Move storage device specific code into its own function instead of
calling it directly from an otherwise storage device independent
function (cl_splash_screen_prepare).
This is a preparation for supporting multiple splash locations.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Obtain 2nd NIC MAC address from baseboard EEPROM and pass it to Linux.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Implement the option to select the eeprom i2c bus when reading mac
address.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Ilya Ledvich <ilya@compulab.co.il>
Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
When passing eth address to Linux via dtb, the "local-mac-address"
property should be set for "/soc/aips-bus@02100000/ethernet@02188000",
not "/fec".
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Reset isn't instant, so delay to give it a chance. Otherwise we go on
to print a failure message before resetting anyway.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This patch adds IDE support to the MIPS Malta board. The IDE controller
is enabled after probing the PCI bus and otherwise just makes use of
U-boot generic IDE support.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Dont send always emio value as zero for zynq_gem_initialize
send it based on config.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When diffing through the changes only the relevant changes
should be displayed.
Signed-off-by: Luka Perkov <luka@openwrt.org>
Acked-by: Stefan Roese <sr@denx.de>
Add deep sleep support on Freescale LS1021QDS platform.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
[York Sun: Fix conflict in fdt.c]
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021ATWR board.
For ls1021atwr_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds LPUART support for LS1021AQDS board.
For ls1021aqds_nor_lpuart_defconfig, LPUART is used as the console.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CAAM is connected to CCI-400 S0 slave interface. Disable snooping for
S0 will cause CAAM self test failure. This patch is to enable snooping
for S0 slave interface. These CCI-400 operations are moved to
board_early_init_f() to be initialized earlier. For S4 slave interface,
issuing of snoop requests and DVM message requests are enabled.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds the CH7301 HDMI options and the common configuration
for DCU on LS1021AQDS board.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Cc: Jason Jin <Jason.Jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch reverts to use ge0_clk125 for eTSEC clock muxing. For SAI and
CAN which are pin multiplexed with RGMII1 in EC1 of RCW, ge2_clk125 will
be used via hwconfig.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
These boards are still non-generic boards.
It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
The Hyundai A7HD is a 7" 16:9 A10 powered tablet featuring 1G RAM, 8G
nand, 1024x600 IPS screen, a mini hdmi port, mini usb receptacle and a
headphones port for details see: http://linux-sunxi.org/Hyundai_A7HD
Cc: Mark Janssen <maniac@maniac.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there are some panels where the pwm input is not active low,
so make it configurable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
HDMI, SATA, USB and Ethernet appear functional, I've not done extensive tests
of all peripherals though.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Currently we've separate detailed dram settings for all sun7i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
This has been tested on a A20-Olinuxino-Lime, A20-Olinuxino_MICRO, Bananapi,
Bananapro, Cubieboard2, Cubietruck, Mele_M3 and a Linksprite_pcDuino3.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The qt840a is one of the many tv-boxes using the "i12" A20 pcb, but it
populates only one of the 2 places for a 16 bit dram ic, thus reducing
the buswidth to 16 bits, and the amount of ram to 512M, which is why we
had a separate config for it.
This commit switches the generic i12-tvbox_defconfig over to DRAM
autoconfiguration, so that it will work with the qt840a too, and drops the
qt840a specific config, like we've done with other memory-amount specific
configs before.
Tested on a generic i12-tvbox with 32 bit bus-width / 1G RAM, and on a
qt840a with 16 bit bus-width / 512M RAM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Chuwi V7 is an A10 (sun4i) based tablet with 1G of RAM, 16G of nand flash,
microsd slot, 7" 1024x768 lvds ips panel, mini hdmi out, headphones out,
stereo speakers, front & back camera and usb wifi.
It is clearly marked "CHUWI", "V7" and "Model: CW0825" on the back of the
tablet.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Hookup OTG USB controller support and enable the otg controller + USB-keyb
on various tablets.
This allows tablet owners to interact with u-boot without needing to solder
a serial console onto their tablet PCB.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD slot,
miniHDMI, 1 x MicroUSB OTG port and 1 x MicroUSB host port and
3.5mm headphone jack.
More details are available at: http://linux-sunxi.org/Gemei_G9
Signed-off-by: Priit Laes <plaes@plaes.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch add support for Marsboard A10 board.
