The pumpkin board is made by Gossamer Engineering and is using
a MediaTek SoC. The board currently comes in two available version:
MT8516 SoC and MT8167 SoC.
The board provides the following IOs: eMMC, NAND, SD card, USB type-A,
Ethernet, Wi-Fi, Bluetooth, Audio (jack out, 2 PDM port, 1 analog in),
serial over USB, and an expansion header.
Additionally there is a HDMI port, DSI port, and camera port only
on the MT8167 version of the board.
The board can be powered by battery and/or via a USB Type-C port and
is using a PMIC MT6392.
The eMMC and NAND are sharing pins and cannot be used together.
This commit is adding the basic boot support for the Pumpkin MT8516
board on the eMMC.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
recently added gpio hog patch was "in discussion"
state with Simon Glass. This patch now adds most
of comments from Simon Glass.
Signed-off-by: Heiko Schocher <hs@denx.de>
Upcoming patches want to add decompression to use cases that are no
longer directly related to booting. It makes sense to retain a single
decompression routine, but it should no longer be in bootm.c (which is
not compiled for all configurations). This patch moves
bootm_decomp_image() to image.c and renames it to image_decomp() in
preparation of those upcoming patches.
Signed-off-by: Julius Werner <jwerner@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fix warning around handle_decomp_error being unused]
Signed-off-by: Tom Rini <trini@konsulko.com>
ttyO2 console enables legacy CONFIG_SERIAL_OMAP driver in kernel.
Nowadays it's preferred to use the generic CONFIG_SERIAL_8250_OMAP
driver, which being enabled via ttyS2 console. Both drivers are enabled
in multi_v7_defconfig and in omap2plus_defconfig, for compatibility
reasons. Let's switch to ttyS2 console, to be sure that standard 8250
serial driver is used.
Similar behavior can be also achieved by enabling
CONFIG_SERIAL_8250_OMAP_TTYO_FIXUP option in kernel, but it's better not
to rely on that, as it can be disabled or removed after transitional
period.
Right now on DRA7/AM57x platforms the 8250-omap driver is being probed
first, and omap-serial driver is only probed if the first one failed.
It can be seen from uart3 definition in arch/arm/boot/dts/dra7-l4.dtsi:
compatible = "ti,dra742-uart", "ti,omap4-uart";
So the kernel already uses 8250 driver. This change basically allows
kernel developers to throw away the omap-serial driver and associated
compatibility options. Similar discussions [1,2] have started several
years ago, so it should be safe to do that now.
[1] https://patchwork.kernel.org/patch/6198471/
[2] http://processors.wiki.ti.com/index.php/Sitara_Linux_UART_-_Switching_to_8250_Driver
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Andrew F. Davis <afd@ti.com>
[trini: Update omap5_uevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
linux-mainline with multi_v7_defconfig + Android configs takes more
space than regular TI Android kernel and bootm will fail to load it.
Let's increase max kernel size up to 64 MiB to make it possible to run
such kernel.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The DA8850-evm supports DM_I2C and boots with SPL_DM, so we can
drop some of the code which disables DM_I2C in SPL. This
patch removes some #undef's now rendered obsolete.
Signed-off-by: Adam Ford <aford173@gmail.com>
OHCI was added with DM_USB support, so there are a few unneeded
items in the header file that can be removed. This also
unifies da850evm with NOR and NAND booting options so all have
OHCI support.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Migrate da850_am18xxevm]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch enables the pinmuxing to support gpio_57 for phy reset
and fixes the pinmuxing for the ECHI tranceiver. The clocks
don't appear to by fully enabled yet, so OMAP-EHCI on am3517 is
still not yet working, but we're one step closer.
Signed-off-by: Adam Ford <aford173@gmail.com>
The SOM-LV boards support the OMAP EHCI driver using port 2.
