We are now using an env_ prefix for environment functions. Rename these
other functions as well, for consistency:
getenv_vlan()
getenv_bootm_size()
getenv_bootm_low()
getenv_bootm_mapsize()
env_get_default()
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
commonly used functions, for consistency. Also add function comments in
common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename setenv()
for consistency. Also add function comments in common.h.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
The IPU AXI QoS for the i.MX6QP and i.MX6DP processors have to be set as
commented in the code:
/* set IPU AXI-id1 Qos=0x1 AXI-id0/2/3 Qos=0x7 */
Set IOMUXC_GPR6 and IOMUXC_GPR7 to 0x77177717 instead of 0x007F007F.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Use the env_save() function directly now that there is only one
implementation of saveenv().
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This is a strange name for a function that loads the environment. There is
now only one implementation of this function, so use the new env_load()
function directly instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present we support multiple environment drivers but there is not way to
select between them at run time. Also settings related to the position and
size of the environment area are global (i.e. apply to all locations).
Until these limitations are removed we cannot really support more than one
environment location. Adjust the location to be a choice so that only one
can be selected. By default the environment is 'nowhere', meaning that the
environment exists only in memory and cannot be saved.
Also expand the help for the 'nowhere' option and move it to the top since
it is the default.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Move all of the imply logic to default X if Y so it works again]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix USB OTG power enable aka USBO1_EN which on Apalis T30 is connected
to the T30 ball GEN2_I2C_SCL.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
At present we have three states for the environment, numbered 0, 1 and 2.
Add an enum to record this to avoid open-coded values.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
About a quarter of the files in common/ relate to the environment. It
seems better to put these into their own subdirectory and remove the
prefix.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
OLimex A64-OLinuXino is an open-source hardware board
using the Allwinner A64 SOC.
OLimex A64-OLinuXino has
- A64 Quad-core Cortex-A53 64bit
- 1GB or 2GB RAM DDR3L @ 672Mhz
- microSD slot and 4/8/16GB eMMC
- Debug TTL UART
- HDMI
- LCD
- IR receiver
- 5V DC power supply
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi A64 is a new board of high performance with low cost
designed by FriendlyElec., using the Allwinner A64 SOC.
Nanopi A64 features
- Allwinner A64, 64-bit Quad-core Cortex-A53@648MHz to 1.152GHz, DVFS
- 1GB DDR3 RAM
- MicroSD
- Gigabit Ethernet (RTL8211E)
- Wi-Fi 802.11b/g/n
- IR receiver
- Audio In/Out
- Video In/Out
- Serial Debug Port
- microUSB 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
If CONFIG_MMC_DW is not defined the return value of
init_dwmmc should not rely on a random stack value.
Instead indicate that no error occured.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
With SPL_LDSCRIPT moved to Kconfig (and this being a 'string' config
node), all the lingering definitions in header files will cause
warnings/errors due to the redefinition of the configuration item.
As we don't want to pollute the defconfig files (and values should
usually be identical for entire architectures), the defaults are moved
into Kconfig. Kconfig will always pick the first default that
matches, so please keep these values at the end of each file (to allow
any board-specific Kconfig, which will be included earlier) to
override with an unconditional default setting.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the debug uart is marked as dm-pre-reloc, the pinctrl driver
will handle the correct iomux setting.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reasonably robust way (this will be needed so early that
diagnostics will be limited) to specify the base-address of the secure
timer through the DTS for TPL and SPL. In order to allow us a cleaner
way to structure our SPL and TPL stage, we now move to a DM timer
driver.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
prefix the bl31 firmware needed to build uboot.itb so it can coexist in
the build area with ATFs from other boards (i.e. lion_rk3368)
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The ITS file generated warnings due to @<num> designations in the naming
which cause DTC to complain as follows:
Warning (unit_address_vs_reg): Node /images/uboot@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /images/atf@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /images/pmu@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /images/fdt@1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /configurations/conf@1 has a unit name, but no reg property
This removes the @<num> part from the names, as we only have a single
image for each payload aspect (and only a single configuration) anyway.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3368-uQ7 (codenamed 'Lion') is a micro-Qseven (40mm x 70mm,
MXM-230 edge connector compatible with the Qseven specification)
form-factor system-on-module based on the octo-core Rockchip RK3368.
It is designed, supported and manufactured by Theobroma Systems.
It provides the following features:
- 8x Cortex-A53 (in 2 clusters of 4 cores each)
- (on-module) up to 4GB of DDR3 memory
- (on-module) SPI-NOR flash
- (on-module) eMMC
- Gigabit Ethernet (with an on-module KSZ9031 PHY)
- USB
- HDMI
- MIPI-DSI/single-channel LVDS (muxed on the 'LVDS-A' pin-group)
- various 'slow' interfaces (e.g. UART, SPI, I2C, I2S, ...)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch brings the OMAP3 EVM to a bootable state, on master, as of
v2017.09-rc1.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_MAX6957
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Traditional KS2 devices supported NAND via the AEMIF peripheral. However,
66AK2G doesn't use the AEMIF but rather the GPMC for NAND. Therefore,
clarify some statements to indicate only certain devices have AEMIF and
in other places just say NAND instead of AEMIF NAND
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Roger Quadros <rogerq@ti.com>
The 512 MB DDR version of SOM's use CS0 and CS1. CS1 is not correctly
setup in the pin muxing. This causes erratic behavior on suspend/resume
This fix has been tested on both 256 and 512 MB DDR versions.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch adds support for the Olimex OLinuXino Lime2 with eMMC flash
storage.
https://www.olimex.com/Products/OLinuXino/A20/A20-OLinuXino-LIME2-eMMC/
It is a assembly variant of the regular Lime2 but featuring eMMC for
storage.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The implementation of function set_pcie_ns_access() uses a wrong
argument. The structure array ns_dev has a member 'ind' which is
initialized by CSU_CSLX_*. It should use the 'ind' directly to
address the PCIe's CSL register (CSL_base + CSU_CSLX_PCIE*).
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
IFC and QSPI are muxed on board. Add fsl_fdt_fixup_flash() to disable
IFC node in dts if QSPI is enabled, or disable QSPI node in dts if
otherwise.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Function enable_layerscape_ns_access() is alreayd called soc-wide.
