The LBLAW_* values determine the window configuration of the memory
controller. Hence, they must be known at compile time, and cannot be
implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The BATs (block address translation registers) determine the initial
memory window mappings. Hence, they must be known at compile time and
cannot be implemented in the DT mechanism.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx DM timer driver disables arch.pciexp*_clk, and uses
clk_get_rate instead. But the legacy MPC83xx PCIe driver still uses
arch.pciexp*_clk for the clock.
Hence, read the PCIe clock from the registers in the legacy MPC83xx PCIe
driver.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The HRCW (hardware reset configuration word) is a constant that must be
hard-coded into the boot loader image. So, it must be available at
compile time, and cannot be migrated to the DT mechanism, but has to be
kept in Kconfig.
Configuration of this crucial variable should still be somewhat
comfortable. Hence, make its fields configurable in Kconfig, and
assemble the final value from these.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC83xx uses CONFIG_83XX_CLKIN instead of CONFIG_SYS_CLK_FREQ to set the
system clock. To migrate the architecture, we can replace
CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ.
To do this
* replace all occurrences of CONFIG_83XX_CLKIN with CONFIG_SYS_CLK_FREQ
* set CONFIG_SYS_CLK_FREQ to the old value of CONFIG_83XX_CLKIN in all
MPC83xx config files
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_SYS_CLK_FREQ is the standard way to set the system clock
frequency. On MPC83xx, CONFIG_83XX_CLKIN is used for this purpose.
Hence, the obvious way is to replace CONFIG_83XX_CLKIN with
CONFIG_SYS_CLK_FREQ.
A few MPC83xx boards use the CONFIG_83XX_CLKIN variable for computing
CONFIG_SYS_NS16550_CLK. This makes it harder to replace
CONFIG_83XX_CLKIN.
But the value of the multiplicator can be read from the SPMR register.
Hence, replace the static calculations with a call to a new get_bus_freq
function, as other architectures do.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC83xx include files contain some settings of the PCI subsystem.
Migrate these to Kconfig until a proper DM PCI driver exists.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_MPC837XERDB is unused, and TARGET_MPC837XERDB could replace it.
Hence, get rid of CONFIG_MPC837XERDB.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_MPC837XEMDS is unused, and TARGET_MPC837XEMDS could replace it.
Hence, get rid of CONFIG_MPC837XEMDS.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_MPC8315ERDB is unused, and TARGET_MPC8315ERDB could replace it.
Hence, get rid of CONFIG_MPC8315ERDB.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_MPC8313ERDB is unused, and
TARGET_MPC8313ERDB_NAND/TARGET_MPC8313ERDB_NOR Kconfig could replace it.
Hence, get rid of CONFIG_MPC8313ERDB.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC8349ITX Kconfig option to replace the
CONFIG_MPC8349ITX ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Use the proper CONFIG_TARGET_MPC832XEMDS Kconfig option to replace the
CONFIG_MPC832XEMDS ad-hoc config option.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The ve8313 has the option of either configuring the eLBC (enhanced local system bus) such that
* NOR flash is the first memory bank, and NAND flash is the second memory bank, or
* NAND flash is the first memory bank, and NOR flash is the second memory bank,
by using CONFIG_SYS_NOR_{BR,OR}_PRELIM and
CONFIG_SYS_NAND_{BR,OR}_PRELIM for defining
CONFIG_SYS_{BR,OR}{0,1}_PRELIM.
After Kconfig migration, replacing some lines in the defconfig will have
the same effect.
Hence, we will not create distinct ve8313_{NOR,NAND} configs for such a
small change.
Instead, fix the current default (NOR first, NAND second), and unroll
the CONFIG_SYS_NAND_{BR,OR}_PRELIM options. This will ease the Kconfig
migration
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The mpc8315erdb has the option of either configuring the eLBC (enhanced
local system bus) such that
* NOR flash is the first memory bank, and NAND flash is the second
memory bank, or
* NAND flash is the first memory bank, and NOR flash is the second
memory bank,
by using CONFIG_SYS_NOR_{BR,OR}_PRELIM and
CONFIG_SYS_NAND_{BR,OR}_PRELIM for defining
CONFIG_SYS_{BR,OR}{0,1}_PRELIM.
After Kconfig migration, replacing some lines in the defconfig will have
the same effect.
Hence, we will not create distinct ve8313_{NOR,NAND} configs for such a small change.
Instead, fix the current default (NOR first, NAND second), and unroll
the CONFIG_SYS_NAND_{BR,OR}_PRELIM options. This will ease the Kconfig
migration.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The MPC8349EMDS config file contains config options to enable SDRAM
support. To keep this ability after the Kconfig migration, create a new
MPC8349EMDS_SDRAM board that enables the SDRAM support and remove the
SDRAM support from the original board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
NanoPi M1 plus have a 10/100/1000M ethernet with external phy.
Phy power is controlled by PD6.
Add the required configuration for it.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
SPL_TEXT_BASE was moved into Kconfig, which previously part of
include/configs before this teres_i support gets merged.
Fix it by explicitly define in defconfig like other boards does.
Signed-off-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
SPL_TEXT_BASE has been moved to Kconfig with commit:
f89d6133ee configs: move CONFIG_SPL_TEXT_BASE to Kconfig
But Beelink GS1 config file has been introduced in the
same time without this modification.
Fix this by settings the CONFIG_SPL_TEXT_BASE
Suggested-by: Jonas Smedegaard <dr@jones.dk>
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Some H6 boards have a watchdog which didn't make the SoC
reboot properly.