With the driver updated to support device tree, this patch sets
the corresponding pin muxing for the tranceiver as well as the
reset pin.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add pinctrl macros for J721E SoC. These macro definitions are
similar to that of AM6, but adding new definitions to avoid
any naming confusions in the soc dts files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
TISCI protocol supports for enabling the device either with exclusive
permissions for the requesting host or with sharing across the hosts.
There are certain devices which are exclusive to Linux context and
there are certain devices that are shared across different host contexts.
So add support for getting this information from DT by increasing
the power-domain cells to 2.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Certain drivers want to attach private data corresponding to each
power domain. This data might be specific be to the drvier. So add
a priv entry into the power_domain structure.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Any host while requesting for a device can request for its exclusive
access. If an exclusive permission is obtained then it is the host's
responsibility to release the device before the software entity on
the host completes its execution. Else any other host's request for
the device will be nacked. So add a command that releases all the
exclusive devices that is acquired by the current host. This should
be used with utmost care and can be called only at the end of the
execution.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add and expose a new processor shutdown API that wraps the two TISCI
messages involved in initiating a core shutdown. The API will first
queue a message to have the DMSC wait for a certain processor boot
status to happen followed by a message to trigger the actual shutdown-
with both messages being sent without waiting or requesting for a
response. Note that the processor shutdown API call will need to be
followed up by user software placing the respective core into either
WFE or WFI mode.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Sysfw provides an option for requesting exclusive access for a
device using the flags MSG_FLAG_DEVICE_EXCLUSIVE. If this flag is
not used, the device is meant to be shared across hosts. Once a device
is requested from a host with this flag set, any request to this
device from a different host will be nacked by sysfw. Current tisci
driver enables this flag for every device requests. But this may not
be true for all the devices. So provide a separate commands in driver
for exclusive and shared device requests.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Now that we removed all legacy boards selecting TI_EMAC we can
completely convert the driver code to using the driver model.
This patch also updates all remaining users of davinci_emac.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Tested-by: Adam Ford <aford173@gmail.com> #am3517-evm & da850-evm
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We typically use same set of distro images (yocto, debian, fedora, etc.)
on both QEMU RISC-V virt machine and SiFive Unleashed board.
With growing kernel and ramdisk images, we need to re-adjust default
U-Boot environment variables. The config header for QEMU RISC-V virt
machine has been already updated to handle bigger kernel and ramdisk
images hence this patch updates SiFive FU540 config header accordingly.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
Tested-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
The LS1021A-TSN is a development board built by VVDN/Argonboards in
partnership with NXP.
It features the LS1021A SoC and the first-generation SJA1105T Ethernet
switch for prototyping implementations of a subset of IEEE 802.1 TSN
standards.
Supported boot media: microSD card (via SPL), QSPI flash.
Rev. A of the board uses a Spansion S25FL512S_256K serial flash, which
is 64 MB in size and has an erase sector size of 256KB (therefore,
flashing the RCW would erase part of U-Boot).
Rev. B and C of the board use a Spansion S25FL256S1 serial flash, which
is only 32 MB in size but has an erase sector size of 64KB (therefore
the RCW image can be flashed without erasing U-Boot).
To avoid the problems above, the U-Boot base address has been selected
at 0x100000 (the start of the 5th 256KB erase sector), which works for
all board revisions. Actually 0x40000 would have been enough, but
0x100000 is common for all Layerscape devices.
eTSEC3 is connecting directly to SJA1105 via an RGMII fixed-link, but
SJA1105 is currently not supported by uboot. Therefore, eTSEC3 is
disabled.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Mingkai Hu <mingkai.hu@nxp.com>
Signed-off-by: Jianchao Wang <jianchao.wang@nxp.com>
Signed-off-by: Changming Huang <jerry.huang@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
[Vladimir] Code taken from https://github.com/openil/u-boot (which
itself is mostly copied from ls1021a-iot) and adapted with the following
changes:
- Add a008850 errata workaround
- Converted eTSEC, MMC to DM to avoid all build warnings
- Plugged in distro boot feature, including support for extlinux.conf
- Added defconfig for QSPI boot
- Added the board/freescale/ls1021atsn/README.rst for initial setup
- Increased CONFIG_SYS_MONITOR_LEN so that the SPL malloc pool does not
get overwritten during copying of the u-boot.bin payload from MMC to
DDR.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Due to a typo, "run qspi_bootcmd" and "env exists secureboot" got
concatenated instead of being separated by a semicolon.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that we have added driver model support to the TSEC driver,
convert ls1021atwr board to use it.