Remove duplicated calling from individual boards.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[YS: Add commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Function config_board_mux() reads env variable 'hwconfig' which is
only available after relocation for QSPI boot. Move calling
config_board_mux() to misc_init_r().
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Smart voltage translator is removed from LS2080ARDB/LS2088ARDB
RevF boards. It is only used on LS2081ARDB. Programming GPIO
is only required for LS2081ARDB.
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
[YS: Revise commit message]
Reviewed-by: York Sun <york.sun@nxp.com>
Update the default core frequency to 1800MHZ for best performance under
SD boot and eMMC boot.
Signed-off-by: Gong Qianyu <Qianyu.Gong@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The driver is for all boards 24XX and up, so let's eliminate the
extra option called CONFIG_SYS_I2C_OMAP34XX since the driver checks
for CONFIG_OMAP34XX we don't need CONFIG_SYS_I2C_OMAP34XX.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This defconfig uses the PCIe x4 binary blobs from the congatec BIOS.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the infrastructure to define different config headers
with different configurations and default environment for the baseboards
that can now be selected via Kconfig. The new configuration for the
theadorable-x86-conga-qa3-e3845 is also added. Also the new defconfig
file for this new target is added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch adds the infrastructure to define different config headers
with different configurations and default environment for the baseboards
that can now be selected via Kconfig. The new configuration for the
theadorable-x86-dfi-bt700 is also added.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The I2C reading in the PEX vs SATA detection code often fails on the
first try. Try three times, as the code for EEPROM reading does.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and driver
model. The peripheral clock and pins configuration are handled by
the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To support driver model and device tree, use the SPI-flash-based
AT45xxx DataFlash driver, DataFlash is a kind of SPI flash.
Instead of ATMEL_DATAFLASH_SPI DataFlash older driver that will
be removed in the future.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the dts files to support deivce tree, update the configuration
files to support the device tree and driver model. The peripheral
clock and pins configuration are handled by the clock and the pinctrl
drivers respectively.
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@microchip.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The logic of what fdt_get_base_address() will search for and return has
changed. Rework get_phys_ccsrbar_addr_early() to perform the logic that
fdt_get_base_address used to perform.
Fixes: 336a44877a ("fdt: Correct fdt_get_base_address()")
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add initial support for the R8A7795 and R8A7796 based ULCB board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for Phytec pfla02, equipped with NAND.
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 31C
Reset cause: POR
I2C: ready
DRAM: 1 GiB
NAND: 2048 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected n25q128 with page size 256 Bytes, erase size 64 KiB, total
16 MiB
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Stefan Christ <s.christ@phytec.de>
CC: Stefan Müller-Klieser <S.Mueller-Klieser@phytec.de>
CC: Christian Hemp <C.Hemp@phytec.de>
strncat(a, b, c) appends a maximum of c characters plus the 0 byte
to a.
In board_init we first write 4 characters plus 0 byte to version.
So only ZYNQMP_VERSION_SIZE - 5 additional characters fit into
version.
The problem was indicated by cppcheck.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Modify chip_id() routine such that to handle based on
the current el. Also make it available even if FPGA is
not enabled in system such it can be used always.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch makes chip_id() as a global routine so that
it can be used in other places as required.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch modifies the chip_id routine to get either idcode or
silicon version based on the argument received.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove incorrect code of writing to system timestamp
counter registers. This register writes does nothing
and can be removed.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Newer psu_init_gpl.c/h contain clock setup. Detect if
reference clock is active. If yes, skip timer setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is a need to include psu_init also in mini u-boot configuration
that's why handle psu_init via Kconfig property.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
For some mini platforms there could be a need to include psu_init.
That's why move it to board file instead of spl only file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable validation of boot.scr script prior to its execution dependent
on "secureboot" flag in environment. Disable fall back option to
nor/qspi boot in case of secure boot. Also enable "secureboot=y"
flag in environment for ARM based platforms instead of bootcmd.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Tested-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Only a specific type of SPI flash exists on a board, having board
Kconfig to select the SPI flash seems to make more sense. Other
flash types are not necessary except coreboot, which implies all
available flash drivers there.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is architecture-dependent early initialization hence should
be put in the platform Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_BOARD_EARLY_INIT_F literally indicates board-specific codes
and should be not 'default y' for all x86 boards.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is not used in SPL so we do not need to compile it. Make this change
before adding driver-model support to the driver, to avoid build errors.
With driver model we define a U_BOOT_DRIVER() which would otherwise be
present in SPL and not be garbage-collected when building.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When we have MMC available we assume that we want to put the env as a
file on FAT.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Change from EHCI to xHCI on the DFI BayTrail SoM.
The xHCI USB hub is connected to an GPIO on the DFI BayTrail SoM. For
correct operation, it needs to get reset upon power-up. Otherwise it
may happen that the hub is not detected after a software reboot. This
patch also configures this GPIO in the dts for correct operation.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This config option is needed on the congatec x86 BayTrail board, as
otherwise the USB hub will not get initialized correctly. This
patch selects this Kconfig option again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add Intel Edison board which is using U-Boot.
The patch is based on work done by the following people (in alphabetical
order):
Aiden Park <aiden.park@intel.com>
Dukjoon Jeon <dukjoon.jeon@intel.com>
eric.park <eric.park@intel.com>
Fabien Chereau <fabien.chereau@intel.com>
Felipe Balbi <felipe.balbi@linux.intel.com>
Scott D Phillips <scott.d.phillips@intel.com>
Sebastien Colleur <sebastienx.colleur@intel.com>
Steve Sakoman <steve.sakoman@intel.com>
Vincent Tinelli <vincent.tinelli@intel.com>
In case we're building for Intel Edison, we must have 4096 bytes of
zeroes in the beginning on u-boot.bin. This is done in
board/intel/edison/config.mk.
First run sets hardware_id environment variable which is read from
System Controller Unit (SCU).
Serial number (serial# environment variable) is generated based on eMMC
CID.
MAC address on USB network interface is unique to the board but kept the
same all over the time.
Set mac address from U-Boot using following scheme:
OUI = 02:00:86
next 3 bytes of MAC address set from eMMC serial number
This allows to have a unique mac address across reboot and flashing.
