[ Upstream commit c8aebc1346522d3569690867ce3996642ad52e01 ]
This fixes the bindings in media framework:
The CSI40 is endpoint number 2
The CSI41 is endpoint number 3
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210312174735.2118212-1-niklas.soderlund+renesas@ragnatech.se
Fixes: 3182aa4e0b ("arm64: dts: renesas: r8a77980: add CSI2/VIN support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit de3abdf3d15c6e7f456e2de3f9da78f3a31414cc ]
The last cell of 'gpio-ranges' should be number of GPIO pins, and in
case of qcom platform it should match msm_pinctrl_soc_data.ngpio rather
than msm_pinctrl_soc_data.ngpio - 1.
This fixes the problem that when the last GPIO pin in the range is
configured with the following call sequence, it always fails with
-EPROBE_DEFER.
pinctrl_gpio_set_config()
pinctrl_get_device_gpio_range()
pinctrl_match_gpio_range()
Fixes: e13c6d144f ("arm64: dts: qcom: sm8150: Add base dts file")
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210303033106.549-3-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 388708028e6937f3fc5fc19aeeb847f8970f489c ]
The arm64 assembler in binutils 2.32 and above generates a program
property note in a note section, .note.gnu.property, to encode used x86
ISAs and features. But the kernel linker script only contains a single
NOTE segment:
PHDRS
{
text PT_LOAD FLAGS(5) FILEHDR PHDRS; /* PF_R|PF_X */
dynamic PT_DYNAMIC FLAGS(4); /* PF_R */
note PT_NOTE FLAGS(4); /* PF_R */
}
The NOTE segment generated by the vDSO linker script is aligned to 4 bytes.
But the .note.gnu.property section must be aligned to 8 bytes on arm64.
$ readelf -n vdso64.so
Displaying notes found in: .note
Owner Data size Description
Linux 0x00000004 Unknown note type: (0x00000000)
description data: 06 00 00 00
readelf: Warning: note with invalid namesz and/or descsz found at offset 0x20
readelf: Warning: type: 0x78, namesize: 0x00000100, descsize: 0x756e694c, alignment: 8
Since the note.gnu.property section in the vDSO is not checked by the
dynamic linker, discard the .note.gnu.property sections in the vDSO.
Similar to commit 4caffe6a28d31 ("x86/vdso: Discard .note.gnu.property
sections in vDSO"), but for arm64.
Signed-off-by: Bill Wendling <morbo@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210423205159.830854-1-morbo@google.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1d88358a89dbac9c7d4559548b9a44840456e6fb upstream.
Add "syscon" compatible to the North Bridge clocks node to allow the
cpufreq driver to access these registers via syscon API.
This is needed for a fix of cpufreq driver.
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: e8d66e7927 ("arm64: dts: marvell: armada-37xx: add nodes...")
Cc: stable@vger.kernel.org
Cc: Gregory CLEMENT <gregory.clement@free-electrons.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 4d09ccc4a81e7de6b002482af554d8b5626f5041 ]
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
This was based on the observation that the Pine64-LTS has as "push-push"
SD card socket, and that the schematic mentions the card detect GPIO.
After having received two reports about failing SD card access with that
patch, some more research and polls on that subject revealed that there
are at least two different versions of the Pine64-LTS out there:
- On some boards (including mine) the card detect pin is "stuck" at
high, regardless of an microSD card being inserted or not.
- On other boards the card-detect is working, but is active-high, by
virtue of an explicit inverter circuit, as shown in the schematic.
To cover all versions of the board out there, and don't take any chances,
let's revert the introduction of the active-low CD GPIO, but let's use
the broken-cd property for the Pine64-LTS this time. That should avoid
regressions and should work for everyone, even allowing SD card changes
now.
The SOPine card detect has proven to be working, so let's keep that
GPIO in place.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Michael Weiser <michael.weiser@gmx.de>
Reported-by: Daniel Kulesz <kuleszdl@posteo.org>
Suggested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Michael Weiser <michael.weiser@gmx.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210414104740.31497-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
Remove reserved memory for isp1 because now only use one isp0 for tuning tool.
The reserved memory is only used for tuning tool, could be removed for normal
operations.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: G.n. Zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 5f2220e87dd8a8fb86f524ea7945ab1d4155bc73)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
MIPI1 and LVDS1 should be enabled in the HDMI configuration.
Added DP configuration for MEK board.
Signed-off-by: Oliver Brown <oliver.brown@nxp.com>
(cherry picked from commit cfdd6c60d3bf1da3d5d4c71b6f4834dc503bcbc0)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Disable the L1SS feature in default.
Please remove this patch, if L1SS is required, and make sure
that the HW supports L1SS.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
(cherry picked from commit 2843e1e62c991aab16150a56508d415fd43f3fbc)
(cherry picked from commit 268df946aca1035818afbec42538e6bbb47378bf)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
(cherry picked from commit d9f9d0c73d3965e6a7b130e2b762a8ff7d4f04a7)
(cherry picked from commit 6430191c9f1e833284ce4cc5915d3fe26c38b024)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
This patch replaced link-frequencies to express single/dual cameras case, which
is introduced from 21c3114f6b280aef16b9298857ba2cd6f3e6d479
MLK-23600-6 Update Basler camera link-frequencies to differentiate used MIPI clock
Originally from Thies Moeller <thies.moeller@baslerweb.com>
With the fix for max-pixel-frequency for dual cameras basler camera + ov5640.
For other sensor porting, could also use max-pixel-frequency property.