The Marsboard A10 is a A10 based development board with 1G RAM, 1G NAND,
micro SD card slot, SATA 2.0 socket, 10/100 ethernet, mini HDMI port,
1 USB OTG port and 2 USB 2.0 ports. Board does not use the AXP209 pmic,
it does not have a pmic at all.
Board also have 2 expansion 70 pin headers.
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Convert GPIO names from Kconfig strings into pin numbers for
the 'ssd2828_config' struct. Add SSD2828 initialization between
enabling the parallel LCD interface and turning on the backlight.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
And also add Kconfig option for selecting ELDO3 voltage. The reason
for having this option is that the Android kernel sets ELDO3 to
1.2V when powering up LCD in the case if 'lcd_if' configuration
variable is set to 6 (LCD_IF_EXT_DSI) in the FEX file. Most likely
to supply power for a SSD2828 chip.
However on the MSI Primo81 tablet, which is using this particular
'lcd_if = 6' setup for LCD, setting the ELDO3 voltage appears to
be unnecessary and it works regardless. Having no schematics of
this tablet, I can only guess that 1.2V is supplied to SSD2828
in some other way.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The mk802_a10s re-uses is the "classic" mk802 case and functionality, but has
an A10s SoC inside rather then the A10, it features 512M or 1G RAM, 4G nand,
a mini-hdmi female connector, USB-A receptacle, mini-usb receptacle (OTG)
and a sdio realtek wifi chip. Unlike the original mk802 it does have a pmic,
the axp152.
For more details see: http://linux-sunxi.org/Semitime_g2
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802ii is a revised version of the mk802 A10 based hdmi tv-stick, it
features 1G RAM, 4G nand, a hdmi male connector, USB-A receptacle, 2 micro
usb receptacles (OTG & power) and USB-wifi, and does come with an axp209 pmic.
For more details see: http://linux-sunxi.org/Rikomagic_mk802ii
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The mk802 is the "classic" Allwinner A10 based hdmi tv-stick, it features
512M or 1G RAM, 4G nand, a mini-hdmi female connector, USB-A receptacle,
mini-usb receptacle (OTG) and USB-wifi. Somewhat unique the mk802 does not
use the AXP209 pmic, it does not have a pmic at all.
For more details see: http://linux-sunxi.org/Rikomagic_mk802
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
CONFIG_TARGET_FOO is only used in board/sunxi/Makefile to select the
dram config for sun5i and sun7i boards and in board/sunxi/gmac.c for some
special handling of the bananapi/bananapro (both sun7i), iow it is not used
at all on any sun4i, sun6i and sun8i boards so lets get rid of it there.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Currently we've separate detailed dram settings for all sun4i boards, this
moves them over to using auto dram configuration so that we can get rid of
all the per board dram_foo.c files.
Tested-by: Hans de Goede <hdegoede@redhat.com> on a A10-OLinuXino-Lime,
Chuwi_V7_CW0825 and ba10_tv_box
Tested-by: Zoltan HERPAI <wigyori@uid0.hu> on a pcduino
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While working on adding more boards I noticed that we lack a config for
the 512M cubieboard, and that some of the new boards which I want to add also
have 512M and 1G variants, rather then adding 2 defconfig's for all of these,
lets switch the exising boards which have both a 512M and 1024M variant over
to the sun4i dram autoconfig code.
This also drops the foo_RAMSIZE_defconfig variants of boards where we currently
have 2 separate configs already.
Note:
1) The newly introduced CONFIG_DRAM_EMR1 kconfig value is not used with
a value other then its default for now, but we need this to be configurable
to support some new boards with auto dram config.
2) We always set all CONFIG_DRAM_foo values in defconfigs, even if they match
the defaults, this is done to make it more clear what values are used for a
certain board.
This has been tested on a Mele A1000, Mini-X and a Cubieboard, all 1G
variants, the dram autoconfig code has also been tested on a 512M mk802
(a defconfig for the mk802 is added in a later patch).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
While running some tests with an Olinuxino-A13-Micro + a 7" Olimex LCD module
I noticed that the screen flickered. This is caused by the lcd display clk
phase reg value being set to 0, where it should be 1 in this setup.
