There was a typo in the EMIF driver. It went un-noticed
because it affected only when automatic detection is enabled
and even then half the memory was configured and identified
properly.
Reported-by: Rockefeller <rockefeller.lin@innocomm.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
TPS power IC is controlled using a GPIO (gpio_wk7).
This GPIO should be maintained at logic 1 always. As
such an internal pull-up on this pin will do the job,
driving the GPIO outuput is not needed. This will avoid
the need of using GPIO library in SPL and also may
save some power.
Signed-off-by: Aneesh V <aneesh@ti.com>
The vector is not correctly setup in armv7 except for OMAP3.
Correcting this.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Aneesh V <aneesh@ti.com>
This allows SPL to have default implementation of
save_boot_params(), useful for SoCs that do
not intend to override this default implementation
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Aneesh V <aneesh@ti.com>
We were not disabling external caches before jumping
to kernel. We were flushing all caches including
external caches and disabling caches globally in
CP15 System Control register. Apparently this is not
enough.
The bootstrap loader in Linux kernel that does decompression
enables data-caches again, flush them after use and disable
them before jumping to kernel proper. However, it's not aware
of the external caches.
Since we have left external cache enabled, external cache will
get used once caches are enabled globally, but it's not flushed
because decompressor is not aware of external caches. When it
jumps to kernel with caches disabled globally, we have stale
data in the external cache and a coherency problem.
This was breaking the boot for OMAP4 with latest mainline
kernel. The solution is to disable external caches in
cleanup_before_linux(). With this fix kernel is booting again.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Aneesh V <aneesh@ti.com>
There is no need to have such a function twice.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix:
pwm.c: In function 'pwm_config':
pwm.c:85:16: warning: variable 'timer_rate_hz' set but not used
[-Wunused-but-set-variable]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Configuration header(CH) is 512 byte header attached to an OMAP
boot image that will help ROM code to initialize clocks, SDRAM
etc and copy U-Boot directly into SDRAM. CH can help us in
by-passing SPL and directly boot U-boot, hence it's an alternative
for SPL. However, we intend to support both CH and SPL for OMAP4/5.
Initialization done through CH is limited and is not equivalent
to that done by SPL. So U-Boot has to distinguish between the
two cases and handle them accordingly. This patch takes care
of doing this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add the emif configurations required for omap5 soc.Add the
correct ddr part configurations required for omap5 evm board.
EDB8164B3PH from ELPIDA is the part used on the board.
Also changes are done to retain some part of the code
common for OMAP4/5 and keep only the remaining in the Soc
specific directories.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Adding the correct configurations required for
dplls, clocks, for omap5 Soc.
Also changes are done to retain some part of the code common
for OMAP4/5 and move only the remaining to the Soc specific
directories.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds the minimal support for OMAP5. The platform and machine
specific headers and sources updated for OMAP5430.
OMAP5430 is Texas Instrument's SOC based on ARM Cortex-A15 SMP architecture.
It's a dual core SOC with GIC used for interrupt handling and SCU for cache
coherency.
Also moved some part of code from the basic platform support that can be made
common for OMAP4/5. Rest is kept out seperately. The same approach is followed
for clocks and emif support in the subsequent patches.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Much of omap4 soc support code can be reused for omap5.
Move them to the omap-common directory to facilitate
this.
Signed-off-by: sricharan <r.sricharan@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In addition to ensuring that PERCLK remains at least 2.5 times slower
than the AHB clock, certain steps need to be followed to ensure robust
operation of PERCLK when reconfiguring the PERCLK clock source.
To properly configure the PERCLK clock source, the following steps are
required:
1.In the CCGR registers, gate the clocks to all PERCLK-dependent
modules.
2.Select the desired input clock for the PERCLK root clock (to be either
source from the peripherals main source clock or the
lp_apm clock source). Refer to the CMCBR register, perclk_lp_apm_sel bit.