Other properties might be optional.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: G.n. Zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 7f83103b6b7c40d13df781efe0763de3e14378fd)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Specify the clock rate and parent of i.MX8MQ/MM PCIe clocks.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
(cherry picked from commit 5c9865f4184ad9251d147126814a36e193226aae)
(cherry picked from commit 768c144fca6f3ba4285e80e09e4aec803ffea1a7)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The commit af20fa807f455ef846f7ffcebc6f489f285b1622 introduced a break when cherry-pick from mainline.
make[3]: *** No rule to make target 'arch/arm64/boot/dts/freescale/imx8mp-evk-iqaudio-dacplus.dtb', needed by '__build'. Stop.
make[3]: *** Waiting for unfinished jobs....
DTC arch/arm64/boot/dts/freescale/imx8mp-evk-dual-basler.dtb
make[2]: *** [../scripts/Makefile.build:500: arch/arm64/boot/dts/freescale] Error 2
make[1]: *** [/home/nxa14866/ProjectA/linux-imx_bk/Makefile:1269: dtbs] Error 2
make[1]: Leaving directory '/home/nxa14866/ProjectA/linux-imx_bk/build_v8'
make: *** [Makefile:179: sub-make] Error 2
The patch removed build for imx8mp-evk-iqaudio-dacplus.dtb because it's not in this branch.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
(cherry picked from commit aa26d4f35de3b5a4d27d597e837280b6148e32ee)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
for 1 ISP camera on CSI0, MIPI CSI clock set to 500MHz
for 2 ISP cameras on CSI0/CSI1, MIPI CSI clock both set to 266MHz
Basler camera driver uses link-frequencies to retrieve proper clocks on
1 ISP or 2 ISP cameras cases.
Originally from Thies Moeller <thies.moeller@baslerweb.com>
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit bb98a98727e49cc40539be66c5f7aefc8e6009b9)
(cherry picked from commit 21c3114f6b280aef16b9298857ba2cd6f3e6d479)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
use memory-region to get reserved memory
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 5a28380ef4f4afffdabcfacd062706487cc150f8)
(cherry picked from commit 9a75296315d40f8737bda9d5d097a0c6d402ff16)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Previously it controls dewarp in mipi driver which is not standard way.
Now use gpr to control dewarp in dewarp driver.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 22373bd4b6979bc9c8e63b678bcd5204714fd4c9)
(cherry picked from commit 7db1a365173f9a94a402192bb13b0fe80bc4175c)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
second virtual dewarp node not needed as VSI gets back to use the real dewarp
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit bf7698bb60035c7b32cec6f7c57e3072869a7888)
(cherry picked from commit 420d04d11c0c4b37ec6913ddead75dcf14482d9d)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
update ISP and Dewarp clock and power
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit e6031680ba2d67a6961a5da5fc68a913962c66d2)
(cherry picked from commit f5390f2bcbc7cb9fab29605fc2d3cb61373a5800)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Set MIPI clock according to IC team.
for 1 ISP camera on CSI0, MIPI CSI clock set to 500MHz
for 2 ISP cameras on CSI0/CSI1, MIPI CSI clock both set to 266MHz
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit a38f457b63fa8a0d9b4c5de39a12959c172e7e35)
(cherry picked from commit e20ebbce9f06086249d7dda9d73bd9e328074c02)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
add dual baslers camera support to work with dual ISPs
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit a755ce242b551dafcca648f9d54585fd9ba02493)
(cherry picked from commit b8ac5f33cdaa0d957e6ffb5096809a830452fffb)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
add dual isp supports with basler camera and ov2775
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 2bd39f91a47ad50981f96dd46b1f9e50a0cc0266)
(cherry picked from commit af20fa807f455ef846f7ffcebc6f489f285b1622)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
enable the virtual dewarp to work with ISP SW release P8.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 0fff98516a430952b97102053c438d1ab27c97a1)
(cherry picked from commit 15b0588e6cda16de34dbcad401bd89216794a527)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
on iMX8MP, there's only 1 dewarp.
the patch adds a second dewarp node (virtual) to work with ISP SW release P8.
this might be removed after vendor modify the way using dewarp.
Signed-off-by: Robby Cai <robby.cai@nxp.com>
Reviewed-by: Guoniu.zhou <guoniu.zhou@nxp.com>
(cherry picked from commit 3c32b1080083faff8381cdeb1adadaff0144aac3)
(cherry picked from commit b16c09a8bd51a74a988f6d05734bfbf776bee9a2)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Set the parent clock for PCIE_AUX clock firstly, then set the rate of
the PCI_AUX clock to 10MHZ.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
(cherry picked from commit c787efe575330e538cc92da0dde49255bdc80c94)
(cherry picked from commit 855ad0c9b3e9ea03f34c70332a2175cd604acf6c)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Set the PCIe CLKREQ# as input and add the num-viewport property for
i.MX8MP PCIe RC port.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
(cherry picked from commit f95d91816f5d521b2dec5fa2fe7f2a52a381eded)
(cherry picked from commit 8a5e146adec7c948bfaa250f5c54f9d6fb2de471)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
fix the clkreq# is always low issue when L1.1 ASPM is enabled.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jun Li <jun.li@nxp.com>
(cherry picked from commit 6c3f41636a97d020aad4d4ebb43c6b9f6f9ddcb4)
(cherry picked from commit a661f2f5e85159ae69c2819fda04f2817856b0e0)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
In the i.MX8MP PCIe design, the PCIe PHY REF clock comes from external
OSC or internal system PLL. It is configured in the IOMUX_GPR14 register
directly, and can't be contolled by CCM at all.
