("dm: core:
Allocate parent data separate from probing parent").
According to a comment in drivers/pci/pci-uclass.c [1] accessing
the PCI parent bus in ofdata_to_platdata() is not allowed, and the
access should be moved to the probe() function.
Move the call to dev_read_addr_pci() and the related handling of the
'addr' value from the ofdata_to_platdata() to its own function,
which is then called from the probe() method.
While moving the code, the comment /* try Processor Local Bus device
first */ was dropped. It was initially added with commit 3db886a5bf
("serial: ns16550: Support ns16550 compatible pci uart devices") and
later made obsolete with commit 33c215af4b ("dm: pci: Add a function
to read a PCI BAR").
[1] Comment in drivers/pci/pci-uclass.c:
"A common cause of this problem is that this function is called in the
ofdata_to_platdata() method of @dev. Accessing the PCI bus in that
method is not allowed, since it has not yet been probed. To fix this,
move that access to the probe() method of @dev instead."
Fixes: 82de42fa14 ("dm: core: Allocate parent data separate from probing parent")
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com> # Tested on Intel Galileo
If all branches of a switch statement have a return instruction, all
subsequent lines are unreachable.
Identified with cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When flow id is not marked as valid, sysfw reads the register value to
get the range of flow ids that are supported. Then compares the flow range
with the U-Boot's host id. This will definitely fail as board
configuration doesn't assign the full range to U-Boot's host id. In order
to work around this, mark the flow id as valid and pass range as 0.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
SYSFW v2020.01 and later versions no longer supports the below messages:
- TI_SCI_MSG_RM_RING_GET_CFG
- TISCI_MSG_RM_UDMAP_TX_CH_GET_CFG 0x1206
- TISCI_MSG_RM_UDMAP_RX_CH_GET_CFG 0x1216
- TISCI_MSG_RM_UDMAP_FLOW_GET_CFG 0x1232
- TISCI_MSG_RM_UDMAP_FLOW_SIZE_THRESH_GET_CFG 0x1233
There are no users in U-Boot for any of the above messages, So drop the
support for all the corresponding messages.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix the macro to set the pplmsb field (bit 3) of the RASTER_TIMING_0
register. It is used in order to support up to 2048 pixels per line.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Created in preparation to support driver-model, they can also be called
from legacy code. In this way, code duplication is avoided.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
In case of null error, round rate is equal to target rate, so it is
useless to continue to search the DPLL setup parameters to get the
desidered pixel clock rate.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The latest data manual SPRSP08I –NOVEMBER 2017–REVISED DECEMBER 2019[1]
for am65xx SoC states the new MPU nominal voltages to be 1.1V (OPP_NOM),
1.2V (OPP_OD) and 1.24V (OPP_TURBO). Update the nominal voltages in the
K3 AVS driver to reflect this.
[1] http://www.ti.com/lit/gpn/am6528
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ESM (Error Signal Monitor) is used on certain PMIC versions to
handle error signals propagating from rest of the system. If these
reach the PMIC, it is typically a last resort fatal error which
requires a system reset. The ESM driver does the proper configuration
for the ESM module to reach this end goal. Initially, only TPS65941
PMIC is supported for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
The ESM (Error Signaling Module) is used to route error signals within
the K3 SoCs somewhat similar to interrupts. The handling for these is
different though, and can be routed for hardware error handling, to
be handled by safety processor or just as error interrupts handled
by the main processor. The u-boot level ESM driver is just used to
configure the ESM signals so that they get routed to proper destination.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
TPS65941 can have child devices under it (like the ESM support), so
probe these once the master pmic node completes probe.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Descend to drivers/soc directory unconditionally for SPL and U-Boot
builds. Individual drivers can have their own config to check what needs
to be built for SPL. There should be no increase in SPL code size
due to this change.
This is required on K3 SoCs to support DMA in SPL.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add driver flag to skip power domain disabling on device removal.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
In various cases a power domain must stay enabled after device
removal when booting OS (i.e. serial debug console or display).
Add a flag to selectively skip switching off a power domain.
Fixes: 52edfed65d ("dm: core: device: switch off power domain after device removal")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Guillaume La Roque <glaroque@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We should not assign a value that is overwritten before use.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This adds a compatible string for m41st87. This ensures that this driver
can be used for m41st87.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
After the commit 9b643e312d ("treewide: replace with error()
with pr_err()"), there are pr_err() usages without line break. Add
missing line breaks for pr_err() used in f_thor.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
In case dfu command is being executed with timeout option,
the timer may expire in the middle of DFU operation. If there
is DFU request coming, we may simple reset timeout value
to prevent aborting of ongoing DFU operation.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Ferry Toth <ftoth@exalondelft.nl>
Commit 06985289d4 ("watchdog: Implement generic watchdog_reset()
version") introduced an automatic selection of CONFIG_WATCHDOG by
CONFIG_WDT. But for boards selecting CONFIG_HW_WATCHDOG, like
boards have a powerpc 8xx, CONFIG_WATCHDOG shall not be selected
as they are mutually exclusive.
Make CONFIG_WATCHDOG dependent on !CONFIG_HW_WATCHDOG
Fixes: 06985289d4 ("watchdog: Implement generic watchdog_reset() version")
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Stefan Roese <sr@denx.de>
Commit f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros
cleanup") switched the watchdog to CONFIG_WATCHDOG. But this is not
compatible with the 8xx because it starts the watchdog HW timer at
reset and must be serviced from the very beginning including while
U-boot is executed in the firmware before relocation in RAM.
Select CONFIG_HW_WATCHDOG and make hw_watchdog_reset() visible.
Meanwhile, finalise the cleanup of arch/powerpc/cpu/mpc8xx/Kconfig by
removing the lines put in comment in that commit, and also remove
again the selection of CONFIG_MPC8xx_WATCHDOG which was removed by
that commit and brought back by mistake by commit b3134ffbd9
("watchdog: Kconfig: Sort entry alphabetically")
Note that there was an 'imply WATCHDOG' in the original commit but
it disappeared in the Kconfig alphabetical sorting, so no need to
remove it here.
Fixes: f3729ba6e7 ("watchdog: mpc8xx_wdt: Watchdog driver and macros cleanup")
Fixes: b3134ffbd9 ("watchdog: Kconfig: Sort entry alphabetically")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Stefan Roese <sr@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Driver probe function is called again and again in case of error.
Malloc space is getting full which is is reported by:
Insufficient RAM for page table: 0x15000 > 0x14000.
Please increase the size in get_page_table_size()
### ERROR ### Please RESET the board ###
The patch is freeing allocated buffers on error path to avoid panic.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
On Xilinx ZynqMP revA board initial value of PHYCR register is 0x5448 which
means FORCE_LINK_GOOD is already setup. Origin code was doing write but the
new code is doing read/modify/write and keep this bit untouched. That's why
ethernet stop to work.
