gpio.h - Added missing copyright in few files.
rsa-mod-exp.h - Corrected copyright in the file.
fsl_sec.h - Added missing license in files
drivers/crypto/fsl/Makefile - Removed the incomplete GPLv2 license and replaced it with GPLv2+ license
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
The menuconfig for drivers are getting more and more cluttered
and unreadable because too many entries are displayed in a single
flat menu. Use hierarchic menu for each category.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Update to apply again in a few places, drop USB hunk]
Signed-off-by: Tom Rini <trini@konsulko.com>
This adds dcache support for dwc2. The DMA buffers must be DMA aligned and
is flushed for outgoing transactions before starting transfer. For
ingoing transactions it is invalidated after the transfer has finished.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
[trini: Update to apply again on top of DM patches]
Signed-off-by: Tom Rini <trini@konsulko.com>
The mailbox buffer is required to be at least 16 bytes aligned, but for
cache invalidation and/or flush it needs to be cacheline aligned.
Use ALLOC_CACHE_ALIGN_BUFFER for all mailbox buffer allocations.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
This allows scanning the twl4030 keypad, storing the result in a 64-byte long
matrix with the twl4030_keypad_scan function.
Detecting a key at a given column and row is made easier with the
twl4030_keypad_key function.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Reviewed-by: Tom Rini <trini@konsulko.com>
This adds support for detecting a few inputs exported by the TWL4030.
Currently-supported inputs are the power button, USB and charger presence.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This adds support for powering off (the omap3 SoC) from the twl4030. This is
especially useful when the kernel does not actually power off the device using
this method but reboots and leaves it up to the bootloader to actually turn the
power off.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The change adds support of LPC32xx SLC NAND controller.
LPC32xx SoC has two different mutually exclusive NAND controllers to
communicate with single and multiple layer chips.
This simple driver allows to specify NAND chip timings and defines
custom read_buf()/write_buf() operations, because access to 8-bit data
register must be 32-bit aligned.
Support of hardware ECC calculation is not implemented (data
correction is always done by software), since it requires a working
DMA engine.
The driver can be included to an SPL image.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
Some NAND controllers define custom functions to read data out,
respect this in order to correctly support bad block handling in
simple SPL NAND framework.
NAND controller specific read_buf() is used even to read 1 byte in
case of connected 8-bit NAND device, it turns out that read_byte()
may become outdated.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tom Warren <twarren@nvidia.com>
Acked-by: Scott Wood <scottwood@freescale.com>
remove unneeded udelay() in this function, as we use
the dev_ready pin.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
The current 4.5 timeout for the autonegotiation are not enough to
complete it on my platform. Using the Intel E1000 PCIe card in the
Marvell db-mv784mp-gp eval board. So lets increase the timeout to
8 seconds.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
The return type of pmic_read and pmic_write is signed int, so
correct variable 'ret' from type unsigned int to int.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
1. Add new regulator driver pfuze100.
* Introduce struct pfuze100_regulator_desc for maintaining info
for one regulator.
2. Add new Kconfig entry DM_REGULATOR_PFUZE100 for pfuze100.
3. This driver intends to support PF100, PF200 and PF3000.
4. Add related macro definition in pfuze header file.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
1. Support driver model for pfuze100.
2. Introduce a new Kconfig entry DM_PMIC_PFUZE100 for pfuze100
3. This driver intends to support PF100, PF200 and PF3000, so add
the device id into the udevice_id array.
4. Rename PMIC_NUM_OF_REGS macro to PFUZE100_NUM_OF_REGS.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
If there is no property named 'regulator-name' for regulators,
choose node name instead, but not directly return failure value.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
The dw_mmc driver uses printf() in various places.
These bloat the code and cause problems for SPL. Use debug() where possible
and try to return a useful error code instead.
panto: Small rework to make it apply against top of tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Add Ethernet PHY for BCM Cygnus SoC
Signed-off-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Steve Rae <srae@broadcom.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
With commit e3a77218a2 the MII bus is only
reset if a reset handler is registered. If there is no reset handler there
is no need to wait for a device to come out of the reset.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The rxbd is not correctly handled in case of a frame physical error
(FPE) or frame size error (FSE). The rxbd must be cleared and
advanced in case of an error to avoid receive stall.
Signed-off-by: Daniel Inderbitzin <daniel.inderbitzin@gmail.com>
LPC32xx MAC and clock control configuration requires some minor quirks
to deal with a phy connected by RMII.
It's worth to mention that the kernel and legacy BSP from NXP sets
SUPP_RESET_RMII == (1 << 11) bit, however the description of this bit is
missing in shared LPC32x0 User Manual UM10326 Rev. 3, July 22, 2011
and in LPC32x0 Draft User Mannual Rev. 00.27, November 20, 2008, also
in my tests an SMSC LAN8700 phy device connected over RMII seems to
work correctly without touching this bit.
Add support of RMII, if CONFIG_RMII is defined, this option is aligned
with a number of boards, which already define the same config value.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Tested-by: Sylvain Lemieux <slemieux@tycoint.com>
This change rearranges general MAC configuration and PHY specific
configuration of MAC registers (duplex mode and speed), before this
change set bits related to PHY configuration in MAC2 and COMMAND
registers are rewritten by the following writing to the registers.
Without the change auto negotiation on boot quite often is not
completed in reasonable time:
Waiting for PHY auto negotiation to complete......... TIMEOUT !
Additionally MAC1_SOFT_RESET clear bit is removed since it is done in
preceding lpc32xx_eth_initialize() and in lpc32xx_eth_halt(), instead
added missing MCFG_RESET_MII_MGMT on device initialization.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
The lpc32xx_eth_phylib_init() function is capable to connect LPC32XX
MAC to some specified phy by phy id, by chance the single user of
lpc32xx_eth has CONFIG_PHY_ADDR set to 0, however other boards may
have non-zero CONFIG_PHY_ADDR value, fix it.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to LPC32x0 User Manual the following bits in Command
register 0x3106_0100 are defined:
Bit Symbol
2 - Unused
3 RegReset
4 TxReset
5 RxReset
Fix wrong (1-bit shifted right) COMMAND_RESETS value, which sets
an unused bit, but neglects RxReset.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Acked-by: Albert ARIBAUD (3ADEV) <albert.aribaud@3adev.fr>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tearing down an unitialized rx channel causes a pending address hole
event to be queued. When booting linux it will report this pending
as something like "Address Hole seen by USB_OTG at address 57fff584",
since u-boot did not handled this interrupt. Prevent that by not
tearing down the rx channel, when not receiving.