So, correct it in the DTS node.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
(cherry picked from commit 65b5b8974b14cc4fee501310e97e675eda4f4e1b)
(cherry picked from commit db6a520392f7dfd6219aa12d78748030d4809e92)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
I2c chip are reset when the partition reboots.
A partition reboot has to reset the ones used by a specific OS.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
(cherry picked from commit 3362e480195360303b60b17d0c563f0c837c6f58)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
[ Upstream commit 3dd4ce4185df6798dcdcc3669bddb35899d7d5e1 ]
Commit 941432d00768 ("arm64: dts: allwinner: Drop non-removable from
SoPine/LTS SD card") enabled the card detect GPIO for the SOPine module,
along the way with the Pine64-LTS, which share the same base .dtsi.
However while both boards indeed have a working CD GPIO on PF6, the
polarity is different: the SOPine modules uses a "push-pull" socket,
which has an active-high switch, while the Pine64-LTS use the more
traditional push-push socket and the common active-low switch.
Fix the polarity in the sopine.dtsi, and overwrite it in the LTS
board .dts, to make the SD card work again on systems using SOPine
modules.
Fixes: 941432d00768 ("arm64: dts: allwinner: Drop non-removable from SoPine/LTS SD card")
Reported-by: Ashley <contact@victorianfox.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210316144219.5973-1-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 22315a2296f4c251fa92aec45fbbae37e9301b6c upstream.
After commit 2decad92f473 ("arm64: mte: Ensure TIF_MTE_ASYNC_FAULT is
set atomically"), LLVM's integrated assembler fails to build entry.S:
<instantiation>:5:7: error: expected assembly-time absolute expression
.org . - (664b-663b) + (662b-661b)
^
<instantiation>:6:7: error: expected assembly-time absolute expression
.org . - (662b-661b) + (664b-663b)
^
The root cause is LLVM's assembler has a one-pass design, meaning it
cannot figure out these instruction lengths when the .org directive is
outside of the subsection that they are in, which was changed by the
.arch_extension directive added in the above commit.
Apply the same fix from commit 966a0acce2fc ("arm64/alternatives: move
length validation inside the subsection") to the alternative_endif
macro, shuffling the .org directives so that the length validation
happen will always happen in the same subsections. alternative_insn has
not shown any issue yet but it appears that it could have the same issue
in the future so just preemptively change it.
Fixes: f7b93d42945c ("arm64/alternatives: use subsections for replacement sequences")
Cc: <stable@vger.kernel.org> # 5.8.x
Link: https://github.com/ClangBuiltLinux/linux/issues/1347
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Tested-by: Sami Tolvanen <samitolvanen@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Tested-by: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/r/20210414000803.662534-1-nathan@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit a354a64d91eec3e0f8ef0eed575b480fd75b999c ]
Disable guest access to the Trace Filter control registers.
We do not advertise the Trace filter feature to the guest
(ID_AA64DFR0_EL1: TRACE_FILT is cleared) already, but the guest
can still access the TRFCR_EL1 unless we trap it.
This will also make sure that the guest cannot fiddle with
the filtering controls set by a nvhe host.
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-3-suzuki.poulose@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1d676673d665fd2162e7e466dcfbe5373bfdb73e ]
Currently we advertise the ID_AA6DFR0_EL1.TRACEVER for the guest,
when the trace register accesses are trapped (CPTR_EL2.TTA == 1).
So, the guest will get an undefined instruction, if trusts the
ID registers and access one of the trace registers.
Lets be nice to the guest and hide the feature to avoid
unexpected behavior.
Even though this can be done at KVM sysreg emulation layer,
we do this by removing the TRACEVER from the sanitised feature
register field. This is fine as long as the ETM drivers
can handle the individual trace units separately, even
when there are differences among the CPUs.
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210323120647.454211-2-suzuki.poulose@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 5cfad4f45806f6f898b63b8c77cea7452c704cb3 ]
Fix address of the pad control register
(IOMUXC_SW_PAD_CTL_PAD_SD1_DATA0) for SD1_DATA0_GPIO2_IO2. This seems
to be a typo but it leads to an exception when pinctrl is applied due to
wrong memory address access.
Signed-off-by: Oliver Stäbler <oliver.staebler@bytesatwork.ch>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Fixes: c1c9d41319 ("dt-bindings: imx: Add pinctrl binding doc for imx8mm")
Fixes: 748f908cc8 ("arm64: add basic DTS for i.MX8MQ")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 141f8202cfa4192c3af79b6cbd68e7760bb01b5a ]
The ppos points to a position in the old kernel memory (and in case of
arm64 in the crash kernel since elfcorehdr is passed as a segment). The
function should update the ppos by the amount that was read. This bug is
not exposed by accident, but other platforms update this value properly.
So, fix it in ARM64 version of elfcorehdr_read() as well.
Signed-off-by: Pavel Tatashin <pasha.tatashin@soleen.com>
Fixes: e62aaeac42 ("arm64: kdump: provide /proc/vmcore file")
Reviewed-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Link: https://lore.kernel.org/r/20210319205054.743368-1-pasha.tatashin@soleen.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 4fb3a074755b7737c4081cffe0ccfa08c2f2d29d upstream.