3.Configure the perclk_pred1, perclk_pred2, and perclk_podf dividers
to the desired setting. Refer to the CBCDR register for details.
4.In the CCGR registers, enable the desired clocks for the
PERCLK-dependent module clocks.
If these steps aren't followed, GPT timer may stop and the kernel stops
at "Calibrating delay loop".
Signed-off-by: Terry Lv <r65388@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently OMAP SPL code does all the initialization but does not set the
gd->have_console value so no output is actually performed. This patch
sets gd->have_console to 1.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
U-Boot Makefiles contain a number of tests for compiler features etc.
which so far are executed again and again. On some architectures
(especially ARM) this results in a large number of calls to gcc.
This patch makes sure to run such tests only once, thus largely
reducing the number of "execve" system calls.
Example: number of "execve" system calls for building the "P2020DS"
(Power Architecture) and "qong" (ARM) boards, measured as:
-> strace -f -e trace=execve -o /tmp/foo ./MAKEALL <board>
-> grep execve /tmp/foo | wc -l
Before: After: Reduction:
==================================
P2020DS 20555 15205 -26%
qong 31692 14490 -54%
As a result, built times are significantly reduced, typically by
30...50%.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Albert Aribaud <albert.aribaud@free.fr>
cc: Graeme Russ <graeme.russ@gmail.com>
cc: Mike Frysinger <vapier@gentoo.org>
Tested-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Matthias Weisser <weisserm@arcor.de>
Tested-by: Sanjeev Premi <premi@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Tested-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-arm:
ARM: Add Calxeda Highbank platform
dkb: make mmc command as default enabled
Marvell: dkb: add mmc support
ARM: pantheon: add mmc definition
davinci: remove config.mk file from the sources
ARM:AM33XX: Add support for TI AM335X EVM
ARM:AM33XX: Added timer support
ARM:AM33XX: Add emif/ddr support
ARM:AM33XX: Add clock definitions
ARM:AM33XX: Added support for AM33xx
omap3/emif4: fix registers definition
davinci: remove obsolete macro CONFIG_EMAC_MDIO_PHY_NUM
davinci: emac: add support for more than 1 PHYs
davinci: emac: add new features to autonegotiate for EMAC
da850evm: Move LPSC configuration to board_early_init_f()
omap4_panda: Build in cmd_gpio support on panda
omap: Don't use gpio_free to change direction to input
mmc: omap: Allow OMAP_HSMMC[23]_BASE to be unset
OMAP3: overo : Add environment variable optargs to bootargs
OMAP3: overo: Move ethernet CS4 configuration to execute based on board id
OMAP3: overo : Use ttyO2 instead of ttyS2.
da830: add support for NAND boot mode
dm36x: revert cache disable patch
dm644X: revert cache disable patch
devkit8000: Add malloc space
omap: spl: fix build break due to changes in FAT
OMAP3 SPL: Provide weak omap_rev_string
omap: beagle: Use ubifs instead of jffs2 for nand boot
omap: overo: Disable pull-ups on camera PCLK, HS and VS signals
omap: overo: Configure mux for gpio10
SPL: Add DMA library
omap3: Add interface for omap3 DMA
omap3: Add DMA register accessors
omap3: Add Base register for DMA
arm, davinci: add missing LSPC define for MMC/SD1
U-Boot/SPL: omap4: Make ddr pre-calculated timings as default.
