The reference manuals for MPC8308 and MPC8309 both say that the
esdhcctl aka DMA Control Register "is implemented as SDHCCR" in the
System configuration registers. Unfortunately, that doesn't mean that
the registers are just mirrors of each other - any write to esdhcctl
is simply ignored. So to actually enable cache snooping, we
unfortunately have to add a little ifdeffery.
There is, naturally, no description of the bit fields of esdhcctl in
the MPC8309 manual, but comparing the description of esdhcctl from the
LS1021A reference manual to the description of the sdhccr in MPC8309,
one also finds that the fields are bit-reversed, so the bit to set is
0x02000000 rather than 0x00000040 - this is also what board_mmc_init()
uses in the two gdsys/mpc8308/ boards.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Yangbo Lu <yangbo.lu@nxp.com>
These functions are defined before the callers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 01298da31d ("mmc: Change mode when switching to a boot
partition"), errors in mmc_select_mode_and_width() are ignored.
The return value should be checked.
Fixes: 01298da31d ("mmc: Change mode when switching to a boot partition")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Cadence sent out an errata report to their customers of this IP.
This errata is not so severe, but the tune request should be sent
twice to avoid the potential issue.
Quote from the report:
Problem Summary
---------------
The IP6116 SD/eMMC PHY design has a timing issue on receive data path.
This issue may lead to an incorrect values of read/write pointers of
the synchronization FIFO. Such a situation can happen at the SDR104
and HS200 tuning procedure when the PHY is requested to change a phase
of sampling clock when moving to the next tuning iteration.
Workarounds
-----------
The following are valid workarounds to resolve the issue:
1. In eMMC mode, software sends tune request twice instead of once at
each iteration. This means that the clock phase is not changed on
the second request so there is no potential for clock instability.
2. In SD mode, software must not use the hardware tuning and instead
perform an almost identical procedure to eMMC, using the HRS34 Tune
Force register.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
erase_grp_size is used, when MMC_WRITE is enabled.
- error: ‘struct mmc’ has no member named ‘erase_grp_size’
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
If the host has Broken R1B, use only R1 response type.
Signed-off-by: Bharat Kumar Reddy Gooty <bharat.gooty@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Drop local dma_map_single() and dma_unmap_single() and use arch specific
common implementation
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Read generic MMC properties from device-tree. This allows to specify for
example cd-inverted property and let MMC core to properly handle such
case.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
Add Support for writing to PHY registers for J721e. There are number of
differences between the J721e 8 bit PHY, J721e 4 bit PHY and AM654 PHY.
Create a driver_data structure with an ops and flags field and use the
flags field to indicate these differences. The differences are as
follows:
1. The J721e 4 bit instance PHY does not have a DLL. Introduce a
DLL_PRESENT flag to make sure that DLL related registers are accessed
only where they are present. Also add a separate set_ios_post()
callback.
2. The J721e 8 bit instance is not muxed with anything else inside the
SoC and hence the IOMUX_ENABLE filed does not exist. Add a flag which is
used to indicate the presence of this field.
3. The register field used to select DLL frequency is 3 bit wide in
J721e as compared to 2 bits in AM65x. Add another flag that
distinguishes these fields.
4. The strobe select field is 8 bit wide as compared to 4 bit wide for
AM65x. Add yet another flag to indicate this difference. Strobe select
is used only for HS400 speed mode, support for which has not been added
in AM65x.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Get clk_xin by name instead of by index to avoid having to put clocks in
the same order in all devices.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
At present panic() is in the vsprintf.h header file. That does not seem
like an obvious choice for hang(), even though it relates to panic(). So
let's put hang() in its own header.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Migrate a few more files]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch add mmc and sd support for Mediatek MT7622 SoCs
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
For CMD21 tuning data, the 128/64 bytes data may coming in very
short time, before msdc_start_data(), the read data has already
come, in this case, clear MSDC_INT will cause the interrupt disappear
and lead to the thread hang.
the solution is just clear all interrupts before command was sent.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
This patch adds mmc support for MediaTek MT8512/MT8110 SoCs.