The patch is cleaning this bit when PHYCR value is composed.
Tested on Xilinx zcu102-revA and zcu104-rev1.0 boards.
Fixes: 37d6265f2b ("net: phy: dp83867: refactor rgmii configuration")
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Fixed wrong enumeration of nand_config structure. Added chip select
function before reading the nand chip for maf/dev id's, without this
unable to access id's from some of the micron chips. Also added a
print statement to identify if a nand flash is using on-die ecc.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The clock driver makes EEMI call to get the name of invalid clk
when executing versal_get_clock_info() function. This results in
error messages.
Added check for validating clock before saving clock attribute and
calling versal_pm_clock_get_name() in versal_get_clock_info() function.
Signed-off-by: Rajan Vaja <rajan.vaja@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
flush_dcache_range() expects unsigned long in the arguments. Here u32
variable is unable to hold the higher address value when ddr mapped
to higher addresses & flushing lower address dchache range instead
which is unmapped causing to crash.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Its possible that k3_avs_priv is NULL because the driver may not have
been probed yet. Therefore check if pointer is valid before
dereferencing it.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This reverts commit 1ee4942918.
Commit 1ee4942918 ("ata: fsl_ahci: Add sata DM support for Freescale
powerpc socs") introduced SCSI layer to call AHCI private API in order
to support sata operations, In DM mode, This is not necessary for
non-AHCI sata. So revert it and have already updated the driver itself
to operate sata directly.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
This driver currently performs cache operation before the DMA start,
but does nothing after the DMA completion.
When reading data by DMA, the cache invalidation is needed also after
finishing the DMA transfer. Otherwise, the CPU might read data from
the cache instead of from the main memory when speculative memory read
or memory prefetch occurs.
Instead of calling the cache operation directly, this commit adds
dma_unmap_single(), which performs cache invalidation internally,
but drivers do not need which operation is being run.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, sdhci_prepare_dma() calls flush_cache() regardless of the
DMA direction.
Actually, cache invalidation is enough when reading data from the device.
This is correctly handled by dma_map_single(), which mimics the DMA-API
in Linux kernel. Drivers can be agnostic which cache operation occurs
behind the scene.
This commit also sanitizes the difference between the virtual address
and the dma address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
host->mmc is already (struct mmc *).
memalign() returns an opaque pointer, so there is no need for casting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Use {lower,upper}_32_bits() instead of the combination of cast
and shift.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The same code is run for both SDHCI_QUIRK_32BIT_DMA_ADDR and
define(CONFIG_FIXED_SDHCI_ALIGNED_BUFFER).
Unify the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Using the global variable does not look nice.
Add a new field sthci::align_buffer to point to the bounce buffer.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The implementation of dma_map_single() and dma_unmap_single() is
exactly the same for all the architectures that support them.
Factor them out to <linux/dma-mapping.h>, and make all drivers to
include <linux/dma-mapping.h> instead of <asm/dma-mapping.h>.
If we need to differentiate them for some architectures, we can
move the generic definitions to <asm-generic/dma-mapping.h>.
Add some comments to the helpers. The concept is quite similar to
the DMA-API of Linux kernel. Drivers are agnostic about what is
going on behind the scene. Just call dma_map_single() before the
DMA, and dma_unmap_single() after it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
Unfortunately a recent change adjusted the order of the checks here such
that 400MHz now shows up as fast-plus speed (1Mbps). Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: d96440d1e3 ("i2c: designware_i2c: Add support for fast-plus speed")
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 01298da31d ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Solve type issue in stm32mp1_lse_enable and stm32mp1_clktree.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
clk_stm32mp1.c: In function ‘stm32mp1_lse_enable’:
clk_stm32mp1.c:1238:15: warning: comparison of integer expressions
of different signedness: ‘u32’ {aka ‘unsigned int’} and ‘int’
[-Wsign-compare]
clk_stm32mp1.c:1239:13: warning: comparison of integer expressions
of different signedness: ‘u32’ {aka ‘unsigned int’} and ‘int’
[-Wsign-compare]
clk_stm32mp1.c: In function ‘stm32mp1_clktree’:
clk_stm32mp1.c:1814:17: warning: comparison of integer expressions
of different signedness: ‘int’ and ‘unsigned int’
[-Wsign-compare]
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Use int as result of dm_i2c_reg_read to avoid warning with
W=1 (warning: comparison is always false due to limited range
of data type [-Wtype-limits])
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
There is no reason to show RAM_ROCKCHIP_DEBUG entry in other .config files
as I see it for Xilinx ZynqMP.
\# CONFIG_U_QE is not set
\# CONFIG_RAM is not set
CONFIG_RAM_ROCKCHIP_DEBUG=y
Add missing dependency on RAM_ROCKCHIP driver.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
HDMI PLL has its own xtal with 27 MHz output but we treat it the same
way as other PLLs with 33.33 MHz input.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl48iogACgkQfxc6PpAI
reaVzAf/an3/yKe6r3CVWlcRV6H/dVg1ApnnLpX7jS0p0b++oCVvOiy7z1WPXj3k
b1SSgENDeeZ/8EHio+Gf7ZidH/TGEj7L6YEFwd1t60GMkZiWEkNf4Z53tw482YG+
96hoPD+ySTW+ddIdVHWAFG2I4aEiKHANJAp/ItNdD+rLbrEwNQy+eiK5JTOk80B6
/X8AJCLZeAC1s7vs+2+WolgjT78QGzA9HHalMiublcqh0ivKKk0QeQiOKKPe8JYJ
om5YY1TxayQ60Xmo5f39/SBfzEEklxw83sU9o1tBeYzyVUpu7fQdkxiDbWdsij77
DgwLdeYQJGbN+hdSWE0gjTqyhW+lWA==
=KRoA
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-6feb20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
sandbox conversion to SDL2
TPM TEE driver
Various minor sandbox video enhancements
New driver model core utility functions
The commit e8e9715df2 ("regulator: fixed: Modify enable-active-high behavior")
fixed the regulator driver behavior when 'enable-active-high' is defined.
Unfortunately, this patch used dm_regulator_platdata()'s "boot_on" member
to set GPIOD_IS_OUT_ACTIVE flag and enable the regulator.
The issue here is that regulator_common_ofdata_to_platdata() is called
_before_ regulator_pre_probe() function in which the 'regulator-boot-on'
property is asserted.
As a result the GPIOD_IS_OUT_ACTIVE flag is not set and gpio_request_by_name()
called in the former function is not enabling the regulator.
This is problematic for e.g. i.MX ethernet driver, which then tries to
perform initialization without power (and fails).
The solution here is to explicitly enable regulator in regulator_pre_probe()
callback only when 'regulator-boot-on' property is present in device tree.
