The rtl8139 driver is derived from Etherboot driver, which is in
turn derived from Linux 8139too driver added in Linux 2.2.18pre14.
An undocumented change in Linux 2.4.10.2 added a new field to the
driver, MODULE_LICENSE("GPL"); . According to current Linux kernel
licensing rules, Documentation/process/license-rules.rst, quote:
"GPL" Module is licensed under GPL version 2. This
does not express any distinction between
GPL-2.0-only or GPL-2.0-or-later. The exact
license information can only be determined
via the license information in the
corresponding source files.
And since the code does not contain any "future" clause, the tag
is therefore GPL-2.0 only.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Just move functions around in preparation for easy DM conversion,
rename rtl_bcast_addr() to rtl8139_bcast_addr(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Finish the checkpatch cleanup of the driver, fix the remaining issues
in probe and init function and in global variables, rename the probe
function to rtl8139_init(), no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This hardware reset and reset-wait implementation was twice in the
driver, factor it out into a separate function. This really should
use wait_for_bit() eventually and return -ETIMEDOUT, but thus far,
handling of any of this is missing from the driver. This must be
added later. Thus far, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_stop(), clean up checkpatch errors in
the stop polling function. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_recv(), clean up various checkpatch errors,
line-over-80 conditions, and malformed comments. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_send(), clean up the TX polling, the TX
OK condition at the end, overuse of typecasts, and various line-over-80
problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_reset(), clean up the reset polling
and various line-over-80 problems. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_set_rx_mode(), use unsigned variables
where applicable and inline mc_filter[] values. No functional chanage.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
This string of macros is exactly the same thing as rtl8139_rx_config,
so just use rtl8139_rx_config. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename the function to rtl8139_read_eeprom() to keep the naming
consistent, keep the variables sorted in reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The macro assumes ee_addr variable to be present when it's being
used. Rework the macro into a function instead and pass it an
argument specifying the register base address, to make it future
proof for DM conversion.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the horrible register definitions in the RTL8139 driver.
This does create a couple of checkpatch errors, but the driver is
full of them anyway, and those will be cleaned up later.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The DMA may attempt to write a DMA descriptor in the ring while it is
being updated. By writing the DMA descriptor buffer address to 0, it
is assured the DMA will not use such a buffer and the buffer can be
updated without any interference.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This patch prevents an issue where the RX packet might have been
accessed by the CPU, which now has cached data from the packet in
the caches and possibly various write buffers, and these data may
be evicted from the caches into the DRAM while the buffer is also
written by the DMA.
By invalidating the buffer after the CPU accessed it and before the
DMA populates the buffer, it is assured that the buffer will not be
corrupted.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The current code polls the RX desciptor ring for new packets by reading
the RX descriptor status. This works by accident, as the RX descriptors
are often in non-cacheable memory. However, the driver does support use
of RX descriptors in cacheable memory.
This patch adds a missing RX descriptor invalidation, which assures the
CPU will read a fresh copy of the RX descriptor instead of a cached one.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Currently the code only flushes the first RX descriptor, not every entry
in the RX descriptor ring. Fix this, to make sure the DMA engine can pick
the RX descriptors correctly.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
This code programs the next descriptor in the TX descriptor ring into
the hardware as the last valid TX descriptor. The problem is that if
the currenty descriptor is the last one in the array, the code will
not wrap around correctly and use TX descriptor 0 again, but instead
will use TX descriptor at address right past the TX descriptor ring,
which is the first descriptor in the RX ring.
Fix this by adding the necessary wrap-around.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
The RX descriptor field 3 should contain only OWN and BUF1V bits before
being used for receiving data by the DMA engine. However, right now, if
the descriptor was already used for receiving data and is being cleared,
the field 3 is only modified and the aforementioned two bits are ORRed
into the field. This could lead to a residual dirty bits being left in
the field 3 from previous transfer, and it generally does. Fully set the
field 3 instead to clear those residual dirty bits.
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Stephen Warren <swarren@nvidia.com>
Replace the adhoc debugging ifdeffery with debug_cond() and an
internal SROM_DEBUG macro to select the debug level.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Move the functions in the driver around to better fit future DM
conversion, drop function forward declarations. No functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Rename these functions to dc2114x_{inl,outl}(), use u32 values in
them instead of plain signed integers as all those values are in
fact register values and the driver code does bitwise operations
on them. No functional change intended.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace these macros with static functions to permit the compiler to
do type checking on the functions. The INL()/OUTL() functions have to
be moved in this patch as well, as those DE4X5 macros are using them.
No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the remaining driver code, macro space alignment, function
declaration indent, replace __attribute__((aligned(32))) with plain
__aligned(32). No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the SROM accessors to bring them up to standards with
U-Boot coding style. Sort variable into reverse xmas tree. No
functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the send_setup_frame() to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver halt code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver recv code to bring it up to standards with
U-Boot coding style. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver send code to bring it up to standards with
U-Boot coding style, invert the loops where applicable to cut
down the level of indent. No functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Clean up the driver init code to bring it up to standards with
U-Boot coding style, no functional change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace the PCI IO access with PCI memory access, the card
supports both, but the former does not work with QEMU SH4.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Replace mips-specific UNCACHED_SDRAM() macro with standard
map_physmem(), which permits the driver to work on other
systems than mips.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros are not used by any board, remove them to simplify
the driver. The EEPROM accessors are still retained however, as
those might still be useful.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
These macros guard one switch-case statement, which grows mips malta
by some 20 bytes if debug is enabled, and even less if it is not. To
make the code simpler, just support all the NICs and be done with it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Due to v5.7-rc1 sync the SD controller nodes in rk3399.dtsi
have HCLK_SD assigned-clocks which are usually required for
Linux and don't require to handle them in U-Boot.
assigned-clocks = <&cru HCLK_SD>;
So, mark them as empty in clock otherwise device probe on
those SD controllers would fail.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The guessed reason is that the existing logic of filling
tx fifo with data, rx fifo with NULL for tx transfer and
filling rx fifo with data, tx fifo with NULL for rx transfer
is not clear enough to support the Quad Page Program.