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Support the 88E1510 PHY which is very similar to the 88E1518.
I also set the INTn output and configured the LEDs.
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- The EEE fixup magic should also be enabled for RGMII
- Improved comments
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Hao Zhang <hzhang@ti.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch refer to linux kernel commit: d8b763e1e79f
net/macb: add TX multiqueue support for gem
by: Cyrille Pitchen
1. macb driver will check the register to find how many queues support for
this chip.
2. Then as we only use queue0 for tx, so we will set up all other queues
use a dummy descriptor, which USED bit is set. So those queues are not used.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
remove unnecessary clearing of SWSM.SWSM_SMBI when obtaining the SW
semaphore. This was introduced in 951860634f
while adding i210 support and should be now resolved by releasing the
semaphore when no longer needed.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This reverts commit 17da712024.
The i210/i211 do have the SW_FW_SYNC (0x5b5c) register and this is what should
be used when acquiring the semaphore.
I believe the issue that this patch was trying to resolve is now resolved
by properly releasing the semaphore once no longer needed.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Once the hwsw semaphore is acquired, it must be released when access to the
hw is completed. Without this subsequent calls to acquire will timeout
obtaining the semaphore.
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Aneesh Bansal <aneesh.bansal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
In case the data transfer failure happens, instead of returning
immediatelly, make sure the DMA is disabled, status register is
cleared and the bounce buffer is stopped.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Endless timeouts are bad, since if we get stuck in one, we have no
way out. Zap this one by implementing proper timeout.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
The driver didn't stop the bounce buffer in case a data transfer
failed. This would lead to memory leakage if the communication
between the CPU and the card is unreliable. Add the missing call
to stop the bounce buffer.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Tom Rini <trini@konsulko.com>
Currently the serial code assumes that there is always at least one serial
port (and panics / crashes due to null pointer dereferences when there is
none).
This makes it impossible to use u-boot on boards where there is no (debug)
serial port, because e.g. all uart pins are muxed to another function.
This commit adds a CONFIG_REQUIRE_SERIAL_CONSOLE Kconfig option, which
defaults to y (preserving existing behavior), which can be set to n on
such boards to make them work.
This commit only implements this for CONFIG_DM_SERIAL=y configs, as allowing
running without a serial port for CONFIG_DM_SERIAL=n configs is non trivial,
and is not necessary at this moment.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add composite video out support.
This only gets enabled on the Mele M3 for now, since that is were it
was tested. It will be enabled on more boards after testing.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for interlaced modes, this is a preparation patch for adding
composite out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a few extra sunxi display registers and constant defines.
Also rename some existing defines (e.g. dropping _GCTRL) and make
some more generic (e.g. dropping the 2x scaling from
SUNXI_LCDC_TCON1_TIMING_V_TOTAL).
This is a preparation patch for adding composite video out support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
We should only subtract 2 from the vblank time when using tcon1.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All the #ifdef-ery in selecting the default and fallback monitor type is
becoming unyielding and makes the code hard to read, replace it with a few
helper functions.
This will also be useful with the upcoming CHIP board which has display
adapter daughterboards which should be runtime detectable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
USB devices are not really designed to get the power bounced off and on
at them. Esp. USB powered harddisks do not like this.
Currently we power off the USB ports both on a "usb reset" and when
booting the kernel, causing the usb-power to bounce off and then back
on again.
This patch removes the powering off calls, fixing the undesirable power
bouncing.
Note this requires some special handling for the OTG port:
1) We must skip the external vbus check if we've already enabled our own
vbus to avoid false positives
2) If on an usb reset we no longer detect that the id-pin is grounded, turn
off vbus as that means an external vbus may be present now
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When SPL_NAND_SUNXI option is selected in config, set some configuration
options for sunxi NAND.
This commit also introduces the configurable options in Kconfig.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This driver adds NAND support to SPL.
It was tested on Allwinner A20.
Signed-off-by: Peter Gielda <pgielda@antmicro.com>
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
Signed-off-by: Karol Gugala <kgugala@antmicro.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Fix most of the dangling checkpatch issues, no functional change.
There are still 7 warnings, 1 checks , but those are left in place
for the sake of readability of the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_misc_config
instead of the various macros. This is just an sed exercise here, no
manual coding needed.
This patch actually removes the need to include any board-specific
files in sequencer.c , so sequencer.c namespace is now no longer
poluted by QTS-generated macros.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is another macro used to obfuscate the real code. The
T(INIT|RESET)_CNTR._VAL is always defined, so this indirection
is unnecessary. Get rid of this.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Just use READ_VALID_FIFO_SIZE directly, no need for this macro obfuscation.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_misc_config to wrap the remaining
misc configuration values in board file. Again, introduce a function,
socfpga_get_sdram_misc_config(), which returns this the structure. This
is almost the final step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_io_config
instead of the IO_* macros. This is just an sed excercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_io_config to wrap the IO configuration
values in board file. Introduce socfpga_get_sdram_io_config() function,
which returns this the structure. This is another step toward wrapping
the nasty QTS generated macros in board files and reducing the pollution
of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Actually convert the sequencer code to use socfpga_sdram_rw_mgr_config
instead of the RW_MGR_* macros. This is just an sed exercise here, no
manual coding needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce structure socfpga_sdram_rw_mgr_config to wrap the RW manager
configuration values in board file. Introduce a complementary function,
socfpga_get_sdram_rwmgr_config(), which returns this the structure.
This is another step toward wrapping the nasty QTS generated macros
in board files and reducing the pollution of the namespace.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Introduce two wrapper functions, socfpga_get_seq_ac_init() and
socfpga_get_seq_inst_init() to avoid direct inclusion of the
sequencer_auto_ac_init.h and sequencer_auto_inst_init.h QTS
generated files. This reduces namespace pollution again.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This is defined in the QTS-generated headers, so it must not be
re-defined in sequencer.h .
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
These parameters are not used in the code, zap them and the
macros which are used by them as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Move the files generated by QTS into the board directory, they should not
be part of the driver files at all.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Originally, both sdram_start and sdram_end were 64b values. The
sdram_start had no reason for being so, since our address space
is only 32b, so switching sdram_start to u32 is simple.
The sdram_end is a bit more complex, since it can actually be
set to (1 << 32) if someone really wanted to use an SoCFPGA with
4 GiB of DRAM and fixed the code around a little. But, the code
handling the protection rules internally decrements the sdram_end
variable anyway. Thus, instead of calling the code and passing in
the address of the SDRAM end, pass in the address already decremented
by one. This lets the sdram_end be 32b as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up so that it's obvious what it is doing,
fix the formating strings in debug outputs, add kerneldoc.