The GPIOD_IS_OUT_ACTIVE flag is not set at all, but relevant gpio is
requested.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrice Chotard <patrice.chotard@st.com>
- Move P2SB from Apollo Lake to a more generic location
- Add a function to find a device by drvdata in DM core
- Enhancement of DM IRQ uclass driver
- Add a clock driver for Intel devices
- Add support for ACPI general-purpose events
- Add a TPM driver for H1/Cr50
- Enable TPM on Google Chromebook Coral
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXkGKMg4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXCY3AJ9zzSWCPRa6M6YbYiHyfasyP1uf+gCdG2bMDRaC
vNpAeNnM9aWgJMkje6k=
=al8x
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix Coverity CID 280902 issue in vid_console_color()
- fix vid_console_color() build warning
- fix for mxsfb to ensure correct Linux logo position
Set the correct offset length and chip address offset mask for each
device to allow correct access to total capacity of the devices.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Since commit bcee8d6764 ("dm: gpio: Allow control of GPIO uclass in SPL")
CONFIG_DM_74X164 is no longer built for mx7dsabresd_defconfig, as
this target does not use CONFIG_SPL_GPIO.
Remove such dependency and let the the 74X164 GPIO driver be built
again.
This restores Ethernet functionality on the imx7-sdb board as the
Ethernet reset PHY comes from a GPIO driven by a 74LV595PW I/O
expander.
Fixes: bcee8d6764 ("dm: gpio: Allow control of GPIO uclass in SPL")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add serial UART driver support for all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
Add support for hardware watchdog timer on all Cortina Access
CAxxxx family of SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
DM_GPIO based GPIO controller driver for CAxxxx SoCs.
This driver support multiple CPU architectures and
Cortina Access SoC platforms.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
building mtk ethernet driver for aarch64 (mt7622) results
in warnings/errors
"error: cast from pointer to integer of different size"
Fixes: 23f17164d9 ("ethernet: MediaTek: add ethernet driver for MediaTek ARM-based SoCs")
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
This patch add sgmii init part for the mediatek SoC that
support sgmii mode. It is a must for mt7622.
Signed-off-by: MarkLee <Mark-MC.Lee@mediatek.com>
H1 is a Google security chip present in recent Chromebooks, Pixel phones
and other devices. Cr50 is the name of the software that runs on H1 in
Chromebooks.
This chip is used to handle TPM-like functionality and also has quite a
few additional features.
Add a driver for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present driver model supports the IRQ uclass but there is no way to
request a particular interrupt for a driver.
Add a mechanism, similar to clock and reset, to read the interrupts
required by a device from the device tree and to request those interrupts.
U-Boot itself does not have interrupt-driven handlers, so just provide a
means to read and clear an interrupt. This can be useful to handle
peripherals which must use an interrupt to determine when data is
available, for example.
Bring over the basic binding file as well, from Linux v5.4. Note that the
older binding is not supported in U-Boot; the newer 'special form' must be
used.
Add a simple test of the new functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add an IRQ type to each driver and use irq_first_device_type() to find
and probe the correct one.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There can be different types of interrupt controllers in a system and some
drivers may need to distinguish between these. In general this can be
handled using the device tree by adding the interrupt information to
device nodes.
However on x86 devices we have interrupt controllers which are not tied
to any particular device and not really used in U-Boot. These still need
to be inited, so a convenient method is to give each controller a type
and allow a particular controller type to be probed.
Add support for this in sandbox along with a test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: remove the new bland line at EOF of test/dm/irq.c]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
So far we have avoided adding a clock driver for Intel devices. But the
Designware I2C driver needs a different clock (133MHz) on Intel devices
than on others (166MHz). Add a simple driver that provides this
information.
This driver can be expanded later as needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have uclass_first_device_drvdata(), use it from the I2C driver
to reduce code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have uclass_first_device_drvdata(), use it from syscon to
reduce code duplication.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is sometimes useful to find a device in a uclass using only its driver
data. The driver data often indicates the 'subtype' of the device, e,g,
via its compatible string.
Add a function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This partially reverts changes by commit 2cc393f32f
("video: make BPP and ANSI configs optional") since it
caused issues with other boards (missing LCD console
output on pinebook, x86 platform or sandbox). Enable
all disabled options again and opt out of not supported
color depth in board defconfigs.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Now that we can use direct access to the system malloc() in sandbox, drop
the remaining uses of os_malloc().
The only one remaining now is for the RAM buffer, which we do want to be
at a known address, so this is intended.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most files don't need this header and it pulls in quite of lots of stuff,
malloc() in particular. Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add a new device-tree property to control the colour depth. At present we
support 16bpp and 32bpp.
While we are here, update the code to use livetree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
On high-DPI displays U-Boot's LCD window can look very small. Add a
-K flag to expand it to make things easier to read, while still using
the existing resolution internally.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present an error does not stop the sound-output loop. This is incorrect
since nothing can be gained by trying to continue. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no positive indication that U-Boot has finished
sending sound data. This means that it is not possible to power down an
audio codec, for example. Add a new method that is called once all sound
data has been sent.
Add a new method for this, called when the sound_play() call is done.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function name conflicts with our desire to #define free() to
something else on sandbox. Since it deals with resources, rename it to
rfree().
Signed-off-by: Simon Glass <sjg@chromium.org>
For sandbox we want to have the maximum possible build coverage, so enable
all colour depths for video.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
At present only a 16bpp display is supported for Truetype fonts. Add
support for 32bpp also since this is quite common.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This adds a subcommand to dm to dump out what drivers are installed, and their
compatible strings. I have found this useful in ensuring that I have the correct
drivers compiled, and that I have put in the correct compatible strings.
Signed-off-by Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This currently reads the uclass's private data in the ofdata_to_platdata
method which is not allowed, since the uclass has not read it from the
device tree. This happens in the probe method.
Fix it by adding a probe() method and moving the code there.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to process all children, making sure they are
probed first. Add functions to help with this and a macro to make it more
convenient.
Signed-off-by: Simon Glass <sjg@chromium.org>
When generating ACPI tables we need to make sure that all devices have
read their platform data, so that they can generate the tables correctly.
Rather than adding this code in ACPI, create a core function to handle it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a function to read a property from the chosen node, providing access
to its length. Update ofnode_get_chosen_string() to make use of it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Now that we have ofnode_read_prop() we can rewrite this function using
that one, reducing the amount of duplicated code.
Update ofnode_read_size() and move it up next to the other similar
functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new function to read a property that supports reading the length as
well.
Reimplement ofnode_read_string() using it and fix its comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is actually intended to read a string rather than a
property. All of its current callers use it that way. Also there is no way
to return the length of the property from this function.