SiFive SPI controllers have specific sets of watermark
registers and SPI I/O directions bits in order to program
SPI controllers clear enough to support all sets of operating
modes.
Here is the exact programing sequence that would follow on this
patch and tested via SPI-NOR and MMC_SPI.
- set the frame format proto, endian
- set the frame format dir, set it for tx and clear it for rx
- TX transfer:
fill tx fifo with data.
wait for TX watermark bit to clear.
- RX transfer:
fill tx fifo with 0xff.
write nbytes to rx watermark register
wait for rx watermark bit to clear.
read the rx fifo data.
So, this patch adopts this program sequence and fixes the existing
I/O direction bit.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller has a proto bit field in frame format
register which would be used to configure the SPI I/O protocol
lines used on specific transfer.
Right now the driver is configuring this proto using slave->mode,
for all types of transctions. This makes the driver unable to
function since the proto needs to configure dynamically for
each and every transaction separately at runtime.
Now, the controller driver supports per transfer via spi-mem
exec_opo, so add the fmt_proto flag and fill the per transfer
buswidth so that the controller configures the proto bit at
runtime.
This patch fixes the SPI controller works with SPI NOR flash
on quad read with page program.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
SiFive SPI controller is responsible to handle the
slave devices like mmc spi and spi nor flash.
The controller is designed such a way that it would
handle the slave transactions based on the I/O protocol
numbers, example if spi nor slave send quad write opcode
it has to send alone with I/O protocol number of 4 and
if it try to send data it has to send I/O protocol number
along with 4 line data.
But the current spi-xfer code from spi-mem is combining
the opcode and address in a single transaction, so the
SPI controller will be unable to identify the I/O protocol
number of opcode vs address.
So, add the spi-mem exec_op with spi-xfer of opcode, address
and data as a separate transaction. This doesn't remove
the .xfer of dm_spi_ops since mmc spi will make use of it.
Note: This code might have moved to the spi-mem core area
once we have done the dedicated tests on other controllers
and have real reason to move.
Cc: Vignesh R <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Spansion "s25fs512s" flash is incorrectly decoded as "s25fl512s" on
various platforms as former is not present. Add the entry.
Linux already has both the flashes present. A snippet below:
{ "s25fl512s", INFO6(0x010220, 0x4d0080, 256 * 1024, 256...},
{ "s25fs512s", INFO6(0x010220, 0x4d0081, 256 * 1024, 256...},
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Enable designware watchdog driver for rk3399 if WDT defined.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
IS25WP256 flash chips do support 4byte address opcodes,
so enable support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Sagar Kadam <sagar.kadam@sifive.com>
Enable QE bit for ISSI flash chips.
QE enablement logic is similar to what Macronix
has, so reuse the existing code itself.
Cc: Sagar Shrikant Kadam <sagar.kadam@sifive.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Usually variable name slave is used for spi_slave structure
and slave_plat for the dm_spi_slave_platdata.
Let's follow this meaningful notation by replacing slave
with slave_plat for dm_spi_slave_platdata structure.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Add DM_ETH support for DPAA1, DPAA2 based RDB platforms: ls1046ardb,
ls1043ardb, lx2160ardb, ls2088ardb, ls1088ardb.
- Add GICv3 support for ls1028a, ls2088a, ls1088a.
- Add lpuart support on ls1028aqds.
- Few bug fixes and updates on ls2088a, ls1012a, ls1046a, ls1021a based
platforms.
When U-Boot is not the first-stage bootloader we don't want to
re-configure the PCI devices, since this has already been done. Add a
check to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
A device may want to write out ACPI tables to describe itself to Linux.
Add a method to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Probe the FMan MACs based on the device tree while
retaining the legacy code/functionality.
One notable change introduced here is that, for DM_ETH,
the name of the interfaces is corrected to the fmX-macY
format, that avoids the referral to the MAC block names
which were incorrect for FMan v3 devices (i.e. DTSEC,
TGEC) and had weird formatting (i.e. FM1@DTSEC6, FM1@TGEC1).
The legacy code is left unchanged in this respect.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Allow the MDIO devices to be probed based on the device tree.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Move the receive buffer free code in a separate function.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make any adjustments necessary in order to support DPAA2 devices probed
using CONFIG_DM_ETH. While at it, fixup some styling issues aroung the
switch-case statement.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
When CONFIG_DM_ETH is enabled DPAA2 network interfaces will now probe
based on DTS nodes with the "fsl,qoriq-mc-dpmac" compatible.
In this case, transform the ldpaa_eth driver into a UCLASS_ETH driver
and reuse the _open()/_tx()/_stop() functions already inplemented.
For the moment, the ldpaa_eth driver will support both configurations:
with or without CONFIG_DM_ETH enabled. Any 'struct eth_device' occurrence
now has a matching 'struct udevice' made mutually exclusive based on the
state of CONFIG_DM_ETH.
Signed-off-by: Florin Laurentiu Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the MDIO interface integrated in the mEMAC (Multi-rate
Ethernet Media Access Controller) and the Fman 10G Ethernet MACs.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a driver for the rng device found on rockchip platforms.