Crypto engine (CAAM) on LS1043A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.8+
Fixes: 63dac35b58 ("arm64: dts: ls1043a: add crypto node")
Link: https://lore.kernel.org/linux-crypto/fe6faa24-d8f7-d18f-adfa-44fa0caa1598@arm.com
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit ba8da03fa7dff59d9400250aebd38f94cde3cb0f upstream.
Crypto engine (CAAM) on LS1012A platform is configured HW-coherent,
mark accordingly the DT node.
Lack of "dma-coherent" property for an IP that is configured HW-coherent
can lead to problems, similar to what has been reported for LS1046A.
Cc: <stable@vger.kernel.org> # v4.12+
Fixes: 85b85c5695 ("arm64: dts: ls1012a: add crypto node")
Signed-off-by: Horia Geantă <horia.geanta@nxp.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit b96b0c5de685df82019e16826a282d53d86d112c upstream
The nVHE KVM hyp drains and disables the SPE buffer, before
entering the guest, as the EL1&0 translation regime
is going to be loaded with that of the guest.
But this operation is performed way too late, because :
- The owning translation regime of the SPE buffer
is transferred to EL2. (MDCR_EL2_E2PB == 0)
- The guest Stage1 is loaded.
Thus the flush could use the host EL1 virtual address,
but use the EL2 translations instead of host EL1, for writing
out any cached data.
Fix this by moving the SPE buffer handling early enough.
The restore path is doing the right thing.
Cc: stable@vger.kernel.org # v5.4-
Cc: Christoffer Dall <christoffer.dall@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Will Deacon <will@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
Commit 7d717558dd5ef10d28866750d5c24ff892ea3778 upstream.
KVM/arm64 has forever used a 40bit default IPA space, partially
due to its 32bit heritage (where the only choice is 40bit).
However, there are implementations in the wild that have a *cough*
much smaller *cough* IPA space, which leads to a misprogramming of
VTCR_EL2, and a guest that is stuck on its first memory access
if userspace dares to ask for the default IPA setting (which most
VMMs do).
Instead, blundly reject the creation of such VM, as we can't
satisfy the requirements from userspace (with a one-off warning).
Also clarify the boot warning, and document that the VM creation
will fail when an unsupported IPA size is provided.
Although this is an ABI change, it doesn't really change much
for userspace:
- the guest couldn't run before this change, but no error was
returned. At least userspace knows what is happening.
- a memory slot that was accepted because it did fit the default
IPA space now doesn't even get a chance to be registered.
The other thing that is left doing is to convince userspace to
actually use the IPA space setting instead of relying on the
antiquated default.
Fixes: 233a7cb235 ("kvm: arm64: Allow tuning the physical address size for VM")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Cc: stable@vger.kernel.org
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Link: https://lore.kernel.org/r/20210311100016.3830038-2-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 01dc9262ff5797b675c32c0c6bc682777d23de05 upstream.
It recently became apparent that the ARMv8 architecture has interesting
rules regarding attributes being used when fetching instructions
if the MMU is off at Stage-1.
In this situation, the CPU is allowed to fetch from the PoC and
allocate into the I-cache (unless the memory is mapped with
the XN attribute at Stage-2).
If we transpose this to vcpus sharing a single physical CPU,
it is possible for a vcpu running with its MMU off to influence
another vcpu running with its MMU on, as the latter is expected to
fetch from the PoU (and self-patching code doesn't flush below that
level).
In order to solve this, reuse the vcpu-private TLB invalidation
code to apply the same policy to the I-cache, nuking it every time
the vcpu runs on a physical CPU that ran another vcpu of the same
VM in the past.
This involve renaming __kvm_tlb_flush_local_vmid() to
__kvm_flush_cpu_context(), and inserting a local i-cache invalidation
there.
Cc: stable@vger.kernel.org
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210303164505.68492-1-maz@kernel.org
[maz: added 32bit ARM support]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 7ba8f2b2d652cd8d8a2ab61f4be66973e70f9f88 ]
52-bit VA kernels can run on hardware that is only 48-bit capable, but
configure the ID map as 52-bit by default. This was not a problem until
recently, because the special T0SZ value for a 52-bit VA space was never
programmed into the TCR register anwyay, and because a 52-bit ID map
happens to use the same number of translation levels as a 48-bit one.
This behavior was changed by commit 1401bef703a4 ("arm64: mm: Always update
TCR_EL1 from __cpu_set_tcr_t0sz()"), which causes the unsupported T0SZ
value for a 52-bit VA to be programmed into TCR_EL1. While some hardware
simply ignores this, Mark reports that Amberwing systems choke on this,
resulting in a broken boot. But even before that commit, the unsupported
idmap_t0sz value was exposed to KVM and used to program TCR_EL2 incorrectly
as well.
Given that we already have to deal with address spaces being either 48-bit
or 52-bit in size, the cleanest approach seems to be to simply default to
a 48-bit VA ID map, and only switch to a 52-bit one if the placement of the
kernel in DRAM requires it. This is guaranteed not to happen unless the
system is actually 52-bit VA capable.
Fixes: 90ec95cda9 ("arm64: mm: Introduce VA_BITS_MIN")
Reported-by: Mark Salter <msalter@redhat.com>
Link: http://lore.kernel.org/r/20210310003216.410037-1-msalter@redhat.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210310171515.416643-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit eeb0753ba27b26f609e61f9950b14f1b934fe429 ]
pfn_valid() validates a pfn but basically it checks for a valid struct page
backing for that pfn. It should always return positive for memory ranges
backed with struct page mapping. But currently pfn_valid() fails for all
ZONE_DEVICE based memory types even though they have struct page mapping.
pfn_valid() asserts that there is a memblock entry for a given pfn without
MEMBLOCK_NOMAP flag being set. The problem with ZONE_DEVICE based memory is
that they do not have memblock entries. Hence memblock_is_map_memory() will
invariably fail via memblock_search() for a ZONE_DEVICE based address. This
eventually fails pfn_valid() which is wrong. memblock_is_map_memory() needs
to be skipped for such memory ranges. As ZONE_DEVICE memory gets hotplugged
into the system via memremap_pages() called from a driver, their respective
memory sections will not have SECTION_IS_EARLY set.