Rename it to better indicate its purpose, using ofnode_read as the prefix
since this matches most other functions.
Also add some tests which are missing for these functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
These functions do not modify the device so should use a const pointer to
it. Update the code accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this method uses a non-const udevice pointer, but the call
should not modify the device. Use a const pointer.
Signed-off-by: Simon Glass <sjg@chromium.org>
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
-----BEGIN PGP SIGNATURE-----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=Sv9b
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2020.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-raspberrypi
- DFU support file operations lager then the default max size
- add dfu support to dwc2 for bcm2835
- enable DFU for RPi4
- Fix RPi4 memory map to include the genet device
- add driver for the genet ethernet device
- enable network support in RPi4 config
Add DDR2 support to Gen5 DRAM driver. As the DDR2 macro names generated
by Quartus are named differently than the DDR3 ones, use anon unions to
store them in the same structures, without growing their size.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add optional support for fetching watchdog clock rate from DT
and ungating reset via reset framework. This is optional as not
all platforms using DW WDT support the clock and reset frameworks
yet.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Convert the designware watchdog timer driver to DM and add DT probing
support. Perform minor coding style clean up, like drop superfluous
braces. These ought to be no functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # roc-rk3399-pc
Add DM_FLAG_OS_PREPARE flag to ensure that the driver's
remove() callback is invoked before booting the kernel.
This is required to stop the LCDIF controller. This was
the behaviour with old driver without DM_VIDEO support.
Without stopping the LCDIF we sometimes observe incorrect
Linux logo position.
Fixes: ae0760584b ("imx: mx6ul_14x14_evk: convert to DM_VIDEO")
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reported-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Fix:
>>> CID 280902: Control flow issues (MISSING_BREAK)
>>> The case for value "VIDEO_BPP32" is not terminated
>>> by a 'break' statement.
Also fix
error: control reaches end of non-void function [-Werror=return-type]
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Various minor fixes for x86
- Switch to ACPI mode on Intel edison
- Support run-time configuration for NS16550 driver
- Update coreboot and slimbootloader serial drivers to use NS16550
run-time configuration
- ICH SPI driver fixes to hardware sequencing erase case
- Move ITSS from Apollo Lake to a more generic location
- Intel GPIO driver bug fixes
- Move to vs2017-win2016 platform build host for Azure pipelines
This adds DM_FLAG_PRE_RELOC flag to probe i2c driver
before relocation
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix the following in intel_gpio_get_value():
* The value of the register is contained in the variable 'reg', not in
'mode'. The variable 'mode' contains only the configuration whether
the gpio is currently an input or an output.
* The correct bitmasks for the input and output value are
PAD_CFG0_RX_STATE and PAD_CFG0_TX_STATE.
Use them instead of the currently used PAD_CFG0_RX_STATE_BIT and
PAD_CFG0_TX_STATE_BIT.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add missing 'PAD_CFG0_TX_STATE' to the clear mask for pcr_clrsetbits32().
Otherwise this bit cannot be cleared again after it has been set once.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The function pcr_clrsetbits32() expects a device with a P2SB parent
device. In intel_gpio_direction_output() and intel_gpio_set_value()
the device 'dev' is passed to pcr_clrsetbits32(), which is a
gpio-controller with a device 'pinctrl' as parent. This does not match
the expectations of pcr_clrsetbits32(). But the 'pinctrl' device has a
P2SB as parent.
Pass the 'pinctrl' device instead of the 'dev' device to
pcr_clrsetbits32().
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The watchdog timer value was never updated in the hardware by this
driver, so the watchdog triggered on some random stale value that
was left in the hardware. The TI SPRUH37C says, quote:
20.4.3.9 Modifying Timer Count/Load Values and Prescaler Setting
...
After a write access, the load register value and prescaler ratio
registers are updated immediately, but new values are considered
only after the next consecutive counter overflow or after a new
trigger command (the WDT_WTGR register).
This means at least one trigger must happen. The driver probably
depended on someone calling it's .reset() callback, however that
is not guaranteed e.g. if the WDT operates without servicing.
Add this missing trigger.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The timeout parameter of omap3_wdt_start() is in miliseconds, while
GET_WLDR_VAL() expects parameter in seconds. Fix this so the WDT
driver is actually usable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Sam Protsenko <semen.protsenko@linaro.org>
Cc: Suniel Mahesh <sunil.m@techveda.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add "ti,keystone-gpio" compatible so as be able to use Linux DT files as
is.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix below compiler warning for 64bit builds
drivers/gpio/da8xx_gpio.c: In function ‘davinci_get_gpio_bank’:
drivers/gpio/da8xx_gpio.c:446:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
return (struct davinci_gpio *)addr;
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
J721e EVM has a TCA6424 IO expander that has 24 GPIOs. Add support for
the same
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The code in this file is not specific to Apollo Lake. According to
coreboot sources (where this code comes from), it is common to at least:
* Apollo Lake
* Cannon Lake
* Ice Lake
* Skylake
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When ich_spi_exec_op_hwseq() is called to erase a 4k block
(opcode = SPINOR_OP_BE_4K), it expects to find a length value in
op->data.nbytes, but that value is always 0. As a result, the while loop
is never executed and no erase is carried out.
Fix this by dropping the loop code entirely, only keeping the relevant
parts of the loop body.
See http://patchwork.ozlabs.org/patch/1222779/ for more detailed
background information and discussion.
Signed-off-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Coreboot can provide information about the serial device in use on a
platform. Add a driver that uses this information to produce a working
UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present this driver uses an assortment of CONFIG options to control
how it accesses the hardware. This is painful for platforms that are
supposed to be controlled by a device tree or a previous-stage bootloader.
Add a new CONFIG option to enable fully dynamic configuration. This
controls register spacing, size, offset and endianness.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Aiden Park <aiden.park@intel.com>
Tested-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: squashed in http://patchwork.ozlabs.org/patch/1232929/]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Migrate CONFIG_DESIGNWARE_WATCHDOG to Kconfig and update the headers
accordingly, no functional change. The S10 enables the WDT only in
SPL, but does not enable it in U-Boot itself, hence disable it in
the config again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dalon Westergreen <dwesterg@gmail.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Philipp Tomisch <philipp.tomisch@theobroma-systems.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Tien Fong Chee <tien.fong.chee@intel.com>
In Cyclone 5 SoC platform, the first USB probing is failed but second
probing is success. DWC2 USB driver read gsnpsid register right after
de-assert reset, but controller is not ready yet and it returns gsnpsid 0.
Polling reset status after de-assert reset to solve the issue.
Retry with this fix more than 10 times without issue.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add a new option to enable the DROP_FFS flag when flashing UBI images to
NAND in order to drop trailing all-0xff pages.
This is similar to the existing FASTBOOT_FLASH_NAND_TRIMFFS option.