DaVinci: correct MDSTAT.STATE mask
omap4: splitting padconfs into common, 4430 and 4460
omap4: adding revision detection for 4460 ES1.1
omap4: replacing OMAP4_CONTROL with OMAP4430_CONTROL
gplug: fixed build error as a result of code cleanup patch
kirkwood_spi: add dummy spi_init()
gpio: mvmfp: reduce include platform file
ARM: orion5x: reduce dependence of including platform file
serial: reduce include platform file for marvell chip
ARM: kirkwood: reduce dependence of including platform file
ARM: armada100: reduce dependence of including platform file
ARM: pantheon: reduce dependence of including platform file
Armada100: Add env storage support for Marvell gplugD
Armada100: Add SPI flash support for Marvell gplugD
Armada100: Add SPI support for Marvell gplugD
SPI: Add SPI driver support for Marvell Armada100
dreamplug: initial board support.
imx: fix coding style
misc: pmic: drop old Freescale's pmic driver
MX31: mx31pdk: use new pmic driver
MX31: mx31ads: use new pmic driver
MX31: mx31_litekit: use new pmic driver
MX5: mx53evk: use new pmic driver
MX5: mx51evk: use new pmic driver
MX35: mx35pdk: use new pmic driver
misc: pmic: addI2C support to pmic_fsl driver
misc: pmic: use I2C_SET_BUS in pmic I2C
MX5: efikamx/efikasb: use new pmic driver
MX3: qong: use new pmic driver
RTC: Switch mc13783 to generic pmic code
MX5: vision2: use new pmic driver
misc: pmic: Freescale PMIC switches to generic PMIC driver
misc:pmic:samsung Enable PMIC driver at GONI target
misc:pmic:max8998 MAX8998 support at a new PMIC driver.
misc:pmic:core New generic PMIC driver
mx31pdk: Remove unneeded config
mx31: provide readable WEIM CS accessor
MX51: vision2: Set global macros
I2C: Add i2c_get/set_speed() to mxc_i2c.c
ARM: Update mach-types
devkit8000: Add config to enable SPL MMC boot
devkit8000: protect board_mmc_init
arm, post: add missing post_time_ms for arm
cosmetic, post: Codingstyle cleanup
arm, logbuffer: make it compileclean
tegra2: Enable MMC for Seaboard
tegra2: Add more pinmux functions
tegra2: Rename PIN_ to PINGRP_
tegra2: Add more clock functions
tegra2: Clean up board code a little
tegra2: Rename CLOCK_PLL_ID to CLOCK_ID
clocks.c:606:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'
clocks.c:633:2: warning: format '%08x' expects type 'unsigned int', but argument
2 has type 'u32 * const'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
board.c:43:2: warning: format '%08lX' expects type 'long unsigned int', but
argument 2 has type 'u32'
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Add basic support for Calxeda Highbank platform. Only minimal support with
serial and SATA are included.
Signed-off-by: Jason Hobbs <jason.hobbs@calxeda.com>
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds AM33xx emif/ddr support along with board specific
defines.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds basic support for AM33xx which is based on ARMV7
Cortex A8 CPU.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
gpio_free() should not have the side effect of setting the line to input since this prevents the gpio command from being able to set a line as output.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
FAT library now uses malloc() and free(). But SPL doesn't
have heap until now. Setup a heap in SDRAM to fix this issue.
However this increases SPL footprint beyond the available SRAM
budget. So, compile out some fancy features in the SDARM init
bring back footprint under control
CC: Sandeep Paulraj <s-paulraj@ti.com>
CC: Wolfgang Denk <wd@denx.de>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
We add an weak version of omap_rev_string in omap-common/spl.c
and while at it drop the omap3 version. Move the prototype over
to <asm/omap_common.h> with the other SPL functions.
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Not all padconfs are the same between 4430 and 4460, so instead of
working around this with an if, we should have an specific padconf
structure for both chips (like handling the differences between the LEDs
GPIOs and TPS).
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP4460 has a different set of values for the ID code, so moving the
old ones to be related just with 4430.
Signed-off-by: Ricardo Salveti de Araujo <ricardo.salveti@linaro.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Fix checkpatch warning and errors in several i.MX related files.
While at it also address a checkpatch warning at arch/arm/cpu/armv7/mx5/soc.c
regarding the usage of extern in a C file.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This adds support for changing pinmux functions of pin groups. This is done
by defining a PMUX_FUNC_... enum which can be used to select the function for
each group using pinmux_set_func(). It is also possible to enable
pullup/pulldown, and the existing tristate functionality is retained.
