When booting with a ramdisk we bump the amount of memory reserved for
the device tree by FDT_RAMDISK_OVERHEAD. However we did not increase
the actual size in the device tree blob to match.
Its possible on boundary cases that we dont have enough memory according
to the device tree blob and get errors like:
WARNING: could not set linux,initrd-end FDT_ERR_NOSPACE
We can easily fix this by setting the device tree size at the same time
we bump the amount of memory reserved for the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
This is useful when we just want to wipe out the TLBs. There's currently
a function that resets the ddr tlbs to a different value; it is changed to
utilize this function. The new function can be used in conjunction with
setup_ddr_tlbs() for a board to temporarily map/unmap the DDR address
range as needed.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Fman device tree node binding allows for the entire Fman firmware binary
data to be embedded in the device tree. This eliminates the need to have
NOR flash mapped to Linux just so that the Fman driver can see the firmware.
The location of the Fman firmware is taken from the 'fman_ucode' environment
variable.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The ePAPR specification says that phandle properties should be called
"phandle", and not "linux,phandle". To facilitate the migration from
"linux,phandle" to "phandle", we update fdt_qportal() to use the new
function, fdt_create_phandle(). This function abstracts the creation of
phandle properties.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some P4080 rev1 errata work-arounds, notably erratum SERDES4, required a
bank soft-reset after the bank was configured and enabled, even though
enabling a bank causes it to reset. Because the reset was required for
multiple errata, it was not properly enclosed in an #ifdef, and so was
not removed with all the other rev1 errata work-arounds.
Erratum SERDES-8 says that the clocks for bank 3 needs to be enabled if
bank 2 is enabled, but this was not being done for SERDES protocols 0xF
and 0x10. The bank reset also happened to enable bank 3 (apparently an
undocumented feature). Simply removing the reset breaks these two
protocols.
It turns out that every time we call enable_bank(), we do want at least
one lane of the bank enabled, either because the bank is supposed to be
enabled, or because we need the clock from that bank enabled.
For erratum SERDES-A001, we don't want to modify srds_lpd_b[] when we
call enable_bank(), because that array is used elsewhere to determine if
the bank is available.
Note that the side effect of these changes is that the work-arounds for
these two errata are now linked. Specifically, if SERDES-A001 is
enabled, then we need SERDES-8 enabled as well.
Because this was the only SERDES bank soft-reset, there is no need to
implement a work-around for erratum SERDES-A003.
Also fix an off-by-one error in a printf().
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Ed Swarthout <swarthou@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add this option to allow boards to override the default read-to-write
turnaround time for better performance.
Signed-off-by: York Sun <yorksun@freescale.com>
Modify support for USB mode fixup:
- Add common support for USB mode and phy type
device tree fix-up for all USB controllers
mentioned in hwconfig string
- Fetch USB mode and phy type via hwconfig; if not
defined in hwconfig, then fetch them from env
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Checking width before setting DDR controller. SPD for DDR1 and DDR2 has
data width and primary sdram width. The latter one has different meaning
for DDR3.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In case of empty SPD or checksum error, fallback to raw timing on
supported boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We used to have fixed parameters for soldered DDR chips. This patch
introduces CONFIG_SYS_DDR_RAW_TIMING to enable calculation based on timing
data from DDR chip datasheet, implemneted in board-specific files or header
files.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On P1022/P1013 second USB controller is muxed with second
Ethernet controller. The current code to enable second USB
fails to properly clear pinmux bits used by ethernet. As a
result, Linux freezes when this controller is used. This
patch fixes the problem.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for 16-bit DDR bus. Also deal with system using 64- and 32-bit
DDR devices.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Only use DDR DIMM part number if SPD has valid length, to prevent from
display garbage in case SPD doesn't cover these fields.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If the bus width is 32-bit, burst chop should be disabled and burst length
should be 8. Read from SPD or other source to determine the width.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection for qp_info and liodn associated with Q/BMan. Also
rearrange setting of _tbl_sz variables to utilize existing ifdef
protection for things like FMAN.
Also add protection around setup_portals() call in corenet_ds board
code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add ifdef protection in LBC code to handle the case in which
CONFIG_SYS_BR0_PRELIM and CONFIG_SYS_OR0_PRELIM arent defined for a
build.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On a 8308 based board it was found that the PEX_GLK_RATIO register
(programmed in arch/powerpc/cpu/mpc83xx/pcie.c) was getting set to 0, This
was tracked to the fact that the pci express clock frequency was not being
assigned to the pciexp1_clk entry in the global data structure in file
arch/powerpc/cpu/mpc83xx/speed.c. Fix this and a similiar issue in
'do_clocks' command.
Signed-off-by: Bill Cook <cook@isgchips.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
CPO value and driver strength settings are board specifc.
Also allow SPD data fetch from any accessible I2C EEPROM.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Running on mpc837x without CONFIG_FSL_ESDHC leads to
i2c1_clk not being set at all. It is bound to clock
of encryption module. fix this.
Signed-off-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
We assumed that only a small set of compatiable strings would be needed
to find the PCIe device tree nodes to be fixed up. However on newer
platforms the simple rules no longer work. We need to allow specifying
the PCIe compatiable string for each individual SoC.
We introduce CONFIG_SYS_FSL_PCIE_COMPAT for this purpose and set it if
the default isn't sufficient.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Reword "The DIMM max tCKmin is ..." to "The DDR clock is faster than the slowest
DIMM(s) can support". Fixed interger type in printf as well.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The compatible property for the L2 cache node (on 85xx systems that don't
have a CPC) was using a value for the property length that did not match
the actual length of the property.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
APM errata CHIP_21 for the 405EX/EXr (from the rev 1.09 document dated
4/27/11) states that rev D processors may wake up with the wrong feature
set. This patch implements the APM-proposed workaround.
To enable this patch for your board, add the appropriate define for your
CPU to your board header file. See kilauea.h for more information. The
following variants are supported:
#define CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_NO_SECURITY
#define CONFIG_SYS_4xx_CHIP_21_405EXr_SECURITY
Please note that if you select the wrong define, your board will not
boot, and JTAG will be required to recover.
Tested on custom boards using:
CONFIG_SYS_4xx_CHIP_21_405EX_NO_SECURITY <sfalco@harris.com>
CONFIG_SYS_4xx_CHIP_21_405EX_SECURITY <eibach@gdsys.de>
Signed-off-by: Steve Falco <sfalco@harris.com>
Acked-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, some linker scripts are found by common code in config.mk.
Some are found using CONFIG_SYS_LDSCRIPT, but the code for that is
sometimes in arch config.mk and sometimes in board config.mk. Some
are found using an arch-specific rule for looking in CPUDIR, etc.