Normal hotplug memory will never have MEMBLOCK_NOMAP set in their memblock
regions. Because the flag MEMBLOCK_NOMAP was specifically designed and set
for firmware reserved memory regions. memblock_is_map_memory() can just be
skipped as its always going to be positive and that will be an optimization
for the normal hotplug memory. Like ZONE_DEVICE based memory, all normal
hotplugged memory too will not have SECTION_IS_EARLY set for their sections
Skipping memblock_is_map_memory() for all non early memory sections would
fix pfn_valid() problem for ZONE_DEVICE based memory and also improve its
performance for normal hotplug memory as well.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Acked-by: David Hildenbrand <david@redhat.com>
Fixes: 73b20c84d4 ("arm64: mm: implement pte_devmap support")
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/1614921898-4099-2-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 86c83365ab76e4b43cedd3ce07a07d32a4dc79ba upstream.
When CONFIG_DEBUG_VIRTUAL is enabled, the default page_to_virt() macro
implementation from include/linux/mm.h is used. That definition doesn't
account for KASAN tags, which leads to no tags on page_alloc allocations.
Provide an arm64-specific definition for page_to_virt() when
CONFIG_DEBUG_VIRTUAL is enabled that takes care of KASAN tags.
Fixes: 2813b9c029 ("kasan, mm, arm64: tag non slab memory allocated via pagealloc")
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrey Konovalov <andreyknvl@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/4b55b35202706223d3118230701c6a59749d9b72.1615219501.git.andreyknvl@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit df84fe94708985cdfb78a83148322bcd0a699472 upstream.
Since commit f086f67485 ("arm64: ptrace: add support for syscall
emulation"), if system call number -1 is called and the process is being
traced with PTRACE_SYSCALL, for example by strace, the seccomp check is
skipped and -ENOSYS is returned unconditionally (unless altered by the
tracer) rather than carrying out action specified in the seccomp filter.
The consequence of this is that it is not possible to reliably strace
a seccomp based implementation of a foreign system call interface in
which r7/x8 is permitted to be -1 on entry to a system call.
Also trace_sys_enter and audit_syscall_entry are skipped if a system
call is skipped.
Fix by removing the in_syscall(regs) check restoring the previous
behaviour which is like AArch32, x86 (which uses generic code) and
everything else.
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Catalin Marinas<catalin.marinas@arm.com>
Cc: <stable@vger.kernel.org>
Fixes: f086f67485 ("arm64: ptrace: add support for syscall emulation")
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Timothy E Baldwin <T.E.Baldwin99@members.leeds.ac.uk>
Link: https://lore.kernel.org/r/90edd33b-6353-1228-791f-0336d94d5f8c@majoroak.me.uk
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit f5c6d0fcf90ce07ee0d686d465b19b247ebd5ed7 upstream.
These plt* and .text.ftrace_trampoline sections specified for arm64 have
non-zero addressses. Non-zero section addresses in a relocatable ELF would
confuse GDB when it tries to compute the section offsets and it ends up
printing wrong symbol addresses. Therefore, set them to zero, which mirrors
the change in commit 5d8591bc0f ("module: set ksymtab/kcrctab* section
addresses to 0x0").
Reported-by: Frank van der Linden <fllinden@amazon.com>
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210216183234.GA23876@amazon.com
Signed-off-by: Will Deacon <will@kernel.org>
[shaoyi@amazon.com: made same changes in arch/arm64/kernel/module.lds for 5.4]
Signed-off-by: Shaoying Xu <shaoyi@amazon.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c0b15c25d25171db4b70cc0b7dbc1130ee94017d upstream.
The erratum 1024718 affects Cortex-A55 r0p0 to r2p0. However
we apply the work around for r0p0 - r1p0. Unfortunately this
won't be fixed for the future revisions for the CPU. Thus
extend the work around for all versions of A55, to cover
for r2p0 and any future revisions.
Cc: stable@vger.kernel.org
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20210203230057.3961239-1-suzuki.poulose@arm.com
[will: Update Kconfig help text]
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit d47422d953e258ad587b5edf2274eb95d08bdc7d upstream.
As stated in linux/errno.h, ENOTSUPP should never be seen by user programs.
When we set up uprobe with 32-bit perf and arm64 kernel, we would see the
following vague error without useful hint.
The sys_perf_event_open() syscall returned with 524 (INTERNAL ERROR:
strerror_r(524, [buf], 128)=22)
Use EOPNOTSUPP instead to indicate such cases.
Signed-off-by: He Zhe <zhe.he@windriver.com>
Link: https://lore.kernel.org/r/20210223082535.48730-1-zhe.he@windriver.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 656d1d58d8e0958d372db86c24f0b2ea36f50888 upstream.
in function create_dtb(), if fdt_open_into() fails, we need to vfree
buf before return.
