Gumstix Overo COMs with board revision 0x4 use a different Wifi and
Bluetooth module: Wi2Wi's W2CBW0015. No other code changes are required
in u-boot---just handling of this particular board revision.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Since B&R boards uses only MMC-Controller #1, it only
wastes time if we initialize #0 first to see that there is nothing.
Cc: <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T104xrdb has several sleep management signals that are used for deep
sleep. They are enabled by OS to enter deep sleep and should be
disabled by u-boot when cores wake up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
According to AN3638, CRC of NXID v1 is at the end of the
256-byte I2C memory. The wrong CRC32 offset prevents Uboot
from reading system information from EEPROM. No NXID v0 is
being used on Freescale boards.
Signed-off-by: Ebony Zhu <b45385@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Because sandbox is not a real hardware, setting vendor=sandbox is
almost meaningless.
This commit sets sandbox's vendor field to '-'.
It is a good thing that it decreases one level directory hierarchy.
The files board/sandbox/sandbox/* have been moved to board/sandbox/*.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This reverts commit 258060905e.
Conflicts:
boards.cfg
Wrong patch 25806090 was applied by accident. Revert it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
Exynos4 can be used the dwmmc controller for eMMC.
Then it needs to check dwmmc_init() at first.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Proper adjustment for supporting DFU at GONI target has been made.
The s5p_goni.h file has been updated. Moreover the code for low level
USB initialization has been added to GONI board code.
The malloc pool has been enlarged in order to support larger buffer
sizes needed by DFU implementation.
Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Exception handling is basically identical for all ARM targets.
Factorize it out of the various start.S files and into a
single vectors.S file, and adjust linker scripts accordingly.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
ps7_init.c and ps7_init.h are supposed to be exported by hw project
and copied to board/xilinx/zynq/ directory.
We want them to be ignored by git.
So what we should do is to always treat them as external files
rather than replacing ps7_init.c
This commit does:
- Move a weak function ps7_init() to arch/arm/cpu/armv7/zynq/spl.c
and delete board/xilinx/zynq/ps7_init.c
- Compile board/xilinx/zynq/ps7_init.c only when it exists
- Add .gitignore to ignore ps7_init.c/h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
ps7_init.c exported by hw project has #include "xil_io.h" line
but U-Boot does not have "xil_io.h".
So we get an error on SPL build:
ps7_init.c:12581:20: fatal error: xil_io.h: No such file or directory
We can delete the include directive in ps7_init.c to avoid this error.
But it is painful to do this every time we export ps7_init.c file.
Instead, we can put an empty xil_io.h in the same directory
so we can directly copy ps7_init.c as is.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Tom Rini <trini@ti.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When CONFIG_FPGA is defined but CONFIG_SPL_FPGA is not, the build fails:
board.c: In function 'board_init':
board.c:41:3: error: 'fpga' undeclared (first use in this function)
fpga = fpga010;
Fix this by expanding the "#if.." around this block to match the other
FPGA checks and don't compile this block when buildign for SPL without
FPGA support.
Tested a bootloader that had CONFIG_FPGA defined without CONFIG_SPL_FPGA,
this now compiles without errors and loading FPGA from u-boot works.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
board/xilinx/zynq/board.c:17:13: warning: symbol 'fpga' was not declared. Should it be static?
board/xilinx/zynq/board.c:20:13: warning: symbol 'fpga010' was not declared. Should it be static?
board/xilinx/zynq/board.c:21:13: warning: symbol 'fpga015' was not declared. Should it be static?
board/xilinx/zynq/board.c:22:13: warning: symbol 'fpga020' was not declared. Should it be static?
board/xilinx/zynq/board.c:23:13: warning: symbol 'fpga030' was not declared. Should it be static?
board/xilinx/zynq/board.c:24:13: warning: symbol 'fpga045' was not declared. Should it be static?
board/xilinx/zynq/board.c:25:13: warning: symbol 'fpga100' was not declared. Should it be static?
board/xilinx/zynq/board.c:120:5: warning: symbol 'board_mmc_init' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].
[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Move 'cdev' in board.c down to under #ifdef's where it's used]
Signed-off-by: Tom Rini <trini@ti.com>
The actual board name is draco and dxr2 is the target name.
In the future we'll have different targets based on draco board.