Further, the powerpc config.mk rule relied on CONFIG_NAND_SPL
when it really wanted CONFIG_NAND_U_BOOT -- which covered up the fact
that not all NAND_U_BOOT builds actually wanted CPUDIR/u-boot-nand.lds.
Replace all of this -- except for a handful of boards that are actually
selecting a linker script in a unique way -- with centralized ldscript
finding.
If board code specifies LDSCRIPT, that will be used.
Otherwise, if CONFIG_SYS_LDSCRIPT is specified, that will be used.
If neither of these are specified, then the central config.mk will
check for the existence of the following, in order:
$(TOPDIR)/board/$(BOARDDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/$(CPUDIR)/u-boot-nand.lds (only if CONFIG_NAND_U_BOOT)
$(TOPDIR)/board/$(BOARDDIR)/u-boot.lds
$(TOPDIR)/$(CPUDIR)/u-boot.lds
Some boards (sc3, cm5200, munices) provided their own u-boot.lds that
were dead code, because they were overridden by a CPUDIR u-boot.lds under
the old powerpc rules. These boards' own u-boot.lds have bitrotted and
no longer work -- these lds files have been removed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
- serial console on UART1
- Ethernet RMII over UCC4
- PHY SMSC LAN8700
- 64MB Flash
- 128 MB DDR2 RAM
- I2C
- bootcount
This board is similiar to the kmeter1 (8360) board,
so common config options are extracted into the
include/configs/km83xx-common.h file.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
cc: Kim Phillips <kim.phillips@freescale.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Singed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce new CONFIG_SYS_FSL_TBCLK_DIV on 85xx platforms because
different SoCs have different divisor amounts. All the PQ3 parts are
/8, the P4080/P4080 is /16, and P2040/P3041/P5020 are /32.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Bank powerdown through RCW[SRDS_LPD_Bn] for XAUI on FM2 and SGMII on FM1
are swapped.
Erratum SERDES-A001 says that if bank two is kept disabled and after bank
three is enabled, then the PLL for bank three won't lock properly. The
work-around is to enable and then disable bank two after bank three is
enabled.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Part of the SERDES9 erratum work-around is to set some bits in the SerDes
TTLCR0 register for lanes configured as XAUI, SGMII, SRIO, or AURORA. The
current code does this only for XAUI, so extend it to the other protocols.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES-8 requires all lanes of banks two
and three to be disabled (powered down) in the RCW. Display a warning
message if this is not the case.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the 'video-mode' environment variable (for Freescale chips that have a
DIU display controller) to designate the full video configuration. Previously,
the DIU driver used the 'monitor' variable, and it was used only to determine
the output video port.
The old definition of the "monitor" environment variable only determines
which video port to use for output. This variable was set to a number (0,
1, or sometimes 2) to specify a DVI, LVDS, or Dual-LVDS port. The
resolution was hard-coded into board-specific code. The Linux command-line
arguments needed to be hard-coded to the proper video definition string.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
A lot of boards set FT_FSL_PCI_SETUP directly in their board code
and don't check to see if CONFIG_PCI is actually defined. This
will cause the board compilation to fail if CONFIG_PCI is not
defined. The p1022ds board is one such example.
Instead of fixing every board this patch wraps FT_FSL_PCI_SETUP
around CONFIG_PCI so we can remove CONFIG_PCI and boards will
still build properly.
Signed-off-by: Matthew McClintock <msm@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
versioned SEC properties changed names during development, so
for now search and update LIODNs for both "secX.Y" and
"sec-vX.Y" based properties.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The workaround for ESDHC111 should also be applied on
P2040/P3041/P5010/P5020 SoCs.
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P2040, P3041, P5010, and P5020 all have internal USB PHYs that we
need to enable for them to function.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P3041DS & P5020DS boards are almost identical (except for the
processor in them). Additionally they are based on the P4080DS board
design so we use the some board code for all 3 boards.
Some ngPIXIS (FPGA) registers where reserved on P4080DS and now have
meaning on P3041DS/P5020DS. We utilize some of these for SERDES clock
configuration.
Additionally, the P3041DS/P5020DS support NAND.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rework and add some new APIs to the fsl_corenet_serdes code for use by
erratum and drivers.
* Rename serdes_get_bank() to serdes_get_bank_by_lane()
* Add serdes_get_first_lane returns which SERDES lane is used by device
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix fdt bportal to pass the bman revision number to kernel via device tree.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To make sure that machine change operation work successfully, change
timing parameters first before changing machine for chip select on IFC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
If FB address is defined specific address then don't grab memory for LCD
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
If a regions is reserved in the fdt, then it should not be used. Add
the memreserve regions to the lmb so that u-boot doesn't use them to
store the initrd.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The previous patch makes u-boot use the full accessible size of ram as
the default boot mapped size if CONFIG_SYS_BOOTMAPSZ is not defined,
which means boot_relocate_fdt() can be changed to depend solely on
CONFIG_OF_LIBFDT.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
This patch adds a function getenv_bootm_mapsize() for obtaining the
size of the early mapped region accessible by the kernel during early
boot. It defaults to CONFIG_SYS_BOOTMAPSZ, or if not defined,
defaults to getenv_bootm_size(), which in turn defaults to the size of
RAM.
getenv_bootm_mapsize() can also be overridden with a "bootm_mapsize"
environmental variable.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
For the calls to boot_relocate_fdt(), boot_get_cmdline(), and
boot_get_kbd(), the value of bootmem_base is always obtained by
calling getenv_bootm_low(). Since the value always comes from the
same source, the calling signature for those functions can be
simplified by making them call getenv_bootm_low() directly.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
The fsl_phy_enet_if enum was, essentially, the phy_interface_t enum.
This meant that drivers which used fsl_phy_enet_if to deal with
PHY interfaces would have to convert between the two (or we would have
to have them mirror each other, and deal with the ensuing maintenance
headache). Instead, we switch all clients of fsl_phy_enet_if over to
phy_interface_t, which should become the standard, anyway.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Detlev Zundel <dzu@denx.de>
This converts tsec to use the new PHY Lib. All of the old PHY support
is ripped out. The old MDIO driver is split off, and placed in
fsl_mdio.c. The initialization is modified to initialize the MDIO
driver as well. The powerpc config file is modified to configure PHYLIB
if TSEC_ENET is configured.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Detlev Zundel <dzu@denx.de>
Rename STANDALONE_LOAD_ADDR into CONFIG_STANDALONE_LOAD_ADDR
and allow that the architecture-specific default value gets
overwritten by defining the value in the board header file.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: Tsi Chung Liew <tsi-chung.liew@freescale.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
-msingle-pic-base is a new gcc option for ppc and
it reduces the size of my u-boot with 6-8 KB.