Support rng module of crypto v1 and crypto v2.
Signed-off-by: Lin Jinhan <troy.lin@rock-chips.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit: 0ebb261a0b2d ("spi: spi-mem: Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum")
in linux.
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
This also fixes a bug identified with the atmel-quaspi driver.
The spi-nor core, when erasing sectors, fills the spi_mem_op template
using SPI_MEM_OP_NO_DATA, which initializes all the data members with
value zero. This is wrong because data.dir is treated as SPI_MEM_DATA_IN,
which translates in our driver to read accesses for erases (RICR), while
the controller expects write accesses (WICR).
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Linux has good support for Toshiba SPI-NAND, so lets import it.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Luka Kovacic <luka.kovacic@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The s25fl256s0 supports dual and quad read like s25fl256s1.
Enable it by adding SPI_NOR_DUAL_READ and SPI_NOR_QUAD_READ
flags to the flash_info entry.
Tested on real silicon and confirmed to be working.
Signed-off-by: Bacem Daassi <Bacem.Daassi@cypress.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
"assigned-clock-parents" and "assigned-clock-rates" DT properties take
effect only after ofdata_to_platdata() when clk_set_defaults() is called
in device_probe(). Therefore clk get rate() would return a wrong value
in ofdata_to_platdata() when compared with probe. Hence it needs to be
moved to probe.
Tested on u-boot-ti/next.
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
hweight32 is a somewhat expensive way to check for power-of-2. Use the
is_power_of_2 helper, which does the standard and cheap idiom
foo&(foo-1)==0.
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-96 (-96)
Function old new delta
spi_nor_write 388 292 -96
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
To support the SPI MEM API, instead of modifying the existing U-Boot
driver, this patch adds a port of the existing Linux driver.
This also has the advantage that porting changes and fixes from Linux will
be easier.
Porting of driver left most of the functions unchanged while few of the
changes are:
-Remove lock(mutexes) and irq handler as u-boot is a single core execution.
-Remove invalid masterid as it was required specially for multicore
execution in LS2088ARDB which is not the case in u-boot.
-Remove clock support as changing spi speed is not supported in uboot and
nor in linux.
Currently tested on LS1088ARDB, LS1012ARDB, LS1046ARDB, LS1046AFRWY,
LS1043AQDS, LS1021ATWR, LS2088ARDB, I.MX6ULL EVK.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
-----BEGIN PGP SIGNATURE-----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=e10O
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200428' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix sd-emmc controller A init on G12A/G12B/SM1 SoCs
- add GXBB USB PHY driver
- enable access to SPI NOR Flash on VIM2 and VIM3/VIM3L boards
- fix USB PHYs Power-Up on on VIM3/VIM3L boards
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use ofnode_ or dev_ APIs instead of fdt_ and fdtdec_ APIs so that the
driver can support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use ofnode_decode_display_timing() instead of
fdtdec_decode_display_timing() to parse display timing, so that we can
support live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Power on/off the PHYs to enable power to the USB ports, fixing USB support
on Khadas VIM3/VIM3L boards.
The G12A USB complex has at least 2 USB2 PHYs, but one is muxed between the
DWC2 and DWC3 controller and the other one directly connected to the DWC3
controller. The USB3+PCIe combo PHY is muxed between the DWC3 controller
and a DW-PCIE controller.
All PHYs are optional, but it's type (usb2/usb3) and position are important
to determine it's capabilities, thus they are stored in a fixed size
array and the phy-name determines it's position, it's position determining
it's type and functionnalities.
This is why we need to loop over the array to power on all the DT provided
PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This adds support for the USB PHY found on Amlogic GXBB SoCs.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add missing SD_EMMC_A controller gates needed for probe of the A
controller, otherwise leading to a freeze of the SoC after b3d69aa596.
Fixes: b3d69aa596 ("clk: meson: reset mmc clock on probe")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
-----BEGIN PGP SIGNATURE-----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=2jL1
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2020-04-27' of https://gitlab.denx.de/u-boot/custodians/u-boot-mips
- brcmnand: fix missing code path from Linux driver
- bmips: fix build error when disabling USB
- mips: add option to restore original exception vector base
- mips: fix off-by-one error when clearing gd_data
- mips: minor fixes for compatibility with generic SPL framework
- spl: refactor legacy image loading
- spl: add LZMA decompression support for legacy images
- Makefile: add target to build LZMA compressed U-Boot images
- mtmips: refactor and rewrite low-level init code
- mtmips: add and enable SPL support with LZMA
- mtmips: add support for MT7628 reference board
- mtmips: add support for VoCore/VoCore2 board
Here we introduce new development platfrom for ARC: HSDK 4xD.
That's pretty much the same base-board as in HSDK but with
very recent quad-core ARC HS47D in the ASIC.
Thus we try to re-use existing code as much as possible while
inevitably add some pieces needed for the new ASIC.
Also we drop selection of bounce buffers on AXS10x
as there's no use of them any longer.
Some chips provide their sysreset function in reset controller, which is
normally a bit written to 1 to perform the sysreset.
This patch adds a new sysreset driver to take advantage of it.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Linux Broadcom NAND driver only disabled clock if no childs are initialized.
This section of the code seems to have been accidentally dropped when it was
imported in U-Boot.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The end_cmd field in the variables cmd_phase_addr and data_phase_addr
contains the value 0xFF when the end_cmd equals NAND_CMD_NONE. This
should be 0x00.
