led: add initial support for bcm6858
The driver add the support of the led IP on bcm6858. This led IP can drive up to 32 leds, and can handle blinking. Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com> Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This commit is contained in:
Philippe Reynes
Tom Rini
parent
98ffbb78e1
commit
d00c6a2d56
|
|
@ -0,0 +1,51 @@
|
|||
LEDs connected to Broadcom BCM6858 controller
|
||||
|
||||
This controller is present on BCM6858, BCM6328, BCM6362 and BCM63268.
|
||||
In these SoCs it's possible to control LEDs both as GPIOs or by hardware.
|
||||
|
||||
Required properties:
|
||||
- compatible : should be "brcm,bcm6858-leds".
|
||||
- #address-cells : must be 1.
|
||||
- #size-cells : must be 0.
|
||||
- reg : BCM6858 LED controller address and size.
|
||||
|
||||
Optional properties:
|
||||
- brcm,serial-led-msb-first : Boolean, msb data come out first on serial data pin
|
||||
Default : false
|
||||
- brcm,serial-led-en-pol : Boolean, serial led polarity (true => active high)
|
||||
Default : false
|
||||
- brcm,serial-led-clk-pol : Boolean, serial clock polarity (true => active high)
|
||||
Default : false
|
||||
- brcm,serial-led-data-ppol : Boolean, serial data polarity (true => active high)
|
||||
Default : false
|
||||
- brcm,serial-shift-inv : Boolean, led test mode
|
||||
Default : false
|
||||
|
||||
Each LED is represented as a sub-node of the brcm,bcm6858-leds device.
|
||||
|
||||
LED sub-node required properties:
|
||||
- reg : LED pin number (only LEDs 0 to 32 are valid).
|
||||
|
||||
LED sub-node optional properties:
|
||||
- label : see Documentation/devicetree/bindings/leds/common.txt
|
||||
- active-low : Boolean, makes LED active low.
|
||||
Default : false
|
||||
|
||||
Examples:
|
||||
BCM6328 with 2 GPIO LEDs
|
||||
leds0: led-controller@ff800800 {
|
||||
compatible = "brcm,bcm6858-leds";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
reg = <0x0 0xff800800 0x0 0xe4>;
|
||||
|
||||
led@2 {
|
||||
reg = <2>;
|
||||
label = "green:inet";
|
||||
};
|
||||
|
||||
led@5 {
|
||||
reg = <5>;
|
||||
label = "red:alarm";
|
||||
};
|
||||
};
|
||||
|
|
@ -28,6 +28,13 @@ config LED_BCM6358
|
|||
LED HW controller accessed via MMIO registers.
|
||||
HW has no blinking capabilities and up to 32 LEDs can be controlled.
|
||||
|
||||
config LED_BCM6858
|
||||
bool "LED Support for BCM6858"
|
||||
depends on LED && ARCH_BCM6858
|
||||
help
|
||||
This option enables support for LEDs connected to the BCM6858
|
||||
HW has blinking capabilities and up to 32 LEDs can be controlled.
|
||||
|
||||
config LED_BLINK
|
||||
bool "Support LED blinking"
|
||||
depends on LED
|
||||
|
|
|
|||
|
|
@ -6,4 +6,5 @@
|
|||
obj-y += led-uclass.o
|
||||
obj-$(CONFIG_LED_BCM6328) += led_bcm6328.o
|
||||
obj-$(CONFIG_LED_BCM6358) += led_bcm6358.o
|
||||
obj-$(CONFIG_LED_BCM6858) += led_bcm6858.o
|
||||
obj-$(CONFIG_$(SPL_)LED_GPIO) += led_gpio.o
|
||||
|
|
|
|||
|
|
@ -0,0 +1,250 @@
|
|||
// SPDX-License-Identifier: GPL-2.0+
|
||||
/*
|
||||
* Copyright (C) 2019 Philippe Reynes <philippe.reynes@softathome.com>
|
||||
*
|
||||
* based on:
|
||||
* drivers/led/led_bcm6328.c
|
||||
* drivers/led/led_bcm6358.c
|
||||
*/
|
||||
|
||||
#include <common.h>
|
||||
#include <dm.h>
|
||||
#include <errno.h>
|
||||
#include <led.h>
|
||||
#include <asm/io.h>
|
||||
#include <dm/lists.h>
|
||||
|
||||
#define LEDS_MAX 32
|
||||