Make the function return proper errno-compliant return values
and propagate this change throughout sdram.c
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly clean up comments, add kerneldoc.
Also, zap assignment of the "cs" variable, which is outright
dead code, so just remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all of the CONFIG_HPS_SDR_CTRLCFG_* macros. This change
makes sdram.c completely clear of these macros and allows removing
of the ugly include of sdram.h . The namespace is now a much nicer
place!
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce socfpga_sdram_get_config() function implement in a board file,
which returns the socfpga_sdram_config structure. This is the last step
in cleaning up the socfpga_mmr_init_full(), but not the last step which
allows removing the inclusion of sdram.h from drivers/ddr/altera/sdram.c
thus far.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework remaining two register setting functions such that they only
return the final register value. Move the register setting into the
block of register I/O in sdram_mmr_init_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Merge sdr_set_*() functions which are just setting registers among
the sea of register setting in sdram_mmr_init_full(). There is no
need to keep them separate this way, there is nothing special about
them.
Signed-off-by: Marek Vasut <marex@denx.de>
Suck out all the CONFIG_HPS_SDR_CTRLCFG_* from sdram_mmr_init_full()
into the socfpga_sdram_config structure. There is still one ugly
macro left behind, but this will be taken care of in subsequent patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Zap all the ad-hoc readbacks from the registers and other useless
and broken debug output. This is really not useful and is only
confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
Introduce this seemingly massive structure, which holds required values
of all the registers of the SDRAM controller. The idea here is to avoid
including the sdram.h header file, which is full of ad-hoc macros that
polute the global namespace. Once the cleanup of sdram.c would be complete
and all registers would be loaded from this new socfpga_sdram_config, a
board file will only pass this structure into the sdram.c . This will
hide all the horrors generated by QTS in the board directory.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
Merge set_sdr_dram_timing{1,2,3,4,lowpwr}() into single function
set_sdr_dram_timing() , since there's no point in keeping all this
stuff separate anymore.
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of the constant clrsetbits_le32(), instead prepare the whole
content of the register once and write it at the end of the function.
The big plan here is to remove all the CONFIG_HPS_SDR_ macros, hide
them in QTS compatibility layer in board implementation and pass only
a small structure into the driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove all parameters of this function, since they are only constants
passed in from another function, so make them local. Also, rename the
function to get_errata_rows() as this is closer to what it does.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is implementing the DDR calibration Stage 3 as
described in Altera EMI_RM 2015.05.04 . The main body of this
function is almost identical to Stage 1.3 (DQ/DQS centering)
for all but two flags -- use_read_test and update_fom. Convert
this function to call rw_mgr_mem_calibrate_dq_dqs_centering()
with the correct flags set to trim down the code duplication.
Moreover, reorder the remnants in the function a little and
convert the function to return either 0 or -EIO in case of
success and failure respectively, to match the common return
value convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up coding style, mostly broken multiline formatting strings
in debug output. Also clean up data types and constify where applicable.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types and constify where applicable, fix broken multiline
debug strings and fix comments. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the return value of the function to match common convention
where 0 means success and negative means error. Fix the return
values in case of an error to use errno.h codes.
Signed-off-by: Marek Vasut <marex@denx.de>
The read_group and write_group arguments are the same in all
cases when this function is invoked, just merge them into one
rw_group argument. Also, clean up the function argument data
types and constify them.
Signed-off-by: Marek Vasut <marex@denx.de>
The search_stop_check() always resets the bit_chk to a new value,
so bit_chk will never survive between search_left_edge() and
search_right_edge() invocation. There is thus no need to pass
it into these functions, so make bit_chk local to them.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out center_dq_windows(), which is common code between
stage 2 and stage 3 of the calibration again and cater for
the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out the get_window_mid_index() for finding the best DQ
window centering. This is again code common to two stages, so
pull it out.
Signed-off-by: Marek Vasut <marex@denx.de>
First of all, don't break strings in the debug_cond() calls across
multiple lines. Next, zap a couple of really odd casts in the code.
Finally, make i into a signed variable, so it is possible to avoid
constructs of the form:
for (i = FOO;; i--) { <code>; if (i == 0) break; }.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from search_left_edge() and search_right_edge()
which checks whether searching for the window edge should stop. The
code is almost identical, so pull it into separate function and cater
for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
left edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out common code from rw_mgr_mem_calibrate_writes_center()
and rw_mgr_mem_calibrate_vfifo_center() for searching for the
right edge of the window. The code is almost identical, so pull
it into separate function and cater for the minor differences.
Signed-off-by: Marek Vasut <marex@denx.de>
Reorder the content of the function a little and fix the comments
so they at least become full sentences. Constify function args.
Fix the return value to match the common convention of 0 meaning
success.
Signed-off-by: Marek Vasut <marex@denx.de>
The C language has signed types, so make use of them. Fix this
obscene loop, which tries to do away with unsigned type, but
just makes the code more cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up the debug output handling at the end of the function
and factor out common function call from the condition.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement common sdr_find_phase_delay() function and convert all
places which use such code to this unified function. No functional
change to the code.
Signed-off-by: Marek Vasut <marex@denx.de>
If d != 0 after sdr_working_phase() finishes, the else branch
of the condition has no impact on anything at all, since work_end
was already set independently of the value of "d" . Zap this
useless code.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix data types, constify where applicable, fix comments and debug
strings. In case enough failing reads are detected, just return
right away instead of breaking from the loop. This lets us make
the error handling at the end much simpler.
Signed-off-by: Marek Vasut <marex@denx.de>
Pluck out all this VFIFO value counting, which turns out to be
completely unused. Thus, remove it to simplify the code.
Signed-off-by: Marek Vasut <marex@denx.de>
The "d" variable is set to 0 in sdr_backup_phase() and is not used
at all in sdr_nonworking_phase(). Make it local and zap it respectively.
Signed-off-by: Marek Vasut <marex@denx.de>
Wrap dtaps_per_ptap into the sdr_working_phase() function to trim
down the number of params. It's a constant too.
Signed-off-by: Marek Vasut <marex@denx.de>
It is now clear that the max_working_cnt variable is totally unused.
Zap the variable and zap other variables which became unused due to
this change too.