Signed-off-by: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[bmeng: Add MAINTAINERS file for Intel Edison board]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Convert this PMIC driver to driver model and fix up other users. The
regulator and GPIO functions are now handled by separate drivers.
Update nyan-big to work correct. Three boards will need to be updated by
the maintainers: apalis-tk1, cei-tk1-som. Also the TODO in the code re
as3722_sd_set_voltage() needs to be completed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
A few lines (defines and declarations) had been duplicated when the
puma-rk3399 board was initially merged. This removes the duplicates
and changes the style to use local constants instead of pasted
literals.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
[fixed up commit-message & converted to use 'const u32':]
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Migrate all FMC defines from arch/arm/include/asm/arch-stm32f7/fmc.h
to drivers/ram/stm32_sdram.c
This will avoid to add an additionnal arch-stm32xx/fmc.h file when
a new stm32 family soc will be introduced.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allow to remove include/dm/platform_data/serial_stm32x7.h
which was included in the past by stm32x7 driver and by
stm32f746-disco.c board file.
Since patch 42bf5e7c27 "serial: stm32f7: add device tree support"
this file is no more needed in board file.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
BeagleBoard X15 revC board is similar to X15 revB1 except
with a SR2.0 where revB1 uses a SR1.1. Add board detection
support for revC.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
board_is*("rev", board_ti_get_rev()) uses strncmp() for
revison detection and assumes it is success if return value
is <= 0. This will fail in case of multiple versions, as
revb will be true for board_is_*revb() and board_is_*reva().
Fix it by looking for exact match of the string.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE
In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.
In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.
There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with
./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC
And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
It is possible to flag MAC addresses as locally administred. In this
case they don't need to be unique. This is only allowed for interfaces
which have no connection to the outside. For the TEGR1 board we use
this feature.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
If we rebrand the IVM and ethaddr was set previously we need to change
ethaddr. Otherwise we end up with a wrong MAC adress for the ethernet
interface.
Cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Since commit ce412b79e7 ("drivers: net: phy: atheros: add separate
config for AR8031") Ethernet does not work on mx6sabreauto.
This commit correctly assigns ar8031_config() as the configuration
function for AR8031 in the same way as done in the Linux kernel.
However, on mx6sabreauto design we need some additional configurations,
such as enabling the 125 MHz AR8031 output and setting the TX clock
delay that need to be done in the board file.
This is the equivalent fix from commit 4b6035da48 ("mx6sabresd: Make
Ethernet functional again").
Reported-by: Miquel RAYNAL <miquel.raynal@free-electrons.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for Falcon mode and explain in the README the steps to
boot the kernel directly without loading the full U-Boot.
Signed-off-by: Diego Dorta <diego.dorta@nxp.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
WEIM cannot be used when I2C3 is enabled due to pin conflict, so keep
WEIM disabled by default.
I2C3 controls GPIO I2C expander (USB host and OTG have VBUS controlled by
the GPIO I2C expander), magnetometer, accelerometer.
Not disabling WEIM in U-Boot causes I2C3 to behave badly when booting
a NXP 4.1 kernel, which leads to probe failure on several devices,
including the lack of USB:
imx_usb 2184000.usb: Can't register ci_hdrc platform device, err=-517
By keeping WEIM disabled in U-Boot these kernel issues are gone.
Reported-by: Takashi Matsuzawa <tmatsuzawa@xevo.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
CONFIG_SYS_FSL_ESDHC_FORCE_VSELECT is not the correct method
to set I/O to 1.8. To boards that does not support vqmmc-supply,
use vs18_enable in fsl_esdhc_cfg. If regulator is supported,
use fixed 1.8V regulator for vqmmc-supply.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
As mx6sabreauto supports SPL now, all variants can boot using the same
defconfig.
This patch:
- Removes non-SPL targets.
- Renames target to mx6sabreauto_defconfig.
- Renames folder and board files to mx6sabreauto.
- Updates MAINTAINERS, Makefile and Kconfig accordingly.
- Removes .cfg files.
- Adds a README with instructions to build and flash SPL and u-boot.img.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add support for mx6q, mx6dl and mx6qp sabreauto boards in SPL.
Retrieved the mx6q DCD table from:
board/freescale/mx6qsabreauto/imximage.cfg
Retrieved the mx6dl DCD table from:
board/freescale/mx6qsabreauto/mx6dl.cfg
Retrieved the mx6qp DCD table from:
board/freescale/mx6qsabreauto/mx6qp.cfg
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabreauto boards.
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The Cubox-i and Hummingboard series of devices have an option of
SATA on board, and depending on how the fuses are blown even the
option to boot SPL from SATA. So enable support for it so it can
be used to boot the OS from if people desire.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
This change sets the VLDO4 settings output to 2.8V in PMIC
initialization so that the MIPI DSI/CSI input voltage is 2.8V
as per the schematics. The original code provides an output of
3.3V which violates the voltage mentioned in the schematics.
Signed-off-by: Gautam Bhat <mindentropy@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@nxp.com>
imx6qdl_icore_mmc_defconfig => imx6qdl_icore_rqs_defconfig
Since icorem6_rqs support MMC/eMMC boot, so doesn't need
to name it explicitly.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
There is no need to add a 100us delay after the DDR initialization.
Other imx6 boards do not have such delay either, so simply remove it.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The Turris Omnia is a open-source router created by CZ.NIC.
The code is based on the Marvell/db-88f6820-gp by Stefan Roese
with modifications from Tomas Hlavacek in the CZ.NIC turris-omnia-uboot
repository, which can be found at
https://gitlab.labs.nic.cz/turris/turris-omnia-uboot
By default, the Turris Omnia uses btrfs as the main and only filesystem,
and also loads kernel and device tree from this filesystem. Since U-Boot
does not yet support btrfs, you should not flash your Turris Omnia board
with this unless you know what you are doing.
