Allow to record the console output before before U-Boot
has a console ready.
This patch allows to test the console output in sandbox test
based on console record.
It is possible because GD_FLG_RECORD and GD_FLG_SERIAL_READY
are 2 independent flags.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reorder test on gd value and remove the duplicated test (!gd)
in putc and puts function.
This patch is a preliminary step for rework of this function.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the console puts functions to output the traces before
the log initialization (when CONFIG_LOG is not activated).
This patch allows to display the first U-Boot traces
(with macro debug) when CONFIG_DEBUG_UART is activated
and not only drop them.
For example for traces in board_f.c requested by the macro debug,
when LOG_DEBUG is defined and CONFIG_LOG is activated.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Update _log function to drop any traces when log is yet initialized:
vsnprintf is no more executed in this case.
This patch allows to reduce the cost for the dropped early debug trace.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
fit_check_format() must check that the buffer contains a flattened device
tree before calling any device tree library functions.
Failure to do may cause segmentation faults.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- DM support for OMAP PWM backlight
- USB host mode support for AM654
- Minor SPI fixes
- Add support k2g ice board with 1GHz silicon
- Fix GTC programming for K3 devices
The __of_translate_address routine translates an address from the
device tree into a CPU physical address. A note in the description of
the routine explains that the crossing of any level with
since inherited from IBM. This does not happen for Texas Instruments, or
at least for the beaglebone device tree. Without this patch, in fact,
the translation into physical addresses of the registers contained in the
am33xx-clocks.dtsi nodes would not be possible. They all have a parent
with #size-cells = <0>.
The CONFIG_OF_TRANSLATE_ZERO_SIZE_CELLS symbol makes translation
possible even in the case of crossing levels with #size-cells = <0>.
The patch acts conservatively on address translation, except for
removing a check within the of_translate_one function in the
drivers/core/of_addr.c file:
+
ranges = of_get_property(parent, rprop, &rlen);
- if (ranges == NULL && !of_empty_ranges_quirk(parent)) {
- debug("no ranges; cannot translate\n");
- return 1;
- }
if (ranges == NULL || rlen == 0) {
offset = of_read_number(addr, na);
memset(addr, 0, pna * 4);
debug("empty ranges; 1:1 translation\n");
There are two reasons:
1 The function of_empty_ranges_quirk always returns false, invalidating
the following if statement in case of null ranges. Therefore one of
the two checks is useless.
2 The implementation of the of_translate_one function found in the
common/fdt_support.c file has removed this check while keeping the one
about the 1:1 translation.
The patch adds a test and modifies a check for the correctness of an
address in the case of enabling translation also for zero size cells.
The added test checks translations of addresses generated by nodes of
a device tree similar to those you can find in the files am33xx.dtsi
and am33xx-clocks.dtsi for which the patch was created.
The patch was also tested on a beaglebone black board. The addresses
generated for the registers of the loaded drivers are those specified
by the AM335x reference manual.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
So far we used the separate mksunxiboot tool for generating a bootable
image for Allwinner SPLs, probably just for historical reasons.
Use the mkimage framework to generate a so called eGON image the
Allwinner BROM expects.
The new image type is called "sunxi_egon", to differentiate it
from the (still to be implemented) secure boot TOC0 image.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
-----BEGIN PGP SIGNATURE-----
iFsEABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX/ROlgAKCRDKSWXLKUoM
IRC5AIkBzg4Sz8fQgdCiOK89k7tdFKMAnA9SYhgm4TSCzffZCJwnm78QoGAC
=4FnY
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.04' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.04
arm64:
- DT updates
microblaze:
- Add support for NOR device support
spi:
- Fix unaligned data write issue
nand:
- Minor code change
xilinx:
- Fru fix in limit calculation
- Fill git repo link for all Xilinx boards
video:
- Add support for seps525 spi display
tools:
- Minor Vitis file support
cmd/common
- Minor code indentation fixes
serial:
- Uartlite debug uart initialization fix
This uses up space in the SPL binary but it always starts as zero. Also
some boards cannot support data in TPL (e.g. Intel Apollo Lake).
Use malloc() to allocate this structure instead, by moving the init a
little later, after malloc() is inited. Make this function optional since
it pulls in malloc().
This reduces the TPL binary size on coral by about 64 bytes
Signed-off-by: Simon Glass <sjg@chromium.org>
Support reusing board_fit_config_name_match() to automatically
select a sensible default configuration for booting fitImages
using 'bootm'.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Replace most #ifdef checks for USE_HOSTCC and CONFIG_*
with normal if instructions.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Check for negative return value of fdt_noffset from calling
boot_get_fdt_fit().
Signed-off-by: Hongwei Zhang <hongweiz@ami.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).
Rename some of the latter variables to end with 'plat' for consistency.
Signed-off-by: Simon Glass <sjg@chromium.org>
This construct is quite long-winded. In earlier days it made some sense
since auto-allocation was a strange concept. But with driver model now
used pretty universally, we can shorten this to 'auto'. This reduces
verbosity and makes it easier to read.
Coincidentally it also ensures that every declaration is on one line,
thus making dtoc's job easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fit images were loaded to a buffer provided by spl_get_load_buffer().
This may work when the FIT image is small and fits between the start
of DRAM and SYS_TEXT_BASE.
