Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
-VSC8662 is Dual Port 10/100/1000Base-T Phy,
100Base-FX/1000/Base-X Gigabit Ethernt Transceiver Phy.
-Its register set and features are similar to
other Vitesse Phys
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
This patch add support for the configuration of an external switch from
the 88E6xxx series from Marvell trough an MDIO link using indirect
adressing. This can be used if we do not want to use an EEPROM for the
configuration.
This driver is not generic and was not tested on other switches than the
88e6352. This is proposed as a first implementation that is somewhat
limited but works and that can be used as a basis for further
developments for this switch family.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Holger Brunck <holger.brunck@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Joe Hershberger <joe.hershberger@gmail.com>
Device driver for Zynq Gem IP.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
CC: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Add AX88772B ID together with two fixes needed to make this work.
1. The packet length check has to be adjusted, as all ASIX chips
only use 11 bits to indicate the length. AX88772B uses the other
bits to indicate unrelated things, which cause the check to fail.
This fix is based on a fix for the Linux kernel by Marek Vasut.
Linux upstream commit: bca0beb9363f8487ac902931a50eb00180a2d14a
2. AX88772B provides several bulk endpoints. Only the first
IN/OUT endpoints work in the default configuration. So stop
enumeration after we found them to avoid overwriting the
endpoint config with a non-working one.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Initial device MAC should be read while getting info about the
device, so it's wrong to only read it in asix_init().
Add a dedicated function to read the initial MAC, which is also
able to handle devices that have their initial MAC stored in
EEPROM. Call this function inasix_eth_get_info().
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
All ASIX chipsets aside from AX88172 are able to set the MAC
address on the hardware level. Add a function to expose this
ability.
To differentiate between chip types we now carry flags as driver
private data. Also while touching the asix_dongles array
constify this.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The basic device reset ensures that the device is ready to
service commands and does not need to get redone before each
network operation.
Split out the basic reset from asix_init() and instead call it
from asix_eth_get_info(), so that it only gets called once.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Avoid clutter in ueth_data. Individual drivers should not mess
with structures belonging to the core like this.
Signed-off-by: Lucas Stach <dev@lynxeye.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Check the incoming packets' source IP address... if ncip isn't set to a
broadcast address, only listen to the client at ncip.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Refresh the netconsole settings from the env before each packet instead
of only on netconsole init.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Previously u-boot would initialize the network interface for every
network operation and then shut it down again. This makes sense for
most operations where the network in not known to be needed soon after
the operation is complete. In the case of netconsole, it will use the
network for every interaction with the shell or every printf. This
means that the network is being reinitialized very often. On many
devices, this intialization is very slow.
This patch checks for consecutive netconsole actions and leaves the
ethernet hardware initialized between them. It will still behave the
same old way for all other network operations and any time another
network operation happens between netconsole operations.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Allow a board to configure a larger buffer for netconsole, but leave
the default.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
R8A7740 of rmobile has ethernet device, and this is same IP of
sh-ether. This support R8A7740 of rmobile.
Signed-off-by: Hideyuki Sano <hideyuki.sano.dn@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Apply the following questionable adjustment to silence GCC.
armada100_fec.c: In function ‘armdfec_send’:
armada100_fec.c:589:2: warning: dereferencing type-punned pointer will break strict-aliasing rules [-Wstrict-aliasing]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Support new CONFIG_OF_CONTROL option where device
probing is done based on device tree description.
Signed-off-by: Michal Simek <monstr@monstr.eu>
CC: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bryan Hundven <bryanhundven@gmail.com>
Cc: Michael Schwingen <rincewind@discworld.dascon.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: U-Boot DM <u-boot-dm@lists.denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
It is desirable to use different port numbers for sending and receiving
packets with netconsole in the case where you have more than one device
on the local subnet with netconsole enabled for broadcast. When they
use the same port for both, any output from one will look like input to
the other. This is typlically not desirable.
This patch allows the input and output ports to be specified separately
in the environment.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
The following commit introduced some warnings associated with using
pci_addr_t instead of a proper 32-bit data type.
commit af778c6d9e
Author: Andrew Sharp <andywyse6@gmail.com>
Date: Wed Aug 1 12:27:16 2012 +0000
pci: fix errant data types and corresponding access functions
On some platforms pci_addr_t is defined as a 64-bit data type so its not
proper to use with pci_{read,write}_config_dword.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
usb_hub_descriptor has to be packed as it's used for
communication with the device. Member wHubCharacteristics
violates the natural alignment rules.
Use explicit unaligned access functions for this member.
Fixes ARMv7 traping while using USB.
v2: fix typo found by Thomas Langer
v3: rebased on top of u-boot-usb/master
Signed-off-by: Lucas Stach <dev@lynxeye.de>
The "filesize" environment variable shall be read only when relevant
file is read.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Support for ext4 file system handling at DFU.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds a driver for Freescale Colfire Queued SPI bus.