Signed-off-by: Tomas Hlavacek <tomas.hlavacek@nic.cz>
Signed-off-by: Marek Behun <marek.behun@nic.cz>
create mode 100644 board/CZ.NIC/turris_omnia/Makefile
create mode 100644 board/CZ.NIC/turris_omnia/kwbimage.cfg
create mode 100644 board/CZ.NIC/turris_omnia/turris_omnia.c
create mode 100644 configs/turris_omnia_defconfig
create mode 100644 include/configs/turris_omnia.h
Signed-off-by: Stefan Roese <sr@denx.de>
The DDR3 training code for Marvell A38X currently computes 1t timing
when given board topology map of the Turris Omnia, but Omnia needs 2t.
This patch adds support for enforcing the 2t timing in struct
hws_topology_map, through a new enum hws_timing, which can assume
following values:
HWS_TIM_DEFAULT - default behaviour, compute whether to enable 2t
from the number of CSs
HWS_TIM_1T - enforce 1t
HWS_TIM_2T - enforce 2t
This patch also sets all the board topology maps (db-88f6820-amc,
db-88f6820-gp, controlcenterdc and clearfog) to have timing set to
HWS_TIM_DEFAULT.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
As part of preparation for nand DM conversion the new API has been
introduced to remove direct access to nand_info array. So, use it here
instead of accessing to nand_info array directly.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The 'mode' parameter is actually a flag to determine whether to display
a list of devices found during the scan. Rename it to reflect this, add a
function comment and adjust callers to use a boolean.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is not a very useful name since once it is probed it still hangs
around. With driver model we will use uclass data for this, so rename the
struct.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CMD_SATA enables the 'sata' command which also brings
in SATA support. Some boards may wish to enable SATA without the command.
Add a separate CONFIG to permit this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The instructions for creating a disk image that are presently in
README.sandbox fail because sfdisk doesn't know about GPT.
Signed-off-by: Alison Chaiken <alison@peloton-tech.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Enable all the boot-on regulator in default.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Probe dwc2 udc in the function of board_usb_start to enable
usb gadget function.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The bank0 ram size should be the DRAM size minus reserved size,
the DRAM size may be 1GB, 2GB, 4GB, we can not hard code it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added DECLARE_GLOBAL_DATA_PTR for RK3328, RK3368 and RK3399:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
K2G ICE evm will have its own dtb. Therefore, add it to the list of dtbs
located in the appended U-boot dtb FIT image. Therefore, when swapping out
dtbs K2G ICE boards can grab the correct one.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG to allow "board_name" to
be set depending on the board it is being ran on.
Update findfdt to use this new dynamic board_name value to determine
which dtb should be used.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Certain peripherals used by K2G GP aren't used on K2G ICE evm. Or
configuration is slightly different. Therefore, use board detection to
deal with these variations.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some code doesn't apply to K2G ICE evm. Therefore, use board detection to
wrap these calls.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration settings used by the K2G ICE evm. Also use board
detection to determine which DDR3 configuration to use.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add basic pinmux data for new K2G ICE evm. Also add pinmuxing for a
generic K2G evm which includes I2C 0 and 1 used for board detection
purposes.
Since multiple K2G boards are supported that means initially generic
pinmuxing should be used when board detection hasn't ran. Once board
detection runs the proper pinmuxing can be reran to match the board
being ran on.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a function that can be used to determine if the board being ran on is
a K2G Industrial Communication Engine EVM or K2G General Purpose EVM based
on values programmed on the EEPROM.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some K2G evms have their EEPROM programming while most do not. Therefore,
add EEPROM board detection to be used as the default method and fall back
to the alternative board detection when needed.
Also reorder board configuration. Perform bare minimal configuration
initially since board detection hasn't ran. Finish board configuration
once the board has been identified.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now with support for U-boot runtime dtb selection each board needs to
define board_fit_config_name_match so U-boot can determine what the
correct dtb is within the FIT blob.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
For K2G, runtime DTB selection utilizes the embedded_dtb_select function.
Therefore, define the function which will perform a EEPROM read and then
retries selecting the correct dtb now that it can detect which board its
on. For other Keystone devices use an empty function since they will still
use the embedded FIT functionality but their FIT will only contain a single
dtb.
Most production K2G boards do not have their EEPROM programmed. Therefore,
perform a test to verify a K2G GP is currently being used and if it is then
set the values normally set by a EEPROM read.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When the EEPROM is first read its contents are stored in memory as a
cache to avoid further I2C operations. To determine if the EEPROM was
previously read the easiest way is to check the memory to see if the
EEPROM's magic header value is set. Create a new function that can
determine if the EEPROM was previously read or not without having to
perform a I2C transaction.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In some situations the EEPROM used for board detection may not be
programmed or simply programmed incorrectly. Therefore, it may be
necessary to "simulate" reading the contents of the EEPROM to set
appropriate variables used in the board detection code.
This may also be helpful in certain boot modes where doing i2c reads
may be costly and the config supports running only a specific board.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Franklin S Cooper Jr. <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It's been a while since I've touched U-Boot on the Raspberry Pi and
other things have been taking my time. Drop my maintainership for this
port.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The 82xx board mgcoge3ne was removed from the codebase, so this is dead
code.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Discern the SoMs based on the presence of SPI flash to support both
variants of the SoM, one booting from SPI NOR and one booting from
eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Continue loading U-Boot from MMC2 when the SPL was loaded using SAM-BA
loader. This allows the board to boot system from the removable media
instead of the eMMC, which is useful for commissioning purposes. When
booting from the eMMC, always boot from it as it is not possible to
boot from the SD interface directly.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The SDHCI1 is the primary boot controller on rev. 2.1 SoM, which
is the version available on the market. Swap the controller order
to match this and future versions of the SoM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Init the controllers, otherwise the board cannot boot from SD/MMC.
This boot option is new on rev. 2.1 SoM .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
The CAN controllers need slight delay between toggling of their reset
line. Move this action into board_init(), otherwise timer will not be
initialized and the board might hang.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
According to the datasheet, sequential mapping is used for DDR
SDRAM, while interleaved mapping is used for regular SDRAM.
Incorrect configuration of this bit does indeed cause sporadic
memory instability.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Bießmann <andreas.devel@googlemail.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit 842778a091 dfu-util shows serial="UNDEFINED".
to see here again a serial number, we have to call
g_dnl_set_serialnumber().