This commit adds a Kconfig option for the lcd display clk phase, so that we
can set it per board. This defaults to 1, because looking at all the fex
files in sunxi-boards, that is by far the most used value.
This commit updated the Ippo and MSI Primo73 tablet defconfigs to override the
default of 1 with 0, as that is the correct value for those tablets, this
keeps the register settings the same as before this commit.
The Olinuxino-A13 defconfigs are not updated, changing the register setting
for these boards from 0 to 1, this is intentional.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
To support different ddr3 memory sizes we should start using
imx_ddr_size(..) instead of the define PHYS_SDRAM_SIZE.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This patch configures and initializes the L2 switch on T1040rdb board.
The external L2 switch ports may be connected to PHYs only over
QSGMII, for T1040rdb.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
This patch configures and initializes the L2 switch on T1040QDS board.
The L2 switch ports must be initialized according to the SerDes
protocols.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's T1040qds board may be configured to have up to
5 FMAN ports (FM1@DTSEC1 to FM1@DTSEC5). From these 5 ports,
2 of them may be fixed-links (FM1@DTSEC1 annd FM1@DTSEC2),
connected to other two ports from an intergrated
VSC9953 L2 Switch (switch ports 8 and 9). These fixed-link
ports have no PHYs attatched, so they don't have a
corresponding MDIO.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stefano Babic <sbabic@denx.de>
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
- corvus board fix problems with toshiba nand chips
on the corvus board problems with toshiba chips
Manufacturer ID: 0x98 Chip ID: 0xdc encounterd.
Solve this in the following way:
- set other nand timings
- enable CONFIG_SYS_NAND_READY_PIN
- correct the MACH_TYPE setting
Signed-off-by: Heiko Schocher <hs@denx.de>
if in SPL mode recovery button is pressed, erase also spi flash
from offset 0 to CONFIG_SYS_NAND_U_BOOT_SIZE on the taurus board.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the new Barco platinum platform. It currently
includes those two boards:
platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.
platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
Since commit 1f98e31bc0 ("imx: mx6sxsabresd: Use the pfuze common init
function") board_late_init() became empty, so we can safely remove this unneeded
function.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB-PB board adds 2.5G SGMII support with AQR105 PHY.
rcw_0x095 is used for 10G XFI + 3x PCIex1
rcw_0x135 is used for 2.5G SGMII + 2x PCIex1
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
A new deep sleep interface is introduced to support generic
board structure. Converts it to use new interface.
Besides, added SPI/SD/NAND boot deep sleep support.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Secure boot target is added for T1042RDB platform.
Signed-off-by: Gaurav Rana <gaurav.rana@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes 2 protocol 56 is not valid any longer due to
the new RCW; protocol 55 is used instead, so add
SerDes 2 protocol 55 to align with RCW.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR and SPI flash secure boot target for C29XPCIE board.
Signed-off-by: Po Liu <Po.Liu@freescale.com>
Signed-off-by: Mingkai.Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Both ARCangel4 and AXS10x are FPGA-based boards so they may have
different CPUs. For now we have only 1 option (ARC700) and we define
this as default in arch Kconfig.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The external DAC for VGA output might have either a power or reset
control pin that needs to be pulled up, as is the case on the
Hummingbird A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Using an external DAC for VGA output was available on sun5i. Since
some other SoCs don't have a builtin TV encoder, but might have
use for a VGA output, enable the option for the platforms that
don't have TV encoders.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for a sun4i board built by Linksprite. This addition covers
both v1 and v2 versions. As the board has been working with 408MHz memory
setting in the u-boot-sunxi branch, and has been proven to be running stable
during my tests as well, a respective new DRAM config file is added as well.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for external DACs connected to the parallel LCD interface driving
a VGA connector, such as found on the Olimex A13 boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A23 (sun8i) only has lcd output support, so allow building the video code
without HDMI support for use with the A23.
Also the A23 has the same reset bits (and necessity to enable the DRC block)
as the sun6i, so enable those bits for sun8i too.
Note building without HDMI support is useful for the A13 (sun5i variant) too,
as that one does not have HDMI either.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the new Bananapro A20 development board from lemaker.org.