Also provided is a means of configuring a list of pingroups by providing a
configuration table to pinmux_config_table().
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
The pin groupings are better named PINGRP, since on Tegra2 they refer to
multiple pins.
Sorry about this, but better to get it right now when there is only a small
amount of code affected.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
This adds most of the clock functions required by board and driver code:
-query and adjust peripheral clocks
-query and adjust PLLs
-reset and enable control
These functions are plumbed in as required.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Rename CLOCK_PLL_ID to CLOCK_ID which takes account of the fact that the
code now deals with both PLL clocks and source clocks.
This also tidied up the assert() to match the one sent upstream, and fixes
an error in the PWM id.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Warren <twarren@nvidia.com>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
There is a rather subtle build problem where the build time stamp is not
updated for out-of-tree builds if there exists an in-tree build which
has a valid timestamp file. So if you do an in-tree build, then an
out-of-tree build your timestamp will not change.
The correct timestamp_autogenerated.h lives in the object tree, but it
is not always found there. The source still lives in the source tree and
when compiling version.h, it includes timestamp_autogenerated.h. Since
the current directory is always searched first, this will come from the
source tree rather than the object tree if it exists there. This affects
dependency generation also, which means that common/cmd_version.o will not
even be rebuilt if you have ever done an in-tree build.
A similar problem exists with the version file.
This change moves both files into the 'generated' subdir, which is already
used for asm-offsets.h. Then timestamp.h and version.h are updated to
include the files from there.
There are other places where these generated files are included, but I
cannot see why these don't just use the timestamp.h and version.h headers.
So this change also tidies that up.
I have tested this with in- and out-of-tree builds, but not SPL. I have
looked at various other options for fixing this, including sed on the dep
files, -I- and -include flags to gcc, but I don't think they can be made
to work. Comments welcome.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Tested-by: Jason Liu <Jason.hui@linaro.org>
Building without option CONFIG_DISPLAY_CPUINFO leads to
this warning:
sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems
with missing defines if a board does not use mmc or nand. This includes
adding spl_ prefix to some functions which are now public. spl_image_t is now
a public type. Added some of the common functions to omap-common.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Implements the saving of boot params passed by OMAP3 ROM code.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Support for the new spl structure. Using the interface defined by Aneesh V for
OMAP4
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3 relied on the memory config done by X-loader or Configuration Header. This
has to be reworked for the implementation of a SPL. This patch configures RAM
bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000
are added to mem.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.
This is done to prepare for OMAP3 integration.
This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch contains the generic changes required after
change to generic API in the previous patch.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
- Use -EINVAL consistently. -1 was used in many places.
- Removed one-liner static functions that were used only
once. Replaced the content as necessary.
- Combines implementation of functions omap_get_gpio_dataout()
and omap_get_gpio_datain(). To do so, new static function
_get_gpio_direction() was added.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:
clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
which is used to provide 120MHz to USB EHCI
This allows EHCI to work on BeagleBoard XM
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In case of AM3517 and AM3505 (which is OMAP3 varients), IVA2 and
ISP-CAMERA modules have been removed. So add check for cpu_family before
enabling clocks for these modules, else this impacts subsequent
power consumption and system suspend/resume functionality.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Ranjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
AM/DM37x is another OMAP3 variant, where the GFX clock has been
boosted to 192MHz/200MHz. So fix the GFX_DIV value for this change.
HW Errata: Due to dependency of TV out clock of 54MHz, it is not
possible to configure GFX to 192MHz. So as per HW errats, the
recommended GFX clock is 200MHz (=CORE_CLK/2).
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Remove the flush of boundary cache-lines done as part
of invalidate on a non cache-line boundary aligned
buffer
Also, print a warning when this situation is recognized.