Signed-off-by: Marek Vasut <marex@denx.de>
Pull out the loop for eaching working/non-working DQS enable phase
into a separate function, as this is mostly common code between.
Clean up sdr_working_phase() and sdr_nonworking_phase() while switching
these two functions to the common sdr_find_phase().
Signed-off-by: Marek Vasut <marex@denx.de>
Get rid of found_{begin,end} variables. Instead of breaking out
through all of the loops, just return when the begin/end of the
window is found and be done with it. Also clean up the trailing
conditional expression, which is now much easier.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the arguments passed to these functions. The bit_chk is
overriden by rw_mgr_mem_calibrate_read_test_all_ranks() which
is invoked by all three sdr_*_phase() functions, so just make
this into local variable.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the arguments passed to these functions. The grp argument
does not have to be passed via reference, it's never modified
within either of those functions, so make it into a value.
Signed-off-by: Marek Vasut <marex@denx.de>
Reorder the end of the function a little by moving the conditional
debug output around a little. Rename the function from _centre() to
_center(). Document the function in kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is a treasure trove of ad-hoc iterative
implementations of mathematical functions. Replace all
of those with their non-iterative counterpart.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean up the arguments of this function. Most of the pointers
passed into the function are either not needed at all, or can
be passed as value instead of reference. Also fix the broken
multiline debug strings. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is only invoked from rw_mgr_mem_calibrate_dqs_enable_calibration()
and at this point, it is just one level of indirection, so wrap the
rw_mgr_mem_calibrate_vfifo_find_dqs_en_phase_sweep_dq_in_delay() into
rw_mgr_mem_calibrate_dqs_enable_calibration() to get rid of the level
of indirection.
Signed-off-by: Marek Vasut <marex@denx.de>
Replace at least one of the loops in this function with call of a
standard function call instead of the ad-hoc implementation. The
other one cannot be replaced, since the delay is incremented for
each group.
Signed-off-by: Marek Vasut <marex@denx.de>
The read_group and write_group params have the same value for all (one)
invocations of this function, just merge them into a single param.
Signed-off-by: Marek Vasut <marex@denx.de>
Start cleaning up this function. In the first part, just fix
the incorrectly broken debug strings and fix return value to
respect the common convention.
Signed-off-by: Marek Vasut <marex@denx.de>
Rework this function such that the code is more readable. Zap
unused parameter "num_tries" while at it. Also wrap parameter
"bit_chk" into this function as it's value is not used outside.
Finally, fix the return value from this function to match the
common expectation, where 0 means success.
Signed-off-by: Marek Vasut <marex@denx.de>
This function is called from one single place and it's sole purpose
is to call one single function with slightly modified arguments.
Zap this function to skip this useless intermediate step.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
Just extract this piece of functionality into separate function
to make the code better separated. This matches the division in
Altera documentation, Altera EMI_RM 2015.05.04 , section 1, the
UniPHY Calibration Stages.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
It is clear that the read_group and write_group variables
have the same value, to just make them into one variable
called rw_group. While doing this, constify the variables
as they are constant.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch fixes the broken formatting strings in debug_cond()
invocations.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch cleans up the handling of grp_calibrated such
that the variable isn't used all over the place, but just
very localy. This allows trimming down the indent issues.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch just tweaks the indentation so it is visible
what to do with the grp_calibrated variable.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
This patch just tweaks the indentation so it is visible
what is supposed to go where.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch just adds an expanded documentation header to the
aforementioned function. This is needed to make it easier to
match the purpose of this function with the documentation.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the the middle-loop of the mega-loop
this time and deal with the group_failed variable. Instead
of checking if the group failed in the previous calibration
part, just jump to the end of the loop if calibration did
fail and increment the counter. This shaves away one more
level of indent while making the code slightly more readable.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the last loop within the mega-loop
to make it actually readable and not an insane cryptic pile
of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the third loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the second loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
This is kind of microseries-within-series indent cleanup.
Rework the code for the first loop within the middle-loop
of the mega-loop to make it actually readable and not an
insane cryptic pile of indent failure.
It is likely that this patch has checkpatch warnings, but
for the sake of not breaking the code, these are ignored.
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Redo the mega-condition such that if the calibration is to be skipped,
the positive branch of the condition does all the work and returns.
The negative branch, which is in fact the default behavior, is then
converted to a code which is no longer conditional. This trims down
the indent by one level.
Signed-off-by: Marek Vasut <marex@denx.de>
Perform minor coding style cleanup of the mem_skip_calibrate() function,
clean up comments and add kerneldoc. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Turn the big inner if (RW_MGR_MEM_NUMBER_OF_RANKS == ...) conditional
into a switch {} statement instead. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
First, invert the logic of the if (odt_mode == ...) conditional to make
the OFF mode harder to miss. It is a short piece of code right at the
end, so move it up.
Also, clean up data types and constify where applicable and clean up
the cs_and_odt_mask assignment. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean mem_config() function. First, reorder the math done in the
function such that WLAT and RLAT computation is together. Then,
scrap contradictory comments which do not match the result of the
math at all. Next, extract the mem_precharge_and_activate() call
from the end of the function as it is completely unrelated here.
Finally, rename the function to mem_init_latency().
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up slightly by using clrsetbits_le32() to flip
bits in registers instead of cryptic bitmasks. Zap condition checking
for PHY_DEBUG_IN_DEBUG_MODE flag, which is never set. Split the
calibration report into separate debug_mem_calibrate() function.
Signed-off-by: Marek Vasut <marex@denx.de>
Init both structures with zeroes and zap all those zeroing shenanigans
further down in the sdram_calibration_full().
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the function up by getting rid of all the insane XOR-leftshift
combos when assembling register values. While at it, remove all the
ad-hoc variables necessary for this XOR-leftshift voodoo. Finally,
get rid of the iterative division implementation of two constants
and replace it with a DIV_ROUND_UP() macro :-)
Signed-off-by: Marek Vasut <marex@denx.de>
Contemporary CPUs can perform division just fine, use this
functionality and zap another implementation of iterative
division :-)
Signed-off-by: Marek Vasut <marex@denx.de>
Factor out almost common code from rw_mgr_mem_handoff() and
rw_mgr_mem_initialize() into separate rw_mgr_mem_load_user().
No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Clean the DQS and OCT parts of the function, clean up the chopped
formatting strings in debug_cond() and slightly improve the code.
Zap group_bgn argument as it is used only in debug messages. Document
the function using kerneldoc. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Apparently, in case of the DQ and DM, the value if the new_delay variable
is calculated, but the value is not used. Zap the entire code which does
calculate the value.