While at it, add -fno-jump-tables too to save a
few more bytes.
-msingle-pic-base will be in gcc 4.6, however
backported patches are available at
http://bugs.gentoo.org/show_bug.cgi?id=347281
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
The -fPIC flag belongs with -mrelocatable, move it there.
Also change -fPIC to -fpic as this produces smaller
binaries.
However, currently -mrelocatable promotes -fpic to -fPIC, a
fix for this is in upcoming gcc 4.6 or you can apply this small
patch to gcc:
diff --git a/gcc/config/rs6000/sysv4.h b/gcc/config/rs6000/sysv4.h
index 8da8410..e4b8280 100644
--- a/gcc/config/rs6000/sysv4.h
+++ b/gcc/config/rs6000/sysv4.h
@@ -227,7 +227,8 @@ do { \
} \
\
else if (TARGET_RELOCATABLE) \
- flag_pic = 2; \
+ if (!flag_pic) \
+ flag_pic = 2; \
} while (0)
#ifndef RS6000_BI_ARCH
--
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Removed clearing of L2 cache as SRAM as it is not necessary without ECC.
This also speeds up the booting process.
Signed-off-by: Fabian Cenedese <cenedese@indel.ch>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1010 and P1014 has v2.3 version of FSL eSDHC controller in which watermark
level register description has been changed:
9-15 bits represent WR_WML[0:6], Max value = 128 represented by 0x00
25-31 bits represent RD_WML[0:6], Max value = 128 represented by 0x00
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
PBL(pre-boot loader): SPI flash used as RCW(Reset Configuration Word) and
PBI(pre-boot initialization) source, CPC(CoreNet Platform Cache) used as
1M SRAM where PBL will copy whole U-BOOT image to, U-boot can boot from
CPC after PBL completes RCW and PBI phases.
Signed-off-by: Chunhe Lan <b25806@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For soc which have pin multiplex relation, some of them can't enable
simultaneously. This patch add environment var 'hwconfig' content
defination for them. you can enable some one function by setting
environment var 'hwconfig' content and reset board. Detail setting
please refer doc/README.p1022ds
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove the SERDES8 erratum work-around code that only applied to P4080
rev1, which is not supported by this version of U-Boot.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
renaming 85xx define CONFIG_NAND_OR_PRELIM to CONFIG_SYS_NAND_OR_PRELIM
and CONFIG_NAND_BR_PRELIM to CONFIG_SYS_NAND_BR_PRELIM to use the more
appropriate CONFIG_SYS prefix as well as be consistent with 83xx.
Signed-off-by: Matthew McClintock <msm@freescale.com>
cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* Added SDHCDCR register to GUR struct
* Added SDHCDCR_CD_INV define related to SDHCDCR
* Added Pin Muxing define related to TDM on P102x
Signed-off-by: Zhao Chenhui <b35336@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1021 has some QE pins which need to be set in pmuxcr register before
using QE functions. In this patch, pin QE0 and QE3 are set for UCC1 and
UCC5 in Eth mode. QE9 and QE12 are set for MII management. QE12 needs to
be released after MII access because QE12 pin is muxed with LBCTL signal.
Also added relevant QE support defines unique to P1021.
The P1021 QE is shared on P1012, P1016, and P1025.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
i.e, to those parts that have PHY_CLK_VALID bits in their USB
CONTROL registers:
mpc8308 WU_INT, PHY_CLK_SEL, USB_EN, WU_INT_EN, ULPI_INT_EN
mpc831x PHY_CLK_VALID, WU_INT, CLKIN_SEL, PHY_CLK_SEL, UTMI_PHY_EN,
PLL_RESET, REFSEL, OTG_PORT, KEEP_OTG_ON, LSF_EN, USB_EN,
ULPI_INT_EN
mpc834x USB_EN, ULPI_INT1_EN (MPH only), ULPI_INT0_EN
mpc837x USB_EN, ULPI_INT_EN
(mpc832x, mpc8360 don't have a USB_EHCI_FSL compatible controller)
this prevents non-831x parts from never completing cpu_init_f(),
because the (non-existent) PHY_CLK_VALID bit never gets set.
Reported-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
The numeric constants in the switch statements are replaced by #defines
added to the common ddr_spd.h header. This dramatically improves the
readability of the switch statments.
In addition, a few of the longer lines were cleaned up, and the DDR2
type for an SO-RDIMM module was added to the DDR2 switch statement.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current FreeScale MPC-8xxx DDR SPD interpreter is using full 64-bit
integer divide operations to convert between nanoseconds and DDR clock
cycles given arbitrary DDR clock frequencies.
Since all of the inputs to this are 32-bit (nanoseconds, clock cycles,
and DDR frequencies), we can easily restructure the computation to use
the "do_div()" function to perform 64-bit/32-bit divide operations.
On 64-bit this change is basically a no-op, because do_div is
implemented as a literal 64-bit divide operation and the instruction
scheduling works out almost the same.
On 32-bit PowerPC a fully accurate 64/64 divide (__udivdi3 in libgcc) is
over 1.1kB of code and thousands of heavily dependent cycles to compute,
all of which is linked from libgcc. Another 1.2kB of code comes in for
the function __umoddi3.
It should be noted that nothing else in U-Boot or the Linux kernel seems
to require a full 64-bit divide on my 32-bit PowerPC.
Build-and-boot-tested on the HWW-1U-1A board using DDR2 SPD detection.
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Acked-by: York Sun <yorksun@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We utilize the compatible string to find the node to add fsl,liodn
property to. However P3041 & P5020 don't have "fsl,p4080-pcie"
compatible for their PCIe controllers as they aren't backwards compatible.
Allow the macro's to specify the PCIe compatible to use to allow SoC
uniqueness. On P3041 & P5020 we utilize "fsl,qoriq-pcie-v2.2" for the
PCIe controllers.
Signed-off-by: Laurentiu TUDOR <Laurentiu.Tudor@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix up the device tree property associated with the IEEE 1588 timer
source frequency. Currently we only support the IEEE 1588 timer source
being the internal eTSEC system clock (for those SoCs with IEEE 1588
support). The eTSEC clock is ccb_clk/2.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the P1023 the Fman freq is equivalent to the system bus freq, not 1/2
of it. Also we only have one Fman so no need for the code to deal with
a second.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On CoreNet based SoCs (P2040, P3041, P4080, P5020) we have some
additional rules to determining the various frequencies that PME & FMan
IP blocks run at.
We need to take into account:
* Reduced number of Core Complex PLL clusters
* HWA_ASYNC_DIV (allows for /2 or /4 options)
On P2040/P3041/P5020 we only have 2 Core Complex PLLs and in such SoCs
the PME & FMan blocks utilize the second Core Complex PLL. On SoCs
like p4080 with 4 Core Complex PLLs we utilize the third Core Complex
PLL for PME & FMan blocks.