Signed-off-by: Aneesh V <aneesh@ti.com>
set-way operations need a DSB after them to ensure the
operation is complete. DMB may not be enough. Use DSB
after all operations instead of DMB.
Signed-off-by: Aneesh V <aneesh@ti.com>
These functions provide access to the high resolution microsecond timer
and tidy up a global variable in the code.
Signed-off-by: Simon Glass <sjg@chromium.org>
There was already a command to show the processor clocks
for PowerPC (clocks). For i.MX, the "clockinfo" command
was introduce. The patch sets the same command name used on
PowerPC.
A nasty and not needed newline is also dropped in the help for
the command.
Signed-off-by: Stefano Babic <sbabic@denx.de>
This is a port of the official PLL errata workaround from Freescale to
mainline u-boot.
The PLL's in the i.MX51 processor can go out of lock due to a metastable
condition in an analog flip-flop when used at high frequencies.
This workaround implements an undocumented feature in the PLL (dither
mode), which causes the effect of this failure to be much lower (in terms
of frequency deviation), avoiding system failure, or at least decreasing
the likelihood of system failure.
Signed-off-by: David Jander <david@protonic.nl>
TPS62361 is the new power supply used in OMAP4460 that
supplies vdd_mpu.
VCORE1 from Phoenix supplies vdd_core and VCORE2 supplies
vdd_iva. VCORE3 is not used in OMAP4460.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add mkimage support for OMAP boot image
- Add support for OMAP boot image(MLO) generation in the new
SPL framework
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Add MMC raw and FAT mode boot support for OMAP
- Provide a means by which parameters passed by ROM-code
can be saved in u-boot.
- Save boot mode related information passed by OMAP4 ROM-code
and use it to determine where to load the u-boot from
- Assumes that the image has a mkimage header. Gets the
payload size and load address from this header. If the
header is not detected assume u-boot.bin as payload
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Provide alternate implementations of board_init_f()
board_init_r() for OMAP spl.
- Provide linker script
- Initialize global data
- Add serial console support
- Update CONFIG_SYS_TEXT_BASE to allow for SPL's bss and move
it to board config header from config.mk
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- Allow SPL to have .bss disjoint from rest of the image
- Allow for .bss setup in CONFIG_SPL_BUILD case too.
- Take care of the special case where relocation offset = 0.
- Compile out exception handling code and install a simpler
vector
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Identify SDRAM devices connected to EMIF automatically:
LPDDR2 devices have some Mode Registers that provide details
about the device such as the type, density, bus width
etc. EMIF has the capability to read these registers. If there
are no devices connected to a given chip-select reading mode
registers will return junk values. After reading as many such
registers as possible and matching with expected ranges of
values the driver can identify if there is a device connected
to the respective CS. If we identify that a device is connected
the values read give us complete details about the device.
This along with the base AC timings specified by JESD209-2
allows us to do a complete automatic initialization of
SDRAM that works on all boards.
Please note that the default AC timings specified by JESD209-2
will be safe for all devices but not necessarily optimal. However,
for the Elpida devices used on Panda and SDP the default timings
are both safe and optimal.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Calculate EMIF register values based on AC timing parameters
from the SDRAM datasheet and the DDR frequency rather than
using the hard-coded values.
For a new board the user doen't have to go through the tedious
process of calculating the register values. Instead, just
provide the AC timings from the device data sheet as input
and the driver will automatically calculate the register values.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Add support for:
1. DPLL locking
2. Initialization of clock domains and clock modules
3. Setting up the right voltage on voltage rails
This work draws upon previous work done for x-loader by:
Santosh Shilimkar <santosh.shilimkar@ti.com>
Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
- separate mux settings into essential and non essential parts
- essential part is board independent as of now(so move it
to SoC directory). Will help in having single SPL for all
boards.
- Non-essential part(the pins not essential for u-boot to function)
need to be phased out eventually.
- Correct mux data by aligning to the latest settings in x-loader
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The array of strings corresponding to cpu revision is
used only when CONFIG_DISPLAY_CPUINFO is selected - in
the function print_cpuinfo().