MT8512/MT8110 SoCs puts the tune register at top layer, so
need add new code to support it.
Signed-off-by: mingming lee <mingming.lee@mediatek.com>
It was observed (on ClearFog Base) that sending MMC APP_CMD returned
an error on the first attempt. The issue appears to be timing related
since even inserting a puts() short debug entry before the execution
added sufficient delay to receive success on first attempt.
Follow the existing quirks pattern to retry if initial issuance
failed so as to not introduce any delay unless needed.
Signed-off-by: Joel Johnson <mrjoel@lixil.net>
The eSDHC reference clocks should be provided by speed.c in arch/.
And we do not need CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK option to
select which clock to use. Because we can make the driver to select
the periperhal clock which is better (provides higher frequency)
automatically if its value is provided by speed.c.
This patch is to drop this option and make driver to select clock
automatically. Also fix peripheral clock calculation issue in
fsl_lsch2_speed.c/fsl_lsch3_speed.c.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fdt fixup for properties "peripheral-frequency" and "adapter-type"
was once for a Freescale SDK release. The properties haven't been existed
in linux mainline. Drop these useless code.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Add compatible "fsl,imxrt-usdhc" to make mmc working on i.MXRT platforms
with CONFIG_DM_MMC=y.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Not all architectures(i.e. i.MXRT) support mxc_get_clock() and use DM_CLK
instead. So building could result in failure due to missing
mxc_get_clock().
Make if(CONFIG_IS_ENABLED(CLK)) an #if statement.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
When no GPIO is used to read the card detect status the following
error is seen:
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... MMC: no card present
*** Warning - No block device, using default environment
Fix it by handling the "broken-cd" property in the same way
that drivers/mmc/sdhci.c does, which considers that the SD card
is present when the "broken-cd" property is passed.
Tested on a imx6ul-evk board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Convert clock manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get clock manager base address from DT node instead of using
#define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Convert system manager for Gen5, Arria 10 and Stratix 10 from struct
to defines.
Change to get system manager base address from DT node instead of
using #define.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Bring in the following merges:
commit 8fbbec12f7
Merge: 87f69f467a63618e71e8
Author: Tom Rini <trini@konsulko.com>
Date: Fri Jan 3 09:48:47 2020 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-fsl-qoriq into next
- updates and fixes on ls1028a, lx2, ls1046a, MC-DPSPARSER support
commit 87f69f467a
Merge: c0912f9bbf4466b99703
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 24 08:18:19 2019 -0500
Merge https://gitlab.denx.de/u-boot/custodians/u-boot-mpc85xx into next
- Enable DM driver on ppc/km boards
- Enable DM_USB for some of NXP powerpc platforms: P5040, T4240, T208x,
T104x, P4080, P2041, P2020, P1020, P3041
- Some updates in mpc85xx-ddr driver, km boards
commit c0912f9bbf
Merge: 533c9f5714a1d6dc3f84
Author: Tom Rini <trini@konsulko.com>
Date: Wed Dec 18 07:20:19 2019 -0500
Merge branch 'next' of https://gitlab.denx.de/u-boot/custodians/u-boot-x86 into next
- Various x86 common codes updated for TPL/SPL
- I2C designware driver updated for PCI
- ICH SPI driver updated to support Apollo Lake
- Add Intel FSP2 base support
- Intel Apollo Lake platform specific drivers support
- Add a new board Google Chromebook Coral
commit 533c9f5714
Merge: 553cb06887033e18b47b
Author: Tom Rini <trini@konsulko.com>
Date: Tue Dec 17 07:53:08 2019 -0500
Merge tag '20191217-for-next' of https://gitlab.denx.de/u-boot/custodians/u-boot-i2c into next
i2c: for next
- misc: i2c_eeprom:
Add partition support and add ability to query size
of eeprom device and partitions
- i2c common:
add support for offset overflow in to address and add
sandbox tests for it.
commit 553cb06887
Merge: f39abbbc53b4f98b3b16
Author: Tom Rini <trini@konsulko.com>
Date: Thu Dec 12 08:18:59 2019 -0500
Merge tag 'dm-next-13dec19' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm into next
buildman improvements including toolchain environment feature
sandbox unicode support in serial
Adam Ford reports that this change breaks booting on da850-evm and
Bartosz Golaszewski agrees that with the impending release we should
revert the change for now. With that noted:
This reverts commit 21a4d80a71.