This is caused by comparing NAND_CMD_NONE (int) with end_cmd (u8).
end_cmd will be promoted by the int value -1 and therefore is not equal
to 0xFF. Solved by casting NAND_CMD_NONE to u8 which will avoid int
promotion.
Signed-off-by: Patrick van Gelder <patrick.vangelder@nl.bosch.com>
Reviewed-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable mux based clocks to populate LPD_LSBUS clock to xilinx_wwdt
driver. Skip reading clock rate for the mux based clocks with
parent clock id is zero.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
Currently, the entry "bus-width = <8>" in the ZynqMP's sdhci nodes
is not evaluated. This results in the bus width staying at its default
value (4 bit in HS200 mode).
Fix this by calling mmc_of_parse. This function also checks for the
"no-1-8-v" and "max-frequency" entries. Remove the handling of those
nodes from this driver.
Signed-off-by: Benedikt Grassl <Benedikt.Grassl@rohde-schwarz.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for additional timer clock which belongs to tunnel
domain.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The rk_edp.c and rk_lvds.c files reference rk_setreg which is declared in
hardware.h so include it so the drivers build. Adjust rk_lvds.c so
includes are in alphabetical order while updating.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
The build currently fails with
drivers/spi/mpc8xxx_spi.c:64:3: warning: implicit declaration of function ‘dev_err’ [-Wimplicit-function-declaration]
...
drivers/spi/built-in.o: In function `mpc8xxx_spi_set_speed':
drivers/spi/mpc8xxx_spi.c:227: undefined reference to `dev_err'
Fixes: 4856cc7a97 (mpc8xxx_spi: implement real ->set_speed)
Fixes: 1a7b462dee (mpc8xxx_spi: put max_cs to use)
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
This patch converts S900 clock driver to something common that can
be used for other SoCs, for instance S700(few of clk registers are same).
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Synchronize device tree bindings with v5.5-rc6 tag with commit id
"b3a987b0264d".
Also, it removes older clock binding defined for S900 along with undocumented
compatible string "actions,s900-serial" from serial driver and adapts clock
driver to cater to new bindings.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This patch adds "actions,owl-uart" string to the owl uart driver. It
is also defined in Linux kernel.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
This function does not modify the device to change it to use const *, so
that callers with a const udevice * can call it without a cast.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Commit 6293b0361d ("mtd: nand: pxa3xx: add raw read support") added the
local data_len variable in handle_data_pio() to track read size, but
forgot to update the condition of drain_fifo() call. That happens to
work when the layout last_chunk_size != 0. But when last_chunk_size ==
0, drain_fifo() is not called to read the last chunk, which leads to
"Wait timeout!!!" error. Fix this.
Fixes: 6293b0361d ("mtd: nand: pxa3xx: add raw read support")
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
After a successful upgrade, multiple problem during boot sequence may
trigger the altbootcmd process.
This patch adds a version and an upgrade_available entries to the
bootcount file to enable/disable the bootcount check.
When failing to read the bootcount file it will consider that bootcount is
enabled, acting as previously, and update the file accordingly.
The bootcount file is only saved when `upgrade_available` is true, this
allows to save writes to the filesystem.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
mt7531 is a 7-ports switch with 5 embedded giga phys, and uses the same
MAC design of mt7530. The cpu port6 supports SGMII only. The cpu port5
supports RGMII or SGMII in different model.
mt7531 is connected to mt7622 via both RGMII and SGMII interfaces.
In this patch, mt7531 cpu port5 or port6 is configured to maximum
capability to align CPU MAC setting.
The dts has been committed in the commit 6efa450565 ("arm: dts:
mediatek: add ethernet and sgmii dts node for mt7622")
Signed-off-by: Landen Chao <landen.chao@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
The mpc8xx watchdog can work either in 'reset mode' or 'NMI mode'.
The selection can be done at startup only.
It is desirable to select the mode without rebuilding U-boot.
It is also desirable to disable the watchdog without rebuilding.
At watchdog startup, check environment variable 'watchdog_mode'.
If it is 'off', the watchdog is not started. If it is 'nmi',
the watchdog is started in NMI mode. Otherwise, it is started
in reset mode which is the default mode.
Signed-off-by: Charles Frey <charles.frey@c-s.fr>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
commit 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
converted pinctrl driver to livetree. In this conversion, the call to
read pinctrl-single,pins/bits property is provided with pinctrl device
pointer instead of pinctrl config pointer. Because of this none of the
pins gets configured. Fix it by passing the right udevice pointer.
Fixes: 719cab6d2e ("dm: pinctrl: convert pinctrl-single to livetree")
Reported-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- iproc_sdhci memory leak fix and enable R1B resp quirk
- more mmc cmds and several mmc updates from Heinirich
- Use bounce buffer for tmio sdhci
- Alignment check for tmio sdhci
RPMB support is used by the 'mmc rpmb' command and by the OP-TEE support.
We do not need it in SPL.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Implement get_b_max() for the Renesas R-Car SDHI controller driver, limit
the b_max per hardware capabilities such that select Gen2 controllers have
16bit block transfer limit, the rest has 32bit block transfer limit and on
Gen3, the block transfer limit on addresses above the 32bit boundary is set
to 1/4 of the malloc area.
