Default value (4000ms) of PHY_ANEG_TIMEOUT for Micrel KSZ9031 contoller
isn't sufficient to finish auto-negotiation, which sometimes leads to
timeout errors:
Apalis iMX6 # dhcp
FEC Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increase the auto-negotiation time-out to 15000ms.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Enable DM Video support on iMX53 M53Menlo and fix minor details
to restore previous behavior of the system.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM block and DM MMC and DM USB support on iMX53 M53Menlo .
Convert board code to match the DM support. This also enables DM
pincontrol to configure the SDHI pins.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable DM GPIO support on iMX53 M53Menlo and fix up board code where
applicable. Enable MALLOC_F to let the GPIO controllers bind early on.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Import iMX53 M53Menlo device tree from Linux next-20190607 3f310e51ceb1 .
Enable DT control in full U-Boot . Add U-Boot extras into separate DTSi,
the GPIO controllers need to be inited early, otherwise m53_set_clock()
won't be able to detect the correct CPU clock frequency by reading the
GPIO.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Synchronize iMX53 device tree from Linux next-20190607 3f310e51ceb1 ,
this is needed to get NFC, UART, USBOTG DT nodes.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Since the pico-pi uses the distroboot,
this commit remove the 'script' variable (cf boot_scripts).
Signed-off-by: Pierre-Jean Texier <pjtexier@koncepto.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
According to hab.c code we have to notify the ROM code if the MMU is
enabled or not. This is achieved by setting the "pu_irom_mmu_enabled"
to 0x1.
The current address in hab.c code is wrong for i.MX6SL, according to ROM
map file the correct address is 0x00901c60.
As we are writing in the wrong address the ROM code is not flushing the
caches when needed, and the following HAB event is observed in certain
scenarios:
--------- HAB Event 1 -----------------
event data:
0xdb 0x00 0x14 0x41 0x33 0x18 0xc0 0x00
0xca 0x00 0x0c 0x00 0x01 0xc5 0x00 0x00
0x00 0x00 0x07 0xe4
STS = HAB_FAILURE (0x33)
RSN = HAB_INV_SIGNATURE (0x18)
CTX = HAB_CTX_COMMAND (0xC0)
ENG = HAB_ENG_ANY (0x00)
Update MX6SL_PU_IROM_MMU_EN_VAR to address this issue.
Reported-by: Frank Zhang <frank.zhang@nxp.com>
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
After the conversion to DM the U-Boot binary is called u-boot-dtb.imx,
so fix the README file accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Joris Offouga <offougajoris@gmail.com>
Fix set_emmcargs wrapper, which prepares proper bootargs for booting
from eMMC.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Add support for loading u-boot FIT images over the USB SDP protocol in
the SPL
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
[Various build fixes]
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
This pull request provides bug fixes for the UEFI sub-system. The most
relevant one concerns the allocation of memory at address 0. It is
needed for booting Linux on several boards via bootefi, e.g. the Asus
TinkerBoard.
An undefined reference bug in disk/part.c related to a division is
resolved.
-----BEGIN PGP SIGNATURE-----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=+IPc
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc5-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5 (2)
This pull request provides bug fixes for the UEFI sub-system. The most
relevant one concerns the allocation of memory at address 0. It is
needed for booting Linux on several boards via bootefi, e.g. the Asus
TinkerBoard.
An undefined reference bug in disk/part.c related to a division is
resolved.
The setexpr shell command calls cmd_get_data_size() which is only built
when CMD_DATA_SIZE is defined. We need to define CMD_DATA_SIZE if
CONFIG_CMD_SETEXPR is selected or the build will fail if no other
command selecting this option is enabled.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
In order to migrate this symbol to Kconfig introduce a new symbol to
guard it, CONFIG_SYS_CUSTOM_LDSCRIPT. When that is set we can then
provide the exact final location o the script.
Signed-off-by: Tom Rini <trini@konsulko.com>
A number of boards set CONFIG_SYS_LDSCRIPT and then end up using one of
the default searched LDSCRIPT paths. Remove these customizations.
Signed-off-by: Tom Rini <trini@konsulko.com>
The non-CONFIG_SPL_FRAMEWORK SPL used on some PowerPC platforms have a
choice between CONFIG_SPL_NAND_BOOT, CONFIG_SPL_MMC_BOOT and
CONFIG_SPL_SPI_BOOT. Migrate this to Kconfig
Signed-off-by: Tom Rini <trini@konsulko.com>
This tool has just been added but it seems I forgot to add it to
the ignore list. So to prevent the built binary being marked as
unversioned, add it to the ignore list.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert CONFIG_TFTP_BLOCKSIZE to Kconfig, update defconfigs,
headers and whitelist.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Convert CONFIG_IP_DEFRAG to Kconfig, update defconfigs, headers
and whitelist. This patch is a follow-up on a patch by Christian
Gmeiner with the added config/header/whitelist updates.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reported-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The SetAttribute() service and the Reset() service of the simple text
output protocol must update the attribute value in the mode information.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Correct the check of the mode number in SetMode() service of the simple
text output protocol.
Clear the screen in SetMode().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This variable is defined in UEFI specification 2.8, section 8.1.
Its value should be updated whenever we add any usable runtime services
function.
Currently we only support SetVirtualAddress() for all systems and
ResetSystem() for some.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Return EFI_INVALID_PARAMETER if the variable name has zero length or the
variable has runtime access but not boottime access.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When compiling with FTRACE=1 an error
ld.bfd: disk/built-in.o: in function `lba512_muldiv':
disk/part.c:114: undefined reference to `__udivmoddi4
occurred.
Use '>> 11' instead of '/ 2048' to avoid the division.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The UEFI specification does not specify if the characters that have to be
replaced by underscore in function StrToFat() of the Unicode collation
protocol are those forbidden in FAT long names or those in FAT short names.
EDK2 and UEFI SCT assume it is those forbidden in FAT 8.3 short names.
Adjust the list of forbidden characters.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
It must be possible to allocate memory at address 0 with AllocatePages().
Move a NULL pointer check.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If an image already has been started, return EFI_INVALID_PARAMETER when
StartImage() is called for the same handle again.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Change my email address, too many mails
gets to my private mail, created specific email
account just for developmement.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
Last change to this board was done in 2016, has no prospects of
ever being converted to DM, drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro.uh@renesas.com>
This provides an SPL_SIZE_LIMIT that makes the build check that the SPL
binary loaded from flash fits into the SRAM (64 KiB) and leaves enough
room for global data, heap and stack (512 bytes assumed stack usage).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QA+5
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190612' of git://git.denx.de/u-boot-amlogic
- pinctrl: meson-gx: fix GPIO_TEST_N and GPIOCLK_ groups
- pinctrl: meson-gxbb: add hdmi related pins to fix HDMI on GXBB
- pinctrl: meson: add support for getting pinmux status
- pinctrl: meson-g12a: add support for drive-strength-microamp property
The GXBB pinctrl is missing pins related to HDMI, namely hot plug
detection (hpd) and I2C (sda + scl).
This fixes HDMI support for GXBB in u-boot.
Reported-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Mohammad Rasim <mohammad.rasim96@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
add drive-strength bank regiter and bit value for G12A SoC
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
drive-strength-microamp is a new feature needed for G12A SoC.
the default DS setting after boot is usually 500uA and it is not enough for
many functions. We need to be able to set the drive strength to reliably
enable things like MMC, I2C, etc ...
Signed-off-by: Guillaume La Roque <glaroque@baylibre.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