Cc: Bartosz Golaszewski <brgl@bgdev.pl>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
At present if CONFIG_SPL_GPIO_SUPPORT is enabled then the GPIO uclass
is included in SPL/TPL without any control for boards. Some boards may
want to disable this to reduce code size where GPIOs are not needed in
SPL or TPL.
Add a new Kconfig option to permit this. Default it to 'y' so that
existing boards work correctly.
Change existing uses of CONFIG_DM_GPIO to CONFIG_IS_ENABLED(DM_GPIO) to
preserve the current behaviour. Also update the 74x164 GPIO driver since
it cannot build with SPL.
This allows us to remove the hacks in config_uncmd_spl.h and
Makefile.uncmd_spl (eventually those files should be removed).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The MMC boot is currently broken on omapl138-lcdk after enabling the
driver model in SPL. The main problem is the driver's bind callback not
being called after probe in SPL (even with the DM_FLAG_PRE_RELOC flag
specified).
While a proper fix is still being worked on, this hacky changeset at
least fixes the MMC boot on this platform by calling mmc_bind()
manually from probe().
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
struct mmc_config & struct mmc don't need to be exported over platform
data, but can instead be private in the driver.
Remove struct davinci_mmc_plat.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
The DM family of DaVinci SoCs is no longer supported. Drop the
irrelevant code from the driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function belongs in time.h so move it over and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of using single fixed value for the calibration offset,
add tables which dynamically adjust this per calibration code
from the SCC.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Some of the tuning taps produce suboptimal results. Add code
which skips those "bad" taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Check SCC for errors after check command if applicable and
optionally adjust the bus skew settings accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Disable the auto-retuning in HS400 mode in favor of manual calibration.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the TMPPORT3 offsets according to the latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Adjust the DT2FF offsets in HS400 according to latest information
from the chip vendor.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
The M3W up to ES1.2 uses 4 tuning taps for HS400, make it so.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the SMPCMP value from last calibration in private data.
This will be later used for skipping bad taps.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Retain the tap number from last calibration in private data. This
will be later used for SCC error checking after each command.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
This patch is to get clock directly from global data.
- Remove uclass clk api method. This was what i.MX platforms were
using, while QorIQ platforms weren't.
- Get clock only from global data, dropping mxc_get_clock().
QorIQ eSDHC controllers on one silicon use same reference clock.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Rockchips dwmmc controllers can't do dma to non-ddr addresses,
like for example the soc-internal sram but during boot parts of
TrustedFirmware need to be placed there from the read FIT image.
So add handling for a u-boot,spl-fifo-mode to not put the mmc
controllers into fifo mode for all time.
The regular fifo-mode property still takes precedent and only
if not set do we check for the spl-specific property.
Suggested-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
To enable HS400(ES) and UHS for imx8m platforms, update the driver data
to share with imx8qm esdhc_soc_data.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
During mmc initialization, there are several calls to mmc_set_clock
and mmc_set_ios. When mmc_power_off, the mmc->clock will be set,
but the imx driver will use 400KHz. So the following calls
to mmc_set_ios will set the clock several times which is redundant
in fsl_esdhc_imx driver. So let's simplify to remove redundant
clock settings.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The QorIQ eSDHC on all platforms supports checking write protect
state through register bit. So check it always.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
The fsl_esdhc_init() was actually to get configuration of mmc_config.
So rename it to fsl_esdhc_get_cfg_common() and make it common for both
DM_MMC and non-DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch is to clean up bus width setting code.
- For DM_MMC, remove getting "bus-width" from device tree.
This has been done in mmc_of_parse().
- For non-DM_MMC, move bus width configuration from fsl_esdhc_init()
to fsl_esdhc_initialize() which is non-DM_MMC specific.