Reason is still unknown but several people have test it.
Chen-Yu Tsai :
Pine H64 = H6 V200-AWIN H6448BA 7782 => OK
OrangePi Lite 2 = H6 V200-AWIN H8068BA 61C2 => KO
Martin Ayotte :
Pine H64 = H8069BA 6892 => OK
OrangePi 3 = HA047BA 69W2 => KO
OrangePi One Plus = H7310BA 6842 => KO
OrangePi Lite2 = H6448BA 6662 => KO
Clément Péron:
Beelink GS1 = H6 V200-AWIN H7309BA 6842 => KO
After the series of result, Icenowy try to reach Allwinner about this
issue but they seems not interested to investigate it.
As we don't have the ARIS coproc to do power management and watchdogis
the only solution to reset the board.
So, Change from watchdog to R_watchdog to allow a reboot on all H6
boards.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The LSDMR_* macros are used to configure the system bus on MPC83xx.
A few of the possible LSDMR_* macros were never defined in the
respective include files. This renders the SDRAM support on the
MPC8349EMDS unusable, because it uses these undefined macros.
To make the SDRAM option work, introduce these macros into the proper
config file.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
vme8349.h contains two separate boards: The vme8349 itself, and the
caddy2 board. The caddy2 board is chosen by setting certain config
variables. Create a proper config file for the caddy2 board to make
Kconfig migration easier.
Furthermore, simplify the vme8349 and caddy2 configs by keeping only the
options necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
CONFIG_TARGET_VME8349 can replace CONFIG_VME8349. Hence, replace
CONFIG_VME8349 with CONFIG_TARGET_VME8349, and remove CONFIG_VME8349.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
MPC8313ERDB has the option of either enabling NOR or NAND boot in its
config file (by commenting out certain #ifdefs). To keep this ability
after migrating options to Kconfig, we introduce two MPC8313ERDB
configs: one for NOR, and one for NAND.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmeter1, and kmcoge5ne boards also build from the same config
file with #ifdef logic.
Create a separate include config for each board with the #ifdef logic
resolved as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Simplify the keymile config files once more by unrolling the
km/km83xx-common.h, and resolve the #ifdef logic as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmsupx5, tuge1, kmopti2, and kmtepr2 boards all build from the same
include config file with lots of #ifdef logic.
To ease Kconfig migration, create new config include files for these
boards, and resolve the #ifdef logic as needed.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
To further simplify config include files, unroll the km/km8309-common.h
and km/km8321-common.h include files.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
We want to unroll several include files, while keeping include
statements consistent.
To make it easier to not break the include statements, move the include
files to the main configs directory. All three include files moved will
be unrolled, so they won't pollute the directory for long.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The kmtegr1, kmvect1, and suvd3 boards all use the same config include
file with lots of #ifdefs in it.
The Kconfig migation will become easier if we get rid of these #ifdefs
first.
Hence, create distinct config include files for these boards, and unwind
the #ifdef logic in these config files to only include the options
necessary for each board.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Pull the vidconsole_put_string() function from DM tests, make it
available to e.g. boards that want to display information on the
LCD on boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
The IPUv3 can handle 1920x1080x32bpp displays , set the max preallocated
framebuffer BPP to 32 to cater for all eventualities.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Meet the following boot hang.
"
U-Boot SPL 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00661-gdc80a012e4 (Apr 25 2019 - 10:31:57 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C)Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
Video device 'ipu@2400000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Video device 'ipu@2800000' cannot allocate frame buffer memory -ensure the device is set up before relocation
Error binding driver 'ipuv3_video': -28
Some drivers failed to bind
Error binding driver 'generic_simple_bus': -28
Some drivers failed to bind
initcall sequence 4ffe4500 failed at call 1780dfb7 (err=-28)
"
1. fdtdec_get_alias_seq will use "video" as base, however in alias node,
we use ipux, so add new alias for U-Boot dts.
2. DM_VIDEO is enabled, however reserve_video is called before
relocation, so to make DM_VIDEO work before relocation, need to
set SYS_MALLOC_F_LEN
3. defconfig is updated with savedefconfig
Note: I do not have a video panel to test, but with this patch, U-Boot
boots up again, below log.
"
U-Boot SPL 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
Trying to boot from MMC1
U-Boot 2019.04-00662-g0b62453bff (Apr 25 2019 - 10:36:31 +0800)
CPU: Freescale i.MX6Q rev1.5 996 MHz (running at 792 MHz)
CPU: Automotive temperature grade (-40C to 125C) at 34C
Reset cause: POR
Model: Freescale i.MX6 Quad SABRE Smart Device Board
Board: MX6-SabreSD
I2C: ready
DRAM: 1 GiB
PMIC: PFUZE100 ID=0x10
MMC: FSL_SDHC: 0, FSL_SDHC: 1, FSL_SDHC: 3
Loading Environment from MMC... *** Warning - bad CRC, using default environment
PCI: pcie phy link never came up
In: serial
Out: serial
Err: serial
Net: FEC [PRIME]
Hit any key to stop autoboot: 0
"
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
There are several includes in mx53cx9020.c which are not required
anymore.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
These mmc functions were not used anymore since DM_MMC was introduced.
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Enable DM_VIDEO in config and don't overwrite console so it can be set
from environment
Acked-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
The ipu node in imx53 is needed for DM_VIDEO. We also need to set
u-boot,dm-pre-reloc to initialize before relocation.
Signed-off-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