Enclose definition of this array in #ifdef...#endif for
the same.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
In some circumstances, reset_timer_masked() was called be timer_init() in
order to perform architecture specific timer initialisation. In such
cases, the required code in reset_timer_masked() has been moved into
timer_init()
This check was broken. r3 does not contain the silicon revision anymore, so
we need to reload it. Also, this errata only applies to i.MX51.
Signed-off-by: David Jander <david@protonic.nl>
Acked-by: Stefano Babic <sbabic@denx.de>
cpu_init_crit can be skipped, but the code is still enabled requiring a
platform to supply lowlevel_init.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Albert ARIBAUD <albert.aribaud@free.fr>
On i.MX5, the asm-offsets.h file is not yet generated as it should be.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
As implemented now the timer used to implement __udelay counts
to 0xffffffff and then gets stuck there because the the programmed
reload value is 0xffffffff. This value is not only wrong but
illegal according to the reference manual.
One can reproduce the bug by leaving a board at the u-boot prompt
for sometime then issuing a sleep command. The sleep will hang
forever.
The timer is a count up timer that reloads as it rolls over
from 0xffffffff so the correct load value is 0.
Change TIMER_LOAD_VAL from 0xffffffff to 0 and introduce
a new constant called TIMER_OVERFLOW_VAL set to 0xffffffff.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
- Enable I-cache on bootup
- Enable MMU and D-cache immediately after relocation
- Do necessary initialization before enabling d-cache and MMU
- Changes to cleanup_before_linux()
- Make changes according to the new framework
Signed-off-by: Aneesh V <aneesh@ti.com>
Replace the cache related CONFIG flags with more meaningful
names. Following are the changes:
CONFIG_L2_OFF -> CONFIG_SYS_L2CACHE_OFF
CONFIG_SYS_NO_ICACHE -> CONFIG_SYS_ICACHE_OFF
CONFIG_SYS_NO_DCACHE -> CONFIG_SYS_DCACHE_OFF
Signed-off-by: Aneesh V <aneesh@ti.com>
V2:
* Changed CONFIG_L2_OFF -> CONFIG_SYS_NO_L2CACHE
V4:
* Changed all three flags to the final names suggested as above
and accordingly changed the commit message
- Add a framework for layered cache maintenance
- separate out SOC specific outer cache maintenance from
maintenance of caches known to CPU
- Add generic ARMv7 cache maintenance operations that affect all
caches known to ARMv7 CPUs. For instance in Cortex-A8 these
opertions will affect both L1 and L2 caches. In Cortex-A9
these will affect only L1 cache
- D-cache operations supported:
- Invalidate entire D-cache
- Invalidate D-cache range
- Flush(clean & invalidate) entire D-cache
- Flush D-cache range
- I-cache operations supported:
- Invalidate entire I-cache
- Add maintenance functions for TLB, branch predictor array etc.
- Enable -march=armv7-a so that armv7 assembly instructions can be
used
Signed-off-by: Aneesh V <aneesh@ti.com>
Based on ST-Ericsson internal git repo.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: John Rigby <john.rigby@linaro.org>
CC: Albert Aribaud <albert.aribaud@free.fr>
This patch added set_mmc_clk for external clock control.
c210 didn't support host clock control.
So We need external_clock_control function for c210.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
S5PC210 SoC have two cpu revisions, and have some difference.
So, support the cpu revision for each revision.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
SROM config code is made common for S5P series of boards.
smdkc100.c now refers to s5p-common/sromc.c for SROM related
subroutines.
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Removed boot_flash_* extern variables.
boot_flash_type was totally unused. The other ones were actually constants, so
they have been replaced with #defines in the board config files.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
CONFIG_OMAP34XX must be checked for existence, not value.