One problem with this approach is that the location of the buffer may
be manipulated by changing the 'size' field of the FIT. A maliciously
crafted FIT image could place the buffer over executable code and be
able to take control of SPL. This is unacceptable for secure boot of
signed FIT images.
Another problem is with larger FIT images, usually containing one or
more linux kernels. In such cases the buffer be be large enough so as
to start before DRAM (Figure I). Trying to load an image in this case
has undefined behavior.
For example, on stm32mp1, the MMC controller hits a RX overrun error,
and aborts loading.
_________________
| FIT Image |
| |
/===================\ /=====================\
|| DRAM || | DRAM |
|| || | |
||_________________|| SYS_TEXT_BASE | ___________________ |
| | || FIT Image ||
| | || ||
| _________________ | SYS_SPL_MALLOC_START || _________________ ||
|| malloc() data || ||| malloc() data |||
||_________________|| |||_________________|||
| | ||___________________||
| | | |
Figure I Figure II
One possibility that was analyzed was to remove the negative offset,
such that the buffer starts at SYS_TEXT_BASE. This is not a proper
solution because on a number of platforms, the malloc buffer() is
placed at a fixed address, usually after SYS_TEXT_BASE. A large
enough FIT image could cause the malloc()'d data to be overwritten
(Figure II) when loading.
/======================\
| DRAM |
| |
| | CONFIG_SYS_TEXT_BASE
| |
| |
| ____________________ | CONFIG_SYS_SPL_MALLOC_START
|| malloc() data ||
|| ||
|| __________________ ||
||| FIT Image |||
||| |||
||| |||
Figure III
The solution proposed here is to replace the ad-hoc heuristics of
spl_get_load_buffer() with malloc(). This provides two advantages:
* Bounds checking of the buffer region
* Guarantees the buffer does not conflict with other memory
The first problem is solved by constraining the buffer such that it
will not overlap currently executing code. This eliminates the chance
of a malicious FIT being able to replace the executing SPL code prior
to signature checking.
The second problem is solved in conjunction with increasing
CONFIG_SYS_SPL_MALLOC_SIZE. Since the SPL malloc() region is
carefully crafted on a per-platform basis, the chances of memory
conflicts are virtually eliminated.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
In some cases it is necessary to pass parameters to Linux so that it will
boot correctly. For example, the rootdev parameter is often used to
specify the root device. However the root device may change depending on
whence U-Boot loads the kernel. At present it is necessary to build up
the command line by adding device strings to it one by one.
It is often more convenient to provide a template for bootargs, with
U-Boot doing the substitution from other environment variables.
Add a way to substitute strings in the bootargs variable. This allows
things like "rootdev=${rootdev}" to be used in bootargs, with the
${rootdev} substitution providing the UUID of the root device.
For example, to substitute the GUID of the kernel partition:
setenv bootargs "console=/dev/ttyS0 rootdev=${uuid}/PARTNROFF=1
kern_guid=${uuid}"
part uuid mmc 2:2 uuid
bootm
This is particularly useful when the command line from another place. For
example, Chrome OS stores the command line next to the kernel itself. It
depends on the kernel version being used as well as the hardware features,
so it is extremely difficult to devise a U-Boot script that works on all
boards and kernel versions. With this feature, the command line can be
read from disk and used directly, with a few substitutions set up.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present cli_simple_process_macros() requires that the caller provide
an output buffer that is exactly CONFIG_SYS_CBSIZE bytes in length. This
makes sense since it is designed to be used from the command line. But we
also want to use it for bootargs substitution.
Update the function to allow the caller to specify the buffer size. Also
return an error if the buffer is exhausted. The caller can ignore that if
preferred.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we only support updating the 'bootargs' environment
variable. Add another function to update a buffer instead. This will
allow zimage to use this feature.
Also add a lot more tests to cover various cases.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present only one transformation is supported: making the Linux console
silent. To prepare for adding more, convert the boolean parameter into a
flag value.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present bootm_process_cmdline_env() reads the 'bootargs' variable and
then writes it back afterwards. This is painful for tests, which would
rather use a simple buffer.
It is also useful for zimage to use a buffer, since it does not actually
put the Linux command line in the bootargs variable.
Refactor the existing code into two pieces. One handles reading and
writing the environment variable, as well as allocating a buffer for use
by the rest of the code, which now operates on a buffer.
Signed-off-by: Simon Glass <sjg@chromium.org>
Use the size (including terminator) for in this function, rather than
the length. This is arguably easier to follow, with the coming
refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function will soon do more than just handle the 'silent linux'
feature. As a first step, update it to take a boolean parameter,
indicating whether or not the processing is required.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to add more processing to this function. Before doing so, rename
it to bootm_process_cmdline_env(), which is more generic.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this function fails silently on error. Update it to produce
an error code. Report this error to the user and abort the boot, since it
likely will prevent a successful start.
No tests are added at this stage, since additional refactoring is taking
place in subsequent patches.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function currently has no tests. Export it so that we can implement
a simple test on sandbox. Use IS_ENABLED() to remove the unused code,
instead #ifdef.