It is not clear to me whether or not the code is doing the right thing
in the first place. Right now, it calls scc_mgr_load_dq() and
scc_mgr_load_dm() respectively, but I suspect it might need to call
scc_mgr_apply_group_dq_out1_delay() and scc_mgr_apply_group_dm_out1_delay()
instead. This is something Altera must investigate.
Signed-off-by: Marek Vasut <marex@denx.de>
First, zap unused argument of the function. Next, clean up
the data types, constify where applicable, clean up comments
and add kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Move scc_mgr_set_hhp_extras() out of scc_set_bypass_mode() as it
has nothing to do in there. Instead, invoke it from mem_calibrate()
just before invoking scc_set_bypass_mode().
Signed-off-by: Marek Vasut <marex@denx.de>
Minor coding style cleanup for this function. Furthermore, move
ad-hoc debug_cond() calls from the only location from where this
function is invoked into this actual function.
Signed-off-by: Marek Vasut <marex@denx.de>
Make this function more readable, no functional change. Also, zap the
forward declaration, which is no longer needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement universal scc_mgr_set_all_ranks() function and convert
various ad-hoc implementations of similar functionality to use
this single function. Document the function in kerneldoc.
Signed-off-by: Marek Vasut <marex@denx.de>
Implement unified scc_mgr_set() function and convert all those
9 scc_mgr_set_*() ad-hoc functions to call this one function.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch just puts functions which look similar next to each
other, so they can be sorted out. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Turn the insides of these functions into trivial clrsetbits_le32()
and fix the data type of their argument to reflect it's actual size.
Signed-off-by: Marek Vasut <marex@denx.de>
Remove the remaining invocations of sdr_get_addr() and the function
itself. This makes the code a bit less cryptic.
Signed-off-by: Marek Vasut <marex@denx.de>
The debug messages missed proper newlines and/or spaces in them.
Fix the formatting.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@konsulko.com>
It is the configuration data that should go into the register,
not the register mask, just like the surrounding code does it.
Fix this typo.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Tom Rini <trini@konsulko.com>
Move the structure prototype from sdram.h header file into sdram.c
source file, since it is used only there and for local purpose only.
There is no point in having it global.
While at this move, fix the data types in the structure from uintNN_t
to uNN and fix the coding style a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
This patch enables the SDRAM controller that is used on Altera's SoCFPGA
family. This patch configures the SDRAM controller based on a configuration
file that is generated from the Quartus tool, sdram_config.h.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
The driver variable name is eth_sandbox, which is probably a copy-paste
mistake. Fix it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add the OF compatible property to match the SoCFPGA GMAC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In case the FPGA bitstream is aligned to 4 bytes, skip the
part of the assembler which handles unaligned bitstream.
Otherwise, that part will loop indefinitelly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Some devices are bound entirely by probing and do not have the benefit of
a device tree to give them a name. This is very common with PCI and USB. In
most cases this is fine, but we should add an official way to set a device
name. This should be called in the device's bind() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This new command can dump all device resources associated to
each device. The fields in every line shows:
- The address of the resource
- The size of the resource
- The name of the release function
- The stage in which the resource has been acquired (BIND/PROBE)
Currently, there is no driver using devres, but if such drivers are
implemented, the output of this command should look like this:
=> dm devres
- root_driver
- soc
- extbus
- serial@54006800
bfb541e8 (8 byte) devm_kmalloc_release BIND
bfb54440 (4 byte) devm_kmalloc_release PROBE
bfb54460 (4 byte) devm_kmalloc_release PROBE
- serial@54006900
bfb54270 (8 byte) devm_kmalloc_release BIND
- gpio@55000000
- i2c@58780000
bfb5bce8 (12 byte) devm_kmalloc_release PROBE
bfb5bd10 (4 byte) devm_kmalloc_release PROBE
- eeprom
bfb54418 (12 byte) devm_kmalloc_release BIND
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, Devres requires additional 16 byte for each allocation,
which is not so insignificant in some cases.
Add CONFIG_DEVRES to make this framework optional.
If the option is disabled, devres functions fall back to
non-managed variants. For example, devres_alloc() to kzalloc(),
devm_kmalloc() to kmalloc(), etc.
Because devres_head is also surrounded by an ifdef conditional,
there is no memory overhead when CONFIG_DEVRES is disabled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
devm_kmalloc() is identical to kmalloc() except that the memory
allocated with it is managed and will be automatically released
when the device is removed/unbound.
Likewise for the other variants.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
In U-Boot's driver model, memory is basically allocated and freed
in the core framework. So, low level drivers generally only have
to specify the size of needed memory with .priv_auto_alloc_size,
.platdata_auto_alloc_size, etc. Nevertheless, some drivers still
need to allocate/free memory on their own in case they cannot
statically know the necessary memory size. So, I believe it is
reasonable enough to port Devres into U-boot.
Devres, which originates in Linux, manages device resources for each
device and automatically releases them on driver detach. With devres,
device resources are guaranteed to be freed whether initialization
fails half-way or the device gets detached.
The basic idea is totally the same to that of Linux, but I tweaked
it a bit so that it fits in U-Boot's driver model.
In U-Boot, drivers are activated in two steps: binding and probing.
Binding puts a driver and a device together. It is just data
manipulation on the system memory, so nothing has happened on the
hardware device at this moment. When the device is really used, it
is probed. Probing initializes the real hardware device to make it
really ready for use.
So, the resources acquired during the probing process must be freed
when the device is removed. Likewise, what has been allocated in
binding should be released when the device is unbound. The struct
devres has a member "probe" to remember when the resource was
allocated.
CONFIG_DEBUG_DEVRES is also supported for easier debugging.
If enabled, debug messages are printed each time a resource is
allocated/freed.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently, we only have DM_FLAG_ACTIVATED to indicate the device
status, but we still cannot know in which stage is in progress,
binding or probing.
This commit introduces a new flag, DM_FLAG_BOUND, which is set when
the device is really bound, and cleared when it is unbound.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Simon Glass <sjg@chromium.org>
The 'ranges' property can be used to specify a translation from the system
address to the bus address. Add support for this using the dev_get_addr()
function, which devices should use to find their address.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present struct eth_device is passed around all over the place. This does
not exist with driver model. Add explicit arguments instead, so that with
driver model we can pass the correct things.