On P2040/P3041/P5020 we have the added feature that we can divide the
PLL down further by either /2 or /4 based on HWA_ASYNC_DIV. On P4080
this options doesn't exist, however HWA_ASYNC_DIV field in RCW should be
set to 0 and this gets a backward compatiable /2 behavior.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_FM_MURAM_SIZE varies from SoC to SoC to specify it in
config_mpc85xx.h for those parts with a Frame Manager.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
SDHC clock is equal to CCB on P1010 and P1014 not CCB/2.
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add defines for FSL_SATA_V2, # of DDR controllers, reset value of CCSRBAR
and SDHC erratum.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add Support for Freescale P1024/P1025 (dual core) and
P1015/P1016 (single core) processors.
P1024 is a variant of P1020 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA
P1025 is a variant of P1021 processor with a core frequency from
400Mhz to 667Mhz and comes in a 561-pin wirebond power-BGA
P1015 is a variant of P1024 processor with single core and P1016 is a
variant of P1025 processor with single core.
Added comments in config_mpc85xx.h to denote single core versions of
processors.
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the case the QE's microcode is stored in nand flash, we need to load it from
NAND flash to ddr first then the qe_init can get the ucode correctly.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Beside displaying RDIMM or UDIMM, this patch adds display of the model numbers
embedded in SPD.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
FSL PCIe controller v2.1:
- New MSI inbound window
- Same Inbound windows address as PCIe controller v1.x
Added new pit_t member(pmit) to struct ccsr_pci for MSI inbound window
FSL PCIe controller v2.2 and v2.3:
- Different addresses for PCIe inbound window 3,2,1
- Exposed PCIe inbound window 0
- New PCIe interrupt status register
Added new Interrupt Status register to struct ccsr_pci & updated pit_t array
size to reflect the 4 inbound windows.
To maintain backward compatiblilty, on V2.2 or greater controllers we
start with inbound window 1 and leave inbound 0 with its default value
(which maps to CCSRBAR).
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are some differences between CoreNet (P2040, P3041, P5020, P4080)
and and non-CoreNet (P1017, P1023) based SoCs in what features exist and
the memory maps.
* Rename various immap defines to remove _CORENET_ if they are shared
* Added P1023/P1017 specific memory offsets
* Only setup LIODNs or LIODN related code on CORENET based SoCs
(features doesn't exist on P1023/P1017)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add P1023 (dual core) & P1017 (single core) specific information:
* SERDES Table
* Added P1023/P1017 to cpu_type_list and SVR list
(fixed issue with P1013 not being sorted correctly).
* Added P1023/P1027 to config_mpc85xx.h
* Added new LAW type introduced on P1023/P1017
* Updated a few immap register/defines unique to P1023/P1017
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We can simplify some cpu/SoC level initialization by moving it to be
after the environment and non-volatile storage is setup as there might
be dependancies on such things in various boot configurations.
For example for FSL SoC's with QE if we boot from NAND we need it setup
to extra the ucode image to initialize the QE. If we always do this
after environment & non-volatile storage is working we can have the code
be the same regardless of NOR, NAND, SPI, MMC boot.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move some processor specific QE defines into config_mpc85xx.h and use
QE_MURAM_SIZE to cleanup some ifdef mess in the QE immap struct.
Also fixed up some comment style issues in immap_qe.h
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move fsl_ddr_get_spd into common mpc8xxx/ddr/main.c as most boards
pretty much do the same thing. The only variations are in how many
controllers or DIMMs per controller exist. To make this work we
standardize on the names of the SPD_EEPROM_ADDRESS defines based on the
use case of the board.
We allow boards to override get_spd to either do board specific fixups
to the SPD data or deal with any unique behavior of how the SPD eeproms
are wired up.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Every 85xx board implements fsl_ddr_get_mem_data_rate via get_ddr_freq()
and every 86xx board uses get_bus_freq(). If implement get_ddr_freq()
as a static inline to call get_bus_freq() we can remove
fsl_ddr_get_mem_data_rate altogether and just call get_ddr_freq()
directly.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We've been utilizing board_lmb_reserve to reserve the boot page for MP
systems. We can just move this into arch_lmb_reserve for 85xx & 86xx
systems rather than duplicating in each board port.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In a manner similar to passing ethernet stashing parameters into device
tree for "gianfar", extend the support to the "fsl,etsec2" as well.
Signed-off-by: Pankaj Chauhan <pankaj.chauhan@freescale.com>
Signed-off-by: Sandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove declerations of fsl_ddr_set_memctl_regs in board files with and
place it into a common header.
Based on patch from Poonam Aggrwal.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Integrated Flash Controller (IFC) is used to access the external
NAND Flash, NOR Flash, EPROM, SRAM and Generic ASIC memories.Four chip
selects are provided in IFC so that maximum of four Flash devices can be
hooked, but only one can be accessed at a given time.
Features supported by IFC are,
- Functional muxing of pins between NAND, NOR and GPCM
- Support memory banks of size 64KByte to 4 GBytes
- Write protection capability (only for NAND and NOR)
- Provision of Software Reset
- Flexible Timing programmability for every chip select
- NAND Machine
- x8/ x16 NAND Flash Interface
- SLC and MLC NAND Flash devices support with
configurable
page sizes of upto 4KB
- Internal SRAM of 9KB which is directly mapped and
availble at
boot time for NAND Boot
- Configurable block size
- Boot chip select (CS0) available at system reset
- NOR Machine
- Data bus width of 8/16/32
- Compatible with asynchronous NOR Flash
- Directly memory mapped
- Supports address data multiplexed (ADM) NOR device
- Boot chip select (CS0) available at system reset
- GPCM Machine (NORMAL GPCM Mode)
- Support for x8/16/32 bit device
- Compatible with general purpose addressable device
e.g. SRAM, ROM
- External clock is supported with programmable division
ratio
- GPCM Machine (Generic ASIC Mode)
- Support for x8/16/32 bit device
- Address and Data are shared on I/O bus
- Following Address and Data sequences can be supported
on I/O bus
- 32 bit I/O: AD
- 16 bit I/O: AADD
- 8 bit I/O : AAAADDDD
- Configurable Even/Odd Parity on Address/Data bus
supported
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are only
ever connected on SERDES.
Updated MPC85xx_PORDEVSR_IO_SEL & MPC85xx_PORDEVSR_IO_SEL_SHIFT
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1011, P1012, P1015, P1016, P1020, P1021, P1024, & P1025 SoCs require
that we initialize the SERDES registers if the lanes are configured for
PCIe. Additionally these devices PCIe controller do not support ASPM
and we have to explicitly disable it.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Enable workaround for errata ELBC A001, ESDHC 111 & SATA A001 on
P1022/P1013 SoCs.