Originally, on Gen3, the block transfers above the 32bit area were limited
to PIO only, which resulted in (R8A7795 Salvator-X , HS200 eMMC):
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.151 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 11.090 seconds
with bounce buffer in place and b_max adjustment in place:
=> time mmc read 0x0000000700000000 0 0x10000
time: 0.156 seconds
=> time mmc read 0x0000000700000000 0 0x100000
time: 2.349 seconds
Note that the bounce buffer does mallocate and free the bounce buffer
for every transfer. Experiment which removes this results in further
increase of read speed, from 2.349s to 2.156s per 512 MiB of data,
which is not such a significant improvement anymore. It might however
be interesting to have bounce buffer directly in the MMC core or even
block core.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Add getter function which permits adjusting the maximum number of
blocks that could be read in a single sustained read transfer based
on the location of the source/target buffer and length, before such
transfer starts.
This is mainly useful on systems which have various DMA restrictions
for different memory locations, e.g. DMA limited to 32bit addresses,
and where a bounce buffer is used to work around such restrictions.
Since the U-Boot bounce buffer is mallocated, it's size is limited
by the malloc area size, and the read transfer to such a buffer must
also be limited. However, as not all areas are limited equally, the
b_max should be adjusted accordinly as needed to avoid degrading
performance unnecessarily.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The R-Car SDHI DMA controller has various restrictions. To work around
those restrictions without falling back to PIO, implement bounce buffer
with custom alignment check function which tests for those limitations.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
set_ios_post return type changed from void to int, correcting
the same to fix compilation warning.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Provide command 'mmc wp' to power on write protect boot areas on eMMC
devices.
The B_PWR_WP_EN bit in the extended CSD register BOOT_WP is set. The boot
area are write protected until the next power cycle occurs.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Register value table for DDR PHY clock divider are wrong. They should be
0 or 1 for divide-by-2 or divide-by-4, respectively. Not 1 or 2. Current
values do not make sense, since 2 cannot be achieved, because the
register is only 1 bit long (mask is set to 1).
This fixes clk dump reporting DDR PHY clock rate differently from Linux.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
In R-Car Gen 3, there is a DMA controller restriction of SDHI.
When the transfer exceeding the 4 kByte boundary is performed while
the DRAM address is not 128 byte aligned, the bus is occupied.
This patch avoids this.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
- Further cleanups for 'make refcheckdocs'
- Another BTRFS fix.
- Support for automatic decompression of images with booti as well as
unlz4 command for manual decompression.
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
-----BEGIN PGP SIGNATURE-----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=1Ffl
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20200420' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- enable DM_RNG on meson boards
- fix SMBIOS info on Odroid-C2
- Fix video output on GXBB/GXL/GXM boards
- add USB gadget support for GXL/GXM boards
Add set_mode function in the Amlogic GXL PHYs that will be called by
the arch code to switch PHYs from/to gadget mode.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add generic_phy_get_by_node() to get a PHY phandle from a node instead
of a udevice.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
[narmstrong: fixed by including ofnode.h in generic-phy.h]
This adds the PCA9546 4-channel i2c bus switch.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
In some cases U-Boot runs the same binary on different board versions.
In wandboard, for example, there are versions with the PFUZE100 PMIC
populated and others without it.
When the PMIC is not present, it is not really useful to get PMIC error,
so change the error message level to debug instead.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Heiko Schocher <hs@denx.de>
ENABLE signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
DOTCLK signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
VSYNC signal can now be flipped by writing its bitmask on vdctrl0
register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
HSYNC signal can now be flipped according to display_flags bitmaks by
writing its bitmask on vdctrl0 register.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
struct display_timings provides more informations such clock and DE
polarity, so let's refactor the code to use struct display_timings
instead of struct ctfb_res_modes, so we'll become able to get clock and
DE polarity settings and set register according to them in the next patch.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add support for i.MXRT by adding CONFIG_IMXRT in register structure and
adding .compatible = "fsl,imxrt-lcdif".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Allow using DM CLK instead of mxs_set_lcdclk() so we can avoid to
implement a special function to set lcd clock on i.MXRT.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Since video_ctfb_mode_to_display_timing() has been implemented by moving
sunxi_ctfb_mode_to_display_timing() to video_modes.c and it's meant to be
used by other video subsystem, let's use it instead of local
sunxi_ctfb_mode_to_display_timing().
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function converts from "struct ctf_res_modes" to
"struct display_timing".
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Need to add set_parent() callback to allow dts assigned-clock-parents to
work so let's add it accordingly.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
mxsfb needs PLL5 as source, so let's setup it at its default frequency
specified in RM(650Mhz).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
"video:" must be "video", ":" is a typo.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
pllv3 PLLs have powerdown/up bits but enable bits too. Specifically
"enable bit" enable the pll output, so when dis/enabling pll by
setting/clearing power_bit we must also set/clear enable_bit.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Fix some errors pointed out by 'make refcheckdocs'.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Display TEE version at information level; this patch replaces
debug() call to dev_info() in print_os_revision() function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jens Wiklander <jens.wiklander@linaro.org>
Currently ATA commands are defined both in include/libata.h and
include/ata.h. Use the command definitions from include/libata.h where
applicable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
If CONFIG_CMD_NAND is disabled, get_nand_dev_by_index() is not
accessible.
This fix allows the build to succeed in this case.
Signed-off-by: Francois Gervais <fgervais@distech-controls.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Add a simple pincontrol associated to the sandbox gpio driver,
that allows to check pin configuration with the command pinmux.
The pinmux test is also updated to test behavior with 2 pincontrols.
Example to check LED pin configuration:
=> pinmux list
| Device | Driver | Parent
| pinctrl-gpio | sandbox_pinctrl_gpio | root_driver
| pinctrl | sandbox_pinctrl | root_driver
=> pinmux dev pinctrl-gpio
=> pinmux status
a0 : gpio input .
a1 : gpio input .
a2 : gpio input .
a3 : gpio input .
a4 : gpio input .
a5 : gpio output .
a6 : gpio output .