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Otherwise the loaded image would miss the efi_runtime sections, and fall
over hard when grub (for example) tried to call runtime services located
in this section.
Signed-off-by: Rob Clark <robdclark@gmail.com>
On the controlcenterd_36BIT_SDCARD config we get a warning about
prg_stage1_prepare being unused. Move the declaration closer to usage
and hide under the existing #if tests.
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
GPIO bank E pin 8 & 9 are used to control the on-board two USB ports
VBUS on/off. Let's configure them in the misc_init_r().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init* contain sleep.h header which is not present in u-boot.
Instead of keep comment sleep.h in psu_init* it is easier to add empty
file which is included.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
since commit
'd5abcf94c7123167725fc22ace342f0d455093c1' -
ti: boot: Register the MMC controllers in SPL in the same way as in u-boot
MMC boot on brxre1 board is broken, with this commit we make our board
working again.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Enable DHCP command by default. Move environmental variable location
to before U-Boot image. Enlarge reserved mem for malloc. Update
maintainer.
Signed-off-by: York Sun <york.sun@nxp.com>
commit 0650798824 ("board: am335x: Introduce scale_vcores")
updated voltages of each board based on efuse. It updated
beagle bone specific voltages under the condition board_is_bone().
But this is true only for BeagleBoneWhite. Due to which voltages
are not configured for BBB, BBW as wrong device is being probed.
So create a common function board_is_beaglebonex() which includes
am335x based beagle family. Use this for updating voltages.
Also remove extra if condition for selecting voltages which is
done later using a switch case and match usb current limit as
before the commit 0650798824.
Fixes: 0650798824 ("board: am335x: Introduce scale_vcores")
Reported-by: Emmanuel Vadot <manu@bidouilliste.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
One can obtain those variables using next commands:
$ fastboot getvar cpu
$ fastboot getvar secure
$ fastboot getvar board_rev
$ fastboot getvar userdata_size
Those variables are needed for fastboot.sh script.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM572x-evm using latest PMT[1] and the
board files named am572x_gp_evm_A3a_sr2p0 and am572x_gp_evm_A2b_sr1p1
that were autogenerated on 30th January, 2017 by
"Ahmad Rashed <a-rashed@ti.com>" and "Tom Johnson <thjohnson@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM571x-IDK board using latest PMT[1] and the
board files named am571x_idk_v1p3b_sr2p0 that were autogenerated on
23rd March, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Update the board pinmux for AM572x-IDK board using latest PMT[1] and the
board files named am572x_idk_v1p3b_sr2p0 that were autogenerated on
30th January, 2017 by "Ahmad Rashed <a-rashed@ti.com>" and
"Tom Johnson <thjohnson@ti.com>".
[1] https://dev.ti.com/pinmux/app.html#/default/
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add ddr voltage rail (dcdc3) configuration. Set the dcdc3
DDR supply to 1.35V.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The SoPine is a SoM by Pine64, with an Allwinner A64 SoC, a LPDDR3 DRAM
chip, an AXP803 PMIC, a SPI NOR Flash and a MicroSD slot. The card
detect pin of the MicroSD slot is broken, however, it doesn't matter as
the design of SoPine didn't allow hot-swapping the MicroSD card (The
MicroSD slot is at the back of the SoM, and when the SoM is installed on
the baseboard, it's nearly impossible to remove the MicroSD).
The official baseboard of it is a board with nearly the same connectors
with the original Pine64+, with the MicroUSB power jack replaced, and
at the position of MicroSD slot a eMMC module slot is added.
Add support for SoPine with the official baseboard by adding its
defconfig file. It still uses the device tree of Pine64, however, it
will change after a proper device tree of SoPine with baseboard is
accepted by Linux mainline.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[Update board/sunxi/MAINTAINERS]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The usb_gadget_handle_interrupts()-function is already implemented by
drivers/usb/gadget/dwc2_udc_otg.c, so we need to avoid defining it
in the evb-rk3328.c board-specific file.
This change fixes the following build error (from buildman):
drivers/usb/gadget/built-in.o: In function `usb_gadget_handle_interrupts':
build/../drivers/usb/gadget/dwc2_udc_otg.c:850: multiple definition of `usb_gadget_handle_interrupts'
board/rockchip/evb_rk3328/built-in.o:build/../board/rockchip/evb_rk3328/evb-rk3328.c:37: first defined here
make[1]: *** [u-boot] Error 1
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Update maintainer to Kever Yang for William Zhang is not
work for this board now.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Generate a MAC address based on the cpuid available in the efuse
block: Use the first 6 byte of the cpuid's SHA256 hash and set the
locally administered bits. Also ensure that the multicast bit is
cleared.
The MAC address is only generated and set if there is no ethaddr
present in the saved environment.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With our efuse driver for the RK3399 ready, we can add the
board-specific code that consumes the cpuid from the efuse block and
postprocesses it into the system serial (using the same CRC32 based
derivation as in Linux).
We expose the cpuid via two distinct environment variables:
serial# - the serial number, as derived in Linux
cpuid# - the raw 16 byte CPU id field from the fuse block
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
Disable SDRAM controller EMIF2 for single core SOC
Set SDRAM size size to 1GB
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Tom Rini <trini@konsulko.com>
The declarations should not be in common.h. Move them to the arch-specific
headers.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Fixup thinko defined(FSL_LSCH3) -> defined(CONFIG_FSL_LSCH3)]
Signed-off-by: Tom Rini <trini@konsulko.com>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
- Switch to using <configs/ti_armv7_omap.h> and family. This lets us
drop lots of custom defines.
- Ensure that our default environment uses DEFAULT_LINUX_BOOT_ENV so
that Linux will boot correctly.
- Enable CONFIG_DISTRO_DEFAULTS
- Switch to using CONFIG_OF_CONTROL
- Various other cleanups to match other SoCs in the family line.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ti816x/am389x SoC is the first generation in what U-Boot calls the
"am33xx" family. In the first generation of this family the DDR
initialization sequence is quite different from all of the subsequent
generations. Whereas with ti814x (second generation) we can easily work
the minor differenced between that and am33xx (third generation), our
attempts to do this for ti816x weren't sufficient. Rather than add a
large amount of #ifdef logic to make this different sequence work we add
a new file, ti816x_emif4.c to handle the various required undocumented
register writes and sequence and leverage what we can from
arch/arm/mach-omap2/am33xx/ddr.c still. As DDR2 has similar problems
today but I am unable to test it, we drop the DDR2 defines from the code
rather than imply that it works by leaving it. We also remove a bunch
of other untested code about changing the speed the DDR runs at.