All changes are purely non-functional and basically rename dxr2
to draco.
One style fix in board.c that existed already before.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
* remove setting LED in user button function.
We want to decouple reading user button and setting LED. This
two things need to be done independently.
* led cmd can be used to control LEDs that are defined in board file
having a led cmd, one can easily set LEDs in u-boot shell. For
example bootcmd can be extended to disable status LED before
loading kernel.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
* add parameters for factory and print them at start up to
facilitate control of right DDR3 settings in EEPROM.
* cosmetic changes in a couple of printfs
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
For dxr2 board DXR2_IOCTRL_VAL is set by data in EEPROM. In pxm2
board it does not make sense to have dxr2 as prefix. Replace it with
more meaningful DDR prefix.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The Venice2 pinmux spreadsheet was updated to fix a few issues. Import
those changes into the U-Boot pinmux initialization tables.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This re-imports the entire Venice2 pinmux data from the board's master
spreadsheet, and makes use of the new IO clamping GPIO initialization
table features. This makes the board port fully compliant with the
required HW-defined pinmux initialization sequence.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The HW-defined procedure for booting Tegra requires that
CLAMP_INPUTS_WHEN_TRISTATED be enabled before programming the pinmux.
Modify the Jetson TK1 board to do this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The HW-defined procedure for booting Tegra requires that some pins be
set up as GPIOs immediately at boot in order to avoid glitches on those
pins, when the pinmux is programmed. This patch implements this
procedure for Jetson TK1. For pins which are to be used as GPIOs, the
pinmux mux function need not be programmed, so the pinmux table is also
adjusted.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The return value has not been checked by its caller, until recent change
of using generic board architecture. The error of this function is not
critical enough to hang the system. Printing the warning message is enough
to catch user's attention. U-boot should continue to boot to give user
a chance to fix the EEPROM. Chaning the return value to 0 to avoid hanging
in the board_init_r().
Signed-off-by: York Sun <yorksun@freescale.com>
We only need u-boot to bother about a single core in the QEMU machine.
Everything that would require additional knowledge of more cores gets
handled by QEMU and passed straight into the payload we execute.
Because of this setup, it would be counterproductive to enable SMP support
in u-boot. We would have to rip CPUs out of already existing spin tables
and respin them from u-boot. It would be a pretty big mess.
So only assume we have a single core. This fixes errors about CONFIG_MP
being disabled.
Signed-off-by: Alexander Graf <agraf@suse.de>
This should prevent the problems that the CCF can deadlock with certain
traffic patterns.
This also fixes the workaround for A-006559 that was not correctly
implemented before.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Fix the IRQ/GPIO settings: all the muxed GPIO/external IRQs that are
used as internal interrupts are defined as GPIOs to avoid confusion
between the internal/external interrupts.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This adds the reset support for the following devices that was until
then not implemented:
- BFTIC4
- QSFPs
This also fixes the configuration of the prst behaviour for the other
resets: Only the u-boot and kernel relevant subsystems are taken out of
reset (pcie, ZL30158, and front eth phy).
Most of the prst config move to misc_init_f(), except for the PCIe
related ones that are in pci_init_board and the bftic and ZL30158 ones
that should be done as soon as possible.
Only the behavior of the Hooper reset is changed according to the
documentation as the application is not able to not configure the switch
when it is not reset.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Add readout of dip-switch to revert to factory settings.
If one or more dip-switch are set, launch bank 0 that contains the
bootloader to do the required action.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The unit LEDs are managed by the QRIO CPLD. This patch adds support for
accessing these LEDs in the QRIO.
The LEDs then are set to a correct boot state:
- UNIT-LED is red
- BOOT-LED is on.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Adds Support for PowerOne ZM7300 voltage regulator.
This device is available on some Freescale Boards like B4860QDS
and has to be programmed to adjust the voltage on the board.
The device is accessible via I2C interface.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Connect FPGA version with appropriate operations
to remove huge switch-cases for every FPGA family.
Tested on Zynq. Spartan2/Spartan3/Virtex2 just compile test.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch includes following changes :
* Adds gpio pin numbering support for EXYNOS SOCs.
To have consistent 0..n-1 GPIO numbering the banks are divided
into different parts where ever they have holes in them.
* Rename GPIO definitions from GPIO_... to S5P_GPIO_...