Fixes: 52b2a8af74 ("arm64: kexec_file: load initrd and device-tree")
Cc: stable@vger.kernel.org # v5.0
Signed-off-by: qiuguorui1 <qiuguorui1@huawei.com>
Link: https://lore.kernel.org/r/20210218125900.6810-1-qiuguorui1@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 0df07d8117c3576f1603b05b84089742a118d10a upstream.
The accelerated, instruction based implementations of SHA1, SHA2 and
SHA3 are autoloaded based on CPU capabilities, given that the code is
modest in size, and widely used, which means that resolving the algo
name, loading all compatible modules and picking the one with the
highest priority is taken to be suboptimal.
However, if these algorithms are requested before this CPU feature
based matching and autoloading occurs, these modules are not even
considered, and we end up with suboptimal performance.
So add the missing module aliases for the various SHA implementations.
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 9d41053e8dc115c92b8002c3db5f545d7602498b ]
Although there has been a bit of back and forth on the subject, it
appears that invalidating TLBs requires an ISB instruction when FEAT_ETS
is not implemented by the CPU.
From the bible:
| In an implementation that does not implement FEAT_ETS, a TLB
| maintenance instruction executed by a PE, PEx, can complete at any
| time after it is issued, but is only guaranteed to be finished for a
| PE, PEx, after the execution of DSB by the PEx followed by a Context
| synchronization event
Add the missing ISB in __primary_switch, just in case.
Fixes: 3c5e9f238b ("arm64: head.S: move KASLR processing out of __enable_mmu()")
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210224093738.3629662-3-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 15deb4333cd6d4e1e3216582e4c531ec40a6b060 ]
Commit 69b6f2e817 ("crypto: arm64/aes-neon - limit exposed routines if
faster driver is enabled") intended to hide modes from the plain NEON
driver that are also implemented by the faster bit sliced NEON one if
both are enabled. However, the defined() CPP function does not detect
if the bit sliced NEON driver is enabled as a module. So instead, let's
use IS_ENABLED() here.
Fixes: 69b6f2e817 ("crypto: arm64/aes-neon - limit exposed routines if ...")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9d9bfcadfb43b856dbcf9419de75f7420d5a225 ]
The partition called "u-boot" in reality contains TF-A and U-Boot, and
TF-A is before U-Boot.
Rename this parition to "a53-firmware" to avoid confusion for users,
since they cannot simply build U-Boot from U-Boot repository and flash
the resulting image there. Instead they have to build the firmware with
the sources from the mox-boot-builder repository [1] and flash the
a53-firmware.bin binary there.
[1] https://gitlab.nic.cz/turris/mox-boot-builder
Signed-off-by: Marek Behún <kabel@kernel.org>
Fixes: 7109d817db ("arm64: dts: marvell: add DTS for Turris Mox")
Cc: Gregory CLEMENT <gregory.clement@bootlin.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 948c657cc45e8ce48cb533d4e2106145fa765759 ]
In contrast to the H6 (and later) manuals, the A64 datasheet does not
specify any limitations in the maximum possible frequency for eMMC
controllers.
However experimentation has found that a 150 MHz limit similar to other
SoCs and also the MMC0 and MMC1 controllers on the A64 seems to exist
for the MMC2 controller.
Limit the frequency for the MMC2 controller to 150 MHz in the SoC .dtsi.
The Pinebook seems to be the an odd exception, since it apparently seems
to work with 200 MHz as well, so overwrite this in its board .dts file.
Tested on a Pine64-LTS: 200 MHz HS-200 fails, 150 MHz HS-200 works.
Fixes: 22be992fae ("arm64: allwinner: a64: Increase the MMC max frequency")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-7-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cfe6c487b9a1abc6197714ec5605716a5428cf03 ]
The H6 manual explicitly lists a frequency limit of 150 MHz for the bus
frequency of the MMC controllers. So far we had no explicit limits in the
DT, which limited eMMC to the spec defined frequencies, or whatever the
driver defines (both Linux and FreeBSD use 52 MHz here).
Put those maximum frequencies in the SoC .dtsi, to allow higher speed
modes (which still would need to be explicitly enabled, per board).
Tested with an eMMC using HS-200 on a Pine H64. Running at the spec'ed
200 MHz indeed fails with I/O errors, but 150 MHz seems to work stably.
Fixes: 8f54bd1595 ("arm64: allwinner: h6: add device tree nodes for MMC controllers")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-6-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 941432d007689f3774646e41a1439228b6c6ee0e ]
The SD card on the SoPine SoM module is somewhat concealed, so was
originally defined as "non-removable".
However there is a working card-detect pin (tested on two different
SoM versions), and in certain SoM base boards it might be actually
accessible at runtime.
Also the Pine64-LTS shares the SoPine base .dtsi, so inherited the
non-removable flag, even though the SD card slot is perfectly accessible
and usable there. (It turns out that just *my* board has a broken card
detect switch, so I originally thought CD wouldn't work on the LTS.)
Drop the "non-removable" flag to describe the SD card slot properly.
Fixes: c3904a2698 ("arm64: allwinner: a64: add DTSI file for SoPine SoM")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-5-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit da2fb8457f71138d455cba82edec0d34f858e506 ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the H6 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: eabb3d424b ("arm64: dts: allwinner: h6: add USB2-related device nodes")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-3-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit cc72570747e43335f4933a24dd74d5653639176a ]
In recent Allwinner SoCs the first USB host controller (HCI0) shares
the first PHY with the MUSB controller. Probably to make this sharing
work, we were avoiding to declare this in the DT. This has two
shortcomings:
- U-Boot (which uses the same .dts) cannot use this port in host mode
without a PHY linked, so we were loosing one USB port there.