And fix up bus width configuration to support only 1-bit, 4-bit,
or 8-bit. Keep using 8-bit if it's not set because many platforms
use driver without providing max bus width.
- Remove bus_width member from fsl_esdhc_priv structure.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Voltage validation should be done by CMD8. Current comparison between
mmc_cfg voltages and host voltage capabilities is meaningless.
So drop current comparison and let voltage validation is through CMD8.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Controller initialization is not needed in fsl_esdhc_init().
It will be done in esdhc_init() for non-DM_MMC, and in
esdhc_init_common() in probe for DM_MMC.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
A previous patch below adding DDR mode support was actually for i.MX
platforms. Now i.MX eSDHC driver is fsl_esdhc_imx.c. For QorIQ eSDHC,
it uses different process for DDR mode, and hasn't been supported.
Let's drop DDR support code for i.MX in fsl_esdhc driver.
0e1bf61 mmc: fsl_esdhc: Add support for DDR mode
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
U-boot prefers DM_MMC + BLK for MMC. Now eSDHC driver has already
support it, so let's force to use it.
- Drop non-BLK support for DM_MMC introduced by below patch.
66fa035 mmc: fsl_esdhc: fix probe issue without CONFIG_BLK enabled
- Support only DM_MMC + BLK (assuming BLK is always enabled for DM_MMC).
- Use DM_MMC instead of BLK for conditional compile.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
This patch adds a dts property cd-active-high for builtin-cd mode to make
it configurable instead of using hardcoded active-low.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
- Add sdhci driver for Broadcom iProc platform
- Add a driver callback for power-cycle for mmc
- Implement host_power_cycle callback for stm32_sdmmc2
- spl: dm_mmc: Initialize only the required mmc device
Power-domain is enabled by default in device_probe. am654 mmc driver
is enabling power-domain again in probe. As the second call is
redundant, drop power_domain_on from probe.
Tested-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
For the correct power cycle sequence with stm32_sdmmc2, the write of the
power cycle value in PWRCTL field of SDMMC_POWER register is now done in
stm32_sdmmc2_host_power_cycle() and no more in stm32_sdmmc2_pwrcycle().
Signed-off-by: Yann Gautier <yann.gautier@st.com>
Some MMC peripherals require specific power cycle sequence, where some
registers need to be written between the regulator is turned off and then
back on. This is the case for the MMC IP embedded in STM32MP1 SoC.
In STM32MP157 reference manual [1], the power cycle sequence is:
1. Reset the SDMMC with the RCC.SDMMCxRST register bit. This will reset
the SDMMC to the reset state and the CPSM and DPSM to the Idle state.
2. Disable the Vcc power to the card.
3. Set the SDMMC in power-cycle state. This will make that the
SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are driven low, to prevent the card
from being supplied through the signal lines.
4. After minimum 1ms enable the Vcc power to the card.
5. After the power ramp period set the SDMMC to the power-off state for
minimum 1ms. The SDMMC_D[7:0], SDMMC_CMD and SDMMC_CK are set to
drive “1”.
6. After the 1ms delay set the SDMMC to power-on state in which the
SDMMC_CK clock will be enabled.
7. After 74 SDMMC_CK cycles the first command can be sent to the card.
The step 3. cannot be handled by the current framework implementation.
A new callback (host_power_cycle) is created, and called in
mmc_power_cycle(), after mmc_power_off().
The incorrect power cycle sequence has shown some boot failures on
STM32MP1 with some SD-cards, especially on cold boots when the input
frequency is low (<= 25MHz).
Those failures are no more seen with this correct power cycle sequence.
[1] https://www.st.com/resource/en/reference_manual/DM00327659.pdf
Signed-off-by: Yann Gautier <yann.gautier@st.com>
In SPL, all the available mmc devices gets initialized during boot.
This might not work in cases where clocks are not available for
certain mmc devices(other than boot device) and the support for
enabling device might not be ready.
Texas Instruments' K3 J721E device having a central system controller
(dmsc) is one such example falling in this category. Below is the
sequence for the failing scenario:
- ROM comes up in SD mode and loads SPL by just initialing SD card.