This board features 1G RAM, 2 USB A receptacles, 1 micro USB receptacle for
OTG, 1 micro USB receptacle for power, HDMI, sata, Gbit ethernet, ir receiver,
3.5 mm jack for a/v out, on board microphone, 40 gpio pins and sdio wifi.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This patch uses the same DRAM settings as in the pre-installed
Android firmware. The LCD display is supported too.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This patch uses the same ZQ and DRAM clock settings as in the
pre-installed Android firmware.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The CONFIG_UART0_PORT_F option has been supported since
http://git.denx.de/?p=u-boot.git;a=commit;h=ff2b47f6a9cc1025
This option is primarily useful only for low level u-boot debugging
on tablets, where normal UART0 is difficult to access and requires
device disassembly and/or soldering.
This patch now allows it to be selected from menuconfig. A dependency on
SPL_FEL is added because u-boot does not support booting from NAND yet
and also booting from SD card is impossible when a MicroSD breakout board
is plugged into the SD slot.
Additionally a compilation problem is fixed:
common/spl/built-in.o: In function `spl_mmc_load_image':
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:94: undefined reference to `mmc_initialize'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:96: undefined reference to `find_mmc_device'
/tmp/u-boot-sunxi/common/spl/spl_mmc.c:104: undefined reference to `mmc_init'
scripts/Makefile.spl:206: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
We need separate defconfigs for the v5 and v1.2 versions of this board, as
they use different DRAM parameters.
Note they also use different dtb files, as the wifi is different too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
dcdc4 is not used on sun8i, disable it.
While at it also add comments to the other fixed voltages to document what
they are used for.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Explicitly turn off unused voltages, rather then leaving them as is. Likewise
explictly enabled the dcdc convertors, rather then assuming they are already
enabled at boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The dcdc1 voltage is typically used as generic 3.3V IO voltage for things like
GPIO-s, sdcard interfaces, etc. On most boards this is undervolted to 3.0V to
safe battery, but not on all, make it configurable so that we can use the
same settings as the original firmware on all boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The Merrii Hummingbird A31 is a A31 based development board with 1G
RAM, 8G NAND, AP6210 WiFi+BT, gigabit ethernet, USB OTG, 2 USB 2.0
ports connected to a USB hub chip, HDMI, VGA, TV and stereo in/out.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.
This makes our MAC address generation code also work on sun6i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.
Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
AM43xx Industrial Development Kit is a new board
based on AM437x line of SoCs. Targetted at Industrial
Automation applications, it comes with EtherCAT, motor
control and other goodies.
Thanks to James Doublesin for all the help.
Cc: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure that all OPPs are checked on
scale_vcores(). While at that also fix 600MHz
VDD_MPU voltage according to AM437x Data Manual
available at [1].
Table 5-3 on that document, lists all valid
voltages per frequency.
[1] http://www.ti.com/lit/ds/symlink/am4379.pdf
Signed-off-by: Felipe Balbi <balbi@ti.com>
The frequencies for 25MHz in dpll_per were out of spec for 25MHz,
correct.
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Need to provide PLL values for all possible input frequencies (19.2, 24,
25, 26MHz). Values provide are also optimized for jitter (needed
especially for PER PLL and DDR PLL).
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Tested-by: Mugunthan V N <mugunthanvnm@ti.com>
cros_ec_board_init() should be called only when CONFIG_CROS_EC is
enabled.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.
Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.
To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since we already swtiched to use the new mechanism for building
U-Boot for coreboot, coreboot.h is no longer needed so remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_CAR_ADDR and CONFIG_SYS_CAR_SIZE to Kconfig so that
we don't need them in the board configuration file thus the same
board configuratoin file can be used to build both coreboot version
and bare version.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
In theory U-Boot built for coreboot is supposed to run as a payload
to be loaded by coreboot on every board that coreboot supports.
The U-Boot build process uses SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE
which are hardcoded in board defconfig and Kconfig files. For better
support of coreboot, we want to make these two options configurable
so that we can easily change them during 'make menuconfig' so that
the generated U-Boot image for coreboot is board configuration aware.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert CONFIG_X86_RESET_VECTOR and CONFIG_SYS_X86_START16 to Kconfig
options so that we can remove them from board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Since commit 41623c91b0 u-boot running in qemu is
crashing in function do_omap3_emu_romcode_call(). RX-51 board uses this function
for Cortex-A8 errata 430973 workaround (Set IBE bit in ACR) which is needed only
on real secure device and not in qemu.