This depends on previous DM series for ls1021atwr:
http://patchwork.ozlabs.org/patch/561855/
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
[Vladimir] Made the following changes:
- Added 'status = "disabled";' for all Ethernet ports in ls1021a.dtsi
- Fixed the confusion between the SGMII/TBI PCS for enet0 and enet1 -
a mistake ported over from Linux. Each SGMII PCS lies on the private
MDIO bus of the interface (and the RGMII enet2 has no SGMII PCS).
- Added CONFIG_DM_ETH to all ls1021atwr_* defconfigs
- Completely removed non-DM_ETH support from ls1021atwr
- Changed "compatible" string from "fsl,tsec-mdio" to "fsl,etsec2-mdio"
and from "fsl,tsec" to "fsl,etsec2" to match Linux
By convention, the eTSEC MDIO controller nodes are defined in DT at
0x2d24000 and 0x2d50000, but actually U-Boot does not touch the
interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM,
MDIO_EMAPM).
That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM,
MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at
the 0x520 offset.
So shift the DT-defined register map by the offset of MDIO_MIIMCFG when
mapping the MDIO bus registers.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
LS1028A ethernet interfaces work with at least 8 BDs, set number of buffers
to match that.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A few device-tree fixes
Binman support for extracting files from an image
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl04t50RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYGPwgAlK9Jw/UoLuag8I1rd6nS8U/EYFP4VRrS
ND5Vpe+3WxuMZvrTZyeg1oOkC6UwCJZJMJPFDN2j+VD8LzUYHymTfBykJZLq11Ks
wAieldpK75ZqKcafHP8TI3L5a2fjTj20Rgg9R3IXjy8pPp9sdtqr/GiupaEY3AJf
Y8SQrL7NRZBKxfaRZZAp2MzbzjyUDwmrgntx/xd0Tr/WwZlOf+dojyAdzKP4udfF
9JcEDi4UOyF/9YBzaSfhYO5h38ZdFan+oXpeXDwjWK5w5YV9uheXLChzloF3d9T0
CRPGfFcyl1EowDO1KB3L73HROAURzEJ8gn76IEqHraHm6dqdmU372g==
=9x0F
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-24jul19-take3' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
Minor driver-model fixes and tweaks
A few device-tree fixes
Binman support for extracting files from an image
The uclass_next_device() routine continues a previously started device
iteration. Change the description that is copied from
uclass_first_device().
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Simon Glass <sjg@chromium.org>
The comments of dev_read_name() wrongly describe "node" as its
parameter.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Starting libvirt v5.3.0 with QEMU 4.0.0 use of PCI is automatic
and thus storage is connected via PCI, which is not visible to
U-Boot out-of-the-box.
Refactor to do "pci enum" followed by "virtio scan" to see PCI
connected storage, and allow bootloader to load kernel and
initramfs images.
Tested with Fedora/RISCV using releases: libvirt 5.4.0 & 5.5.0,
QEMU 4.0.0 and U-Boot 2019.07 RC4.
Signed-off-by: David Abdurachmanov <david.abdurachmanov@sifive.com>
The rproc uclass driver can either be built with SPL_REMOTEPROC
or REMOTEPROC, but the function prototypes in remoteproc.h are
defined only when CONFIG_REMOTEPROC is defined. This can cause
build issues in SPL if CONFIG_REMOTEPROC is not selected.