- It requires the MUSB driver to be enabled and loaded, although we
don't actually use it.
To avoid those issues, let's add this PHY link to the A64 .dtsi file.
After all PHY port 0 *is* connected to HCI0, so we should describe
it as this. Remove the part from the Pinebook DTS which already had
this property.
This makes it work in U-Boot, also improves compatiblity when no MUSB
driver is loaded (for instance in distribution installers).
Fixes: dc03a047df ("arm64: allwinner: a64: add EHCI0/OHCI0 nodes to A64 DTSI")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210113152630.28810-2-andre.przywara@arm.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 1fea2eb2f5bbd3fbbe2513d2386b5f6e6db17fd7 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 9589f7721e ("arm64: dts: Add S2MPS15 PMIC node on exynos7-espresso")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201210212903.216728-8-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit e98e2367dfb4b6d7a80c8ce795c644124eff5f36 ]
The Samsung PMIC datasheets describe the interrupt line as active low
with a requirement of acknowledge from the CPU. Without specifying the
interrupt type in Devicetree, kernel might apply some fixed
configuration, not necessarily working for this hardware.
Fixes: 01e5d23521 ("arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20201210212903.216728-7-krzk@kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 1e0ca5467445bc1f41a9e403d6161a22f313dae7 upstream.
HDA initialization is failing occasionally on Tegra210 and following
print is observed in the boot log. Because of this probe() fails and
no sound card is registered.
[16.800802] tegra-hda 70030000.hda: no codecs found!
Codecs request a state change and enumeration by the controller. In
failure cases this does not seem to happen as STATETS register reads 0.
The problem seems to be related to the HDA codec dependency on SOR
power domain. If it is gated during HDA probe then the failure is
observed. Building Tegra HDA driver into kernel image avoids this
failure but does not completely address the dependency part. Fix this
problem by adding 'power-domains' DT property for Tegra210 HDA. Note
that Tegra186 and Tegra194 HDA do this already.
Fixes: 742af7e7a0 ("arm64: tegra: Add Tegra210 support")
Depends-on: 96d1f078ff ("arm64: tegra: Add SOR power-domain for Tegra210")
Cc: <stable@vger.kernel.org>
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 93f2a11580a9732c1d90f9e01a7e9facc825658f ]
The GCC_LPASS_Q6_AXI_CLK and GCC_LPASS_SWAY_CLK clocks may not be
touched on a typical UEFI based SDM845 device, but when the kernel is
built with CONFIG_SDM_LPASSCC_845 this happens, unless they are marked
as protected-clocks in the DT.
This was done for the MTP and the Pocophone, but not for DB845c and the
Lenovo Yoga C630 - causing these to fail to boot if the LPASS clock
controller is enabled (which it typically isn't).
Tested-by: Vinod Koul <vkoul@kernel.org> #on db845c
Reviewed-by: Vinod Koul <vkoul@kernel.org>
Link: https://lore.kernel.org/r/20201222001103.3112306-1-bjorn.andersson@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 43f20b1c6140896916f4e91aacc166830a7ba849 ]
It recently became apparent that the lack of a 'device_type = "pci"'
in the PCIe root complex node for rk3399 is a violation of the PCI
binding, as documented in IEEE Std 1275-1994. Changes to the kernel's
parsing of the DT made such violation fatal, as drivers cannot
probe the controller anymore.
Add the missing property makes the PCIe node compliant. While we
are at it, drop the pointless linux,pci-domain property, which only
makes sense when there are multiple host bridges.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20200815125112.462652-3-maz@kernel.org
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit aa880c6f3ee6dbd0d5ab02026a514ff8ea0a3328 ]
Dcfg was overlapping with clockgen address space which resulted
in failure in memory allocation for dcfg. According regs description
dcfg size should not be bigger than 4KB.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Fixes: 8126d88162 ("arm64: dts: add QorIQ LS1046A SoC support")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit 7386a559caa6414e74578172c2bc4e636d6bd0a0 ]
In accordance with the DWC USB3 bindings the property is supposed to have
uint32 type. It's erroneous from the DT schema and driver points of view
to declare it as boolean. As Neil suggested set it to 0x20 so not break
the platform and to make the dtbs checker happy.
Link: https://lore.kernel.org/linux-usb/20201010224121.12672-16-Sergey.Semin@baikalelectronics.ru/
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Fixes: 9baf7d6be7 ("arm64: dts: meson: g12a: Add G12A USB nodes")
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201210091756.18057-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Sasha Levin <sashal@kernel.org>
[ Upstream commit a9164910c5ceed63551280a4a0b85d37ac2b19a5 ]
Indicated by AML code in ACPI table, the touchpad in-use could be found
on two possible slave addresses on &i2c3, i.e. hid@15 and hid@2c. And
which one is in-use can be determined by reading another address on the
I2C bus. Unfortunately, for DT boot, there is currently no support in
firmware to make this check and patch DT accordingly. This results in
a non-functional touchpad on those C630 devices with hid@2c.
As i2c-hid driver will stop probing the device if there is nothing on
the slave address, we can actually keep both devices enabled in DT, and
i2c-hid driver will only probe the existing one. The only problem is
that we cannot set up pinctrl in both device nodes, as two devices with
the same pinctrl will cause pin conflict that makes the second device
fail to probe. Let's move the pinctrl state up to parent node to solve
this problem. As the pinctrl state of parent node is already defined in
sdm845.dtsi, it ends up with overwriting pinctrl-0 with i2c3_hid_active
state added in there.