Signed-off-by: Simon Glass <sjg@chromium.org>
bl2_to_bl31_params_mem is just an implementation detail of the SPL ATF
support and is not needed anywhere else. Move it from the header to the
actual module.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Move the actual implementation of the bl2_plat_get_bl31_params() to its
own function. The weak function will just call the default
implementation. This has the advantage that board code can still call
the original implementation if it just want to modify minor things.
Signed-off-by: Michael Walle <michael@walle.cc>
There is no need to have the storage available globally. This is also a
preparation for LOAD_IMAGE_V2 support. That will introduce a similar
generator function which also has its own storage.
Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Capsule data can be loaded into the system either via UpdateCapsule
runtime service or files on a file system (of boot device).
The latter case is called "capsules on disk", and actual updates will
take place at the next boot time.
In this commit, we will support capsule on disk mechanism.
Please note that U-Boot itself has no notion of "boot device" and
all the capsule files to be executed will be detected only if they
are located in a specific directory, \EFI\UpdateCapsule, on a device
that is identified as a boot device by "BootXXXX" variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Since update_flash() is used only in update_tftp(), it should be
guarded with appropriate config options.
After the commit 3149e524fc, common/update.c will be built under
either CONFIG_UDATE_TFTP, CONFIG_DFU_TFTP or CONFIG_UPDATE_FIT.
Since CONFIG_UPDATE_FIT, hence fit_update(), doesn't rely on
update_flash(), the compiler may cause an "unused" warning if
CONFIG_UPDATE_FIT=y and CONFIG_UPDATE_TFTP=n and CONFIG_DFU_TFTP=n.
This is, for example, the case for sandbox defconfig where
EFI_CAPSULE_FIRMWARE_FIT is enabled for test purpose.
Fixes: 3149e524fc ("common: update: add a generic interface for FIT
image")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Since update_flash() is used only in update_tftp(), it should be
guarded with appropriate config options.
After the commit 3149e524fc, common/update.c will be built under
either CONFIG_UDATE_TFTP, CONFIG_DFU_TFTP or CONFIG_UPDATE_FIT.
Since CONFIG_UPDATE_FIT, hence fit_update(), doesn't rely on
update_flash(), the compiler may cause an "unused" warning if
CONFIG_UPDATE_FIT=y and CONFIG_UPDATE_TFTP=n and CONFIG_DFU_TFTP=n.
This is, for example, the case for sandbox defconfig where
EFI_CAPSULE_FIRMWARE_FIT is enabled for test purpose.
Fixes: 3149e524fc ("common: update: add a generic interface for FIT
image")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This commit add the support of signature check for config node
in spl/tpl when the function spl_load_simple_fit is used.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Move CONFIG_SYS_PROMPT_HUSH_PS2 in Kconfig, depending
on CONFIG_HUSH_PARSER, and remove the default value defined
in cli_hush.c under __U_BOOT__.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present these values are open-coded in a few places. Add constants so
the meaning is clear.
Also add a comment to cmd_get_data_size()
Signed-off-by: Simon Glass <sjg@chromium.org>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add logging for each part of the boot process, using a new
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
At present CONFIG_CHROMEOS is used to determine whether verified boot is
in use. The code to implement that is not in U-Boot mainline.
However, it is useful to be able to boot a Chromebook in developer mode
in U-Boot mainline without needing the verified boot code.
To allow this, use CONFIG_CHROMEOS_VBOOT to indicate that verified boot
should be used, and CONFIG_CHROMEOS to indicate that the board supports
Chrome OS. That allows us to define CONFIG_CHROMEOS on coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The series contains the following enhancements
* preparatory patches for UEFI capsule updates
* initialization of the emulated RTC using an environment variable
and a bug fix
* If DisconnectController() is called for a child controller that is the
only child of the driver, the driver must be disconnected.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAl+e1WUACgkQxIHbvCwF
GsRHhQ//X/hQiow1/3YwskyZkC89QPLE+TDeGcRHdy7W2rjfJlOBJtsI1tzvsTWw
8etgIuoh1MKebJZZQk/ZxKdWOaN3RWP7wL/9c6PHpkkML+WzyLWShf5UgLMWeo3w
a7t0LW4kfxbzmhg/f4x0Gi3qUh0SiS6T8Q5X/SlJOX091IvCmCOTkGUT6dBogm78
WnISQvgP3uApOt2s66hVVtFaH4zbXDYwDnQhhUoonRF1AfuE3jTyr39IoNsCdPOx
vEbTqNKQQnt4yIIaPJlV+KX//jtCCnyLBPrZA1tI2QPyBjADmNcau2OjlBZyJpr0
1awgSueXgBtMCAp6bHMl9p3eSKYv2f0BvPGljgKrs9dfIZk+XN0w62VuSYwRi7TU
ZEppINMisM1hC9+7jKNGn0nE9y3UldBSNThWxk8ykpWL+Btv5KeArHK4+916nadQ
a7t+6Ow7hiVI1Y/3TWaLvCi7xfqsU87QH6dx0nozgBUotuujIqa5lAeSGR9Rc6N2
PSblEGf8AA8+oGAdBhNvDncHiRLWkUoBqFsaaAk4EiaHQk60InZ9CpQdeMqHErcx
uLL9JcOCZeStcWF+vWmyU2L49O88HRHvboM7zA+gqLIUilwgKxmlOocoq+0jtA4l
Bg72F3cI7+g+aTidskEOGo2v2cj0dh32ub5CqRHLdt3PUzP6qhs=
=mCEL
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc2 (2)
The series contains the following enhancements
* preparatory patches for UEFI capsule updates
* initialization of the emulated RTC using an environment variable
and a bug fix
* If DisconnectController() is called for a child controller that is the
only child of the driver, the driver must be disconnected.