This board patch just disable calling secure PPA routine on non secure devices.
Qemu implements GP device and with this patch u-boot is working in qemu again.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
- "string" type for SYS_* is defined in arch/Kconfig
- SYS_CPU "armv7" has been replaced with "select CPU_V7"
- SYS_SOC "tegra124" is already defined in tegra124/Kconfig
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
Part of DMM logic is reuse from commit
47a4bea6af ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).
So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3a ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.
Signed-off-by: Nishanth Menon <nm@ti.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
Add spi nor boot support for mx6slevk board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Configure the pad setting and enable qspi clock to support qspi
flashes access.
Add QSPI related macro in configuration header file.
Note:
mx6sxsabresd Revb board, 32M flash is used, but in header file,
CONFIG_SPI_FLASH_BAR is not defined, and we still use SZ_16M.
The LUT initialization qspi_set_lut function uses 32BIT addr,
however CONFIG_SPI_FLASH_BAR and 24BIT addr should be used to
access bigger than 16MB size flash, and BRRD/BRWR should also
be supported. Future patches will fix this.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
get_board_rev() just returns the cpu revision, which does not make it really
useful for distinguishing between revisions of the board.
Let's get rid of get_board_rev() as it is not being used with its correct
meaning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Repair the register configuration and add proper support for the
display attached to both LVDS channels.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Pull all of the video handling into a separate file, since a lot
more code will be added and such code would polute the board file.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Pull the definitions of GPIOs into a separate header file, so that
they can be used across all source files.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Just zap multiple spaces and replace them with tabs properly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Create a fake model table entry with default values, so we can error
check the board rev value once when querying it from the firmware, rather
than error-checking for invalid board rev values every time the model
table is used.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Add a board rev entry for the new model A+, and augment the board
rev error handling code to be a bit more verbose.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Model A and CM RPis don't have an on-board USB Ethernet device. Hence,
there's no point setting $usbethaddr based on the device fuses. Use the
model detection code to gate this. Note that the fuses are actually
programmed even on those devices though.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
As agreed with Steve Rae I'm taking over maintenance of the
semihosted, emulated FVP/foundation model Versatile Express
64 bit board variant.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Steve Rae <srae@broadcom.com>
Since commit 4a271cb1b4 (exynos: usb: Switch USB VBUS GPIOs to be
device tree configured) it's not needed for the board specific files to
turn on the VBUS GPIO by hand as that gets done based on device tree. So
drop the redundant code from the SMDK5420 board file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.
As a side-effect move the parade functions from the exynos system header
file to its own file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for Odroid-XU3.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The weak mxs_adjust_memory_params function is called from spl_mem_init.c,
so it must be linked into the SPL to have an effect. Move it from
mx23_olinuxino.c to spl_boot.c.
This change was verified by reading back the register values.
Signed-off-by: Jan Luebbe <jlu@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Otherwise NAND booting is likely to fail. Since this disables the NAND related
clocks and SPL can't load the main U-Boot from NAND.
This problem was introduced with this patch:
e25fbe3f (gw_ventana: Move the DCD settings to spl code)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
We don't have driver for the Intel Topcliff PCH Gigabit Ethernet
controller for now, so enable the Intle E1000 NIC support, which
can be plugged into any PCIe slot on the Crown Bay board.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.
Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PCIe bus on Cardhu is routed to the dock connector. An ethernet NIC
is available on the dock over the PCIe bus. Enable the PCIe controller
and the network device driver so that the device can boot over the
network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add proper error checking into the PHY tuning patch. Make the PHY tunning only
happen in case the KSZ9021 PHY is enabled in config. Call the config callback
after the tuning finished.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Tom Rini <trini@ti.com>
Cc: Pavel Machek <pavel@denx.de>
A new interface is introduced to support generic board structure.