- SPL loads dmsc firmware from SD Card.
Since ROM has enabled SD, SPL need not enable the SD, just need
to re initialize the card. But SPL is trying to initialize other MMC
instances which are in disabled state. Since dmsc firmware is not yet
available, devices cannot be enabled. So in SPL, initialize only the
mmc device that is needed.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
This change replaces printf() with debug() for the notification about
commands timeouts.
This is done on purpose (also other drivers use such approach - dw_mmc.c,
mvebu_mmc.c), as the mmc core code (mmc.c) uses timeouts to assess if one
is using sd card or eMMC device.
In such situation timeout is a some kind of a "normal" behavior and there
shall not be any output to the console.
There is no impact on boot time for boards using this driver (even in SPL)
when two extra timeouts are returned (no SD card present, only eMMC
available).
Boot time tested with grabserial:
sudo grabserial -b 115200 -d /dev/ttyUSB1 -e 30 -t -m "^U-Boot SPL*"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch converts the mxsmmc driver to support DM/DTS.
Moreover, it is also possible to use it in early SPL with
SPL_OF_PLATDATA enabled.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The zynq_sdhci drivers depends on DM_MMC in Kconfig so no need to check for
DM_MMC in the driver so this patch removes it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present there is only one control for this and it is used for both SPL
and TPL. But SPL might have a lot more space than TPL so the extra cost of
a full printf() might be acceptable.
Split the option into two, providing separate SPL and TPL controls. The
TPL setting defaults to the same as SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present running sandbox with valgrind produces some warnings due to the
MMC emulator not filling in all the expected fields. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: use sizeof() instead of hardcoded 16]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add eMMC hs200 mode for ls1028a, ls1012a, lx2160a.
This increases eMMC performance.
Tuning procedure is currently not supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
NXP fsl_esdhc controller supports two reference clocks:
platform clock and peripheral clock
Peripheral clock can provide higher clock frequency
which is required to be used for tuning of SD UHS mode
and eMMC HS200/HS400 modes.
Peripheral clock is enabled by default by defining config
option FSL_ESDHC_USE_PERIPHERAL_CLK if eMMC HS200/HS400 modes
are supported.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
-----BEGIN PGP SIGNATURE-----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=hWTf
-----END PGP SIGNATURE-----
Merge tag 'rpi-next-2019.10' of https://github.com/mbgg/u-boot
- fix mailbox status register used for polling
- fix bcm2835_sdhost to wait long enough for a transfer to complete
- increase kernel image size from 8 MB to 64 MB on arm64
- add support for RPi4
- add prefixes for raspberry pi related stuff to git-mailrc
The bcm2711 has two emmc controllers. The difference is the clocks
they use. Add support for the second emmc controller.
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Signed-off-by: Andrei Gherzan <andrei@balena.io>
Function bcm_2835_wait_transfer_complete() is not waiting long enough.
The previous code was claiming to wait for ~1 seconds, but as it depends
on register reads it's time actually varies.
Some cards require wait times of up to ~56 ms to perform
the command 'saveenv' on an EXT4 partition.
Re-implement the loop exit condition to use get_timer() which allows
to specify the wait time in more reliable manner. Set the maximum wait
time to the originally intended 1 second.
Signed-off by: Raul Benet <raul.benet_at_kaptivo.com>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
The sdhci capabilities registers can be incorrect. The
sdhci-caps-mask and sdhci-caps dt properties specify which bits of
the registers are incorrect and what their values should be. This
patch makes the sdhci driver use those properties to correct the caps.
Also use "dev_read_u64_default" instead of "dev_read_u32_array" for
caps mask.
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The mmc_spi driver's priv is not available in its bind phase(). Use
platdata instead.