Fixes: 11d0e4f28156 ("arm64: dts: qcom: c630: Polish i2c-hid devices")
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20210102045940.26874-1-shawn.guo@linaro.org
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 91cb2c8b072e00632adf463b78b44f123d46a0fa upstream.
Commit 519ea6f1c82f ("arm64: Fix kernel address detection of
__is_lm_address()") fixed the incorrect validation of addresses below
PAGE_OFFSET. However, it no longer allowed tagged addresses to be passed
to virt_addr_valid().
Fix this by explicitly resetting the pointer tag prior to invoking
__is_lm_address(). This is consistent with the __lm_to_phys() macro.
Fixes: 519ea6f1c82f ("arm64: Fix kernel address detection of __is_lm_address()")
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Cc: <stable@vger.kernel.org> # 5.4.x
Cc: Will Deacon <will@kernel.org>
Cc: Vincenzo Frascino <vincenzo.frascino@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210201190634.22942-2-catalin.marinas@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 519ea6f1c82fcdc9842908155ae379de47818778 upstream.
Currently, the __is_lm_address() check just masks out the top 12 bits
of the address, but if they are 0, it still yields a true result.
This has as a side effect that virt_addr_valid() returns true even for
invalid virtual addresses (e.g. 0x0).
Fix the detection checking that it's actually a kernel address starting
at PAGE_OFFSET.
Fixes: 68dd8ef321 ("arm64: memory: Fix virt_addr_valid() using __is_lm_address()")
Cc: <stable@vger.kernel.org> # 5.4.x
Cc: Will Deacon <will@kernel.org>
Suggested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Link: https://lore.kernel.org/r/20210126134056.45747-1-vincenzo.frascino@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit 1653e3d470629d25c64cd8a2f84adb20a9348b0c ]
The offset of the reset request register is 0, the absolute address is
0x1e60000. Boards without PSCI support will fail to perform a reset:
[ 26.734700] reboot: Restarting system
[ 27.743259] Unable to restart system
[ 27.746845] Reboot failed -- System halted
Fixes: 8897f3255c ("arm64: dts: Add support for NXP LS1028A SoC")
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 7bc1a0f9e1765830e945669c99c59c35cf9bca82 upstream.
On arm64, the global variable memstart_addr represents the physical
address of PAGE_OFFSET, and so physical to virtual translations or
vice versa used to come down to simple additions or subtractions
involving the values of PAGE_OFFSET and memstart_addr.
When support for 52-bit virtual addressing was introduced, we had to
deal with PAGE_OFFSET potentially being outside of the region that
can be covered by the virtual range (as the 52-bit VA capable build
needs to be able to run on systems that are only 48-bit VA capable),
and for this reason, another translation was introduced, and recorded
in the global variable physvirt_offset.
However, if we go back to the original definition of memstart_addr,
i.e., the physical address of PAGE_OFFSET, it turns out that there is
no need for two separate translations: instead, we can simply subtract
the size of the unaddressable VA space from memstart_addr to make the
available physical memory appear in the 48-bit addressable VA region.
This simplifies things, but also fixes a bug on KASLR builds, which
may update memstart_addr later on in arm64_memblock_init(), but fails
to update vmemmap and physvirt_offset accordingly.
Fixes: 5383cc6efe ("arm64: mm: Introduce vabits_actual")
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Steve Capper <steve.capper@arm.com>
Link: https://lore.kernel.org/r/20201008153602.9467-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[ Upstream commit c35a824c31834d947fb99b0c608c1b9f922b4ba0 ]
With UBSAN enabled and building with clang, there are occasionally
warnings like
WARNING: modpost: vmlinux.o(.text+0xc533ec): Section mismatch in reference from the function arch_atomic64_or() to the variable .init.data:numa_nodes_parsed
The function arch_atomic64_or() references
the variable __initdata numa_nodes_parsed.
This is often because arch_atomic64_or lacks a __initdata
annotation or the annotation of numa_nodes_parsed is wrong.
for functions that end up not being inlined as intended but operating
on __initdata variables. Mark these as __always_inline, along with
the corresponding asm-generic wrappers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210108092024.4034860-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
commit 2a5f1b67ec577fb1544b563086e0377f095f88e2 upstream.
We reset the guest's view of PMCR_EL0 unconditionally, based on
the host's view of this register. It is however legal for an
implementation not to provide any PMU, resulting in an UNDEF.
The obvious fix is to skip the reset of this shadow register
when no PMU is available, sidestepping the issue entirely.
If no PMU is available, the guest is not able to request
a virtual PMU anyway, so not doing nothing is the right thing
to do!
It is unlikely that this bug can hit any HW implementation
though, as they all provide a PMU. It has been found using nested
virt with the host KVM not implementing the PMU itself.
Fixes: ab9468340d ("arm64: KVM: Add access handler for PMCR register")
Reviewed-by: Alexandru Elisei <alexandru.elisei@arm.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201210083059.1277162-1-maz@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change OCOTP node name from ocotp-ctrl to efuse to be compliant with
yaml schema, it requires the nodename to be one of "eeprom|efuse|nvram".
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit 12fa1078efc871604d62e992cb8a038421b82096)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Compared to i.MX7D, i.MX8MM has different ocotp layout, so it should
NOT use "fsl,imx7d-ocotp" as ocotp's fallback compatible, remove it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
(cherry picked from commit b09802a03f0390fc115bf4ce4683645dc9b090bd)
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