Coded to work with 8 bits per transfer to use with SPI flash.
CPOL, CPHA, and CS_ACTIVE_HIGH can be configured.
Tested with MCF5270 which have 4 chip selects.
Activate by #define CONFIG_CF_QSPI in board config.
Signed-off-by: Richard Retanubun <richardretanubun@ruggedcom.com>
The MPC8308RDB Reference Manual states that no bits in the SPMODE
register are allowed to change while the enable (EN) bit is set.
This driver changes the character length bits (LEN) while the enable
(EN) bit is set. Clearing the EN bit while changing the LEN bits makes
the driver work correctly on MPC8308RDB.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
greth.c: In function ‘greth_recv’:
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘unsigned int’ [-Wformat]
greth.c:507:3: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 3 has type ‘unsigned int’ [-Wformat]
greth.c:541:6: warning: pointer targets in assignment differ in signedness [-Wpointer-sign]
greth.c: In function ‘greth_initialize’:
greth.c:623:2: warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:655:3: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
greth.c:684:2: warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 2 has type ‘struct greth_regs *’ [-Wformat]
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Daniel Hellstrom <daniel@gaisler.com>
Cc: u-boot-dm@lists.denx.de
Use the same IP revisions as in Linux in order to make the comparison more
clear.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Merge mxc_setup_config1() into board_nand_init() in order to ease the addition
of i.MX5 support in the following patches.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
mxc_nand_read_page_raw_syndrome() should reenable ECC upon exit. This fixes ECC
errors left uncorrected after a call to this function.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Use _mxc_nand_enable_hwecc() instead of duplicating its code.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the NFC IP 1.1, the 32-bit ecc_status_result value comes from 2
consecutive 16-bit registers. This patch reads all the fields of this value,
which makes a difference for 4-kiB NF pages.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patches fixes the TODO to use same register definitions in mtd mxc_nand and
nand_spl fsl nfc drivers.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This is based on Linux kernel -next:
commit 14f44abf1dafc20ba42ce8616a8fc8fbd1b3712b
Author: Brian Norris <computersforpeace@gmail.com>
Date: Fri Jul 13 09:28:24 2012 -0700
mtd: nand: allow NAND_NO_SUBPAGE_WRITE to be set from driver
The NAND_CHIPOPTIONS_MSK has limited utility and is causing real bugs. It
silently masks off at least one flag that might be set by the driver
(NAND_NO_SUBPAGE_WRITE). This breaks the GPMI NAND driver and possibly
others.
Really, as long as driver writers exercise a small amount of care with
NAND_* options, this mask is not necessary at all; it was only here to
prevent certain options from accidentally being set by the driver. But the
original thought turns out to be a bad idea occasionally. Thus, kill it.
Note, this patch fixes some major gpmi-nand breakage.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Micron NAND flash (e.g. MT29F4G08ABADAH4) BLOCK LOCK READ STATUS is not
the same as others. Instead of bit 1 being lock, it is #lock_tight.
To make the driver support either format, ignore bit 1 and use only
bit 0 and bit 2.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND_CMD_ constants for lock/unlock should be in the header
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
NAND unlock command allows an invert bit to be set to unlock all but
the selected page range.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
[scottwood@freescale.com: updated docs and added comment about invert bit]
Signed-off-by: Scott Wood <scottwood@freescale.com>
With onfi a flash is organized into one or more logical units (LUNs).
A logical unit (LUN) is the minimum unit that can independently execute
commands and report status.
Mtd does not exploit LUN, so make it see a big single flash where size is
lun_size * number_of_lun.
Without this patch MT29F8G08ADBDAH4 size is 512MiB instead of 1GiB.
Artem: split long line on 2 shorter ones.
This is commit 637957551c0ac80de8dfc7650d320c5a98c2c0c0 from Linux
Signed-off-by: Matthieu Castet <matthieu.castet@parrot.com>
Acked-by: Florian Fainelli <ffainelli@freebox.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[scottwood@freescale.com: picked from Linux into U-Boot]
Reported-by: Rafael Beims <rafael.beims@gmail.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Warning is:
xilinx_spi.c: In function 'spi_setup_slave':
xilinx_spi.c:81: warning: unused variable 'regs'
Signed-off-by: Stephan Linz <linz@li-pro.net>
CC: Michal Simek <monstr@monstr.eu>
Initialize all possible uartlites and return the first
initialized port. For static configuration is initialization
done in userial_ports array.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Acked-by: Stephan Linz <linz@li-pro.net>
Use CONFIG parameters only at one location to simplify
the code. Also create ace_readw/writew functions.
Signed-off-by: Michal Simek <monstr@monstr.eu>
With Simon Glass's include/nand.h alignment changes, some mxs builds
were generating errors. Fix is to ensure asm/cache.h is included before
linux/mtd/nand.h. Moving common.h to top of include list does that.
Signed-off-by: Tom Warren <twarren@nvidia.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