Signed-off-by: Luca Ceresoli <luca.ceresoli@comelit.it>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.aribaud@free.fr>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
factor out boot cause function to common code to avoid
the duplicate code in each board support package
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Use the global data instead of bss variable, replace as follow.
count_value -> removed
timestamp -> tbl
lastdec -> lastinc
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Albert ARIBAUD <albert.aribaud@free.fr>
This is common pwm driver of S5P.
Signed-off-by: Donghwa Lee <dh09.lee@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Monitor protection region in FLASH did not cover .rel.dyn
and .dynsym sections, because it uses __bss_start to compute
monitor_flash_len. Use _end instead.
Add _end to linker scripts for end of u-boot image
Add _end_ofs to all the start.S.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
Currently, _end is used for end of BSS section. We want _end to mean
end of u-boot image, so we rename _end to __bss_end__ first.
Signed-off-by: Po-Yu Chuang <ratbert@faraday-tech.com>
S5PC210 is a 32-bit RISC and Cortex-A9 Dual Core based micro-processor.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Because of the bss area is cleared after relocation, we've lost pointers.
This patch fixed it.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
The usage of bss values in drivers before initialisation of bss is forbidden.
In that special case some data in .rel.dyn gets corrupted.
This patch is the same as recently applied for arm926js architecture.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Heiko Schocher <hs@denx.de>
Add initial support for Freescale MX53 processor,
- Add the iomux support and the pin definition,
- Add the regs definition, clean up some unused def from mx51,
- Add the low level init support, make use the freq input of setup_pll macro
Signed-off-by: Jason Liu <r64343@freescale.com>
It can be optimised out by the compiler otherwise resulting
in obscure errors like a board not booting.
This has been documented in README since 2006 when these were
first fixed up for GCC 4.x.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Fix some additional places.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-By: Albert ARIBAUD <albert.aribaud@free.fr>
Reuse the gd->tbl value for timestamp and add gd->lastinc for lastinc bss
values in the OMAP timer driver.
The usage of bss values in drivers before initialisation of bss is forbidden.
In that special case some data in .rel.dyn gets corrupted.
Signed-off-by: Dirk Behme <dirk.behme@gmail.com>
Tested-by: Steve Sakoman <steve.sakoman@linaro.org>
Tested-by: John Rigby <john.rigby@linaro.org>
Tested-by: Nishanth Menon <nm@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
I doubt the stack_setup() was defective before:
we load the current location of _start and compare against destination
of relocate_code(). If we are already there we shoud skip the
relocation and jump over to clear_bss. Before the clear_bss was also skipped.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
r8 is used for global_data and should therefore be left alone!
For C code the compiler flag --fixed-r8 does the job, but in assembler
we need to be aware of that fact.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
In case we are still at relocation target address before relocation we
do not need to load the registers needed for relocation. We should
instead skip the whole relocation part and jump over to clear_bss
immediately.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
This patch uses r1 as scratch register for copy_loop(). Therefore we do
not longer need r7 for the storage of relocate_code()'s 'addr_moni' (the
destination address of relocation).
Therefore r7 can be used later on for other purposes.
Signed-off-by: Andreas Biemann <andreas.devel@googlemail.com>
suggested from Daniel Hobi<daniel.hobi@schmid-telecom.ch>
Tested on following boards:
arm1136: qong
armv7: omap3_beagle
arm926ejs: magnesium, tx25
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Daniel Hobi <daniel.hobi@schmid-telecom.ch>
cc: Albert ARIBAUD <albert.aribaud@free.fr>
This patch fixes build errors in the vexpress system:
- Removed sys_proto.h requirement from syslib.c.
- Switched vexpress to the default armv7 linker script.
- Renamed TEXT_BASE to CONFIG_SYS_TEXT_BASE.
Signed-off-by: Matt Waddel <matt.waddel@linaro.org>
Because of count_value is set to tcnb4 register,
should be get from this register when call udelay function.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
With addition of "dram_init_banksize()" function from Heiko,Schocher
(commit ID: 561142af20), the DRAM size
is getting configured wrongly to 512Mb (CS0 & CS1).