Fixes: 05e35d4297 ("mmc: mmc_spi: Re-write driver using DM framework")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There are two cases not been considered:
- use uint for timeout, it will overflow when size bigger than 512KB for
it *8*1000 at the beginning, but we may use size up to 32MB; The
'timeout' will overflow if size bigger than 51.2MB after this fix, which
should be enough for U-Boot;
- The timeout is using clock speed for data rate, but the device may not
have such high speed, eg. clock is 52MHz while the device write speed may
be less than 10MB/s, and we may use up to 150MHz clock.
Fix them in this patch, the max timeout is about 6500 when size is 32MB
after fix.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
It's quite hard to figure out time units for various function that have
timeout parameters. This leads to possible errors when one forgets to
convert ms to us, for example. Let's rename those parameters
correspondingly to 'timeout_us' and 'timeout_ms' to prevent such issues
further.
While at it, add time units info as comments to struct mmc fields.
This commit doesn't change the behavior, only renames parameters names.
Buildman should report no changes at all.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
mmc_wait_dat0() expects timeout argument to be in usec units. But some
overlying functions operate on timeout in msec units. Convert timeout
from msec to usec when passing it to mmc_wait_dat0().
This fixes 'avb' commands on BeagleBoard X15, because next chain was
failing:
get_partition() -> mmc_switch_part() -> __mmc_switch() ->
mmc_wait_dat0()
when passing incorrect timeout from __mmc_switch() to mmc_wait_dat0().
Fixes: bb98b8c5c0 ("mmc: During a switch, poll on dat0 if available and check the final status")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Tested-by: Eugeniu Rosca <rosca.eugeniu@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
When look through the code, I found this bare metal
drives is not used, so remove it.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
eMMC device has multiple hw partitions both address from zero. However the
mmc driver lacks block cache invalidation for switch hwpart. This causes a
problem that data of current hw partition is cached before switching to
another hw partition. And the following read operation of the latter hw
partition will get wrong data when reading from the addresses that have
been cached previously.
To solve this problem, invalidate block cache after a successful
mmc_switch_part() operation.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-by: Felix Brack <fb@ltec.ch>
This patch solves a watchdog reset issue during mmc erase command.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
host->mmc, host->mmc->dev and host->mmc->priv must be set
before calling sdhci_setup_cfg() to avoid hang during mmc
initialization.
Thanks to commit 3d296365e4
("mmc: sdhci: Add support for sdhci-caps-mask") which put
this issue into evidence.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Increase SDMMC_BUSYD0END_TIMEOUT_US from 1s to 2s to
avoid timeout error during blocks erase on some sdcard
Issue seen on Kingston 16GB :
Device: STM32 SDMMC2
Manufacturer ID: 27
OEM: 5048
Name: SD16G
Bus Speed: 50000000
Mode: SD High Speed (50MHz)
card capabilities: widths [4, 1] modes [SD Legacy, SD High Speed (50MHz)]
host capabilities: widths [4, 1] modes [MMC legacy, SD Legacy, MMC High Speed (26MHz), SD High Speed (50MHz), MMC High Speed (52MHz)]
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 14.5 GiB
Bus Width: 4-bit
Erase Group Size: 512 Bytes
Issue reproduced with following command:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ... mmc erase failed
16384 blocks erased: ERROR
By setting SDMMC_BUSYD0END_TIMEOUT_US at 2 seconds and by adding
time measurement in stm32_sdmmc2_end_cmd() as shown below:
+start = get_timer(0);
/* Polling status register */
ret = readl_poll_timeout(priv->base + SDMMC_STA,
status, status & mask,
SDMMC_BUSYD0END_TIMEOUT_US);
+printf("time = %ld ms\n", get_timer(start));
We get the following trace:
STM32MP> mmc erase 0 100000
MMC erase: dev # 0, block # 0, count 1048576 ...
time = 17 ms
time = 1 ms
time = 1025 ms
time = 54 ms
time = 56 ms
time = 1021 ms
time = 57 ms
time = 56 ms
time = 1020 ms
time = 53 ms
time = 57 ms
time = 1021 ms
time = 53 ms
time = 57 ms
time = 1313 ms
time = 54 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
time = 1036 ms
time = 54 ms
time = 56 ms
time = 1028 ms
time = 53 ms
time = 56 ms
time = 1027 ms
time = 54 ms
time = 56 ms
time = 1024 ms
time = 54 ms
time = 56 ms
time = 1020 ms
time = 54 ms
time = 57 ms
time = 1023 ms
time = 54 ms
time = 56 ms
time = 1033 ms
time = 53 ms
time = 57 ms
....