Also updated P1022DS config to properly enable CONFIG_FSL_SATA_V2.
Signed-off-by: Jiang Yutang <b14898@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
The fix for errata workaround is to avoid covering physical address
0xff000000 to 0xffffffff during the implementation.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
rcw_en bit is only available for DDR3 controllers. It is a reserved bit on
DDR1 and DDR2 controllers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
To recognize DIMMs with ECC capability by testing ECC bit only. Not to be
confused by Address Parity bit.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
commit 8aba9dceeb
Divides variable of linker flags to LDFLAGS-u-boot and LDFLAGS
breaks the usage of --gc-section to build nand_spl. We still need linker option
--gc-section for every uboot image, not only the main one. LDFLAGS_FINAL passes
the --gc-sections to each uboot image.
To get the proper linker flags, we use LDFLAGS and LDFLAGS_FINAL to replace
PLATFORM_LDFLAGS in the Makefile of each nand_spl board.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
There is a small ordering issue in the master core in that we need to
make sure the disabling of the timebase in the SoC is visible before we
set the value to 0. We can simply just read back the value to
synchronizatize the write, before we set TB to 0.
Reported-by: Dan Hettena
Tested-by: Dan Hettena
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The POST word is stored in a spare register in the PIC on MPC8[5/6]xx
processors. When interrupt_init() is called, this register gets reset
which resulted in all POST_RAM POSTs not being ran due to the corrupted
POST word. To resolve this, store off POST word before the PIC is
reset, and restore it after the PIC has been initialized.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Copying directly from ECM/PQ3 is not correct for how CoreNet based
platforms handle boot page translation.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The write recovery time of both registers should match. Since mode register
doesn't support cycles of 9,11,13,15, we should use next higher number for
both registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR data rate is higher than 1200MT/s or controller interleaving is
enabled, additional cycle for write-to-read turnaround is needed to satisfy
dynamic ODT timing.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Board support for the Guntermann & Drunck DLVision-10G.
Adds support for multiple FPGAs per board for gdsys 405ep
architecture.
Adds support for dual link osd hardware for gdsys 405ep.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Use SPMR instead of HRCWL when calculating clocks as HCRWL
may be changed and the CPU will not pick up all changes
until there is a POR. u-boot will think SPMF has changed and get
the clocks wrong.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fix a problem for the pcie enumeration when the mpc83xx
pcie controller is connected with switch or we use both of the two
pcie controller.
Signed-off-by: Leo Liu <liucai.lfn@gmail.com>
fix codingstyle and compiler warning: 'pcie_priv' defined but not used
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The P1013 is a single core version of P1022 and thus should use the
p1022_serdes.c code. It was acciently pointing to p1013_serdes.c which
doesn't exist.
Reported-by: Renaud Barbier <renaud.barbier@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
calibrate to incorrect values
These two workarounds must be implemented together because they touch
common registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This polling loop is not required normally, unless specifically stated in
workaround.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Linker needs to use the proper endian/bfd flags even when doing partial linking.
LDFLAGS_u-boot sets linker option which is called it when U-boot is built
(u-boot final).
LDFLAGS sets necessary option by partial linking (use in cmd_link_o_target).
CC: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
ctrl_regs.c: In function 'set_ddr_sdram_mode_2':
ctrl_regs.c:690:6: warning: unused variable 'i'
'i' is only used by DDR3 code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Future SoC (like the P1010) replace the LBC controller with the new IFC
(Integrated Flash Controller) so ensure we properly protect code that is
related to the LBC.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Hwconfig is called before relocating. Use the new hwconfig APIs.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend board specific parameters to include cpo, write leveling override
Extend write leveling sample to 0xf
Adding rcw overrid for quad-rank RDIMMs
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added fsl_ddr_get_version() function to for DDR3 to poll DDRC IP version
(major, minor, errata) to determine if unique mode registers are available.
If true, always use unique mode registers. Dynamic ODT is enabled if needed.
The table is documented in doc/README.fsl-ddr. This function may also need
to be extend for future other platforms if such a feature exists.
Enable address parity and RCW by default for RDIMMs.
Change default output driver impedance from 34 ohm to 40ohm. Make it 34ohm for
quad-rank RDIMMs.
Use a formula to calculate rodt_on for timing_cfg_5.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch exposes more registers which can be used by the DDR drivers or
interactive debugging. U-boot doesn't use all the registers in DDRC.
When advanced tuning is required, writing to those registers is needed.
Add writing to cdr1, cdr2, err_disable, err_int_en and debug registers
Add options to override rcw, address parity to RDIMMs.
Use array for debug registers.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add fsl_ddr:ecc=on in hwconfig. If ECC is enabled in board configuration file,
ECC can be turned on/off by this switch. If this switch is omitted, it is ON by
default.
Updated hwconfig calls to use local buffer.
Syntax is
hwconfig=fsl_ddr:ecc=on
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add new headers that capture common defines for a given SoC/processor
rather than duplicating that information in board config.h and random
other places.
Eventually this should be handled by Kconfig & defconfigs
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
There are several users of the hwconfig APIs (8xxx DDR) before we have
the environment properly setup. This causes issues because of the
numerous ways the environment might be accessed because of the
non-volatile memory it might be stored in. Additionally the access
might be so early that memory isn't even properly setup for us.
Towards resolving these issues we provide versions of all the hwconfig
APIs that can be passed in a buffer to parse and leave it to the caller
to determine how to allocate and populate the buffer.
We use the _f naming convention for these new APIs even though they are
perfectly useable after relocation and the environment being ready.
We also now warn if the non-f APIs are called before the environment is
ready to allow users to address the issues.