These changes were done to enable cmd_gpio for EXYNOS and
cmd_gpio has GPIO_INPUT same as s5p_gpio driver and hence
getting a error during compilation.
* Adds support for name to gpio conversion in s5p_gpio to enable
gpio command EXYNOS SoCs. Function has been added to asm/gpio.h
to decode the input gpio name to gpio number.
Example: SMDK5420 # gpio set gpa00
Signed-off-by: Leela Krishna Amudala <l.krishna@samsung.com>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit 345b77ba removed some nand_spl boards but
it missed to delete linker scripts.
These linker scripts are not used now.
And one more fix:
amcc/acadia does not support nand_spl anymore, so remove
#if !defined(CONFIG_NAND_U_BOOT) ... #endif
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Stefan Roese <sr@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
CONFIG_BOARDDIR is not referenced in these linker scripts.
The comment /* CONFIG_BOARDDIR */ is misleading.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.
In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Some functions in include/net.h are ported from
include/linux/etherdevice.h of Linux Kernel.
For ex.
is_zero_ether_addr()
is_multicast_ether_addr()
is_broadcast_ether_addr()
is_valid_ether_addr();
So, we should use the same function name as that of Linux Kernel,
eth_rand_addr(), for consistency.
Besides, eth_rand_addr() has been implemented as an inline function.
So it should not be surrounded by #ifdef CONFIG_RANDOM_MACADDR.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
Prior to commit 33a02da0, all boards must have board/${BOARD}/
or board/${VENDOR}/${BOARD}/ directory.
Now this rule is obsolete.
It looks weird that sandbox defines "vendor" and "board" just for
meeting the old U-Boot directory structure.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Now that sandbox has a good base of features, the README is quite out of
date. Update it, and document the new features.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
There's nothing Samsung-/board-specfic about the implementation of
ums_init(). Move the code into cmd_usb_mass_storage.c, so that it can
be shared by any user of that command.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Now that ums_disk_init() is so simple, there's no need for it to be a
separate function. Instead, just add it to the tail end of ums_init().
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
There's no reason to believe that an MMC device will incorrectly report
its capacity. Remove error checking of this value from ums_disk_init()
to simplify it.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
These values aren't set anywhere at present, and hence have no effect.
The concept of a single global offset/number of sectors to expose through
USB Mass Storage doesn't even make sense in the face of multiple storage
devices. Remove these defines to simplify the code.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The USB Mass Storage function could equally well support a SATA device
as support an MMC device. Update struct ums to contain a block device
descriptor, not an MMC device descriptor.
Cc: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This change removes LCD menu download mode info screen.
Now key press timeout is checked in function download_menu()
and menu options are displayed directly after PWR + VOLUP keys.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Increase menu loop delay to 200 ms helps choose the right
menu option by user. Before this, each time key was pressed
the current menu option was changed few times.
Now it changes only once and also changes few times if key
is pressed for a longer time.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This change allows reset device environment to default without using u-boot
console, which is useful for system developers.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This menu option allows restore gpt.
This is usefull and no needs access to the u-boot console.
For proper operation:
- each partition uuid should be set in environment or
- CONFIG_RANDOM_UUID should be defined for automatically uuid setting
After operation success device is going to be reset.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Function cmd_process() runs commands with directly given list of arguments
but it doesn't expand given environmental variables names as macros.
Command "gpt" as one of arguments expects expanded macro e.g. $partitions
so it needs to be called by function run_command().
Changes:
- extend array mode_name by lower case commands names - used by find_cmd()
- put each command arguments into one string - used by run_command()
- use run_command() instead of cmd_process()
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
In cases when MMC hadn't been initialized before, ie. by the user or other
subsystem, it was still uninitialized while UMS media capacity check,
leading to broken ums command.
UMS has to initialize resources it uses.
Tested on Samsung Goni.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.
I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.
Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.
Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.
CONFIG_USB_CABLE_CHECK was removed.
Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
ECSPI chipselect (MX6_PAD_EIM_D19__GPIO3_IO19) is used with GPIO functionality,
so it does not make sense to set its pad as SPI pin.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Eric Nelson <eric.nelson@boundarydevices.com>
Acked-by: Eric Nelson <eric.nelson@boundarydevices.com>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
MACH_TYPE_LAGER and CONFIG_MACH_TYPE are not already available on Lager board.