...
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add tests for new API set_dir_flags and set_dir_flags and associated
code in gpio uclass.
Test support for new flags GPIO_OPEN_DRAIN, GPIO_OPEN_SOURCE
GPIO_PULL_UP and GPIO_PULL_DOWN.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Cleanup binding support, use the generic binding by default
(test u-class gpio_xlate_offs_flags function) and add
specific binding for added value.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add test for "pins" configuration in gpio uclass with set_state() ops
and test for generic parsing of pinconf_param array).
set_state() is called by:
- pinctrl_generic_set_state
|- pinctrl_generic_set_state_subnode
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add param information in pin information output.
This update prepare unitary test for pin configuration
in pinctrl node.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the ops for GPIO driver set_dir_flags() to set the dir flags.
The user can update the direction and configuration
of each GPIO with a only call to dm_gpio_set_dir_flags() or
dm_gpio_set_dir() and respecting the configuration provided by
device tree (saved in desc->flags).
When these optional ops are absent, the gpio uclass use the mandatory
ops (direction_output, direction_input, get_value) and desc->flags
to manage only the main dir flags:
- GPIOD_IS_IN
- GPIOD_IS_OUT
- GPIOD_IS_OUT_ACTIVE
- GPIOD_ACTIVE_LOW
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the ops for GPIO driver get_dir_flags(), allows to get dynamically
the current gpio configuration; it is used by the API function
dm_gpio_get_dir_flags().
When these optional ops are absent, the gpio uclass continues to use
the mandatory ops (direction_output, direction_input, get_value) and
value of desc->flags to manage only the main dir flags:
- GPIOD_IS_IN
- GPIOD_IS_OUT
- GPIOD_IS_OUT_ACTIVE
- GPIOD_ACTIVE_LOW
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit manages the new dir flags that can be used in gpio
specifiers to indicate the pull-up or pull-down resistor
configuration for output gpio (GPIO_PULL_UP, GPIO_PULL_DOWN)
or the Open Drain/Open Source configuration for input gpio
(GPIO_OPEN_DRAIN, GPIO_OPEN_SOURCE).
These flags are already supported in Linux kernel in gpio lib.
This patch only parse and save the direction flags in GPIO
descriptor (desc->flags), it prepares the introduction of new ops
to manage them.
The GPIO uclass supports new GPIO flags from device-tree
(GPIO_XXX define in include/dt-bindings/gpio/gpio.h)
and translate them in the dir flags (GPIOD_XXX):
- GPIO_PULL_UP => GPIOD_PULL_UP
- GPIO_PULL_DOWN => GPIOD_PULL_DOWN
- GPIO_OPEN_DRAIN => GPIOD_OPEN_DRAIN
- GPIO_OPEN_SOURCE => GPIOD_OPEN_SOURCE
This patch also adds protection in the check_dir_flags function for
new invalid configuration of the dir flags.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the flag management in GPIO uclass: the desc->flags is always
combined with the requested flags and the GPIO descriptor is updated
for further call.
Add a function dm_gpio_get_dir_flags to get dynamically
the current dir_flags (configuration and value).
This patch prepare introduction of the dir flags support with new ops.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a macro to provide the GPIO output value according
the dir flags content.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a dir flags validity check with a new function
check_dir_flags.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the function _dm_gpio_set_dir_flags to set dir flags
without check if the GPIO is reserved.
Separate the reserved check for "set_dir" and "set_dir_flags".
This patch is a preliminary step to add new ops.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce the function _gpio_get_value to get the GPIO value
without check if it is reserved.
This patch prepare new ops introduction.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a helper function gpio_desc_init() to initialize the gpio descriptor;
with this function the flags will be always set to 0.
It wasn't the case before this patch in dm_gpio_lookup_name.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch removes the ops get_open_drain/set_open_drain
and the API dm_gpio_get_open_drain/dm_gpio_set_open_drain.
The ops only provided in one driver (mpc8xxx gpio) and the
associated API is never called in boards.
This patch prepare a more generic set/get_dir_flags ops,
including the open drain property.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Migrate pinctrl-generic to livetree:
- dev_for_each_property
- dev_read_prop_by_prop
- dev_read_string_count
- dev_read_string_index
and get rid of DECLARE_GLOBAL_DATA_PTR.
This patch solves the parsing issue during sandbox tests for pin
configuration (OF_LIVE is activated in sandbox_defconfig
and sub node are not correctly parsed in
pinctrl_generic_set_state_subnode with fdt lib API).
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add functions to iterate on all property with livetree
- dev_read_first_prop
- dev_read_next_prop
- dev_read_prop_by_prop
and
- ofnode_get_first_property
- ofnode_get_next_property
- ofnode_get_property_by_prop
And helper: dev_for_each_property
For example:
struct ofprop property;
dev_for_each_property(property, config) {
value = dev_read_prop_by_prop(&property, &propname, &len);
or:
for (res = ofnode_get_first_property(node, &property);
!res;
res = ofnode_get_next_property(&property))
{
value = ofnode_get_property_by_prop(&property, &propname, &len);
....
}
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Convert 'pinctrl-single' using livetree functions
- dev_read_prop
- dev_read_u32_default
- dev_read_u32_array
- dev_read_bool
- dev_read_addr
and get rid of DECLARE_GLOBAL_DATA_PTR.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This is pretty minor set of changes mostly touching HSDK board:
* Enable on-chip reset controller on HSDK
* Add possibility to turn-on & off L2$ on more
recent ARC HS processors.
