In attempts to speed up SPL and reduce size, the MDIO pin muxing
was inadvertently affected. Since the ethernet driver will setup
the pin muxing when ethernet is loaded, this patch will also
pinmux the MDIO pins at the same time. Once an DM compatible
MDIO driver is available, this can be removed.
Fixes: 877ab2423b ("ARM: davinci: da850: Manual pinmux only
when PINCTRL not available")
Signed-off-by: Adam Ford <aford173@gmail.com>
The commit 355be915ed ("arm: dts: k3-am654: Update power-domains
property for each node") has updated the power-domain cells value
and updated power-domains property in various existing dts nodes but
missed updating the cpsw_nuss node. This results in the following
build warning, fix this.
arch/arm/dts/k3-am654-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
arch/arm/dts/k3-am654-r5-base-board.dtb: Warning (power_domains_property): /interconnect@100000/interconnect@28380000/cpsw_nuss@046000000:power-domains: property size (8) too small for cell size 2
Fixes: 355be915ed ("arm: dts: k3-am654: Update power-domains property for each node")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCXUBgGwAKCRDKSWXLKUoM
IcJJAKCUoHRpqNgcZUiE10D9/VhZ3bUVtwCgi0fzSlqgHVG2EzApfqN+2KfrGJo=
=7i0K
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx/FPGA changes for v2019.10
fpga:
- Xilinx virtex2 cleanup
- Altera cyclon2 cleanup
zynq:
- Minor Kconfig cleanup
- Add psu_init configuration for Z-turn board
zynqmp:
- Add support for pmufw config passing to PMU
- script for psu_init conversion
- zcu1275 renaming
xilinx:
- Add support for UltraZed-EV SoM
Avnet UltraZed-EV Starter Kit is composed by the UltraZed-EV SoM and the
only publicly-available compatible carrier card. The SoM is based on the EV
version of the Xilinx ZynqMP SoC+FPGA.
The psu_init_gpl.c file has been generated from the board definition files
at [0] using Vivado 2018.3 and then minimized by
tools/zynqmp_psu_init_minimize.sh. Manually removed serdes init code since
it is not mentioned in device tree and fixed a checkpatch error.
[0] 3686c9ff7d/ultrazed_7ev_cc/1.1
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Name of this platform has changed and released to customers that's why
name has also changed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Series-to: uboot
Enable the driver-model on da850-evm. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Enable the driver-model on da850-lcdk. We need to add a dummy nand node
to the device tree, as the real nand node is a sub-node of the aemif
device.
On linux the aemif driver populates all its child nodes, but we can't do
it in u-boot currently.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
- Clean up and migrate to use common rockchip spl board file
- Clean up and migrate to use common rockchip board file
- Increase rk3288 CONFIG_SYS_BOOTM_LEN to 16MB
"u-boot,spl-boot-order" is more flexible and other rockchip SoCs
has convert to use it, migrate to use the new dts property.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We are using "u-boot,spl-boot-order" now and re-use the
definition from rk3288-u-boot.dtsi, so remove it directly here.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Provide proper display timings for lcdif node, used by mxsfb DM_VIDEO
enabled framebuffer driver.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Fix lcdif DT node and make it conform to the structure defined in the
Linux devicetree bindings [1]. Currently there is support only for
old style lcdif node definitions.
[1] https://www.kernel.org/doc/Documentation/devicetree/bindings/display/mxsfb.txt
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Add dumb node for NXP Display Control Unit0(DCU), which permits DM_ENABLED
converted driver to be probed. Currently no display timings are provided
in this node.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Like the other Logic PD OMAP35/DM37 boards, this board has device
tree enabled for U-Boot. This patch converts the board to enable
SPL_OF_CONTROL and further shrinks the device tree in SPL to limit
it to UART3 (console), MMC1, i2c1, and GPIO4 (for mmc1 CD and WP).
There appears to be a bug in minicom so users may need to
switch the minicom terminal emulation to ANSI from VT102 due
to the junk that gets pushed out of the UART on startup.