Signed-off-by: Guillermo Rodriguez <guille.rodriguez@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Invalidate dcache line before accessing Setup Packet contents. Otherwise
driver will see stale content on non coherent architecture.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
-----BEGIN PGP SIGNATURE-----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=PvYc
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (2nd)
Denali NAND driver changes:
- Set up more registers in denali-spl for SOCFPGA
- Make clocks optional
- Do not assert reset signals in the remove hook
- associate SPARE_AREA_SKIP_BYTES with DT compatible
- switch to UCLASS_MTD
UniPhier platform changes:
- fix a bug in dram_init()
- specify loadaddr for "source" command
UCLASS_MTD is a better fit for NAND drivers.
Make NAND_DENALI_DT depend on DM_MTD, which is needed to compile
drivers/mtd/mtd-uclass.c
Also, make ARCH_UNIPHIER select DM_MTD because all the defconfig
of this platform enables NAND_DENALI_DT.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Currently, the denali NAND driver in U-Boot configures the
SPARE_AREA_SKIP_BYTES based on the CONFIG option.
Recently, Linux kernel merged a patch that associates the proper
value for this register with the DT compatible string.
Do likewise in U-Boot too.
The denali_spl.c still uses CONFIG_NAND_DENALI_SPARE_AREA_SKIP_BYTES.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
When the reset signal is de-asserted, the HW-controlled bootstrap
starts running unless it is disabled in the SoC integration.
It issues some commands to detect a NAND chip, and sets up registers
automatically. Until this process finishes, software should avoid
any register access.
Without this delay function, some of UniPhier boards hangs up while
executing nand_scan_ident(). (denali_read_byte() is blocked)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The Denali NAND driver in mainline Linux currently cannot deassert the
reset. The upcoming Linux 5.6 will support the reset controlling, and
also set up SPARE_AREA_SKIP_BYTES correctly. So, the Denali driver in
the future kernel will work without relying on any bootloader or firmware.
However, we still need to take care of stable kernel versions for a while.
U-boot should not assert the reset of this controller.
Fixes: ed784ac382 ("mtd: rawnand: denali: add reset handling")
Signed-off-by: Marek Vasut <marex@denx.de>
[yamada.masahiro: reword the commit description]
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "nand_x" and "ecc" clocks are currently optional. Make the core
clock optional in the same way. This will allow platforms with no clock
driver support to use this driver.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Marek Vasut <marex@denx.de> # On SoCFPGA Arria V
On Altera SoCFPGA, upon either cold-boot or power-on reset, the
Denali NAND IP is initialized by the BootROM ; upon warm-reset,
the Denali NAND IP is NOT initialized by BootROM. In fact, upon
warm-reset, the SoCFPGA BootROM checks whether the SPL image in
on-chip RAM is valid and if so, completely skips re-loading the
SPL from the boot media.
This does sometimes lead to problems where the software left
the boot media in inconsistent state before warm-reset, and
because the BootROM does not reset the boot media, the boot
media is left in this inconsistent state, often until another
component attempts to access the boot media and fails with an
difficult to debug failure. To mitigate this problem, the SPL
on Altera SoCFPGA always resets all the IPs on the SoC early
on boot.
This results in a couple of register values, pre-programmed by
the BootROM, to be lost during this reset. To restore correct
operation of the IP on SoCFPGA, these values must be programmed
back into the controller by the driver. Note that on other SoCs
which do not use the HW-controlled bootstrap, more registers
may have to be programmed.
This also aligns the SPL behavior with the full Denali NAND
driver, which sets these values in denali_hw_init().
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
No need to do twice data training for rk3328 ddr sdram, we re-use the
setting for both channel. And adjust the sdram_init properly for correct
init flow.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Few of the rockchip family SoC atleast rk3288,
rk3399 are sharing some cru register bits so
adding common code between these SoC families
would require to include both cru include files
that indeed resulting function declarations error.
So, create a common cru include as cru.h then
include the rk3399 arch cru include file and move
the common cru register bit definitions into it.
The rest of rockchip cru files will add it in future.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In the RK3399 DRAM driver, the function set_ds_odt() supports operating
in two different modes, selected by the ctl_phy_reg argument: when true,
the function reads and writes directly from the DRAM registers, accessed
through "chan->pctl->denali_*"; when false, the function reads and
writes from an array, accessed through "params->pctl_regs.denali_*",
which is written to DRAM registers at a later time.
However, phy_config_io(), which is called by set_ds_odt() to do a subset
of its register operations, operates directly on DRAM registers at all
times. This means that it reads incorrect values (and writes new values
prematurely) when ctl_phy_reg in set_ds_odt() is false. Fix this by
passing in the address of the registers to work with.
This prevents an "Invalid DRV value" error in the SPL debug log and
(presumably) results in a more correct end state. See the following logs
from a RK3399 NanoPi M4 board (4GB LPDDR3):
Before:
sdram_init() Starting SDRAM initialization...
phy_io_config() Invalid DRV value.
phy_io_config() Invalid DRV value.
sdram_init() sdram_init: data trained for rank 2, ch 0
phy_io_config() Invalid DRV value.
phy_io_config() Invalid DRV value.
sdram_init() sdram_init: data trained for rank 2, ch 1
Channel 0: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
256B stride
sdram_init() Finish SDRAM initialization...
After:
sdram_init() Starting SDRAM initialization...
sdram_init() sdram_init: data trained for rank 2, ch 0
sdram_init() sdram_init: data trained for rank 2, ch 1
Channel 0: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR3, 933MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
256B stride
sdram_init() Finish SDRAM initialization...
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Broadcom GENET Ethernet MACs are used in several MIPS based SoCs
and in the Broadcom 2711/2838 SoC used on the Raspberry Pi 4.
There is no publicly available documentation, so this driver is based
on the Linux driver. Compared to that the queue management is
drastically simplified, also we only support version 5 of the IP and
RGMII connections between MAC and PHY, as used on the RPi4.
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
[Andre: heavy cleanup and a few fixes]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Broadcom 2835 SoC requires special conversion of physical memory addresses
for DMA purpose, so add needed wrappers to dwc2_udc_otg driver. Also extend
the list of compatible devices with 'brcm,bcm2835-usb' entry. This allows
to use USB gadget drivers (i.e. DFU) on Raspberry Pi4 boards.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Add support for operations on files larger than
CONFIG_SYS_DFU_MAX_FILE_SIZE. The buffered io mechanism is still used for
aggregating io requests, so for files up to CONFIG_SYS_DFU_MAX_FILE_SIZE
nothing is changed and they will be handled in a single filesystem call.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Rename functions for bufferred file io operations to make them easier to
understand. Also add missing file offset argument to them (currently
unused). All this is a preparation to remove predefined file size limit
(CONFIG_SYS_DFU_MAX_FILE_SIZE) for DFU read/write operations.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
i2c changes for 2020.04
- updates the Designware I2C driver
- get timings from device tree
- handle units in nanoseconds
- make sure that the requested bus speed is not exceeded
- few smaller clean-ups
- adds enums for i2c speed and update drivers which use them
- global_data: remove unused mxc_i2c specific field
Add a driver for the regulators in the the DA9063 PMIC.