This is the complement of the existing behavior to match only messages with
a log level less than a threshold. This is primarily useful in conjunction
with LOGFF_DENY.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Without this flag, log filters can only explicitly accept messages.
Allowing denial makes it easier to filter certain subsystems. Unlike
allow-ing filters, deny-ing filters are added to the beginning of the
filter list. This should do the Right Thing most of the time, but it's
less-universal than allowing filters to be inserted anywhere. If this
becomes a problem, then perhaps log_filter_add* should take a filter number
to insert before/after.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function exposes a way to specify flags when creating a filter.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
These functions are required by "cmd: log: Add commands to manipulate
filters" and "test: Add a test for log filter-*".
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Both these arrays and their members are const. Fixes checkpatch complaint.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Errors returned should be negative.
Fixes: 45fac9fc18 ("log: Correct missing free() on error in log_add_filter()")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If this option, CONFIG_EFI_SETUP_EARLY, is enabled, the initialisation
of UEFI subsystem will be done as part of U-Boot initialisation.
Please note that this option won't be enabled explicitly by users,
instead, should be enabled implicitly by other configuration options.
Specifically, this feature will be utilised in implementing capsule-on-disk
feature.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The main purpose of this patch is to separate a generic interface for
updating firmware using DFU drivers from "auto-update" via tftp.
This function will also be used in implementing UEFI capsule update
in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
The range of an addressable pointer can go beyond 'integer'.
So change the argument type to a void pointer.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is essentially independent from tftp, and will also be
utilised in implementing UEFI capsule update in a later commit.
So just give it a more generic name.
In addition, a new configuration option, CONFIG_DFU_WRITE_ALT, was
introduced so that the file will be compiled with different options,
particularly one added in a later commit.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this option results in a number of #ifdefs due to the presence
or absence of the global_data of_root member.
Add a few macros to global_data.h to work around this. Update the code
accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
This will probe the multiplexer devices that have a "u-boot,mux-autoprobe"
property. As a consequence they will be put in their idle state.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
The log command has led to NULL dereferences if an unknown category name
name was used due to missing entries in the list of category names.
Add compile time checks for the array sizes of log_cat_name and
log_lvl_name to avoid future mishaps.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some drivers use macro pr_cont() for continuing a message sent via printk.
Hence if we want to convert printk messaging to using the logging system,
we must support continuation of log messages too.
As pr_cont() does not provide a message level we need a means of
remembering the last log level.
With the patch a pseudo log level LOGL_CONT as well as a pseudo log
category LOGC_CONT are introduced. Using these results in the application
of the same log level and category as in the previous log message.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Replace the static variable processing_msg by a field in the global data.
Make the field bool at it can only be true or false.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
The commit 9f45aeb937 ("spl: fit: implement fdt_record_loadable") which
introduced fdt_record_loadable() state there spl_fit.c is not 64bit safe.
Based on my tests on Xilinx ZynqMP zcu102 platform there shouldn't be a
problem to record these addresses in 64bit format.
The patch adds support for systems which need to load images above 4GB.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
SPL is creating fit-images DT node when loadables are recorded in selected
configuration. Entries which are created are using entry-point and
load-addr property names. But there shouldn't be a need to use non standard
properties because entry/load are standard FIT properties. But using
standard FIT properties enables option to use generic FIT functions to
descrease SPL size. Here is result for ZynqMP virt configuration:
xilinx_zynqmp_virt: spl/u-boot-spl:all -82 spl/u-boot-spl:rodata -22 spl/u-boot-spl:text -60
The patch causes change in run time fit image record.
Before:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry-point = <0x8000000>;
load-addr = <0x8000000>;
};
};
After:
fit-images {
uboot {
os = "u-boot";
type = "firmware";
size = <0xfd520>;
entry = <0x8000000>;
load = <0x8000000>;
};
};
Replacing calling fdt_getprop_u32() by fit_image_get_entry/load() also
enables support for reading entry/load properties recorded in 64bit format.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It doesn't need to consider start byte address.
If ramdisk size is 0x800000 and start address is 0x2700000, then it's
used until 0x02efffff, not 0x02f00000. But it's detected to overlapt RD
image, when kernel start address is 0x02f00000.
Because it's doing wrong calculation about rd_len.
This patch fixed wrong calculation address position when check
condition.
In addition, it needs to check one more condition about overlapping
entire area.
Fixes: commit fbde7589ce ("common: bootm: add checks to verify if ramdisk / fdtimage overlaps OS image")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Remove the default value "usb start" for CONFIG_USB_STORAGE as the USB
storage boot initialization is correctly managed by distro boot command
('usb_boot' defined in include/config_distro_bootcmd.h already include
the command 'usb start').
Fixes: 324d77998e ("Define default CONFIG_PREBOOT with right config option")
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sandbox is built with the SDL2 library with invokes the X11 library
which in turn calls getc(). But getc() in glibc is defined as
int getc(FILE *)
This does not match our definition.
int getc(void)
The sandbox crashes when called with parameter -l.