Signed-off-by: Simon Glass <sjg@chromium.org>
The AX_ prefix comes from the Asix driver. Since this is not that, we should
avoid this confusing prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Put all global data in a structure and move (what will be) common code into
common functions. This will make the driver-model conversion much easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all boards use garbage collection in their link step, so we should avoid
adding options that rely on this for prevention of code bloat. Add separate
Kconfig options for syscon and regmap uclasses.
Signed-off-by: Simon Glass <sjg@chromium.org>
fdt_addr_t is changed to phys_addr_t. The format in debug should be updated
to %pa to match the type.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Simon Glass <sjg@chromium.org>
Remove the old drivers (both the normal one and the cros_ec one) now that
we have new drivers that use driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since a gpio_desc is allowed to be invalid we should return an error
indicating that the operation cannot be completed. This can happen if the
GPIO is optional - e.g. some devices may have a reset line and some may
not.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not print a message from the driver when the display is set up.
This is normal behaviour. Change this message to use debug().
Also remove the double newline on another debug message.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since the timeout is reported through normal channels, and is sometimes
expected (e.g. if the bus is being probed for a non-existent device),
don't display the message in the driver.
In general, drivers should not write to the console as this limits their
usefulness in error conditions.
Signed-off-by: Simon Glass <sjg@chromium.org>
This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). There is no setup
required by this chip, other than to adjust power-down and reset pins, and
those are managed by the uclass.
Signed-off-by: Simon Glass <sjg@chromium.org>
This chip provides an eDP to LVDS bridge which is useful for SoCs that don't
support LVDS displays (or it would waste scarce pins). The setup is included
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
We haven't quite got pinctrl ready to apply to mainline. We don't want to
GPIO pull-up/down support to the driver model GPIO layer either. So work
around this for now.
We can address this when pinctrl is complete.
Signed-off-by: Simon Glass <sjg@chromium.org>
A video bridge typically converts video from one format to another, e.g.
DisplayPort to LVDS. Add driver model support for these with a simple
interface to control activation and backlight. The uclass supports GPIO
control of power and reset lines.
Signed-off-by: Simon Glass <sjg@chromium.org>
Not all regulators can be set up automatically. Adjust the code so that
regulators_enable_boot_on() will return success when some are skipped.
Only genuine errors are reported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Some regulators use the wrong voltage register and thus it is not possible
to control them. Fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This should write the register, not read it. Fix this bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The driver name should not have a space in it. Also the regulator names
should match the case of the device tree. Fix these problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports changing voltage and enabling/disabling each regulator. It
supports the standard device tree binding and supports driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
This PMIC is used with SoCs which need a combination of BUCKs and LDOs. The
driver supports probing and basic register access. It supports the standard
device tree binding and supports driver model. A regulator driver can be
provided also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The TPS65090 has 7 FETs which are modelled as regulators. This allows them
to be controlled by drivers easier, accessed through the 'regulator' command
and used by other drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
The existing TPS65090 driver does not support driver model. Add a new one
that does. This can be used as a base for a regulator driver also. It uses
the standard device tree binding.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
As a debugging aid, allow UART3 to be used as a debug UART in SPL. This
is a precursor to proper UART support, which requires a substantial
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a debug UART implementation for this serial driver. It does not set up
pinmux automatically - this must be done before calling debug_uart_init().
Signed-off-by: Simon Glass <sjg@chromium.org>
The debug UART code needs to perform the same init as the normal UART
driver. In preparation for this, move the init code into two functions, one
for the basic init and one for setting the baud rate. This will make adding
debug UART support easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a driver to support the special LDO access used by spring. This is a
custom method in the cros_ec protocol - it does not use an I2C
pass-through.
There are two implementation choices:
1. Write a special LDO driver which can talk across the EC. Duplicate all
the logic from TPS65090 for retrying when the LDO fails to come up.
2. Write a special I2C bus driver which pretends to be a TPS65090 and
transfers reads and writes using the LDO message.
Either is distasteful. The latter method is chosen since it results in less
code duplication and a fairly simple (30-line) implementation of the core
logic.
The crosec 'ldo' subcommand could be removed (since i2c md/mw will work
instead) but is retained as a convenience.
Signed-off-by: Simon Glass <sjg@chromium.org>
The Chrome OS EC supports tunnelling through to an I2C bus on the EC. This
currently uses a copy of the I2C command code and a special 'crosec'
sub-command.
With driver model we can define an I2C bus which tunnels through to the EC,
and use the normal 'i2c' command to access it. This simplifies the code and
removes some duplication.
Add an I2C driver which tunnels through to the EC. Adjust the EC code to
support binding child devices so that it can be set up. Adjust the existing
I2C xfer function to fit driver model better.
For now the old code remains to allow things to still work. It will be
removed in a later patch once the new flow is fully enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
The existing driver model implementation uses the old non-driver-model code
to operate, but has become impossibly tangled as a result. The actual
algorithm is quite simple.
Also the normal-speed and high-speed buses are quite different and it
doesn't seem that useful to put them in the same driver.
Finally, there is a bug which breaks communication with the Maxim sound
codec and may cause problems with other device.
Rewrite the driver model code for normal-speed operation so that it is
easier to understand, and fix the bug. Add a TODO to split the drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This function should not use mixed case, and it is simpler to use
clrbits_le32() when clearing bits. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
While I2C supports multi-master buses this is difficult to get right.
The implementation on the master side in software is quite complex.
Clock-stretching and the arbitrary time that an I2C transaction can take
make it difficult to share the bus fairly in the face of high traffic.
When one or more masters can be reset independently part-way through a
transaction it is hard to know the state of the bus.
This driver provides a scheme based on two 'claim' GPIOs, one driven by the
AP (Application Processor, meaning the main CPU) and one driven by the EC
(Embedded Controller, a small CPU aimed at handling system tasks). With
these they can communicate and reliably share the bus. This scheme has
minimal overhead and involves very little code. It is used on snow to
permit the EC and the AP to share access to the main system PMIC and
battery. The scheme can survive reboots by either side without difficulty.
This scheme has been tested in the field with millions of devices.
Since U-Boot runs on the AP, the terminology used is 'our' claim GPIO,
meaning the AP's, and 'their' claim GPIO, meaning the EC's. This terminology
is used by the device tree bindings in Linux also.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new I2C_MUX uclass. Devices in this class can multiplex between
several I2C buses, selecting them one at a time for use by the system.
The multiplexing mechanism is left to the driver to decide - it may be
controlled by GPIOs, for example.
The uclass supports only two methods: select() and deselect().