Robert Beckett: move regulator modes to header so board code can set
modes. Correct mode mask used in ldo_set_mode.
Add an option CONFIG_SPL_DM_REGULATOR_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
This adds the basic register access operations and child regulator
binding (if a regulator driver exists).
Robert Beckett: simplify accesses by using bottom bit of address as
offset overflow. This avoids the need to track which page we are on.
Add an option CONFIG_SPL_DM_PMIC_DA9063.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
The 3-bit "command", or register, is encoded within the device address.
Configure the device accordingly, and pass command in DM I2C read/write
calls correctly.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
TI's AM654 SoC has a Cadence OSPI IP. Add a new compatible string for
the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Cadence OSPI is similar to QSPI IP except that it supports Octal IO
(8 IO lines) flashes. Add support for Cadence OSPI IP with existing
driver using new compatible
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Octal flash devices. Octal flash devices use 8 IO lines
for data transfer. Currently only 1-1-8 Octal Read mode is supported.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for Direct Access Controller mode of Cadence QSPI. This
allows MMIO access to SPI NOR flash providing better read performance.
Direct mode is only exercised if AHB window size is greater than 8MB.
Support for flash address remapping is also not supported at the moment
and can be added in future.
For better performance, driver uses DMA to copy data from flash in
direct mode using dma_memcpy().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Current Cadence QSPI driver has few limitations. It assumes all read
operations to be in Quad mode and thus does not support SFDP parsing.
Also, adding support for new mode such as Octal mode would not be
possible with current configuration. Therefore move the driver over to spi-mem
framework. This has added advantage that driver can be used to support
SPI NAND memories too.
Hence, move driver over to new spi-mem APIs.
Please note that this gets rid of mode bit setting done when
CONFIG_SPL_SPI_XIP is defined as there does not seem to be any user to
that config option.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has supported W25N01GV for a long time, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Make sure corresponding setup registers are updated depending on CS.
This ensures that driver can support QSPI flashes on ChipSelects other
than on CS0
Reported-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The SPI stack relies on a proper bus speed/mode configuration
by calling dm_spi_claim_bus(). However the hitherto code
allowed to accidentally override those settings in
the spi_get_bus_and_cs() routine.
The initially established speed could be discarded by using
the slave platdata, which turned out to be an issue on
the platforms whose slave maximum supported frequency
is not on par with the maximum frequency of the bus controller.
This patch fixes above issue by configuring the bus from
spi_get_bus_and_cs() only in case it was not done before.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add chip select number check in spi_find_chip_select().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> # SoPine
This is a port of the kernel's spi-nxp-fspi driver. It uses the new
spi-mem interface and does not expose the more generic spi-xfer
interface. The source was taken from the v5.3-rc3 tag.
The port was straightforward:
- remove the interrupt handling and the completion by busy polling the
controller
- remove locks
- move the setup of the memory windows into claim_bus()
- move the setup of the speed into set_speed()
- port the device tree bindings from the original fspi_probe() to
ofdata_to_platdata()
There were only some style change fixes, no change in any logic. For
example, there are busy loops where the return code is not handled
correctly, eg. only prints a warning with WARN_ON(). This port
intentionally left most functions unchanged to ease future bugfixes.
This was tested on a custom LS1028A board. Because the LS1028A doesn't
have proper clock framework support, changing the clock speed was not
tested. This also means that it is not possible to change the SPI
speed on LS1028A for now (neither is it possible in the linux driver).
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Move some of the code currently in the ofdata_to_platdata() method to
probe() so that it is not executed when generating ACPI tables.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to be able to calculate the speed separately from actually setting
the speed, so we can generate the required ACPI tables. Split out the
calculation into its own function.
Drop the double underscore on __dw_i2c_set_bus_speed while we are here.
That is reserved for compiler internals.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is used to store the speed information for a bus. We want to provide
this to ACPI so that it can tell the kernel. Move this struct to the
header file so it can be accessed by the ACPI i2c implementation being
added later.
Signed-off-by: Simon Glass <sjg@chromium.org>
Convert the obvious uses of i2c bus speeds to use the enum.
Use livetree access for code changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Note: This driver needs to move to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Update this driver to use the new standard enums for speed.
Note: This driver needs to move to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some versions of this peripheral include a spike-suppression phase of the
bus. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present the driver can end up with timing parameters which are slightly
faster than those expected. It is possible to optimise the parameters to
get the best possible result.
Create a new function to handle the timing calculation. This uses a table
of defaults for each speed mode rather than writing it in code.
The function works by calculating the 'period' of each bit on the bus in
terms of the input clock to the controller (IC_CLK). It makes sure that
the constraints are met and that the different components of that period
add up correctly.
This code was taken from coreboot which has ended up with this same
driver, but now in a much-different form.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Create a struct to hold the three timing parameters. This will make it
easier to move these calculations into a separate function in a later
patch.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Instead of passing this parameter into __dw_i2c_set_bus_speed(), pass in
the driver's private data, from which the function can obtain that
information. This allows the function to have access to the full state of
the driver.
Signed-off-by: Sicomp_param1mon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The i2c controller defines a few timing properties. Read these in and
store them for use by the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
At present the driver uses an approximation for the bus clock, e.g. 166MHz
instead of 166 2/3 MHz.
This can result in small errors in the resulting I2C speed, perhaps 0.5%
or so.
Adjust the existing code to start from the accurate figure, even if later
rounding reduces this accuracy.
Update the bus speed code to work in KHz instead of MHz, which removes
most of the error.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Group these #defines into an enum to make it easier to understand the
relationship between them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some SoCs support a higher speed than what is currently called 'max' in
this driver. Rename it to 'high' speed, which is the official name of the
3.4MHz speed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
We use struct clk here so really should include this header file to avoid
build errors. Also switch the order of clk.h in the C file to match the
required code style.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
If a different input clock is required then the correct way to do this is
with a clock driver. Don't allow boards to override IC_CLK.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Some versions of this peripherals provide more control of the bus
behaviour. Add definitions for these registers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jun Chen <ptchentw@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_av_set_rate(). If it is 0, let's return with -EINVAL.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Guard 'mfd==0' to prevent 'divide by zero' issue in
clk_pplv3_av_get_rate(). If it is 0, let's return with EIO since mfd
should never be 0 at all.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Guard 'parent_rate==0' to prevent 'divide by zero' issue in
clk_pplv3_sys_get_rate(). If it is 0, let's return with -EINVAL.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
m68k needs block cache list initialized after relocation.