* AXI tunnel clock calculation on HSDK
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl6YjlcACgkQxIHbvCwF
GsQ6Jg/+KVRQF0Dn2jiag8Me9ZhafZx4xGTI3LEzFD7V9kG3dmUzbO3m8a5dEevW
bcPNA6EmcKAjyP09AZY4C8ns4sU7wzPu/GQvApD4S5+vcuNbEqRHfW6zzReNXq09
t89DrFH+XLhGnh4uSh0hmfjrlIPVi86hs/f57vKRayrBu8W2yGPci3SNTO5Y0AY1
to7sxP3hGlDCUhqIABWp5ylpWWUSG1MsVNcMOnHpj+jl0iWWYP46EQrGr95egQor
gcGgUOLdOLLOHPYUIOBmo9INnS2MbvE9Mfgh5Bw7JW8DIu/Xp7r1qePQyMLsngc1
pO5yzwMq6EQy6OjuYnXdIBXtHOlZ8rnE9pbTgyUR8T/2CdL2hqr9ddpqa4ryDABX
iaQF8FG+KhY0XQ5EIJV7pEkvf9TMwGguJNlOkmJPeub2n9i0k1tPk0Rwq5ZWWBIn
rHcgZXwl0On3O3f0HvfL0Oas5u9KE1HhA12h/EVmu2Muy36x2WxAAzDnsH19HzqU
QnWBAo8VMyp3qTIZjb3y+qrxcU/joPGt9+hxmur03hzmKOJ9JNOv6vExb+yUIyXQ
4ML6jvTvSVZbvkP++0zMKOjT8ks3xv5q84oFD5Gp4cG8ZpHpA9dj3mXM92Waepo4
pAkko5IGQ4SqaGIBltEQzrG+cCiHHezdD/raCwAo6DgYSmfZUvc=
=+ZDZ
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-07-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-07-rc1
This pull request
* provides an implementation of UEFI secure booting
* fixes a problem with the rsa_mod_exp driver which stops some boards
from booting when CONFIG_RSA is enabled which is needed for UEFI
secure booting
* enables the EFI_RNG_PROTOCOL if DM_RNG is enabled
* fixes some function comments
We set wrong tunnel PLL frequency when we request 125MHz tunnel clock.
Fix that.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl6YdaMRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYLRwf8C+vKmERVLLcrMZMMiLctbY2kVflJV8zG
RjFwBcazZDPYjtHqClFZtJyIDYzgkVQRo+QPcdLxjcA+gjSXdteeRa0XTsBTXOZQ
kbs7yBkL+rCIO2WyXtuyajsmDMQtqM5vYgeBdTeYnJu7NVxwRMYrUqqAKLolNpIN
SKNYz+a8OEOG2EetbTdwwrmSpNy/cZ3wDGYK25DFTte8/vCZMRBTPiiNSrLp/RsM
xIojRcLqzARwpvPfFZ8psASKei9+5oIICUrNvwwQGtjepvZwdFQEl90SKaHw8kMf
sP9rxuqlEN5ec6xnMTUgwfnyBZgNIMSeb4KVPP1rxN2eAa5+bK1OlQ==
=gyyY
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-10apr20-take2' of git://git.denx.de/u-boot-dm
Functions for reading indexed values from device tree
Enhancements to 'dm' command
Log test enhancements and syslog driver
DM change to read parent ofdata before children
Minor fixes
At present a device can read its ofdata before its parent has done the
same. This can cause problems in the case where the parent has a 'ranges'
property, thus affecting the operation of dev_read_addr(), for example.
We already probe parent devices before children so it does not seem to be
a large step to do the same with ofdata.
Make the change and update the documentation in this area.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Ley Foon Tan <ley.foon.tan@intel.com>
The content dm_ofnode_pre_reloc() is identical with ofnode_pre_reloc()
defined in drivers/core/ofnode.c and used only three times:
- drivers/core/lists.c:lists_bind_fdt()
- drivers/clk/at91/pmc.c::at91_clk_sub_device_bind
- drivers/clk/altera/clk-arria10.c::socfpga_a10_clk_bind
So this function dm_ofnode_pre_reloc can be removed and replaced
by these function calls by ofnode_pre_reloc().
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Now reading a 32 bit value from a device-tree property can be expressed
as reading the first element of an array with a single value.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
The patch adds helper functions to allow reading a single indexed u32
value from a device-tree property containing multiple u32 values, that
is an array of integers.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
When removing a device the power domains it uses are generally powered
off. But when we are trying to unbind all devices (e.g. for running tests)
we don't want to probe a device in the 'remove' path.
Add a new flag to skip this power-down step.
Signed-off-by: Simon Glass <sjg@chromium.org>
This failure path is tricky to debug since it continues after failure and
there are a lot of error paths. Add logging to help.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the new function dm_scan_fdt_ofnode_path() to scan all the nodes
which aren't devices themselves but may contain some:
- "/chosen"
- "/clocks"
- "/firmware"
The patch removes the strcmp call in recursive function dm_scan_fdt_live()
and also corrects a conflict with the 2 applied patches in
the commit 1712ca2192 ("dm: core: Scan /firmware node by default")
and in the commit 747558d014 ("dm: fdt: scan for devices under
/firmware too"): the subnodes of "/firmware" (optee for example)
are bound 2 times.