The current mux state is expected to be stored in the mux itself since
it is the only thing that knows how to make things work. The mux can
record the current state and then avoid switching unless it is necessary.
So select() can be skipped if the mux is already in the correct state.
Also deselect() can be made a nop if required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Sometimes it is useful to be able to transfer a raw I2C message. This
happens when the chip address needs to be set manually, or when the data to
be sent/received is in another buffer.
Add a function to provide access to this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Add a way to dump the contents of an I2C message for debugging purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
It is common for one node to reference another via a phandle. Add support
for obtaining an attached device by this method. As an example, a node may
have a 'power-supply' property which references a regulator, allowing the
driver to turn on its power.
Signed-off-by: Simon Glass <sjg@chromium.org>
Added 38.4MHz/48MHz entries to pll_x_table for CPU PLL. Needs
to be measured - should be close to 700MHz (1.4G/2).
Note that some freqs aren't in the PLLU table in T210 TRM
(13, 26MHz), so I used the 12MHz table entry for them. They
shouldn't be selected since they're not viable T210 OSC freqs.
Since there are now 2 new OSC defines, all tables (pll_x_table,
PLLU) had to increase by two entries, but since 38.4/48MHz are
not viable osc freqs on T20/30/114, etc, they're just set to 0.
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch fixes operation of our on-board AX88772B chip without EEPROM
but with a ethaddr coming from the regular U-Boot environment. This is
a forward port of some remaining parts initially implemented by
Antmicro.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
usb_stor_reset is only defined when USB storage support is enabled, thus the
function is not declared when such support is missing.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Currently, the second use of a gadget will fail, while the first one works.
Forcing the EP0 at every enable fix this issue.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that the musb-new driver has a Kconfig, we can move Kconfig options to
enable controllers to it, so that it's easier in e.g. menuconfig.
In addition, this allows declaring support for USB_MUSB_HOST/GADGET in
defconfigs instead of the USB_MUSB_SUNXI controller, that will get selected
automatically when needed.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
Having MUSB_HOST and MUSB_GADGET in Kconfig allows more flexibility with regard
to what Kconfig options to enable, such as USB_STORAGE or USB_KEYBOARD.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
USB-related options are usually prefixed with CONFIG_USB and platform-specific
adaptation for the MUSB controller already have a CONFIG_USB_MUSB prefix, so
this switches all MUSB-related options to a CONFIG_USB_MUSB prefix, for
consistency.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
There is no particular reason why the USB Kconfig option should be specific to
host mode. In prevision of adding MUSB host and gadget to Kconfig, this moves
the title and help message of the USB Kconfig option to a more generic format.
Adding comments to the usb Kconfig allows for a better separation and more
readability in generated configs and in menuconfig.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
The USB_ARCH_HAS_HCD currently serves no purpose and adds some confusion to the
required Kconfig options that are required to have USB support.
Dropping it makes things easier and doesn't break anything, since it was unused
anyways.
Signed-off-by: Paul Kocialkowski <contact@paulk.fr>
This patch makes the dwc2 controller like ehci / ohci / xhci controllers
by calling the board_usb_init() function from usb_lowlevel_init.
This can then be implemented by specific platforms to initialise
their USB hardware (phys / clocks etc).
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
We cannot use this driver when running from EFI as we have no direct hardware
access. In fact coreboot uses a different driver which uses tables provided
by coreboot. So far it does not seem possible to use a normal video driver
when booting from EFI.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a serial driver which makes use of EFI's console in/out service.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on Intel Crown Bay and QEMU
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present the PCI output displays 'Mem' when it allocates memory for a PCI
device, whether it is prefetchable or not. There is a distinction since the
memory comes from separate pools. Use 'Prf' instead of 'Mem' when allocating
prefetchable memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This option is not used by any board but appears to still be useful, at least
for testing. With recent commits it does not build, so fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file does not need its own way of doing debug(). Clean it up to use the
new way.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
In a final attempt to find a console UART this function uses the first
first available serial device. However the check for a valid device is
inverted.
This code is only executed when there is in fact no serial UART, but at
present it can fail to reach the panic_str() call in this case, and start
trying to use a non-existent UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This function needs to check the list has entries before traversing it.
Fix this bug.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We should not set up kernel screen_info when the vesa parameters are
insane, otherwise kernel will panic.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On some platforms pci devices behind bridge need to be probed (eg:
a pci uart on recent x86 chipset) before relocation. Remove such
limitation so that dm pci can be used before relocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default the bstopre value has been set to 0x100, used to be 1/4
value of refint. Modern DDR has increased the refresh time. Adjust
to 1/4 of refresh interval dynamically. Individual board can still
override this value in board ddr file, or to use auto-precharge.
Signed-off-by: York Sun <yorksun@freescale.com>
HW coherency won't work properly for CAAM write transactions
if AWCACHE is left to default (POR) value - 4'b0001.
It has to be programmed to 4'b0010.
For platforms that have HW coherency support:
-PPC-based: the update has no effect; CAAM coherency already works
due to the IOMMU (PAMU) driver setting the correct memory coherency
attributes
-ARM-based: the update fixes cache coherency issues,
since IOMMU (SMMU) driver is not programmed to behave similar to PAMU
Fixes: b9eebfade9 ("fsl_sec: Add hardware accelerated SHA256 and SHA1")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use fdt_setprop_u32() instead of fdt_setprop().
Fixes: 0181937fa3 ("crypto/fsl: Add fixup for crypto node")
Signed-off-by: Horia Geantă <horia.geanta@freescale.com>
Reviewed-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch will initialize PCIe controller on EP mode
1. Setup bar:
bar0 32bit 4K for specific configuration
bar1 32bit 8K for MSIX
bar2 64bit 4K for descriptor of memory
bar4 64bit 1M for DMA memory test
2. Setup iATU:
iATU inbound 0-3 to map bar transaction to memory address
started at CONFIG_SYS_PCI_EP_MEMORY_BASE
iATU outbound 0 to map 4G memory space
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
PCIe extends device's configuration space to 4k and provides
extended capability. The patch adds function to find them.
The code is ported from Linux PCIe driver.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC firware version 8.0.0 contains new command flags. This patch
contains modifications in FLIB files to support the new command flags.
Signed-off-by: Itai Katz <itai.katz@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The sampling of the oscillator can be done in multiple modes for
generating the entropy value. By default, this is set to von
Neumann. This patch changes the sampling to raw data, since it
has been discovered that the generated entropy has a better
'quality'.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The rtfrqmax & rtfrqmin set the bounds of the expected frequency of the
oscillator, when SEC runs at its maximum frequency. For certain platforms
(f.i. T2080), the oscillator is very fast and thus if the SEC runs at
a lower than normal frequency, the ring oscillator is incorrectly detected
as being out of bounds.