Rename our library symbol getc() to getchar().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This code is intended do prevent one from setting a shell variable abc
by doing
abc=123
if an environment variable named abc already exists. However, the
check is broken, since the env_get is done before the split on =, so
we look up whether an environment variable "abc=123" exists, which is
obviously never the case.
One could move the code to below the split on =, but instead, just
remove it, saving a little .text: The check has never worked as
intended (it goes all the way back to the initial git commit), and it
would anyway not guard against one first setting the shell variable,
then doing 'env set abc xyz'.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
add back again special case: -2
autoboot with no delay and no check for abort
as described in Kconfig option, see common/Kconfig
help text for option BOOTDELAY.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Fix some comments about functions.
Move genimg_get_comp_name() above genimg_get_short_name() because
genimg_get_comp_name() is related to get_table_entry_name().
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a generic function which can check whether a category has an
entry ID.
Signed-off-by: Naoki Hayama <naoki.hayama@lineo.co.jp>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_{SPL,TPL}_SIZE_LIMIT are defined as hex (SPL_SIZE_LIMIT was
converted in b51882d0 ("spl: Convert CONFIG_SPL_SIZE_LIMIT to hex"), but
there are still places that reference integer values. Change those to hex
as well. Also, update the Makefile to check for 0x0 instead of 0.
This also fixes the following build error when CONFIG_SPL_SIZE_LIMIT
is set by menuconfig to 0x0:
...
spl/u-boot-spl.bin exceeds file size limit:
limit: 0 bytes
actual: 0x80f0 bytes
excess: 0x80f0 bytes
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is much easier to read the bloblist addresses if it starts on a 4KB
boundary. Update it to align it accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards, specifically 64-bit Allwinner boards (sun50i), are
extremely limited on SPL size. One strategy that was used to make space
was to remove the FIT "os" property parsing code, because it uses a
rather large lookup table.
However, this forces the legacy FIT parsing code path, which requires
the "firmware" entry in the FIT to reference the U-Boot binary, even if
U-Boot is not the next binary in the boot sequence (for example, on
sun50i boards, ATF is run first).
This prevents the same FIT image from being used with a SPL with
CONFIG_SPL_FIT_IMAGE_TINY=n and CONFIG_SPL_ATF=y, because the boot
method selection code looks at `spl_image.os`, which is only set from
the "firmware" entry's "os" property.
To be able to use CONFIG_SPL_ATF=y, the "firmware" entry in the FIT
must be ATF, and U-Boot must be a loadable. For this to work, we need to
parse the "os" property just enough to tell U-Boot from other images, so
we can find it in the loadables list to append the FDT, and so we don't
try to append the FDT to ATF (which could clobber adjacent firmware).
So add the minimal code necessary to distinguish U-Boot/non-U-Boot
loadables with CONFIG_SPL_FIT_IMAGE_TINY=y. This adds about 300 bytes,
much less than the 7400 bytes added by CONFIG_SPL_FIT_IMAGE_TINY=n.
Acked-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit eb39d8ba5f.
The commit breaks booting of fitImage by SPL, the system simply hangs.
This is because on arm32, the fitImage and all of its content can be
aligned to 4 bytes and U-Boot expects just that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Reuben Dowle <reuben.dowle@4rf.com>
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Marek Vasut <marex@denx.de>
To simplify configuration and keep synchronized the PStore/Ramoops between
U-Boot and the Linux kernel, this commit dynamically adds the Ramoops
parameters defined in the U-Boot session to the Device Tree.
Signed-off-by: Frédéric Danis <frederic.danis@collabora.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
This commit add the support in u-boot to read the IV
in the FIT image instead of u-boot device tree.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Currently FIT image must be signed by all required conf keys. This means
Verified Boot fails if there is a signature verification failure
using any required key in U-Boot DTB.
This patch introduces a new policy in DTB that can be set to any required
conf key. This means if verified boot passes with one of the required
keys, U-Boot will continue the OS hand off.
There were prior attempts to address this:
https://lists.denx.de/pipermail/u-boot/2019-April/366047.html
The above patch was failing "make tests".
https://lists.denx.de/pipermail/u-boot/2020-January/396629.html
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the previous patch, net_init now exposes some errors, so check for
them.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver interferes with other sandbox tests since it causes log output
to be interspersed with "No ethernet found." messages. Disable this driver
by default.
Enable it for the syslog tests so that they still pass.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present all log devices are enabled by default. Add a function to allow
devices to be disabled or enabled at runtime.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there is no way to disable a log driver. But the syslog driver
causes (attempted) network traffic in sandbox every time a log message
is printed, which is often.
Add a flag to enable a log driver. Adjust struct log_device to use a short
for next_filter_num so that no more memory is used for devices. Also fix
a missing line in the struct log_driver comment while here.
To maintain compatibility, enable it for all drivers for now.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_LOG enabled, putting LOG_DEBUG at the top of a file
(before log.h inclusion) causes _log() to be executed for every log()
call, regardless of the build- or run-time logging level.
However there is no guarantee that the log record will actually be
displayed. If the current log level is lower than LOGL_DEBUG then it will
not be.