Fix this by replacing the existing precompiler macro usage with
CONFIG_IS_ENABLED.
Fixes: ddf56bc7e3 ("drivers: Introduce a simplified remoteproc framework")
Signed-off-by: Suman Anna <s-anna@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for A/B boot process on AM57xx based boards:
1. Define 'slot_suffix' variable (using 'ab_select' command)
2. Extend 'emmc_android_boot' boot command (add commands for A/B boot
process)
'ab_select' command is used to decide which slot should be used for
booting up. A/B metadata resides in 'misc' partition.
To activate the A/B boot process, the following config options must be
set:
CONFIG_ANDROID_AB=y
CONFIG_CMD_AB_SELECT=y
For successful A/B boot, the corresponding A/B infrastructure must be
involved on Android side [1] (including mounting system as root), and
disk must be partitioned accordingly.
When A/B boot is enabled, there are some known limitations currently
exist (not related to A/B patches, need to be implemented later):
1. The 'Verified Boot' sequence is not supported
2. dev path to system partition (system_a or system_b) is passed via
'bootargs' as 'root=' argument like 'root=/dev/mmcblk1p12', but
further we'll need to rework it with respect to dm-verity
requirements [2]
In case when A/B partitions are not present in system (and A/B boot is
enabled), boot up process will be terminated and next message will be
shown:
"boot_a(b) partition not found"
[1] https://source.android.com/devices/tech/ota/ab
[2] https://source.android.com/devices/tech/ota/ab/ab_implement#kernel
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch determines the A/B-specific bootloader message structure
that is the basis for implementation of recovery and A/B update
functions. A/B metadata is stored in this structure and used to decide
which slot should we use to boot the device. Also some basic functions
for A/B metadata manipulation are implemented (like slot selection).
The patch was extracted from commits [1], [2] with some coding style
fixes.
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729878/2
[2] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch adds part_get_info_by_dev_and_name_or_num() function which
allows us to get partition info from its number or name. Partition of
interest is specified by string like "device_num:partition_number" or
"device_num#partition_name".
The patch was extracted from [1].
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
-----BEGIN PGP SIGNATURE-----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=aj4j
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1 (2)
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
The current implementation supports only binary file load.
Add helpers to support ELF32 format (sanity check, and load).
Note that since an ELF32 image is built for the remote processor, the
load function uses the device_to_virt ops to translate the addresses.
Implement a basic translation for sandbox_testproc.
Add related tests. Test result:
=> ut dm remoteproc_elf
Test: dm_test_remoteproc_elf: remoteproc.c
Test: dm_test_remoteproc_elf: remoteproc.c (flat tree)
Failures: 0
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Add the following functions to translate DMA address to CPU address:
- dev_translate_dma_address()
- ofnode_translate_dma_address()
- of_translate_dma_address()
- fdt_translate_dma_address()
These functions work the same way as xxx_translate_address(), with the
difference that the translation relies on the "dma-ranges" property
instead of the "ranges" property.
Add related test. Test report:
=> ut dm fdt_translation
Test: dm_test_fdt_translation: test-fdt.c
Test: dm_test_fdt_translation: test-fdt.c (flat tree)
Failures: 0
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
- rk3399 lpddr4 support
- rk3399-rock960 board support improvement
- Eliminate pyelftools dependency by make_fit_atf.py
- clean up rockchip dts to use -u-boot.dtsi
- use ARM arch/generic timer instead of rk_timer
- clean up Kconfig options for board support
SPL/TPL share the same secure_timer_init(), update to use
one copy source code and update to use CONFIG_ROCKCHIP_STIMER_BASE
as base address and rename to function name to rockchip_stimer_init().
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track the boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We prefer to use ARM arch timer instead of rockchip timer, so that
we are using the same timer for SPL, U-Boot and Kernel, which will
make things simple and easy to track to boot time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>