Allow the led bcm6858 driver to be used on bcm63158.
They have the same led controller.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
On response type r1b, if DTIME is not defined or too short,
the Datatimeout and DPSM flag occurs. Like the DPSM is
activated all next data transfer will be frozen.
To avoid this freeze:
-The driver must define a DTIME on all r1b response type.
-DTIME of SDMMC must be defined for alls stop transmission
(for read and write request) even if MMC_RSP_BUSY is not set.
-If busy timeout occur, an abort request must be sent to
reinitialize the DPSM.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested-by: Patrick DELAUNAY <patrick.delaunay@st.com>
This is needed to make ethernet work on stm32f746-eval which
uses MII mode.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This config file is shared between stm32f746-disco and stm32f769-disco.
These 2 boards doesn't embed the same qspi flash (Micron n25q128a on
f746-disco, Macronix mx66l51235l on f769-disco).
To be able to use Macronix mx66l51235l on F769-disco, flags
SPI_FLASH_MACRONIX must be enabled.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Allows to boot linux distribution.
As stm32f746-disco and stm32f769-disco are sharing the same defconfig
file, in case of stm32f769-disco build, "fdtfile=..." must be updated
with the correct stm32f769 DTB file name.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Initially the compatible string was wrongly set to "st,stm32f4xx-sdio".
Use compatible string used by kernel instead and identify mmci variant
using "arm,primecell-periphid" property.
Currently, the DM part of mmci driver is only used by STM32 SoCs,
that's why the switch case gets only one entry. It will be populated
easily with new variant in the future.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As U-boot stm32f clock driver doesn't support new
bindings for auxiliary clocks (clocks = <&rcc 1 ....>),
restore old bindings for usart1 to get console output.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Synchronize stm32h7 device tree with kernel v4.20.
U-boot DT files and pinctrl bindings are updated,
useless nodes are removed and gpio compatible added.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
As sdmmc is not yet supported on kernel side, sdmmc nodes
are located in eval-u-boot and disco-u-boot DT files.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In order to prepare and ease future DT synchronization with kernel
DT, migrate all U-boot specific nodes/properties/addons to
U-boot DT files.
Migrate also DT nodes which are not yet available on kernel DT side
as ethernet, ltdc and qspi nodes.
Fix ethernet_mii pins and add missing qspi_pins for stm32746g-eval
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
When using the generic PHY on boards using an RGMII Realtek PHY,
gigabit speed is not always reliable.
This patch enables the Realtek PHY driver for such boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Amlogic U200 board is based on the Amlogic S905D2 SoC
from the Amlogic G12A SoC family.
The board has the following specifications :
- Amlogic S905D2 ARM Cortex-A53 quad-core SoC
- XGB DDR4 SDRAM
- 10/100 Ethernet (Internal PHY)
- 1 x USB 3.0 Host
- eMMC
- SDcard
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connector
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Import Linux 5.1-rc1 DT from 9e98c678c2d6 ("Linux 5.1-rc1") for the
meson-g12a-u200 board, the meson-g12a.dtsi and the corresponding bindings.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add support for the Amlogic G12A SoC, which is a mix between the
new physical memory mapping of AXG and the functionnalities of
the previous Amlogic GXL/GXM SoCs.
To handle the internal ethernet PHY, the Amlogic G12A SoCs now
embeds a dedicated PLL to feed the internal PHY.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add basic support for the Amlogic G12A clock controller based on
the AXG driver.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
In order to support the Amlogic G12A clock controller,
re-architect the clock files into a meson directory.
No functionnal changes.
MAINTAINERS entry is also updated.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add pinctrl support for the Amlogic G12A SoC, which is
very similar to the Amlogic AXG support but with an additionnal
drive-strength register bank.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When creating a device path node ensure that the size of the allocated
memory at lest matches the size of the node header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The EBBR specification prescribes that we should have either an ACPI table
or a device tree but not both. Let us enforce this condition in the
`bootefi` command.