#define LEDS_WAIT 100
|
||||
|
||||
/* LED Mode register */
|
||||
#define LED_MODE_REG 0x0
|
||||
#define LED_MODE_OFF 0
|
||||
#define LED_MODE_ON 1
|
||||
#define LED_MODE_MASK 1
|
||||
|
||||
/* LED Controller Global settings register */
|
||||
#define LED_CTRL_REG 0x00
|
||||
#define LED_CTRL_MASK 0x1f
|
||||
#define LED_CTRL_LED_TEST_MODE BIT(0)
|
||||
#define LED_CTRL_SERIAL_LED_DATA_PPOL BIT(1)
|
||||
#define LED_CTRL_SERIAL_LED_CLK_POL BIT(2)
|
||||
#define LED_CTRL_SERIAL_LED_EN_POL BIT(3)
|
||||
#define LED_CTRL_SERIAL_LED_MSB_FIRST BIT(4)
|
||||
|
||||
/* LED Controller IP LED source select register */
|
||||
#define LED_HW_LED_EN_REG 0x08
|
||||
/* LED Flash control register0 */
|
||||
#define LED_FLASH_RATE_CONTROL_REG0 0x10
|
||||
/* Soft LED input register */
|
||||
#define LED_SW_LED_IP_REG 0xb8
|
||||
/* Soft LED input polarity register */
|
||||
#define LED_SW_LED_IP_PPOL_REG 0xbc
|
||||
|
||||
struct bcm6858_led_priv {
|
||||
void __iomem *regs;
|
||||
u8 pin;
|
||||
};
|
||||
|
||||
#ifdef CONFIG_LED_BLINK
|
||||
/*
|
||||
* The value for flash rate are:
|
||||
* 0 : no blinking
|
||||
* 1 : rate is 25 Hz => 40 ms (period)
|
||||
* 2 : rate is 12.5 Hz => 80 ms (period)
|
||||
* 3 : rate is 6.25 Hz => 160 ms (period)
|
||||
* 4 : rate is 3.125 Hz => 320 ms (period)
|
||||
* 5 : rate is 1.5625 Hz => 640 ms (period)
|
||||
* 6 : rate is 0.7815 Hz => 1280 ms (period)
|
||||
* 7 : rate is 0.390625 Hz => 2560 ms (period)
|
||||
*/
|
||||
static const int bcm6858_flash_rate[8] = {
|
||||
0, 40, 80, 160, 320, 640, 1280, 2560
|
||||
};
|
||||
|
||||
static u32 bcm6858_flash_rate_value(int period_ms)
|
||||
{
|
||||
unsigned long value = 7;
|
||||
int i;
|
||||
|
||||
for (i = 0; i < ARRAY_SIZE(bcm6858_flash_rate); i++) {
|
||||
if (period_ms <= bcm6858_flash_rate[i]) {
|
||||
value = i;
|
||||
break;
|
||||
}
|
||||
}
|
||||
|
||||
return value;
|
||||
}
|
||||
|
||||
static int bcm6858_led_set_period(struct udevice *dev, int period_ms)
|
||||
{
|
||||
struct bcm6858_led_priv *priv = dev_get_priv(dev);
|
||||
u32 offset, shift, mask, value;
|
||||
|
||||
offset = (priv->pin / 8) * 4;
|
||||
shift = (priv->pin % 8) * 4;
|
||||
mask = 0x7 << shift;
|
||||
value = bcm6858_flash_rate_value(period_ms) << shift;
|
||||
|
||||
clrbits_32(priv->regs + LED_FLASH_RATE_CONTROL_REG0 + offset, mask);
|
||||
setbits_32(priv->regs + LED_FLASH_RATE_CONTROL_REG0 + offset, value);
|
||||
|
||||
return 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
static enum led_state_t bcm6858_led_get_state(struct udevice *dev)
|
||||
{
|
||||
struct bcm6858_led_priv *priv = dev_get_priv(dev);
|
||||
enum led_state_t state = LEDST_OFF;
|
||||
u32 sw_led_ip;
|
||||
|
||||
sw_led_ip = readl(priv->regs + LED_SW_LED_IP_REG);
|
||||
if (sw_led_ip & (1 << priv->pin))
|
||||
state = LEDST_ON;
|
||||
|
||||
return state;
|
||||
}
|
||||
|
||||
static int bcm6858_led_set_state(struct udevice *dev, enum led_state_t state)
|
||||
{
|
||||
struct bcm6858_led_priv *priv = dev_get_priv(dev);
|
||||
|
||||
switch (state) {
|
||||
case LEDST_OFF:
|
||||
clrbits_32(priv->regs + LED_SW_LED_IP_REG, (1 << priv->pin));
|
||||
#ifdef CONFIG_LED_BLINK
|
||||
bcm6858_led_set_period(dev, 0);
|
||||
#endif
|
||||
break;
|
||||
case LEDST_ON:
|
||||
setbits_32(priv->regs + LED_SW_LED_IP_REG, (1 << priv->pin));
|
||||
#ifdef CONFIG_LED_BLINK
|
||||
bcm6858_led_set_period(dev, 0);
|
||||
#endif
|
||||