Add a way to signal that the log record should always be displayed and
update log_passes_filters() to handle this.
With the new behaviour, log_debug() will always log if LOG_DEBUG is
enabled.
Move log_test_syslog_nodebug() into its own file since it cannot be made
to work where it is, with LOG_DEBUG defined.
Signed-off-by: Simon Glass <sjg@chromium.org>
This relates to booting since it is the default devicetree provided to
Linux. Move it under the 'boot options' menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are a number of miscellaneous boot images at the top level of the
kconfig menu. Move these into the 'boot options' menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present the autoboot options are in cmd/Kconfig but they don't really
relate to commands. They relate to booting, so move this menu under the
boot menu.
Signed-off-by: Simon Glass <sjg@chromium.org>
Most of the boot options are in common/Kconfig but that file is already
extremely large. Create a new Kconfig.boot to hold the boot options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some blobs need a larger alignment than the default. For example, ACPI
tables often start at a 4KB boundary. Add support for this.
Update the size of the test blob to allow these larger records.
Signed-off-by: Simon Glass <sjg@chromium.org>
The intention which bloblists is that each blob's data is aligned in
memory. At present it is only the headers that are aligned.
Update the code to correct this and add a little more documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is helpful to be able to see basic statistics about the bloblist and
also to list its contents. Add a 'bloblist' command to handle this.
Put the display functions in the bloblist modules rather than in the
command code itself. That allows showing a list from SPL, where commands
are not available.
Also make bloblist_first/next_blob() static as they are not used outside
this file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Move call to optee_copy_fdt_nodes() introduced by commit 6ccb05eae0
before generic changes in kernel FDT so that platform specific changes
are not overridden by the changes made by this function.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The 44758771ee commit removes CONFIG_PREBOOT but actually sets the USE_PREBOOT
Kconfig option which isn't CONFIG_PREBOOT and is also a bool option which means
we regress because 'usb start' isn't run when expected, it should also be run
for devices that have USB storage because keyboards aren't the only thing we
might need the USB bus for.
Fixes: 44758771ee ("arm: move CONFIG_PREBOOT="usb start" to KConfig")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jonas Smedegaard <dr@jones.dk>
Cc: Neil Armstrong <narmstrong@baylibre.com>
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX2x4MgAKCRDKSWXLKUoM
IZQtAJ9HpNwG5q3nHt9WedzLCTkr3YoLAACeJJ0Wlpp5p5xPzuPmnoo/Vi4MtNQ=
=yxRo
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2021.01
arm64:
- Support for bigger U-Boot images compiled with PIE
microblaze:
- Extend support for LE/BE systems
zynqmp:
- Refactor silicon ID detection code with using firmware interface
- Add support for saving variables based on bootmode
zynqmp-r5:
- Fix MPU mapping and defconfig setting.
xilinx:
- Minor driver changes: names alignment
- Enable UBIFS
- Minor DT and macros fixes
- Fix boot with appended DT
- Fix distro boot
cmd:
- pxe: Add fixing for platforms with manual relocation support
clk:
- fixed_rate: Add DM flag to support early boot on r5
fpga:
- zynqmppl: Use only firmware interface and enable SPL build
serial:
- uartlite: Enable for ARM systems and support endians
mmc:
- zynq: Fix indentation
net:
- gem: Support for multiple phys
- emac: Fix 64bit support and enable it for arm64
kconfig:
- Setup default values for Xilinx platforms
- Fix dependecies for Xilinx drivers
- Source board Kconfig only when platform is enabled
- Fix FPGA Kconfig entry with SPL
- Change some defconfig values
bindings:
- Add binding doc for vsc8531
ATF support was all the time based on FIT image support but this dependency
is not recorded anywhere.
For !SPL_FIT && SPL_ATF there is compilation error:
common/spl/spl.c: In function 'board_init_r':
common/spl/spl.c:689:26: error: 'struct spl_image_info' has no member named 'fdt_addr'
689 | spl_fixup_fdt(spl_image.fdt_addr);
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile
and zynqmp.c to simplify if/endif logic in zynqmp.c.
This change is mostly done to be able to use CONFIG_IS_ENABLED macro and
obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync.
And removing one line from Topic Miami boards which is not needed because
symbol is not enabled via Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When a message is written by a log driver (e.g. via the network stack) this
may result in the generation of further messages. We cannot allow these
additional messages to be emitted as this might result in an infinite
recursion.
Up to now only the syslog driver was safeguarded. We should safeguard all
log drivers instead.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
In bootm_load_os() the OS image is decompressed. In later stages of the
boot process we need the decompressed size of the image.
Update images->os.image_len after decompression.
Passing the correct size is necessary if we want to check loaded EFI
binararies for file truncation by comparing the loaded size to the header
field SizeOfImage.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Kconfig provides several config options for setting up default variables
but these are unused when variables are passed to U-Boot via file.
That's why cover this dependency in Kconfig.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The environment variable loadaddr is in the virtual address space of the
sandbox. To get the actual memory address where the FIT image has been
loaded we have to convert this address according to the memory mapping of
the sandbox.