If the bootefi command is called without a device tree parameter use a
previously device tree or fall back to the internal device tree.
The fdt unit test should not be run on boards with an ACPI table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The EBBR specification prescribes that we should have either an ACPI table
or a device tree but not both.
So do not run the device tree unit test on boards with an ACPI table.
Hence there is no need any longer to make it 'on request' only.
Do not pass $fdtcontroladdr to `bootefi selftest`.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We already can let a Python test depend on a build option being set via
@pytest.mark.buildconfigspec(). It may be necessary to let a test depend on
a build option *not* being set. So let's introduce
@pytest.mark.notbuildconfigspec
for this purpose.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
vexpress_ca15_tc2_defconfig and vexpress_ca9x4_defconfig do not provide
device trees (as $fdtcontroladdr) as needed to pass our Travis CI tests.
As we are on the move to requiring block devices to be based on the driver
model these boards either will have to be converted to use device trees or
will be kicked out of U-Boot.
So let's disable CONFIG_EFI_LOADER on these boards until the device tree
issue is resolved.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the current implementation, bootefi command and EFI boot manager
don't use load_image API, instead, use more primitive and internal
functions. This will introduce duplicated code and potentially
unknown bugs as well as inconsistent behaviours.
With this patch, do_efibootmgr() and do_boot_efi() are completely
overhauled and re-implemented using load_image API.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Use efi_root as parent handle for the loaded image.
LoadImage() should be called with BootPolicy = true by the boot manager.
Avoid duplicate free_pool().
Eliminate variable memdp which is not needed after anymore due to
"efi_loader: correctly split device path of loaded image".
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When the LoadImage() service is called for an image that is already loaded
to memory the file path may be NULL or it will contain both a device path
as well as a media path. We should not assume that there is no media path.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
All the non-boot-manager-based (that is, bootefi <addr>) code is put
into one function, do_bootefi_image().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
do_bootmgr_exec() is renamed to do_efibootmgr() as we put all the necessary
code into this function.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Efi_selftest code is unusual in terms of execution path in do_bootefi(),
which make that function complicated and hard to understand. With this
patch, all efi_selftest related code will be put in a separate function.
The change also includes expanding efi_run_prepare() and efi_run_finish()
in do_bootefi_exec().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
For simplicity, merge two functions.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Return error code of efi_install_configuration_table() when aborting from
efi_install_fdt().
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Carve out a function to handle the installation of the device tree
as a configuration table in system table.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
set_load_options() can fail, so it should return error code to stop
invoking an image.
In addition, set_load_options() now takes a handle, instead of
loaded_image_info, to utilize efi_load_image() in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The `efidebug dh` command shows handles and the installed protocols. For
most of the protocols implemented by U-Boot a short text was shown. But for
some only the GUID was displayed.
Provide the missing short texts for the following protocols: HII String,
HII Database, HII Config Routing, Simple Network, PXE Base Code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should consistently use the same name for protocol GUIDs as defined in
the UEFI specification. Not adhering to this rule has led to duplicate
definitions for the EFI_LOADED_IMAGE_PROTOCOL_GUID.
Adjust misnamed protocol GUIDs.
Adjust the text for the graphics output protocol in the output of the
`efidebug dh` command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch.
The root node handle will be used as a dummy parent handle when invoking
an EFI image from bootefi/bootmgr command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Rebased.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch.
efi_dp_split_file_path() is used to create device_path and file_path
from file_path for efi_setup_loaded_image().
In a special case, however, of HARDWARE_DEVICE/MEMORY, it doesn't
work expectedly since this path doesn't contain any FILE_PATH sub-type.
This patch makes a workaround.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Adjust the logic such that for all paths that do no end on a media file
path we return NULL as file_path.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The driver add the support of the led IP on bcm6858.
This led IP can drive up to 32 leds, and can handle
blinking.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