This patch effectively disables the maximum frequency check, by setting a
high enough maximum allowable frequency for the oscillator. The reasoning
behind this is that usually a broken oscillator will run too slow
(i.e. not run at all) rather than run too fast.
Signed-off-by: Alex Porosanu <alexandru.porosanu@freescale.com>
Acked-by: Ruchika Gupta<ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
strncpy is safer than strcpy, use it to instead of strcpy.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
when using printf, the parameter type need to be compatible
type, so transform them to compatible type
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add kconfig options for various SPI flashes and use them in cm-fx6 defconfig.
Cc: Jagan Teki <jteki@openedev.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
With recent additions to USB Kconfig the number of USB options had grown
large enough to warrant a separate menu for USB.
Add a Kconfig menu for USB.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Add Kconfig options for USB keyboard and use them for cm-fx6.
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add USB_EHCI_MX6 option to menuconfig and use it when migrating cm-fx6 usb
config to defconfig.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Derived from Tegra124, modified as appropriate during T210
board bringup. Cleaned up debug statements to conserve
string space, too. This also adds misc 64-bit changes
from Thierry Reding/Stephen Warren.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Commit aec241d "dm: pci: Use the correct hose when configuring devices"
was an attempt to fix pci bridge device configuration, but unfortunately
that does not work 100%. In pciauto_config_devices(), the fix tried to
call pciauto_config_device() with a ctlr_hose which is supposed to be
the root controller hose, however when walking through a pci topology
with 2 or more pci bridges this logic simply fails.
The call chain is: pciauto_config_devices()->pciauto_config_device()
->dm_pci_hose_probe_bus(). Here the call to dm_pci_hose_probe_bus()
does not make any sense as the given hose is not the bridge device's
hose, instead it is either the root controller's hose (case#1: if it
is the 2nd pci bridge), or the bridge's parent bridge's hose (case#2:
if it is the 3rd pci bridge). In both cases the logic is wrong.
For example, for failing case#1 if the bridge device to config has the
same devfn as one of the devices under the root controller, the call
to pci_bus_find_devfn() will return the udevice of that pci device
under the root controller as the bus, but this is wrong as the udevice
is not a bus which does not contain all the necessary bits associated
with the udevice which causes further failures.
To correctly support pci bridge device configuration, we should still
call pciauto_config_device() with the pci bridge's hose directly.
In order to access valid pci region information, we need to refer to
the root controller simply by a call to pci_bus_to_hose(0) and get the
region information there in the pciauto_prescan_setup_bridge(),
pciauto_postscan_setup_bridge() and pciauto_config_device().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
In dm_pci_hose_probe_bus(), pci_bus_find_devfn() is called with a bdf
which includes a bus number, but it really should not as this routine
only expects a device/function encoding.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Currently pci_bus_read_config() and pci_bus_write_config() are
called with bus number masked off in the parameter bdf, and bus
number is supposed to be added back in the bridge driver's pci
config read/write ops if the device is behind a pci bridge.
However this logic only works for a pci topology where there is
only one bridge off the root controller. If there is addtional
bridge in the system, the logic will create a non-existent bdf
where its bus number gets accumulated across bridges.
To correct this, we change all pci config read/write routines
to use complete bdf all the way up to the root controller.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
In driver model, each pci bridge device has its own hose structure.
hose->first_busno points to the bridge device's device number, so
we should not substract hose->first_busno before programming the
bridge device's primary/secondary/subordinate bus number registers.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Zynq is using Cadence IP where binding is documented in the Linux kernel
and there is no reason to use different binding.
Synchronize it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Increase the Rx Buffer descriptors to 32. This will avoid
Rx buffer descriptors overflow if more packets were received
at one shot before we process the received ones.
This fixes the issue of intermittent timeouts during tftp
on a 1Gb connection with tftp server running on windows.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Flush and invalidate the rx buffers while sending the
tx packet it self as armv8 does flush also while doing
invalidation.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Set the data bus width to 64-bit AMBA Databus width in config register.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Use %p to print pointers.
The max value of (i_buf - i_buf_start) should be dfu_buf_size, which is
an unsigned long, so cast the pointer difference to that type to print.
Change-Id: Iee242df9f8eb091aecfe0cea4c282b28b547acfe
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The MCAST_TFTP support requires that network drivers has mcast functon
implemented. This commit adds dummy keystone2_eth_bcast_addr() to meet
the requirement. As far as the driver doesn't use ALE and doesn't filter
any incoming packets, the function is empty.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Only 2 frequencies are supported. The current driver implementation does
not always use the 2 last configured blink frequencies. This patch
fixes this problem. So that the last two entered frequencies are
active.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tom Rini <trini@konsulko.com>
DCIMVAC is upgraded to DCCIMVAC for the individual processor
(Cortex-A7) that the DCIMVAC is executed on.
We should follow the linux dma follow. Before DMA read, first
invalidate dcache then after DMA read, invalidate dcache again.
With the DMA direction DMA_FROM_DEVICE, the dcache need be
invalidated again after the DMA completion. The reason is
that we need explicity make sure the dcache been invalidated
thus to get the DMA'ed memory correctly from the physical memory.
Any cache-line fill during the DMA operations such as the
pre-fetching can cause the DMA coherency issue, thus CPU get the stale data.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Jason Liu <r64343@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
On some boards the otg is wired up in host-only mode in this case we
have no vbus-det gpio.
Stop logging an error from sunxi_usb_phy_vbus_detect() in this case, and
stop treating sunxi_usb_phy_vbus_detect() returning a negative errno, as
if a charger is plugged into the otg port.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When we return an error the usb core will print an error-message, so in this
case do not print anything.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Modify the sunxi musb glue to use the device-model for musb host mode.
This allows using musb in host mode together with other host drivers
such as ehci / ohci, which is esp. useful on boards which use the
musb controller in host-only mode, these boards have e.g. an usb-a
receptacle or an usb to sata converter attached to the musb controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the musb config and platdata to the sunxi-musb glue, which is where
it really belongs. This is preparation patch for adding device-model
support for the sunxi-musb-host code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
When in host mode check if there is a host cable inserted into the otg
port by checking the id pin. If there is no host cable return an error to
make usb_lowlevel_init() exit early, rather then waiting for 1 second
for a device which will never show up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