Equally the addresses in the *.its file have to be converted when used in
the dfu_ram driver.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
%s/parameteres/parameters/g
Even if a line exceeds 80 characters we should not split output strings
to make debugging easier.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When board_get_usable_ram_top() limits gd->ram_top, env_get_bootm_size()
must not exceed that limit. Otherwise, boot_relocate_fdt() might put fdt
out of the allowed RAM range.
The similar commit 8ce1f10cf2 ("ARM: bootm: take into account
gd->ram_top") exposed this bug.
This fixes boot on Armada 8040 based Clearfog GT-8K where ram_top is set
to 0x80000000 (2GB), but bi_dram[0].size might be up to 0xc0000000
(3GB). Note the relocated fdt address (0xbfff4000) in the console output
listed below:
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
62 bytes read in 21 ms (2 KiB/s)
1: linux
Retrieving file: /extlinux/Image
13740544 bytes read in 1266 ms (10.4 MiB/s)
Retrieving file: /extlinux/armada-8040-clearfog-gt-8k.dtb
33368 bytes read in 31 ms (1 MiB/s)
Booting using the fdt blob at 0x4f00000
Loading Device Tree to 00000000bfff4000, end 00000000bffff257 ... "Synchronous Abort" handler, esr 0x96000045
elr: 000000000006e1cc lr : 0000000000068fd8 (reloc)
elr: 000000007ffa91cc lr : 000000007ffa3fd8
x0 : ffffffffffffffff x1 : 00000000bfffc258
x2 : 0000000000000000 x3 : ffffffffffff7da7
x4 : 0000000004f08258 x5 : 00000000bfff4000
x6 : 00000000bfff4000 x7 : 000000000000000f
x8 : 000000007fb23bf8 x9 : 0000000000000008
x10: 00000000bffff257 x11: 00000000bffff257
x12: 0000000000000000 x13: fffffffffffff000
x14: 00000000bfff4000 x15: 0000000000000021
x16: 000000007ff7bc38 x17: 0000000000000000
x18: 000000007fb2add0 x19: 00000000bfff4000
x20: 0000000004f00000 x21: 000000000000b258
x22: 0000000058820000 x23: 0000000000000010
x24: 000000007ffe3c40 x25: 000000007fb23cb8
x26: 00000000c0000000 x27: 0000000000000000
x28: 000000007fc3fd50 x29: 000000007fb23bd0
Code: 54000061 aa0603e0 d65f03c0 38606882 (38206822)
Resetting CPU ...
Thanks to Patrice CHOTARD who directed me to the right way.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Remove the bi_memstart / bi_memsize assignment in setup_bdinfo() and
make sure, that bd_dram[] is always configured in the weak default
implementation of dram_init_banksize(), when CONFIG_SYS_SDRAM_BASE is
not set.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Use only gd->ram_base/_size in env_get_bootm_size() instead of bi_dram[]
in some cases and bi_memstart in others.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since commit 86cf1c8285 ("configs: Migrate CONFIG_NR_DRAM_BANKS") &
commit 999a772d9f ("Kconfig: Migrate CONFIG_NR_DRAM_BANKS"),
CONFIG_NR_DRAM_BANKS is always defined with a value (4 is default).
It makes no sense to still carry code that is guarded with
"#ifndef CONFIG_NR_DRAM_BANKS" (and similar). This patch removes
all these unreferenced code paths.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
AVB only uses CONFIG_FASTBOOT_BUF_ADDR from fastboot for memory.
This memory is used for assigning temporary buffers.
This can be assigned a new variable and used as CONFIG_AVB_BUF_ADDR.
This is to support future boards that support AVB but dont support
USB and therefore dont support FASTBOOT.
Signed-off-by: Usama Arif <usama.arif@arm.com>
Cc: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
[trini: Change defaults]
Signed-off-by: Tom Rini <trini@konsulko.com>
binman fixes for portage
various minor fixes
'bind' command improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl9BbZcRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZZiQf/UVsriftmxdDz3Lvbz7Jw6UCBXbeM3UN8
KgRxVll3kurZeu8bIcjAPY4YRrbWRqSXmZTXpZWgbyZzHLM4RnkamY3KF3DoxPjc
cbskd/fr4nPjSZVFrkzrvD+D5bhm+VrMtf861AkbAqqpG+Q1FmWHgApqOL1fXn3s
2VoMxRz8Cn9KkSDmxaCtJnLX77GVYYdfgii7RuNWGDqr3eBWrzflV38VbPHLplEg
VLqaLBe3G4zVwElA9Nc2hXpZB84KZEETHcBnmCzNkrSYTN2ofvSeZrWbtRztQFhz
yKur1y7jFsryRkMfxBzgldsKFRNnPT9vr+0qGtrztHjCmvhDkx1YMg==
=iDRJ
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-22aug20' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
replace devfdt_get_addr_ptr() with dev_read_addr_ptr()
binman fixes for portage
various minor fixes
'bind' command improvements
Now that this is in Kconfig we can move the logic at the top of the file
to Kconfig, and use if() instead of #if. Update the file with these
changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Since commit 69153988a6 ("i2c: Finish dropping use of CONFIG_I2C_HARD")
init_func_i2c is wrapped only by "#if defined(CONFIG_SYS_I2C)". Because
of this, the second ifdef within becomes pointless:
#if defined(CONFIG_SYS_I2C)
static int init_func_i2c(void)
<snip>
#ifdef CONFIG_SYS_I2C
...