Finally, we convert the 8xxx DDR code to utilize the new APIs to
hopefully address the issue once and for all. We have the 8xxx DDR code
create a buffer on the stack and populate it via getenv_f().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Add P2040 SoC specific information:
* SERDES Table
* Added p2040 to cpu_type_list and SVR list
* Added number of LAWs for p2040
* Set CONFIG_MAX_CPUS to 4 for p2040
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1014 is similar to the P1010 processor with the following differences:
- 16bit DDR with ECC. (P1010 has 32bit DDR w/o ECC)
- no eCAN interface. (P1010 has 2 eCAN interfaces)
- Two SGMII interface (P1010 has 3 SGMII)
- No secure boot
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Key Features include of the P1010:
* e500v2 core frequency operation of 500 to 800 MHz
* Power consumption less than 5.0 W at 800 MHz core speed
* Dual SATA 3 Gbps controllers with integrated PHY
* Dual PCI Express controllers
* Three 10/100/1000 Mbps enhanced triple-speed Ethernet controllers (eTSECs)
* TCP/IP acceleration and classification capabilities
* IEEE 1588 support
* Lossless flow control
* RGMII, SGMII
* DDR3 with support for a 32-bit data interface (40 bits including ECC),
up to 800 MHz data rate 32/16-bit DDR3 memory controller
* Dedicated security engine featuring trusted boot
* TDM interface
* Dual controller area networks (FlexCAN) controller
* SD/MMC card controller supporting booting from Flash cards
* USB 2.0 host and device controller with an on-chip, high-speed PHY
* Integrated Flash controller (IFC)
* Power Management Controller (PMC)
* Four-channel, general-purpose DMA controller
* I2C controller
* Serial peripheral interface (SPI) controller with master and slave support
* System timers including a periodic interrupt timer, real-time clock,
software watchdog timer, and four general-purpose timers
* Dual DUARTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Dipen Dudhat <dipen.dudhat@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MPC85xx_SERDES1_ADDR was defined wrong as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES2_OFFSET.
It should be as
CONFIG_SYS_IMMR + CONFIG_SYS_MPC85xx_SERDES1_OFFSET.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Rather than defining it config.mk we can set it in config.h and remove
config.mk from several boards that don't need it.
We mimic what 4xx does and introduce CONFIG_RESET_VECTOR_ADDRESS for
config.h to set.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
This patch adds fsl_ddr_sdram_size to only calculate the ddr sdram size, in
case that the DDR SDRAM is initialized in the 2nd stage uboot and should not
be intialized again in the final stage uboot.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There's no compelling reason to have the output on bootup or the
"flinfo" command print "flash" in uppercase, so use the proper case
where appropriate.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Simultaneous FCM and GPCM or UPM operation may erroneously trigger bus
monitor timeout. Set timeout to maximum to avoid.
Based on a patch from Lan Chunhe <b25806@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CoreNet Platform Cache single-bit data error scrubbing will cause data
corruption. Disable the feature to workaround the issue.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CoreNet Platform Cache single-bit tag error scrubbing will cause tag
corruption. Disable the feature to workaround the issue.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move the parsing of hwconfig to determine if to use spd into common code
so we can share it across all boards instead of duplicating it
everywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
False multi-bit ECC errors will be reported by the eSDHC buffer which
can trigger a reset request.
We disable all ECC error checking on SDHC.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The default value of the SRS, VS18 and VS30 and ADMAS fields in the host
controller capabilities register (HOSTCAPBLT) are incorrect. The default
of these bits should be zero instead of one.
Clear these bits out when we read HOSTCAPBLT.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Do not issue a manual asynchronous CMD12. Instead, use a (software)
synchronous CMD12 or AUTOCMD12 to abort data transfer.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the needed defines and code to utilize the common 8xxx srio init
code to setup LAWs and modify device tree if we have SRIO enabled on a
board.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Moved the SRIO init out of corenet_ds and into common code for
8xxx/QorIQ processors that have SRIO. We mimic what we do with PCIe
controllers for SRIO.
We utilize the fact that SRIO is over serdes to determine if its
configured or not and thus can setup the LAWs needed for it dynamically.
We additionally update the device tree (to remove the SRIO nodes) if the
board doesn't have SRIO enabled.
Introduced the following standard defines for board config.h:
CONFIG_SYS_SRIO - Chip has SRIO or not
CONFIG_SRIO1 - Board has SRIO 1 port available
CONFIG_SRIO2 - Board has SRIO 2 port available
(where 'n' is the port #)
CONFIG_SYS_SRIOn_MEM_VIRT - virtual address in u-boot
CONFIG_SYS_SRIOn_MEM_PHYS - physical address (for law setup)
CONFIG_SYS_SRIOn_MEM_SIZE - size of window (for law setup)
[ These mimic what we have for PCI and PCIe controllers ]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
This change does the following:
- Adds printing of negotiated link width. This information can be
useful when debugging PCIe issues.
- Makes it optional for boards to implement board_serdes_name().
Previously boards that did not implement it would print unsightly
output such as "PCIE1: Connected to <NULL>..."
- Rewords the PCIe boot output to reduce line length and to make it
clear that the "base address XYZ" value refers to the base address of
the internal processor PCIe registers and not a standard PCI BAR
value.
- Changes "PCIE" output to the standard "PCIe"
Before change:
PCIE1: connected to <NULL> as Root Complex (base addr ef008000)
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIE1: Bus 00 - 05
PCIE2: connected to <NULL> as Endpoint (base addr ef009000)
PCIE2: Bus 06 - 06
After change:
PCIe1: Root Complex of PEX8518 Switch, x4, regs @ 0xef008000
01:00.0 - 10b5:8518 - Bridge device
02:01.0 - 10b5:8518 - Bridge device
02:02.0 - 10b5:8518 - Bridge device
02:03.0 - 10b5:8518 - Bridge device
PCIe1: Bus 00 - 05
PCIe2: Endpoint of VPX Fabric A, x2, regs @ 0xef009000
PCIe2: Bus 06 - 06
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Since all the PCIe controllers are connected over SERDES on the SoCs we
can utilize is_serdes_configured() to determine if a controller is
enabled. After which we can setup the ATMUs and LAWs for the controller
in a common fashion and allow board code to specify what the controller
is connected to for reporting reasons.
We also provide a per controller (rather than all) for some systems that
may have special requirements.
Finally, we refactor the code used by the P1022DS to utilize the new
generic code.
Based on patch by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we passed in a specifically named struct pci_controller to
determine if we had setup the particular PCI bus. Now we can search for
the struct so we dont have to depend on the name or the struct being
statically allocated.
Introduced new find_hose_by_cfg_addr() to get back a pci_controller struct
back by searching for it means we can do things like dynamically allocate
them or not have to expose the static structures to all users.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
We set the L1 dache register with a bogus register value. Need to be
using 'r3' instead of 'r0'.
Reported-by: John Traill <john.traill@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add spaces to cause the informational prints to line up with
the ones from init_func_ram() in board.c. Output now looks like
this:
....
DRAM: Detected 4096 MB of memory
This U-Boot only supports < 4G of DDR
You could rebuild it with CONFIG_PHYS_64BIT
DDR: 2 GiB (DDR2, 64-bit, CL=5, ECC off)
....
The prints from lbc_sdram_init() have also been modified to line
line up and changed to start with "LBC SDRAM" instead of the
confusing "SDRAM".