Signed-off-by: Tom Rini <trini@konsulko.com>
Orangepi Prime is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Prime has
- Quad-core Cortex-A53
- 2GB DDR3
- Debug TTL UART
- 1000M/100M Ethernet RJ45
- Three USB 2.0
- HDMI
- Audio and MIC
- Wifi + BT
- IR receiver
- HDMI
- Wifi + BT
Boot from MMC:
-------------
U-Boot SPL 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00662-ga3f4c05-dirty (May 25 2017 - 13:30:14 +0000) Allwinner Technology
CPU: Allwinner H5 (SUN50I)
Model: OrangePi Prime
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: phy interface7
eth0: ethernet@1c30000
starting USB...
USB0: USB EHCI 1.00
USB1: USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When U-Boot boots from EL2, skip some lowlevel init code requiring
EL3, including CCI-400/CCN-504, trust zone, GIC, etc. These
initialization tasks are carried out before U-Boot runs. This applies
to the RAM version image used for SPL boot if PPA is loaded first.
Signed-off-by: York Sun <york.sun@nxp.com>
DPAA2 platforms boot the Management Complex based on the u-boot env
variable "mcinitcmd". Instead of doing this step on each platform
individually, define a single mc_env_boot function in the MC driver,
since it's semantically tied to it.
Call the function in a per-board reset_phy hook, as it gets called at a
later moment, when all board PHY devices have been initialized.
Signed-off-by: Bogdan Purcareata <bogdan.purcareata@nxp.com>
Signed-off-by: Heinz Wrobel <heinz.wrobel@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a sandbox board to test the non-livetree build (i.e. with
CONFIG_OF_FLAT disabled). This increases our build and test coverage.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable CONFIG_DM_MMC_OPS and CONFIG_BLK for all Tegra devices. This moves
Tegra to use driver model fully for MMC.
Signed-off-by: Simon Glass <sjg@chromium.org>
This header includes things that are needed to make driver build. Adjust
existing users to include that always, even if other dm/ includes are
present
Signed-off-by: Simon Glass <sjg@chromium.org>
BPI-M64 is a 64-bit quad-core mini single board computer
using the Allwinner A64 SOC.
BPI-M64 features
- 1.2 Ghz Quad-Core ARM Cortex A53
- 2GB DDR3 SDRAM with 733MHz
- MicroSD/eMMC(8GB)
- 10/100/1000Mbps ethernet (Realtek RTL8211E/D)
- Wifi + BT
- IR receiver
- Audio In/Out
- Video In/Out
- 5V 2A DC power-supply
For dts file,
Sync with Linux commit 4879b7ae("Merge tag 'dmaengine-4.12-rc1'").
Boot from MMC:
-------------
U-Boot SPL 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31)
DRAM: 2048 MiB
Trying to boot from MMC1
NOTICE: BL3-1: Running on A64/H64 (1689) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NOTICE: BL3-1: v1.0(debug):aa75c8d
NOTICE: BL3-1: Built : 18:28:27, May 24 2017
NOTICE: Configuring AXP PMIC
NOTICE: PMIC: setup successful
INFO: BL3-1: Initializing runtime services
INFO: BL3-1: Preparing for EL3 exit to normal world
INFO: BL3-1: Next image address: 0x4a000000, SPSR: 0x3c9
U-Boot 2017.05-00667-g85dd258-dirty (May 29 2017 - 13:07:31 +0000) Allwinner Technology
CPU: Allwinner A64 (SUN50I)
Model: BananaPi-M64
DRAM: 2 GiB
MMC: SUNXI SD/MMC: 0, SUNXI SD/MMC: 1
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently these (board agnostic) commands cannot be selected using
menuconfig and friends. Fix this the obvious way. As part of this,
don't muddle the meaning of CONFIG_HASH_VERIFY to mean both 'hash -v'
and "we have a hashing command" as this makes the Kconfig logic odd.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
[trini: Re-apply, add imply for a few cases, run moveconfig.py, also
migrate CRC32_VERIFY]
Signed-off-by: Tom Rini <trini@konsulko.com>
Engicam has several SOM's on i.MX6 stream, where each SOM
has one include/configs/*.h file, this patch generate single
config file for all SOM's include/configs/imx6-engicam.h
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The maximum SD clock frequency in High Speed mode is 50 MHz. This change
makes it possible to get 48 MHz from the USB PLL (240 MHz / 5 / 1)
instead of the previous 33.25 MHz from the AHB clock (133 MHz / 2 / 2).
Signed-off-by: Benoît Thébaudeau <benoit@wsystem.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add the initial support for pico-imx7d board based on Wig Cheng's
source code.
Add support for eMMC, USB gadget, I2C, PMIC and Ethernet.
For more information about this board, please visit:
http://www.technexion.org/products/pico/pico-som/pico-imx7-emmc
Signed-off-by: Vanessa Maegima <vanessa.maegima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Use GPIO19 which is wired to the uSOM phy reset signal in order to reset
the uSOM's 1512 Gigabit Ethernet phy.
This GPIO is valid on ClearFog rev 2.1 and newer.
Taken from SolidRun's specialised u-boot, see
f906e3df17
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Stefan Roese <sr@denx.de>
NanoPi M1 is a board based on Allwinner H3 CPU.
This commit adds the support for this platform with:
- an include device tree which enables UART, LEDs, GPIO key switch,
1 USB host ports and the SD-card as a dtsi file.
- a device tree specific to this board that enables the
2 additional USB ports
- a defconfig file for minimal support
- a section in MAINTAINERS (add myself)
Synchronized with the kernel device tree, from commits:
sun8i-nanopi.dtsi: 85d2913614d9ab899d23b7ab7d22d23cf45bd1de
sun8i-h3-nanopi-m1.dts: 10efbf5f16336b7540ad6a16aa1cb0b26bab033b
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adjusts memory map for secure boot headers on LS2080AQDS
and LS2080ARDB platforms. Secure boot headers are placed on NOR
flash at offset 0x00600000.