So fix it to 256Mb.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The patch is to support getting FEC MAC address from fuse bank.
Signed-off-by: Jason Liu <r64343@freescale.com>
Tested-by: Stefano Babic <sbabic@denx.de>
DECLARE_GLOBAL_DATA_PTR is currently defined within the scope
of function while it is a global pointer. Change the scope of
definition to replicate it's global scope. This seems to help
gcc 4.5 optimizations as well.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Before this commit, weak symbols were not overridden by non-weak symbols
found in archive libraries when linking with recent versions of
binutils. As stated in the System V ABI, "the link editor does not
extract archive members to resolve undefined weak symbols".
This commit changes all Makefiles to use partial linking (ld -r) instead
of creating library archives, which forces all symbols to participate in
linking, allowing non-weak symbols to override weak symbols as intended.
This approach is also used by Linux, from which the gmake function
cmd_link_o_target (defined in config.mk and used in all Makefiles) is
inspired.
The name of each former library archive is preserved except for
extensions which change from ".a" to ".o". This commit updates
references accordingly where needed, in particular in some linker
scripts.
This commit reveals board configurations that exclude some features but
include source files that depend these disabled features in the build,
resulting in undefined symbols. Known such cases include:
- disabling CMD_NET but not CMD_NFS;
- enabling CONFIG_OF_LIBFDT but not CONFIG_QE.
Signed-off-by: Sebastien Carlier <sebastien.carlier@gmail.com>
older ld emitted all ELF relocations in input sections named
.rel.dyn, whereas newer ld uses names of the form .rel*. The
linker script only collected .rel.dyn input sections. Rewrite
to collect all .rel* input sections.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
since commit 3667cbeed5
on beagle board the second sdram bank didn;t longer
work. Since this patch sdram settings just get copied
from bank a, but CMD_NOP, CMD_PRECHARGE, CMD_AUTOREFRESH
are not executed and after that mr register is also
not updated. This patch adds this for the bank b.
Signed-off-by: Heiko Schocher <hs@denx.de>
cc: Steve Sakoman <steve@sakoman.com>
cc: Sandeep Paulraj <s-paulraj@ti.com>
cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
For ARM systems, before ELF relocation was introduced,
CONFIG_SKIP_RELOCATE_UBOOT coul be used to prevent *COPYING* the
U-Boot image from whereever it was loaded to it's link address
(CONFIG_SYS_TEXT_BASE). The name was badly chosen, as no relocation
was performed at all, it was just a memcpy().
With ELF relocation, this does not work like that any more, and
related boards need to be fixed anyway. So don't keep this relict any
longer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
When this define was introduced, the idea was to provide a soft
migration path for ARM boards to get adapted to the new relocation
support. However, other recent changes led to a different
implementation (ELF relocation), where this no longer works. By now
CONFIG_SYS_ARM_WITHOUT_RELOC does not only not help any more, but it
actually hurts because it obfuscates the actual code by sprinkling it
with lots of dead and non-working debris.
So let's make a clean cut and drop CONFIG_SYS_ARM_WITHOUT_RELOC.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Tested-by: Reinhard Meyer <u-boot@emk-elektronik.de>
The patch removes the warning:
clock.c:291: warning: initialization from incompatible pointer type
after constification of args[]
Signed-off-by: Stefano Babic <sbabic@denx.de>
Remove u-boot.lds from mx5 and use the common u-boot.lds
of cpu layer. This patch also fix the building errors:
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_start'
arch/arm/cpu/armv7/start.o: In function `_rel_dyn_end_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__rel_dyn_end'
arch/arm/cpu/armv7/start.o: In function `_dynsym_start_ofs':
arch/arm/cpu/armv7/start.S:283: undefined reference to `__dynsym_start'
Signed-off-by: Jason Liu <r64343@freescale.com>