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This config option is for an erratum workaround; rename it to be more
clear. Also, drop it from config files don't need it and were
undefining it.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
sdram_init() is used to initialize sdram on the lbc. Rename it
accordingly.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correct initdram to use phys_size_t to represent the size of
dram; instead of changing this all over the place, and correcting
all the other random errors I've noticed, create a
common initdram that is used by all non-corenet 85xx parts. Most
of the initdram() functions were identical, with 2 common differences:
1) DDR tlbs for the fixed_sdram case were set up in initdram() on
some boards, and were part of the tlb_table on others. I have
changed them all over to the initdram() method - we shouldn't
be accessing dram before this point so they don't need to be
done sooner, and this seems cleaner.
2) Parts that require the DDR11 erratum workaround had different
implementations - I have adopted the version from the Freescale
errata document. It also looks like some of the versions were
buggy, and, depending on timing, could have resulted in the
DDR controller being disabled. This seems bad.
The xpedite boards had a common/fsl_8xxx_ddr.c; with this
change only the 517 board uses this so I have moved the ddr code
into that board's directory in xpedite517x.c
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some platforms might want to override the default wimge=0 for
DDR. Add CONFIG_SYS_PPC_DDR_WIMGE for those platforms to use.
This will initially only be used by TQM85xx, but could be
useful for other boards or testing going forward. Note that
the name of this define is not 85xx-specific. WIMGE is a
fairly universal concept, so any ppc platforms that require
different WIMGE settings for DDR can use the same #define.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have serdes support for all 85xx/86xx/Pxxx chips we can
replace the is_fsl_pci_cfg() code with the is_serdes_configured().
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the ability to determine if a given IP block connected on SERDES is
configured. This is useful for things like PCIe and SRIO since they are
only ever connected on SERDES. This mimics the code we have in place
for the 85xx platforms.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Created a section in the Makefile for SoC specific SERDES code. Also
added P1013 SERDES (use P1022 SERDES code).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Patch 8ef583a0 [miiphy: convert to linux/mii.h] introduced a small
problem in the ppc4xx miiphy.c version. This patch fixes this problem.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The include/miiphy.h header duplicates a lot of things from linux/mii.h.
So punt all the things that overlap to keep the API simple and to make
merging between U-Boot and Linux simpler.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
In some usages of inline assembly, hard-coded registers were
specified when a scratch register should have been used instead.
Signed-off-by: Timur Tabi <timur@freescale.com>
The following commit:
commit 882b7d726f
Author: Mike Frysinger <vapier@gentoo.org>
Date: Wed Oct 20 03:41:17 2010 -0400
do_reset: unify duplicate prototypes
missed the 74xx_7xx and mpc86xx arches and the ppmc7xx board do_reset()
functions which resulted in build errors such as:
cpu.c:128: error: conflicting types for 'do_reset'
include/command.h:102: error: previous declaration of 'do_reset' was here
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
By rearranging the linker script we get support for
relocation of -fpic for free.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Use common ppc4xx linker script for xilinx ppc440 and ppc405 related boards.
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fix a problem for the pcie enumeration for mpc83xx cpus. Without
this we will not get correct value in hose->regions[...].
The pointer *reg in function mpc83xx_pcie_init_bus() shall not be changed.
Because we will use this pointer as a parameter to call function
mpc83xx_pcie_register_hose().
Signed-off-by: Baidu Boy <liucai.lfn@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This fixes the compiling error for the board which doesn't have NOR flash
(so CONFIG_FLASH_BASE is not defined)
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some systems need to relocate the env_addr pointer early because the
location it points to will get invalidated before env_relocate is
called. One example is on systems that might use a L2 or L3 cache
in SRAM mode and initialize that cache from SRAM mode back to being
a cache in cpu_init_r.
We set this on the 85xx boards that have support for NAND, SPI, or
SDHC/MMC boot support as they use a secondary cache in SRAM mode and
need the env_addr pointer relocated since we change from SRAM to normal
cache mode in cpu_init_r.
Also removed CONFIG_SYS_SPL as its not used anywhere.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
After the removal of COLD/WARM start flags my mpc8321
board didn't boot anymore.
Trial and error suggests that map/remap_flash_by_xxx needs
to wait after updating LBLAWAR1 to make sure the the change has
reached the HW before continuing with the code that depends on it.
Final fix suggested by Scott Wood.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The duplication of the do_reset prototype has gotten out of hand,
and they're not all in sync. Unify them all in command.h.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
When the cache is enabled in SDRAM we need to flush not only the global
data area but also the bd_info struct in relocate_code. This patch now
flushed the complete dcache (all dcache lines) via flush_dcache() instead
of adding a flush_dcache_range() call for bd_info since this is faster.
Signed-off-by: Stefan Roese <sr@denx.de>
Use the return value of cmd_usage instead of ignoring this
and returning a 1.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Timur Tabi <timur@freescale.com>
Acked-by: Stefan Roese <sr@denx.de>
This commit adapts 4xx boards for partial linking with --gc-sections.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Tirumala Marri <tmarri@apm.com>
Cc: David Updegraff <dave@cray.com>
Cc: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Larry Johnson <lrj@acm.org>
Cc: Peter De Schrijver <p2@mind.be>
Cc: Niklaus Giger <niklaus.giger@netstal.com>
Cc: Daniel Poirot <dan.poirot@windriver.com>
Acked-by: Stefan Roese <sr@denx.de>
The switch from archive libraries to partial linking has introduced a
number of problems, that are non-trivial to solve. For example, it is
no longer possible to include individual object files in the linker
script as we did before for example in the case of boards with
embedded environment to fill up the gap caused by the need to align
the environment on flash erase block boundaries.
The best (but unfortunately not easiest) approach to address this
problem is to enable -ffunction-sections (and -fdata-sections) so
we can again (and even in much finer granularity) place certain code
where we want it. When doing this step, it seems only consequent to
also add --gc-sections which has the added benefit of reducing the
memory footprint of the U-Boot image (both in flash and in RAM).
Unfortunately, this requires changes to a lot of linker scripts.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Stefan Roese <sr@denx.de>
As we try to get rid of board specific config.mk files we must
provide a way for board specific settings of the LDSCRIPT variable
(path to the linker script) where needed.
We now implement the following hierarchy:
- Highest priority has a "#define CONFIG_SYS_LDCONFIG" in the board
config file.
- If CONFIG_SYS_LDCONFIG is not set, and the system is booting from
NAND (CONFIG_NAND_SPL is set), then a board specific linker
script board/$(BOARDDIR)/u-boot-nand.lds gets used.
- If we are not booting from NAND, we test if a processor specific
linker script arch/powerpc/cpu/$(CPU)/u-boot.lds exists; if so we
use that.