For example the dm tree command result on STM32MP1 is:
STM32MP> dm tree
Class Index Probed Driver Name
-----------------------------------------------------------
root 0 [ + ] root_driver root_driver
firmware 0 [ ] psci |-- psci
sysreset 0 [ ] psci-sysreset | `-- psci-sysreset
simple_bus 0 [ + ] generic_simple_bus |-- soc
...
tee 0 [ + ] optee |-- optee
...
tee 1 [ ] optee `-- optee
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Variable count is initialized at the start of every round of the while
loop and it is not used after the while loop. So there is no need to
initialize it beforehand.
Identified by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The value of parent is not changed in the first if statement. So we can
merge the two if statements depending on parent.
Indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some compilers produce a warning about 'child' being used before init.
Silence this by setting to NULL at the start.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Currently, the baud rate is never set on boot. This works ok when a previous
bootloader has configured the baudrate properly, or when the baudrate is set to
a reasonable default in the serial driver's probe(). However, when this is not
the case, we could be using a different baud rate than what was configured.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
This header relates to ACPI and we are about to add some more ACPI
headers. Move this one into a new directory so they are together.
The header inclusion in pci_rom.c is not specific to x86 anymore, so drop
the #ifdef CONFIG_X86.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
ACPI (Advanced Configuration and Power Interface) is a standard for
specifying information about a platform. It is a little like device
tree but the bindings are part of the specification and it supports an
interpreted bytecode language.
Driver model does not use ACPI for U-Boot's configuration, but it is
convenient to have it support generation of ACPI tables for passing to
Linux, etc.
As a starting point, add an optional set of ACPI operations to each
device. Initially only a single operation is available, to obtain the
ACPI name for the device. More operations are added later.
Enable ACPI for sandbox to ensure build coverage and so that we can add
tests.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
At present if reading a BAR returns 0xffffffff then the value is masked
and a different value is returned. This makes it harder to detect the
problem when debugging.
Update the function to avoid masking in this case.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Add a means to avoid configuring a device when needed. Add an explanation
of why this is useful to the binding file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the cleanup() method is called on every transfer. It should
only be called on failing transfers. Fix this and tidy up the error
handling a little.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This device should use ready-gpios rather than ready-gpio. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the cr50 driver claims the locality and does not release it for
Linux. This causes problems. Fix this by tracking what is claimed, and
adding a 'remove' method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Different CPUs may support different address widths, meaning the amount of
memory they can address. Add a property for this to the cpu_info struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some callers may need the UART base clock speed value.
Provide it in the ->getinfo() callback.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some callers of serial_getinfo() would like to know the UART base
clock speed in order to make decision what to pass to OS in some
cases. In particular, ACPI SPCR table expects only certain base
clock speed and thus we have to act accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Function rsa_verify_key() is not called before relocation. So there is no
need to load the UCLASS_MOD_EXP drivers before relocation.
This avoid a failure to boot for pine64-lts_defconfig with CONFIG_RSA=y.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- Enable bootd, iminfo, imxtract on ST defconfig
- Rename LEDs to match silkscreen on AV96
- Add KS8851-16MLL ethernet on FMC2
- Define FMC2 base address
- net: dwc_eth_qos: implement reset-gpios for stm32
- net: dwc_eth_qos: implement phy reg and max-speed for stm32
-----BEGIN PGP SIGNATURE-----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=FNeD
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200415' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Replace STM32MP1_TRUSTED by TFABOOT flag
- Enable bootd, iminfo, imxtract on ST defconfig
- Rename LEDs to match silkscreen on AV96
- Add KS8851-16MLL ethernet on FMC2
- Define FMC2 base address
- net: dwc_eth_qos: implement reset-gpios for stm32
- net: dwc_eth_qos: implement phy reg and max-speed for stm32
Activate ARCH_SUPPORT_TFABOOT and replace the arch stm32mp
specific config CONFIG_STM32MP1_TRUSTED by the generic CONFIG_TFABOOT
introduced by the commit 535d76a121 ("armv8: layerscape: Add TFABOOT
support").
This config CONFIG_TFABOOT is activated for the trusted boot chain,
when U-Boot is loaded by TF-A.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add management of property "reg" to configure @ of phy and
also "max-speed" property to specify maximum speed in Mbit/s
supported by the device
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add management of property "reset-gpios" in the node identified by
"phy-handle" to configure any GPIO used to reset the PHY.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Patrice CHOTARD <patrice.chotard@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Get the watchdog platform clock from the DTS file
using clk subsystem and use the same for calculating
ticks in msec.
Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com>
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Some watchdog devices, e.g. external gpio-triggered ones, must be
reset more often than once per second, which means that the current
rate-limiting logic in watchdog_reset() fails to keep the board alive.
gpio-wdt.txt in the linux source tree defines a "hw_margin_ms"
property used to specifiy the maximum time allowed between resetting
the device. Allow any watchdog device to specify such a property, and
then use a reset period of one quarter of that. We keep the current
default of resetting once every 1000ms.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
This function is a bit large for an inline function, and for U-Boot
proper, it is called via a function pointer anyway (in board_r.c), so
cannot be inlined.
It will shortly set a global variable to be used by the
watchdog_reset() function in wdt-uclass.c, so this also allows making
that variable local to wdt-uclass.c.
The WATCHDOG_TIMEOUT_SECS define is not used elsewhere.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Stefan Roese <sr@denx.de>
- Misc enhancements to Clearfog, including board variant detection
(Joel)
- Misc enhancements to Turris Mox, including generalization of the
ARMADA37xx DDR size detection (Marek)
The value of local variable ecc is immediately overwritten. So we can
remove the first assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
For some layouts it is necessary to adjust the CK_DELAY parameter to
successfully complete DDR training. Add the ability to specify the
CK_DELAY in the mv_ddr_topology_map.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