Signed-off-by: Adam Ford <aford173@gmail.com>
Update the MMC2_HS200_MANUAL1 iodelay values to match with the latest
dra76x data manual[1].
Also this particular pinctrl-array is using spaces instead of tabs for
spacing between the values and the comments. Fix this as well.
[1] http://www.ti.com/lit/ds/symlink/dra76p.pdf
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
If UHS speed modes are enabled, a compatible SD card switches down to 1.8V
during enumeration. If after this a software reboot/crash takes place and
on-chip ROM tries to enumerate the SD card, the difference in
IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card.
The fix for this is to have support for power cycling the card in
hardware (with a PORz/soft-reset line causing a power cycle of the card).
Because the beaglebone X15 (rev A,B and C), am57xx-evms and am57xx-idks don't
have this capability, disable voltage switching for these boards.
The major effect of this is that the maximum supported speed mode is now
high speed(50 MHz) down from SDR104(200 MHz).
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Sync with kernel dts by adding pinmuxes for mmc1 and mmc2. This fixes an
issue where mmc2 (eMMC) was coming up in HS52 mode instead of the
highest DDR52 mode.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
During a short period when the bus voltage is switched from 3.3v to 1.8v,
(to enumerate UHS mode), the mmc module is disabled and the mmc IO lines
are kept in a state according to the programmed pad mux pull type.
According to 4.2.4.2 Timing to Switch Signal Voltage in "SD Specifications
Part 1 Physical Layer Specification Version 5.00 February 22, 2016", the
host should hold CLK low for at least 5ms.
In order to keep the card line low during voltage switch, the pad mux of
mmc1_clk line should be configured to pull down.
Add a new pinctrl group for clock line without pullup to be used in boards
where mmc1_clk line is not connected to an external pullup.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Common Processor board is the baseboard that has most of the actual connectors,
power supply etc. A SOM (System on Module) is plugged on to the common
processor board and this contains the SoC, PMIC, DDR and basic highspeed
components necessary for functionality. Add initial dt support for this
common processor board.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the power-domain-cells to 2 and add the permissions
to each node. Mark the following nodes accessed by r5 as shared:
- DDR node
- main uart 0
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
For STM32 QSPI driver, "st,stm32-qspi" compatible string was first
introduced in U-boot. But later in kernel side, "st,stm32f469-qspi"
was used.
To simplify, align U-boot QSPI compatible string with kernel one.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
For STM32 QSPI driver, "st,stm32-qspi" compatible string was first
introduced in U-boot. But later in kernel side, "st,stm32f469-qspi"
was used.
To simplify, align U-boot QSPI compatible string with kernel one.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
We share the same default SPL boot order for all rk3288 boards,
use dts instead of hard code in board file.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-firefly board have different setting for sdmmc
io, sync then from kernel mainline:
6fbc7275c7a9 Linux 5.2-rc7
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use LPDDR4-100 sdram timings dtsi for RockPI-4 board.
All these timings are processed during TPL stage of rock-pi-4 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.
Bootchain after and before this change:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Use DDR3-1866 2GB ddr timings dtsi for 1GB NanoPi Neo4 board.
Since sdram rk3399 support dynamic stride and rank detection it
can able to detect 1GB ddr eventough the timings are meant for
dual channel, 2GB size.
Bootchain after and before this change are:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
This certainly fix the second channel data training initialization
since we have dynamic rank, stride where second channel capabilities
are clear or memset to 0.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Use LPDDR4-100 sdram timings dtsi for Rockpro64 board.
All these timings are processed during TPL stage of rockpro64 board,
bootchain. This make TPL would replace rockchip in house rkbin in
current bootchain.
Bootchain after and before this change:
TPL -> SPL -> U-Boot proper
rkbin -> SPL -> U-Boot proper
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram timings for LPDDR4-100 via rk3399-sdram-lpddr4-100.dtsi file.
all timings are dumped from rkbin/bin/rk33/rk3399_ddr_800MHz_v1.20.bin
Associated LPDDR4 board -u-boot.dtsi can include this to make these
timings available during SPL or TPL stages.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