Other architectures must not be involved.
Fixing regression related to:
commit 1526bcce0f
("common: add blkcache init")
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
This function parameter usage of load_addr was incorrectly caught in
the clarifying renames of commit bb872dd930, which results in boot
failures on Marvell A38x.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
Patch-to: Simon Glass <sjg@chromium.org>
clk_get_by_name() requires clk_get_by_id() that is not available if
CONFIG_OF_PLATDATA is defined, so move clk_get_by_name() into #else
condition of #if CONFIG_IS_ENABLED(OF_PLATDATA).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
mtk_clk_find_parent_rate is calling clk_get_rate to know the rate
of a parent clock. clk_get_rate returns a ulong, while
mtk_clk_find_parent_rate returns an int. This implicit cast creates
an issue for clock rates big enough to need the full 32 bits to
store its data. When that happen the clk rate will become incorrect
because of the implicit cast between ulong -> int -> ulong.
This commit change the return type of mtk_clk_find_parent_rate to
ulong.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
On m68k, block_cache list is relocated, but next and prev list
pointers are not adjusted to the relocated struct list_head address,
so the first iteration over the block_cache list hangs.
This patch initializes the block_cache list after relocation.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
Reviewed-by: Eric Nelson <eric@nelint.com>
Now that arch specific dma mapping APIs take care of cache
flush/invalidate, drop local cache flush operation.
While at that fix dma_unmap_single() call to match new prototype
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch includes the following:
1. Add fastboot command to erase the whole EMMC_USER
2. Add fastboot command to flash image at EMMC_BOOT1
3. Add fastboot command to erase the whole EMMC_BOOT1
4. Enale CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT for mt8518
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
Function mod_exp_sw() is only used via the operators of the uclass.
It is not defined in any include.
Make mod_exp_sw() static.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
drivers/rng/sandbox_rng.c requires rand() to be defined but configuration
option CONFIG_CONFIG_LIB_RAND selected in drivers/rng/Kconfig does not
exist.
test/lib/test_aes.c requires rand() to be defined.
Fix the selection criteria for choice "Pseudo-random library support type".
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Since every Allwinner USB PHY seems to be slightly different from each
other, we need to add the compatible string and the respective data
structure to make it work on the R40/V40 SoC.
Nothing spectacular this time, just one less USB controller than the H3.
Copied from the Linux kernel.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Signed-off-by: Simon Glass <sjg@chromium.org>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
If baud_divisor is not set (i.e. == -1), we should use the baud divisor
already in use for flushing the xmit register. If we don't flush the
xmit register, then SPL will hang.
Signed-off-by: Patrik Dahlström <risca@dalakolonin.se>
Fix an issue where some sections are never loaded : if p_type is
different from PT_LOAD the phdr pointer must be incremented.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Acked-by: Suman Anna <s-anna@ti.com>
Separate MAC and serdes configuration, MAC configuration must be applied
at each enetc_start() as FLR clears it.
This restores traffic for ENETC interfaces in USXGMII mode.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
lx2160a rev1 requires layerscape_gen4 device tree fixup and
lx2160a rev2 requires layerscape device tree fixup.
Add device tree fixup for lx2160a based on SoC and Version.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move streamId allocation to layerscape common device tree fixup.
Calculate streamId based on SoC variant.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add Common device tree fixup for NXP SoCs. Based on
SoC and revision call pcie_layerscape or pcie_layerscape_gen4
fixup.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The LS1028A SoC is special in the handling of the MAC addresses. We need
to write to the IERB version of the PSIPMAR0/1 register. This value will
be sampled into the corresponding port PSIPMAR0/1 register if the PCI
memory access is enabled.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Intead of setting the MAC address in enetc_start() use the proper
write_hwaddr(). U-Boot takes care of the random MAC address, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There is not any difference for disabling BARs in RC mode
between PCIe controllers with and without SRIOV.
Fixes: 80afc63fc3 ("pci: layerscape: add pci driver based on DM")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The software will still get non-zero Expansion ROM BAR size
even when the BAR_EN bit is cleared. The BAR_EN bit of
register EXP_ROM_BAR_MASK_RC is not working as expected,
so this patch changes to mask all the bits.
Fixes: 80afc63fc3 ("pci: layerscape: add pci driver based on DM")
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Passes on the primary address used by u-boot to Linux. The code does a DT
fix-up for ENETC PFs and sets the primary MAC address in IERB. The address
in IERB is restored on ENETC PCI functions at FLR.
Signed-off-by: Alex Marginean <alexandru.marginean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Read generic MMC properties from device-tree. This allows to specify for
example cd-inverted property and let MMC core to properly handle such
case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Nomadik Multi Timer Unit (MTU) provides 4 decrementing
free-running timers. It is used in ST-Ericsson Ux500 SoCs.
The driver uses the first timer to implement UCLASS_TIMER.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Add slack to the clock frequency parameters passed to firmware within
clk_set_rate. min-freq is changed to 0 and max-rate is changed to
ULONG_MAX. This fixes certain issues with pll clock rounding when the
firmware is not able to set the frequency exactly to the target, the
current implementation fails if the available frequency is even 1Hz off
the target. With the change, the firmware still tries its best to set
the frequency as close as possible to the target.
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 SoC has USB2 PHY which is similar to existing USB2 PHYs on OMAP
SoCs. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Below warning is seen when this driver is built for devices with 64 bit
physical address space.
drivers/phy/omap-usb2-phy.c: In function ‘omap_usb2_phy_probe’:
drivers/phy/omap-usb2-phy.c:187:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
priv->phy_base = (void *)base;
^
Fix this by using dev_read_addr_ptr() instead of dev_read_addr().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 has DWC3 USB controller that is very similar to other TI SoCs. Add
a new compatible to enable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
commit 29f7d05a34 ("dm: core: Move ofdata_to_platdata() call earlier")
introduces changes in the order of device_probe execution.
ofdata_to_platdata now comes before the probe function which resulted in
a deadlock and caused boot hang on AM6 devices.
Deadlock sequence: tps62360_regulator_ofdata_to_platdata --> i2c_get_chip
--> device_probe(tps62360) --> tps62360_regulator_ofdata_to_platdata
Hence convert ofdata_to_platdata to the missing probe function to fix the
hang.
Fixes: 22e8f18980 ("power: regulator: tps6236x: add support for tps6236x regulators")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add Support for writing to PHY registers for J721e. There are number of
differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY.
Create a driver_data structure with an ops and flags field and use the
flags field to indicate these differences. The differences are as
follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a
DLL_PRESENT flag to make sure that DLL related registers are accessed
only where they are present. Also add a separate set_ios_post()
callback.