Converts it to use new interface.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently the ROM_SIZE is hardcoded to 8MB in arch/x86/Kconfig. This
will not be the case when adding additional board support. Hence we
make ROM_SIZE configurable (512KB/1MB/2MB/4MB/8MB/16MB) and have the
board Kconfig file select the default ROM_SIZE.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
Adjust the configuration to use the driver model version of the pl01x
serial driver. Add the required platform data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
With the introducing of generic board and ARM-based cores, current
deep sleep framework doesn't work anymore.
This patch will convert the current framework to adapt this change.
Basically it does:
1. Converts all the Freescale's DDR driver to support deep sleep.
2. Added basic framework support for ARM-based and PPC-based
cores separately.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Freescale LS1021AQDS share some pins, so Add the hwconfig option
that allows the user to choose which the function he wants.
The main pin mux IP is:
eSDHC, SAI, IIC2, RGMII, CAN, SAI.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021ATWR board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Chen Lu <chen.lu@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Through adding CONFIG_QIXIS_I2C_ACCESS macro,
QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used
for both i2c and ifc access to QIXIS FPGA. This is
more convenient for coding.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When resuming from deep sleep, the I2C channel may not be
in the default channel. So, switch to the default channel
before accessing DDR SPD.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Alt board has been connected to eMMC of 8GB to MMC port.
This enables MMC port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lager board has been connected to eMMC of 8GB to MMC1 port.
This enables MMC1 port and MMC command.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Set the PHY skew settings for the ethernet phy on the SOCFPGA Cyclone5
hardware.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Wolfgang Denk <wd@denx.de>
BRDCFG1_EMI1_SEL_MASK has been changed to 0x78, which contains
selection bits and connected status bit. So the Corresponding mux
value of RGMII is changed to BRDCFG1_EMI1_SEL_RGMII | BRDCFG1_EMI1_EN.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The new device trees use a more generic interface for
supporting muxing mdio buses. The mux property is thus
specified in "reg", rather than "fsl,hydra-mdio-muxval".
In order to support using old device trees, we keep the
old fixup in there. Linux will therefore see the both
properties, but will ignore fsl,hydra-mdio-muxval.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add multiplexing support among SPI flash, TDM riser card and SDXC.
it routes SPI pins to SPI flash by default.
Route SPI pins to SD slot if "adaptor=sdxc" is set in hwconfig.
Route SPI pins to TDM riser card and do fixup for dts if "pin_mux=tdm"
is set in hwconfig.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Xie Xiaobo <X.Xie@freescale.com>
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.1 requires different MEM_PLL_RAT from previous v1.0,
and also update core frequency to 1.8GHz for v1.1.
We reserve the support for T2080 v1.0 and enable v1.1 by default.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In B4860QDS board SerDes2 lanes EFGH either go to SFP or AMC riser card
slot2 so either DTSEC3/DTSEC4 or TGEC1/TGEC2 should be accessible. This
Patch enables DTSEC3/DTSEC4 or TGEC1/TGEC2 on bases of user specified
string fsl_b4860_serdes2:sfp_amc=amc or fsl_b4860_serdes2:sfp_amc=sfp
respectively in hwconfig.
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SerDes2 lanes EFGH either go to SFP or AMC riser card slot2.
By default AMC will be configured even if no hwconfig is specified.
To enable XFI via SFP use the below hwconfig:
fsl_b4860_serdes2:sfp_amc=sfp
Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@ffeescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since xfi has no phy, we delete the property "phy-handle" and use
a "fixed-link" property for a xfi port.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We need following changes to make xfi work on B4:
1. set cross-point switch VSC3308 to use sfp config when running xfi;
2. add 10G interface check for xfi;
3. set phy address for xfi so the 10G ports can be registered by mdio;
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add the support of newly added LC VCO SerDes protocols
for configuration of IDT and VSC crossbar
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
B4860, B4440, B4420 and B4220 have MAPLE, so enable law creation
for them only. Remove static LAW creation for MAPLE.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
cppcheck reports:
[board/muas3001/muas3001.c:270]: (error) Uninitialized variable: psize
remove the CONFIG_SYS_RAMBOOT define to prevent this error report.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
This define is never set in our setup, so we can remove it safely. The
former code causes cppcheck to complain about:
[board/keymile/km82xx/km82xx.c:311]: (error) Uninitialized variable:
psize
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Wolfgang Denk <wd@denx.de>
Reviewed-by: York Sun <yorksun@freescale.com>
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
Signed-off-by: Ying Zhang <b40530@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Adjust timing for dual-rank UDIMM, verified on M3CQ-8GHS3C0E for speed of
1066, 1333, 1600, 1866MT/s. The 1866 timing is copied to 2133 timing in
case such DIMM comes available.