This removes them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum CPU clock of R8A7790 that are used in lager board is 1.4GHz.
This change to use the maximum clock in this board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Maximum CPU clock of R8A7791 that are used in koelsch board is 1.5GHz.
This change to use the maximum clock in this board.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This update QoS version 0.240 for ES1 and version 0.310 for ES2.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There is koelsch where ES2 revision of R8A7791 was put on.
This is different in Qos setting.
This adds Qos setting for ES2 revision of R8A7791.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This changes from r8a7790_ to rcar_.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This changes from r8a7791_ to rcar_.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch adds support for the new PMC440 hardware revision 1.4.
The board now uses Micrel KSZ9031 phys.
Add missing i2c initialization before reading bootstrap eeprom.
Fix a couple of coding style issues.
Make local functions static.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
create vendor board directory ids and move ids8247 board to it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
There should be a break for case PHY_INTERFACE_MODE_SGMII, otherwise it
will fall into case PHY_INTERFACE_MODE_RGMII.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.
This support of CPLD includes
- files and register defintion
- Commands to swtich alternate bank and default bank
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.
Signed-off-by: York Sun <yorksun@freescale.com>
The MDC generate by default value of MDIO_CLK_DIV is too high i.e. higher
than 2.5 MHZ. It violates the IEEE specs.
So Slow MDC clock to comply IEEE specs
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/lubbock/*
- Remove include/configs/lubbock.h
- Cleanup defined(CONFIG_LUBBOCK)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rsdproto/*
- Remove include/configs/rsdproto.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rpxsuper/*
- Remove include/configs/RPXsuper.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/RPXlite/*
- Remove board/RPXClassic/*
- Remove include/configs/RPXlite.h
- Remove include/configs/RPXClassic.h
- Clean-up defined(CONFIG_RPXCLASSIC)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
- Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
- Remove the entries from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/genietv/*
- Remove include/configs/GENIETV.h
- Clean-up if defined(CONFIG_GENIETV)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
In the case of SPL or NOR_BOOT (no SPL involved) we need to include
certain code in the build. Use !CONFIG_SKIP_LOWLEVEL_INIT rather than
CONFIG_SPL_BUILD || CONFIG_NOR_BOOT to make the code clearer, and to
make supporting XIP QSPI boot clearer in the code.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Wolfgang Denk <wd@denx.de>
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <nm@ti.com>
Ethernet driver configures the CPSW, SGMI and Phy and uses
the the Navigator APIs. The driver supports 4 Ethernet ports and
can work with only one port at a time.
Port configurations are defined in board.c.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
We previously only supported QSPI_1 (single) support. Add QSPI_4 (quad)
read support as well. This means we can be given one of two boot device
values, but don't care which it is, so perform a fixup on the QSPI_4
value. We add a qspiboot build target to better show how you would use
QSPI as a boot device in deployment. When we boot from QSPI, we can
check the environment for 'boot_os' to control Falcon Mode.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This change makes the behaviour slightly more rebust and will match
other implementations which can use getenv_yesno directly.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
We use the same variable as a3m071 in the environment to determine if we
should boot into Linux or U-Boot. This is useful on boards like
Beaglebone Black or AM335x GP EVM where we have persistent storage for
the environment.
Signed-off-by: Tom Rini <trini@ti.com>
Similar to OMAP5uEVM, PandaBoard, BeagleBoard-XM has a USB based
ethernet without MAC address embedded. So fake a MAC address following
the similar strategy used on OMAP5 and PandaBoard family.
Signed-off-by: Nishanth Menon <nm@ti.com>
TI platforms such as OMAP5uevm, PandaBoard, use equivalent
logic to generate fake USB MAC address from device unique DIE ID.
Consolidate this to a generic location such that other TI platforms such
as BeagleBoard-XM can also use the same.
NOTE: at this point in time, I dont yet see a need for a generic dummy
ethernet MAC address creation function, but if there is a need in the
future, this can be further abstracted out.
Signed-off-by: Nishanth Menon <nm@ti.com>
Replace the custom sr32() bit manipulation function in
arch/arm/cpu/armv7/omap3/board.c and board/ti/panda/panda.c
by standard I/O accessors.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>