Signed-off-by: Udit Agarwal <udit.agarwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch is to adjust the memory mapping for FLash/SD card on
LS1046AQDS and LS1046ARDB, such as FMAN firmware load address, U-Boot
start address on serial flash and environment address.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QSPI-boot is supported on LS2088ARDB RevF board with LS2088A SoC.
LS2088ARDB RevF Board has limitation that QIXIS can not be accessed.
CONFIG_FSL_QIXIS is not enabled.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Suresh Gupta <suresh.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Update QIXIS related code to be executed only if CONFIG_FSL_QIXIS
flag is enabled. In case QIXIS code is not enabled, use default
sysclk value as 100MHz per board documentation.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
This allows using PCIe NIC without enabling DPAA FMan.
Signed-off-by: York Sun <york.sun@nxp.com>
CC: Mingkai Hu <mingkai.hu@nxp.com>
Acked-by: Mingkai Hu <mingkai.hu@nxp.com>
LS2080ARDB/LS2088ARDB RevF board has smart voltage translator
which needs to be programmed to enable high speed SD interface
by setting GPIO4_10 output to zero.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In situations like an autobuilder we are likely to not have bl31.bin
present and thus would fail to build and propagate the error upwards.
Instead, print a big warning to stderr so that human will see that
something is wrong but complete the build.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
trini: Make Kconfig SPL_xxx entires only show if SPL, so that we don't
get Kconfig errors on platforms without SPL, ie sandbox (without SPL).
Signed-off-by: Tom Rini <trini@konsulko.com>
At present IDE support is controlled by CONFIG_CMD_IDE. Add a separate
CONFIG_IDE option so that IDE support can be enabled without requiring
the 'ide' command.
Update existing users and move the ide driver into drivers/block since
it should not be in common/.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HD44760
Also drop CONFIG_CMD_HD44780 which appears to be a typo.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_CMD_HASH
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework slightly, enable on some boards again]
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_ESBC_VALIDATE
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_CMD_EEPROM
CONFIG_CMD_EEPROM_LAYOUT
CONFIG_EEPROM_LAYOUT_HELP_STRING
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
[trini: Rework Kconfig logic slightly, define EEPROM location on TI eval
platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
This subsystem is quite old. It has been replaced with a driver-model
version (UCLASS_THERMAL). Boards are free to convert to that if required,
but here is a removal patch that could be applied in the meantime.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit 94e3c8c4fd ("crypto/fsl - Add progressive hashing support
using hardware acceleration.") created entries for CONFIG_SHA1,
CONFIG_SHA256, CONFIG_SHA_HW_ACCEL, and CONFIG_SHA_PROG_HW_ACCEL.
However, no defconfig has migrated to it. Complete the move by first
adding additional logic to various Kconfig files to select this when
required and then use the moveconfig tool. In many cases we can select
these because they are required to implement other drivers. We also
correct how we include the various hashing algorithms in SPL.
This commit was generated as follows (after Kconfig additions):
[1] tools/moveconfig.py -y SHA1 SHA256 SHA_HW_ACCEL
[2] tools/moveconfig.py -y SHA_PROG_HW_ACCEL
Note:
We cannot move SHA_HW_ACCEL and SHA_PROG_HW_ACCEL simultaneously
because there is dependency between them.
Cc: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: Naveen Burmi <NaveenBurmi@freescale.com>
Cc: Po Liu <po.liu@freescale.com>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Cc: Priyanka Jain <Priyanka.Jain@freescale.com>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Cc: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Chander Kashyap <k.chander@samsung.com>
Cc: Steve Rae <steve.rae@raedomain.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Feng Li <feng.li_2@nxp.com>
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: Mingkai Hu <Mingkai.Hu@freescale.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Akshay Saraswat <akshay.s@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts the following to Kconfig:
CONFIG_SPL_BOARD_INIT
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
[trini: Update the Kconfig logic]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add minor ifdeffery and default board config for the Salvator-XS board
with R8A7796 M3 SoC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Rename the salvator-x_defconfig to r8a7795_salvator-x_defconfig in
preparation for the r8a7796 support on salvator-x board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Instead of counting only the DRAM in the first slot, count
all the DRAM in all slots and report it accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the EHCI USB.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for rebooting the board using the ROHM BD9571MWV I2C PMIC,
but keep the CPU reboot option as a fallback.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the AVB ethernet on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for the SD card slots on the Salvator-X board.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The UART uses internal SCIF clock except on R8A7795 H3 WS1.0 .
Use the internal clock and ignore the early version of the chip.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The macro is used twice in the salvator-x board file, drop one.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reset ENET_RST_B to make ENET function stable.
Since DM_GPIO enabled, we use "gpio_spi@0_5" which corresponds
to ENET_RST_B.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Enable more DM drivers. The imx I2C/MMC DM drivers needs DM_GPIO
enabled. The 74x164 drivers needs SOFT_SPI and DM_GPIO enabled.
So needs to enable them together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Early backports of the imx wdog external reset feature occured before the
property was accepted upstream and used 'ext-reset-output' instead of
'fsl,ext-reset-output'. In order to support older kernels remove both
properties.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Now that mx6sabresd_spl_defconfig can be used to boot all
mx6sabresd variants, the non-SPL targets can be safely removed.
Signed-off-by: Fabio Estevam <fabio.estvam@nxp.com>
Add support for the mx6dlsabresd board in SPL.
Retrieved the DCD table from:
board/freescale/mx6sabresd/mx6dlsabresd.cfg
(NXP U-Boot branch imx_v2015.04_4.1.15_1.0.0_ga)
Flashed SPL and u-boot.img to an SD card and could successfully boot it
on mx6q, mx6qp and mx6dl sabresd boards.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently only MX6Q/QP sabresd boards are supported in SPL.
In order to also support MX6DL we need to convert to using
IOMUX_PADS and SETUP_IOMUX_PADS macros.