#else
...
#endif
<snip>
}
#endif
Remove the dead #else preprocessor code.
Fixes: 69153988a6 ("i2c: Finish dropping use of CONFIG_I2C_HARD")
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Add initial infrastructure for Xen para-virtualized block device.
This includes compile-time configuration and the skeleton for
the future driver implementation.
Add new class UCLASS_PVBLOCK which is going to be a parent for
virtual block devices.
Add new interface type IF_TYPE_PVBLOCK.
Implement basic driver setup by reading XenStore configuration.
Signed-off-by: Andrii Anisov <andrii_anisov@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Port hypervisor related code from Mini-OS. This is referencing the code
of Mini-OS from [1] by Huang Shijie and Volodymyr Babchuk which is for
ARM64.
Update essential arch code to support required bit operations, memory
barriers etc.
Copyright for the bits ported belong to at least the following authors,
please see related files for details:
Copyright (c) 2002-2003, K A Fraser
Copyright (c) 2005, Grzegorz Milos, gm281@cam.ac.uk,Intel Research Cambridge
Copyright (c) 2014, Karim Allah Ahmed <karim.allah.ahmed@gmail.com>
[1] - https://github.com/zyzii/mini-os.git
Signed-off-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Signed-off-by: Anastasiia Lukianenko <anastasiia_lukianenko@epam.com>
[trini: Drop wmb() from musb-net/linux-compat.h now]
Signed-off-by: Tom Rini <trini@konsulko.com>
There may be a chance that board specific fix_fdt() will change the
size of FDT blob so it's safe to call reserve_fdt() after fix_fdt()
otherwise global data (gd) will overwrite with FDT blob values.
Fixes: a8492e25ac ("riscv: Expand the DT size before copy reserved memory node")
Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Atish Patra <atish.patra@wdc.com>
usb_init() may be called multiple times for fetching multiple images
from SPL. Skip reinitializing USB if its already been done
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Create a new API spl_usb_load() that takes the filename as a parameter
instead of taking the default U-boot PAYLOAD_NAME
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add support for SquashFS filesystem. Right now, it does not support
compression but support for zlib will be added in a follow-up commit.
Signed-off-by: Joao Marcos Costa <joaomarcos.costa@bootlin.com>
On boards without console recording these function are currently missing.
It is more convenient for them to be present but to return dummy values.
That way if we know that a test needs recording, we can check if it is
available, and skip the test if not, while avoiding #ifdefs.
Update the header file according and adjust console_record_reset_enable()
to return an error if recording is not available.
Signed-off-by: Simon Glass <sjg@chromium.org>
blkcache_init manually relocates blkcache list pointers when
CONFIG_NEEDS_MANUAL_RELOC is enabled. However, it is called very late in
the boot sequence, which could be a problem if previous boot calls execute
blkcache operations with the non-relocated pointers. For example, mmc is
initialized earlier and might call blkcache_invalidate (in
mmc_select_hwpart()) when trying to load the environment from mmc via
env_load().
To fix this issue, move blkcache_init boot call earlier, before mmc gets
initialized.
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Extend manual relocation of block_cache list pointers to all platforms that
enable CONFIG_NEEDS_MANUAL_RELOC. Remove m68k-specific checks and provide a
single implementation that adds gd->reloc_off to the pre-relocation
pointers.
Acked-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Tested-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Eric Nelson <eric@nelint.com>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
[trini: Add guard around DECLARE_GLOBAL_DATA_PTR to avoid size growth]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now that all arch specific code was converted to setup_bdinfo, we can
remove setup_board_part1.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Factor out ppc-specific bdinfo setup from generic init sequence to
arch_setup_bdinfo in arch/powerpc/lib/bdinfo.c.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Factor out m68k-specific bdinfo setup to arch_setup_bdinfo in
arch/m68k/lib/bdinfo.c. Also, use if(IS_ENABLED()) instead of #ifdef where
possible.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Move sram related bdinfo from arch-specific setup_board_part1 to generic
code in setup_bdinfo. Also use "if (IS_ENABLED(CONFIG_SYS_HAS_SRAM))"
instead of "#ifdef CONFIG_SYS_SRAM_BASE".
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Move all assignments to gd->bd->bi_mem{start,size} to generic code in
setup_bdinfo.
Xtensa architecture is special in this regard as it defines its own
handling of gd->bd->bi_mem{start,size} fields. In order to avoid defining
a weak SDRAM function, let arch_setup_bdinfo overwrite the generic flags.
For ARC architecture, remove ARCH_EARLY_INIT_R from Kconfig since it is
not needed anymore.
Also, use gd->ram_base to populate bi_memstart to avoid an ifdef.
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Acked-by: Alexey Brodkin <abrokdin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Certain architectures (ppc, mips, sh, m68k) use setup board_part1 and
setup_board_part2 calls during pre-relocation init to populate gd->bd
boardinfo fields. This makes the generic init sequence cluttered with
arch-specific ifdefs.
In order to clean these arch-specific sequences from generic init,
introduce arch_setup_bdinfo weak initcall so that everyone can define their
own bdinfo setup routines.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Introduce setup_bdinfo initcall as a generic routine to populate bdinfo
fields.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