2. The J721e 8 bit instance is not muxed with anything else inside the
SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is
used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in
J721e as compared to 2 bits in AM65x. Add another flag that
distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not been added
in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Cast pointers properly so as to avoid warnings when driver is built for
32 bit platforms
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
UDMA always expects 64 bit address pointer of the transfer descriptor in
the Ring. But on 32 bit cores like R5, pointer is always 32 bit in size.
Therefore copy over 32 bit pointer value to 64 bit variable before
pushing it over to the ring, so that upper 32 bits are 0s.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Exposed ring mode works well with 32 bit and 64 bit cores without need
for Proxies for 32 bit cores. Therefore switch to exposed ring mode.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fix up the debug prints that were dumping state of TCHAN RT registers to
use tchan for MEM_TO_DEV transfers.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Remove redundant coherency checks before calling cache ops in UDMA
driver. This is now handled in arch specific cache operation
implementation based on Kconfig option
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Instead of looking getting reference to SYSFW device using name which
is not guaranteed to be constant, use phandle supplied in the DT node to
get reference to SYSFW
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Flush caches when pushing an element to ring and invalidate caches when
popping an element from ring in Exposed Ring mode. Otherwise DMA
transfers don't work properly in R5 SPL (with caches enabled) where the
core is not in coherency domain.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On K3 SoCs, DMA channels are shared across multiple entities, therefore
U-Boot DMA driver needs to query resource range from centralised
resource management controller i.e SystemFirmware and use DMA channels
allocated for A72 host. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The CORE_TEMP_SENSOR_MPU register gives a raw adc value which needs to
be indexed into a lookup table to get the actual temperature. Fix the
naming and datatype of the adc value variable.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Signed-off-by: Simon Glass <sjg@chromium.org>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function related to timer and most of the timer functions are in
time.h, so move this function there.
Signed-off-by: Simon Glass <sjg@chromium.org>
These three clock functions don't use driver model and should be migrated.
In the meantime, create a new file to hold them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This patch add power domain support for Mediatek MT7622 SoCs
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
This patch fix clock-rate overflow problem in mediatek
clock driver common part.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Due to the pinctrl hardware of MT7622 is difference from others
SoC which using the common part of mediatek pinctrl.
So we need to modify the common part of mediatek pinctrl.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
If make the ref clock optional, no need refer to fixed-clock when
the ref clock is always on or comes from oscillator directly.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
No need check -ENOSYS anymore after add dummy_enable() for
fixed-clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
This is used to avoid clk_enable() return -ENOSYS.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Sometimes we may need get (optional) clock without a device,
that means use ofnode.
e.g. when the phy node has subnode, and there is no device created
for subnode, in this case, we need these new APIs to get subnode's
clock.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Add valid check for clk->dev, it's useful when get optional
clock even when the clk point is valid, but its dev will be
NULL.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
If skip all return error number, it may skip some real error cases,
so only skip the error when the clock is not provided in DTS
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
The SSUSB IP's clocks come from ssusbsys module on mt7629,
so add its driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Some features implicitly depended on MALLOC_F and OF_LIBFDT and would
fail at link-time if these features were not enabled.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Rename CONFIG_SPL_DMA_SUPPORT to CONFIG_SPL_DMA. This allows to use
macros such as CONFIG_IS_ENABLED() that allow conditional compilation of
code for SPL and U-Boot.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add i.MXRT compatible string and cpu type support to lpuart driver,
to use little endian 32 bits configurations.
Also according to RM, the Receive RX FIFO Enable (RXFE) field in LPUART
FIFO register is bit 3, so this definition should change to 0x08 as done
for i.MX8. It needs also to set baudrate the same way as i.MX8 does.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
This driver assumes that lpuart clock is already enabled before probing
but using DM only lpuart won't be automatically enabled so add
clk_enable() when probing if CONFIG_CLK is defined. If clock is not
found, because DM is not used, let's emit a warning and proceed, because
serial clock could also be already enabled by non DM code. If clock is
found but cna't be enabled then return with error.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Add PLLV3_SYS support by adding set/get_rate() for PLLV3_SYS but keeping
generic enable()/disable(). Add a different driver because ops are
different respect to GENERIC/USB.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Before set_rate() pllv3 needs enable() to power the pll up.
Add enable() taking into account different power_bit and
different powerup_set, because some pll needs its power_bit to be
set or reset to be powered on.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
div_mask is different for GENERIC and USB pll, so set it according.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Better to register the 2 clock as 2 different drivers because they work
slightly differently depending on power_bit and powerup_set bits coming
on next patches.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Remove probe function dm_scan_fdt_dev from zynqmp-firmware driver.
It is just binding its subnode zynqmp-clk.
As a result one extra node is showing up in dm tree.
This is not required, it is anyway bound from it's own zynqmp-clk driver.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hardcoded base addresses of smc controller and nand controller.
Get those addresses from dt and replace wherever they are used.
Remove smc and nand base address from header file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When two instances of AXI QSPI with flash are added and tested
simultaneously the spi driver operations are relocated twice.
As a result code is accessing addresses outside of RAM when
relocated second time which is causing a crash.
Tested on Microblaze.
Similar change was done in past by:
commit f238b3f0fb ("watchdog: dm: Support manual relocation for watchdogs")
commit 2588f2ddfd ("dm: sf: Add support for all targets which requires MANUAL_RELOC")
commit 1b4c2aa25b ("gpio: dm: Support manual relocation for gpio")
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove hardcoded base address of nand and replace it with the
value taken from device tree. Remove base address from header
file too.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Make changes to arasan nand driver to move it to driver model.
Select DM_MTD if arasan nand driver is selected.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
DS3232 is an i2c RTC with 236 bytes of battery-backed SRAM.
Add an RTC driver for DS3232 device, which provides time and
date support. Also read and write functions are provided,
which can be used to access the SRAM memory.
Signed-off-by: Nandor Han <nandor.han@vaisala.com>
This driver allows the use of i2c eeprom device or partition as backing
store for boot counter values with DM enabled.
Signed-off-by: Robert Beckett <bob.beckett@collabora.com>
Add specific dm code, but maintaining this driver as is, so more in the
shape of a mii library. Can be moved to dm in a further step.
Signed-off-by: Angelo Durgehello <angelo.dureghello@timesys.com>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
-----BEGIN PGP SIGNATURE-----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=rkHZ
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200108' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- Khadas VIM3L based on Amlogic S905D3 support
- Various fixups for amlogic boards
- Unnecessary header includes drop into video/meson
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
In the initialization of sata driver, we want to initialize all port
probes, Therefore, any detection failure between of them should continue
initialization by skipping the current port instead of exit.
Signed-off-by: Peng Ma <peng.ma@nxp.com>