Also update single-rank 1866 timing. Enable interactive debugging as well.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
add FIT support and set "boardid" from factoryset records
"DEV/id" and "COMP/ver". "boardid" is used for selecting
which fit configuration gets booted on the board.
Signed-off-by: Heiko Schocher <hs@denx.de>
a record could contain other records, so after an ">" (begin mark)
there not always come an end mark "<", instead a ">" is possible.
Take care of this.
Signed-off-by: Heiko Schocher <hs@denx.de>
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.
Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Boards using the TWL4030 regulator may not all use the LDOs the same way
(e.g. MMC2 power can be controlled by another LDO than VMMC2).
This delegates TWL4030 MMC power initializations to board-specific functions,
that may still call twl4030_power_mmc_init for the default behavior.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Fix omap3_evm warning, add twl4030.h]
Signed-off-by: Tom Rini <trini@ti.com>
The arch_preboot_os function used in boards using R-Car ARM SoC (r8a7790,
r8a7791, r8a7793 and r8a7794) is common.
This makes rcar-gen2-common/common.c file providing common function for
R-Car ARM SoC, and moves this function to this file.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Control macro of mstp is common in R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794). This moves these to arch-rmobile/rcar-mstp.h
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Module control registers of R-Car ARM SoC (r8a7790, r8a7791, r8a7793 and
r8a7794) are same address. This moves these to header file of SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Out of all OMAP5-like boards, only one of them
needs CONFIG_MISC_INIT_R, so it's best to enable
that for that particular board only, instead of
enabling for all boards unconditionally.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This function is not needed. Remove it to improve the generic init sequence
slightly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Old kernels cannot handle booting in non-secure (hyp) mode, so when
OLD_SUNXI_KERNEL_COMPAT is set, also set ARMV7_BOOT_SEC_DEFAULT.
Note that whether to booting secure or non-secure can always be overriden
using the bootm_boot_mode environment variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
If the target power is connected through a gpio, then give the target some
time to power up before continuing with ahci / sata probing, this avoids
link timeouts, without penalizing other boards where there is no target
power gpio.
Why 500 ms ? I started with 200, that was not enough, then I went to 500 which
worked, lowering it to 350 broke things again, so 500 seems the minimum my
vertex2 needs to be ready to get probed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add simplefb support, note this depends on the kernel having support for
the clocks property which has recently been added to the simplefb devicetree
binding.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Use pre-populated simplefb node under /chosen as
disussed on the devicetree list]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>.
This adds a fixed mode hdmi driver for the sunxi platform. The fixed
mode is a relatively safe 1024x768, more complete EDID handling is
currently not provided. Only HDMI is supported today.
This code is enabled when HPD detects an attached monitor.
Current config is such that 8MB is shaved off at the top of the RAM.
This avoids several memory handling issues, most significant is the fact
that on linux on ARM you are not allowed to remap known RAM as IO. A
clued in display driver will be able to recycle this reserved RAM in
future though.
cfbconsole was chosen as it provides the most important functionality: a
working u-boot console, allowing for the debugging of certain issues
without the need for a UART.
Signed-off-by: Luc Verhaegen <libv@skynet.be>
[hdegoede@redhat.com: Major cleanups and some small bugfixes]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
EC1 pins in RCW can be selected as RGMII1, GPIO3, CAN1/2, FTM1 or
SAI1/2. There is a bug that EC3 RGMII could not work when selecting EC1
as other functionality except RGMII. The workaround is to select
ge2_clk125 for eTSEC clock muxing in register SCFG_ETSECCMCR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SystemID information could be read through I2C1 from EEPROM
on LS1021ATWR board.
As LS1 is a little-endian processor, getting the version ID by
be32_to_cpu() is wrong. Fix it by using e.version directly.
This change will be compatible for both ARM and PowerPC.
As there is an errata that I2C1 could not work in SD boot,
reading EEPROM through I2C1 is disabled too in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>