time = 53 ms
time = 57 ms
time = 1021 ms
time = 56 ms
time = 56 ms
time = 1026 ms
time = 54 ms
time = 56 ms
1048576 blocks erased: OK
We see that 1 second timeout is not enough, we also see one measurement
up to 1313 ms. Set the timeout to 2 second to keep a security margin.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This converts the following to Kconfig:
CONFIG_FSL_USDHC
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Add IMX8M, TARGET_S32V234EVB to FSL_USDHC list]
Signed-off-by: Tom Rini <trini@konsulko.com>
This commit adds MMC driver support for HI3660 SoC reusing hi6220_dw_mmc
driver. Since HI3660 operates at different clock rate and uses fifo
mode now, let's introduce the platform data and utilize it for different
SoCs supported by this driver.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
This is a configuration option specific to the tegra controller.
Doing it this way makes it show up directly under the tegra controller
option, indented one level, as "Disable external clock loopback".
The way it is now, it shows up at the end of the controller list, not
indented, as if it's some kind of generic MMC configuration option.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Tom Warren <twarren@nvidia.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
- Add rk3399 boards Khadas Edge/-V/-Captain
- Add fully souce code support for rk3328 including TPL/DRAM init
- Enable boot from eMMC for rk3399 rock960/ficus boards
- turn on the IO supply for dw_mmc
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Vincent Tinelli <vincent.tinelli@intel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Matthias Brugger <mbrugger@suse.com>
Cc: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Eugen Hristev <eugen.hristev@microchip.com>
Since commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
[this patch is based on commit 41a9fab8da ("mmc: mv_sdhci: fix
uninitialized pointer deref on probe") by Baruch Siach]
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu102/zc706)
Select SPL_HS200_SUPPORT if SPL_HS400_SUPPORT is selected as is being
done for the U-boot case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The comment about init op being NULL used to be next to the NULL check
code. Commit 8ca51e51c1 ("dm: mmc: Add a way to use driver model for
MMC operations") separated the comment from the code. Put them back
together.
Fixes: 8ca51e51c1 ("dm: mmc: Add a way to use driver model for MMC operations")
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
When reading large data in once (reading 512MiB is tested on MT7623), a
watchdog timeout is triggered due to watchdog not being fed.
This patch adds WATCHDOG_RESET() to msdc_start_data() so the watchdog will
be fed every 1024 blocks are read/written.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
The standard property name for chip-detect gpio is "cd-gpios". All
in-tree DT files use only this name.
Fixes: 451931ea70 ("mmc: sdhci: Read cd-gpio from devicetree")
Cc: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Since commit 3d296365e4 ("mmc: sdhci: Add support for
sdhci-caps-mask") sdhci_setup_cfg() expects a valid sdhci_host mmc
field. Move the mmc field initialization before sdhci_setup_cfg()
call to avoid crash on mmc pointer dereference.
Fixes: 3d296365e4 ("mmc: sdhci: Add support for sdhci-caps-mask")
Cc: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Fixes the microSD slot on the ASUS C201.
Signed-off-by: Urja Rannikko <urjaman@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com<mailto:peng.fan@nxp.com>>
The j721e 4 bit instances don't have a hard DLL and therefore don't need
any DLL related configurations. Split the compatibles into an 8 bit and a
4 bit one. Add a private flags field which can be used to check if the
DLL is present and don't register the set_ios_post callback for the 4 bit
compatible instances.
Also update the compatibles in k3-j721e-main.dtsi to avoid breaking boot
with the new compatibles.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch fix mmc driver abort caused by below patch:
3d296365e4 mmc: sdhci: Add support for sdhci-caps-mask
After the patch sdhci_setup_cfg() access to host->mmc->dev,
so we have to do init before make the call to the function()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Most DM based SPI host controller drivers use SPI_XFER_BEGIN and
SPI_XFER_END flags to enable/disable slave chip select.