Other than that move the <asm/arch/mx6-ddr.h> header inclusion to the
SPL code block in order to avoid build error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Move board_late_init into common area from supported boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Move possible common board code into common area
from supported boards.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL code for geam6 and isiot are same, so
move them in common area.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL code for icorem6 and icorem6_rqs are same, so
move them in common area.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add generic SETUP_IOMUX_PADS function, for imx6ul mux pads
and use them in Is.IoT board.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
mmc2 in Is.IoT using usdhc1_pads instead usdhc2_pads,
so update the same.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Usually the drive strength values for DQ and SDL are 0x30 and
0x28 respectively, update them accordingly.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Since, u-boot handle fdt through uart so move the UART code
to SPL instead make it to global area.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL FIT is able to pick the suitable fdt file for u-boot,
so add that function through board_fit_config_name_match.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Let the runtime code can set the mmcdev and mmcroot based
on the devno using mmc_get_env_dev instead of defining
separately in build-time configs using mmc_late_init func.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add runtime, modeboot env which is setting mmcboot, or
nandboot based on the bootdevice so-that conditional
macros b/w MMC and NAND for CONFIG_BOOTCOMMAND should
be avoided in config files.
Cc: Matteo Lisi <matteo.lisi@engicam.com>
Cc: Michael Trimarchi <michael@amarulasolutions.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
After speaking to Hans at FOSDEM, he is fine with transferring the
maintainership of the Pine64 boards over to me.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
With the DRAM init code and the SPL's ability to load the ATF binary as
well, we can now officially get rid of the boot0 boot method, which
involed a closed-source proprietary blob to be used.
Rework the Pine64 README file to document how to build the firmware.
Also since these instructions now cover more boards, rename the
file to README.sunxi64 to reflect this.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that we can store a DT name in the SPL header, use this string (if
available) when finding the right DT blob to load for U-Boot proper.
This allows a generic U-Boot (proper) image to be combined with a bunch
of supported DTs, with just the SPL (possibly only that string) to be
different.
Eventually this string can be written after the build process by some
firmware update tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Now that the Makefile can call a generator script to build a more
advanced FIT image, let's use this feature to address the needs of
Allwinner boards with 64-bit SoCs (A64 and H5).
The (DTB stripped) U-Boot binary and the ATF are static, but we allow
an arbitrary number of supported device trees to be passed.
The script enters both a DT entry in the /images node and the respective
subnode in /configurations to support all listed DTBs.
The location of the bl31.bin image from the ARM Trusted Firmware build
can either by specified via the BL31 environment variable. If this is not
set, the script looks for bl31.bin in U-Boot's build directory (which
could be a symlink as well).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For a board or platform to support FIT loading in the SPL, it has to
provide a board_fit_config_name_match() routine, which helps to select
one of possibly multiple DTBs contained in a FIT image.
Provide a simple function which chooses the DT name U-Boot was
configured with.
If the DT name is one of the two Pine64 versions, determine the exact
model by checking the DRAM size.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
The sunxi SPL was holding the detected RAM size in some local variable
only, so it wasn't accessible for other functions.
Store the value in gd->ram_size instead, so it can be used later on.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
- Add #undef CONFIG_DM_MMC_OPS to omap3_logic in the SPL build case, to
match other TI platforms in the same situation.
Signed-off-by: Tom Rini <trini@konsulko.com>
Enable TI_COMMON_CMD_OPTIONS and remove similar options
from the defconfig. Updated with savedefconfig
CMD_USB isn't enabled yet. I have some testing to do with
musb.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
We make use of CONFIG_OMAP3_EVM today to know when to do a specific
tweak in MUSB. This can be tested on via CONFIG_TARGET_OMAP3_EVM
instead, so switch there so we can drop the now unused symbol
CONFIG_OMAP3_EVM. In investigating what to do about the symbol usage we
see that the cairo board defines the same function, but never called it
(as it does not define CONFIG_OMAP3_EVM) and was just returning anyhow,
so drop that function from that board.
Cc: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Now CONFIG_GENERIC_MMC and CONFIG_MMC match for all defconfig.
We do not need two options for the same feature. Deprecate the
former.
This commit was generated with the sed script 's/GENERIC_MMC/MMC/'
and manual fixup of drivers/mmc/Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Drop use of this long-deprecated option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This option is pretty old. It predates CONFIG_SYS_I2C which is itself
deprecated in favour of driver model. Disable it for all boards.
Also drop I2C options which depend on this.
Signed-off-by: Simon Glass <sjg@chromium.org>
OMAP-L138 LCDK board can benefit from using the commonly
used commands enabled by TI_COMMON_CMD_OPTIONS.
Source the relevant Kconfig file so TI_COMMON_CMD_OPTIONS
can be enabled for OMAP-L138 LCDK board in a future patch.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The function 'spin_wheel' is declared as inline, but not static and thus
we see warnings that 'w' and 'p' are declared static in a non-static
inline function. Correct this by marking spin_wheel as static inline.
Cc: TsiChung Liew <Tsi-Chung.Liew@freescale.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable vga_pads is never referenced, drop.
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
add a gaurd. The variable gpio_pads is never referenced, drop it. The
variable usdhc4_pads are only referenced when we do not have
CONFIG_CMD_NAND set and we are not doing an SPL build, modify the
existing guard.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The variables prg_stage2_prepare, prg_stage2_success and prg_stage_fail
are only referenced when CCDM_SECOND_STAGE is set, move these to be by
the existing guard.
Cc: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable nfc_pads is only referenced when CONFIG_CMD_NAND is set,
move the existing guard and drop a now redundant comment. The variable
gwproto_gpio_pads is never referenced, remove it.
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable usdhc1_pads is only referenced during SPL builds, add a guard.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The variable usdhc1_pads is only referenced during SPL builds, add a
guard.
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The variable usdhc2_pads is only referenced during SPL builds, add a guard.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Tom Rini <trini@konsulko.com>
The variable pwm_pad is never referenced, drop.
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
With gcc-6 and later we see a warning about the fact that we have a
construct of "if (test);\n\tstatement". Upon reviewing the code, the
intention here is as the compiler suggests, we only want to execute the
indented statement if the test was true.
Cc: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
am335x supports various sysclk frequencies which can be determined
using sysboot pins. PLLs should be configures based on this
sysclk frequency. Add PLL configurations for all supported
frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