- As default, arch/powerpc/config.mk gets used.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Andy Fleming <afleming@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
So far, only the BAB7xx board would call the initialise_w83c553f()
function for the WINBOND 83C553 chip, even though some other boards
(HIDDEN_DRAGON, Sandpoint8240, Sandpoint8245) enabled it in their
board configuration. These boards were also missing other config
settings needed for that, which resulted in build errors like this:
drivers/pci/libpci.o:(.got2+0x84): undefined reference to `ide_bus_offset'
Switch arch/powerpc/lib/board.c to call initialise_w83c553f() not on a
per-board base, but when a WINBOND_83C553 in enabled in a
configuration (like BAB7xx), and disable it in the boards that had
this set so far.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Yusdi Santoso <yusdi_santoso@adaptec.com>
Cc: Jim Thompson <jim@musenki.com>
Acked-by: Stefan Roese <sr@denx.de>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
The fixup procedure just stored a constant value in the
fixup table rather than just adjusting the table.
Although that doesn't seem to do any harm, it prevents
relocation more that once.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Use CONFIG_SYS_MONITOR_BASE instead of CONFIG_SYS_TEXT_BASE in early
init code so we can share the same code with NAND or NOR boot and not
have additional ifdefs in here.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix u-boot-nand.lds and u-boot-nand_spl.lds according to:
Author: Peter Tyser <ptyser@xes-inc.com>
Date: Wed Sep 29 14:05:56 2010 -0500
commit fbe53f59bd
85xx: Use gc-sections to reduce image size
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By now, the majority of architectures have working relocation
support, so the few remaining architectures have become exceptions.
To make this more obvious, we make working relocation now the default
case, and flag the remaining cases with CONFIG_NEEDS_MANUAL_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE
No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.
Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Commit 29c6fbe "MPC5121: Add USB EHCI support" renamed
CONFIG_SYS_MPC8xxx_USB_ADDR into CONFIG_SYS_FSL_USB_ADDR but missed
to update arch/powerpc/cpu/mpc83xx/cpu_init.c, resulting in:
cpu_init.c: In function 'cpu_init_f':
cpu_init.c:332: error: 'CONFIG_SYS_MPC8xxx_USB_ADDR' undeclared (first use in this function)
cpu_init.c:332: error: (Each undeclared identifier is reported only once
cpu_init.c:332: error: for each function it appears in.)
make[1]: *** [/work/wd/tmp-ppc/arch/powerpc/cpu/mpc83xx/cpu_init.o] Error 1
Fix this.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Kim Phillips <kim.phillips@freescale.com>
If a NOR flash is write protected it can not be initialized/detected so
add the ability for boards to skip NOR initialization on bootup. A
board can skip NOR initialization by implementing the
board_flash_wp_on() function.
Signed-off-by: John Schmoller <jschmoller@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
CC: sr@denx.de
Acked-by: Stefan Roese <sr@denx.de>
On an XPedite5370 over 11KBytes were saved:
Before:
text data bss dec hex filename
332456 33364 33476 399296 617c0 ./u-boot
After:
text data bss dec hex filename
321075 33836 33476 388387 5ed23 ./u-boot
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On an XPedite5170 over 11KBytes were saved:
Before:
text data bss dec hex filename
319488 28700 33204 381392 5d1d0 ./u-boot
After:
text data bss dec hex filename
307663 29144 33204 370011 5a55b ./u-boot
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously io_sel=0xe incorrect stated PCIE1 was enabled. Also add
support for the mpc8640's PCIE2 interface.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some OSes require that secondary cores not be initialized when they
are booted (eg VxWorks). By default when U-Boot is compiled with the
CONFIG_MP option all secondary cores are brought out of reset and held
in spinloops. Setting the "mp_holdoff" environment variable to 'yes'
or '1' will cause U-Boot to leave secondary cores in their default
state.
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When DDR controller interleaving is eabled and less than all bank (chip-select)
interleaving is seletected, the unused chip-select should be disabled.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
800, 900, 1000, 1200MT/s data rate parameters are added for fixed sdram
setting. SPD based parameters and fixed parameters can be toggled by hwconfig.
To use fixed parameters,
hwconfig=fsl_ddr:sdram=fixed
To use SPD parameters,
hwconfig=fsl_ddr:ctlr_intlv=cacheline,bank_intlv=cs0_cs1
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The memory test is performed after DDR initialization when U-boot stills runs
in flash and cache. On recent mpc85xx platforms, the total memory can be more
than 2GB. To cover whole memory, it needs be mapped 2GB at a time using a
sliding TLB window. After the testing, DDR is remapped with up to 2GB memory
from the lowest address as normal.
If memory test fails, DDR DIMM SPD and DDR controller registers are dumped for
further debugging.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A worker function setup_ddr_tlbs_phys() is introduced to implement more
control on physical address mapping.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add a common helper that will set the PHY connection type based on enum.
We use this on eTSEC, UCC, and will with Fman in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Have a common enum for phy types that we use in the UCC driver. We will
also use this enum for dealing with phy connection fixup in the device
tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The routines boot_ramdisk_high, boot_get_cmdline and boot_get_kbd
are currently enabled by various combinations of CONFIG_M68K,
CONFIG_POWERPC and CONFIG_SPARC.
Use CONFIG_SYS_BOOT_<FEATURE> defines instead.
CONFIG_SYS_BOOT_RAMDISK_HIGH
CONFIG_SYS_BOOT_GET_CMDLINE
CONFIG_SYS_BOOT_GET_KBD
Define these as appropriate in arch/include/asm/config.h files.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Acked-by: Wolfgang Denk <wd@denx.de>
The fixup routine must not fixup NULL pointers.
Problem can be seen by
char *testfun(void) __attribute__((weak));
char *(*myfun)(void) = testfun;
Then add
printf("myfun:%p, &myfun:%p\n", myfun, &myfun);
before relocation and after relocation.
myfun should be NULL in both cases but it is not.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.
Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This puts the board info struct in a known state and allows the removal
of other code which initialized board info fields to 0.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
pumping line-rate traffic though a p4080 rev.2, which
is configured to encrypt packets prior to forwarding through
an IPsec tunnel, gets this error:
of_platform ffe302000.jq: DECO: desc idx 22: LIODN error. DECO was trying
to share from itself or from another DECO but the two Non-SEQ LIODN
values didn't match or the "shared from" DECO's Descriptor required that
the SEQ LIODNs be the same and they aren't.
Since high traffic rates cause DECOs to begin to start sharing
shared descriptors amongst themselves, and DECOs inherit job queue
LIODNs when accessing shared descriptors, and a recently discovered
rev.2 h/w erratum requires all sharing job queues in a partition
have same liodn assignment, reassign the first job queue's liodn
assignment to the rest.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCU_E board has long reached EOL, and support for it is no longer
relevant in current versions of U-Boot. Remove it.
Signed-off-by: Wolfgang Denk <wd@denx.de>