This patch extends MMC SPI driver to pass SPI_XFER_BEGIN flag when
MMC command is send at start and pass SPI_XFER_END flag using a
dummy transfer (of bitlen = 0) at the end of MMC command.
Suggested-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Sagar Kadam <sagar.kadam@sifive.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
We would like to use the driver even without power domains being
specified for cases such as during early boot when the required power
domains have already gotten enabled by the SoC's boot ROM and such
explicit initialization is not needed and possible.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add a platform specific set_control_reg() callback to help switch to
UHS speed modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The HOST_CONTROL2 register is a part of SDHC v3.00 and not just specific
to arasan/zynq controllers. Add the same to sdhci.h.
Also create a common API to set UHS timings in HOST_CONTROL2.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add support in the driver for handling phy specific registers.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The am654_sdhci driver needs to switch the clock off
before disabling its phy dll and needs to re-enable
the clock before enabling the phy again.
Therefore, make the sdhci_set_clock() function accessible
in the am654_sdhci driver.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add Support for masking some bits in the capabilities
register of a host controller.
Also remove the redundant readl() into caps1.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The host controller works perfectly well without having to add any
quirks. Remove them.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
Flash system partition with fastboot will earse the partition firstly
The 600ms timeout will fail on some SD Card. Enlarge it to 5s to make
it works for most of sdcard
Cc: guoyin.chen <guoyin.chen@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Implement set_enhanced_strobe hook for fsl_esdhc_imx,
,in esdhc_set_timing and esdhc_change_pinstate, also handle HS400_ES.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
eMMC 5.1+ supports HS400 Enhances Strobe mode without the need for
tuning procedure.
The flow is as following:
- set HS_TIMIMG (Highspeed)
- Host change freq to <= 52Mhz
- set the bus width to Enhanced strobe and DDR8Bit(CMD6),
EXT_CSD[183] = 0x86 instead of 0x80
- set HS_TIMING to 0x3 (HS400)
- Host change freq to <= 200Mhz
- Host select HS400 enhanced strobe complete
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Should use CONFIG_IS_ENABLED not IS_ENABLED for clock and regulator drivers,
CONFIG_IS_ENABLED will check the CONFIG_SPL_CLK and CONFIG_SPL_DM_REGULATOR
when building SPL.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This patch rewrites MMC SPI driver using U-Boot DM
framework and get it's working on SiFive Unleashed
board.
Signed-off-by: Bhargav Shah <bhargavshah1988@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
The MMC mode and width are fixed for MMC SPI host hence we skip
sd_select_mode_and_width() and mmc_select_mode_and_width() for
MMC SPI host.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Accessing the boot partition had been error prone with HS200 and HS400 and
was disabled. The driver first switched to a lesser mode and then switched
the partition access. It was mostly due to a bad handling of the switch and
has been fixed, so let's remove this 'feature'
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The switch operation can sometimes make the bus unreliable, in that case
the send_status parameter should be false to indicate not to poll using
CMD13. If polling on dat0 is possible, we should use it to detect the end
of the operation.
At the end of the operation it is safe to use CMD13 to get the status of
the card. It is important to do so because the operation may have failed.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
The e-MMC spec allows the e-MMC to specify a timeout for the partition
switch command. It can take up to 2550 ms. There is no lower limit to this
value in the spec, but do as the the linux driver does and force it to be
at least 300ms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Starting with rev 4.5, the eMMC can define a generic timeout for the
SWITCH command.
Following Linux Kernel code, the timeout also changed from 1000 -> 500
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Using the DAT0 line as a rdy/busy line is an alternative to reading the
status register of the card. It especially useful in situation where the
bus is not in a good shape, like when modes are switched.
This is also how the linux driver behaves.
Note of warning: As per the specification, while polling on DAT0 the CLK
must not turned off: "[...] Without a clock edge the Device (unless
previously disconnected by a deselect command (CMD7)) will force the DAT0
line down, forever. [...]"
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>