break;
|
||||
case LEDST_TOGGLE:
|
||||
if (bcm6858_led_get_state(dev) == LEDST_OFF)
|
||||
return bcm6858_led_set_state(dev, LEDST_ON);
|
||||
else
|
||||
return bcm6858_led_set_state(dev, LEDST_OFF);
|
||||
break;
|
||||
#ifdef CONFIG_LED_BLINK
|
||||
case LEDST_BLINK:
|
||||
setbits_32(priv->regs + LED_SW_LED_IP_REG, (1 << priv->pin));
|
||||
break;
|
||||
#endif
|
||||
default:
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct led_ops bcm6858_led_ops = {
|
||||
.get_state = bcm6858_led_get_state,
|
||||
.set_state = bcm6858_led_set_state,
|
||||
#ifdef CONFIG_LED_BLINK
|
||||
.set_period = bcm6858_led_set_period,
|
||||
#endif
|
||||
};
|
||||
|
||||
static int bcm6858_led_probe(struct udevice *dev)
|
||||
{
|
||||
struct led_uc_plat *uc_plat = dev_get_uclass_platdata(dev);
|
||||
|
||||
/* Top-level LED node */
|
||||
if (!uc_plat->label) {
|
||||
void __iomem *regs;
|
||||
u32 set_bits = 0;
|
||||
|
||||
regs = dev_remap_addr(dev);
|
||||
if (!regs)
|
||||
return -EINVAL;
|
||||
|
||||
if (dev_read_bool(dev, "brcm,serial-led-msb-first"))
|
||||
set_bits |= LED_CTRL_SERIAL_LED_MSB_FIRST;
|
||||
if (dev_read_bool(dev, "brcm,serial-led-en-pol"))
|
||||
set_bits |= LED_CTRL_SERIAL_LED_EN_POL;
|
||||
if (dev_read_bool(dev, "brcm,serial-led-clk-pol"))
|
||||
set_bits |= LED_CTRL_SERIAL_LED_CLK_POL;
|
||||
if (dev_read_bool(dev, "brcm,serial-led-data-ppol"))
|
||||
set_bits |= LED_CTRL_SERIAL_LED_DATA_PPOL;
|
||||
if (dev_read_bool(dev, "brcm,led-test-mode"))
|
||||
set_bits |= LED_CTRL_LED_TEST_MODE;
|
||||
|
||||
clrsetbits_32(regs + LED_CTRL_REG, ~0, set_bits);
|
||||
} else {
|
||||
struct bcm6858_led_priv *priv = dev_get_priv(dev);
|
||||
void __iomem *regs;
|
||||
unsigned int pin;
|
||||
|
||||
regs = dev_remap_addr(dev_get_parent(dev));
|
||||
if (!regs)
|
||||
return -EINVAL;
|
||||
|
||||
pin = dev_read_u32_default(dev, "reg", LEDS_MAX);
|
||||
if (pin >= LEDS_MAX)
|
||||
return -EINVAL;
|
||||
|
||||
priv->regs = regs;
|
||||
priv->pin = pin;
|
||||
|
||||
/* this led is managed by software */
|
||||
clrbits_32(regs + LED_HW_LED_EN_REG, 1 << pin);
|
||||
|
||||
/* configure the polarity */
|
||||
if (dev_read_bool(dev, "active-low"))
|
||||
clrbits_32(regs + LED_SW_LED_IP_PPOL_REG, 1 << pin);
|
||||
else
|
||||
setbits_32(regs + LED_SW_LED_IP_PPOL_REG, 1 << pin);
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static int bcm6858_led_bind(struct udevice *parent)
|
||||
{
|
||||
ofnode node;
|
||||
|
||||
dev_for_each_subnode(node, parent) {
|
||||
struct led_uc_plat *uc_plat;
|
||||
struct udevice *dev;
|
||||
const char *label;
|
||||
int ret;
|
||||
|
||||
label = ofnode_read_string(node, "label");
|
||||
if (!label) {
|
||||
debug("%s: node %s has no label\n", __func__,
|
||||
ofnode_get_name(node));
|
||||
return -EINVAL;
|
||||
}
|
||||
|
||||
ret = device_bind_driver_to_node(parent, "bcm6858-led",
|
||||
ofnode_get_name(node),
|
||||
node, &dev);
|
||||
if (ret)
|
||||
return ret;
|
||||
|
||||
uc_plat = dev_get_uclass_platdata(dev);
|
||||
uc_plat->label = label;
|
||||
}
|
||||
|
||||
return 0;
|
||||
}
|
||||
|
||||
static const struct udevice_id bcm6858_led_ids[] = {
|
||||
{ .compatible = "brcm,bcm6858-leds" },
|
||||
{ /* sentinel */ }
|
||||
};
|
||||
|
||||
U_BOOT_DRIVER(bcm6858_led) = {
|
||||
.name = "bcm6858-led",
|
||||
.id = UCLASS_LED,
|
||||
.of_match = bcm6858_led_ids,
|
||||
.bind = bcm6858_led_bind,
|
||||
.probe = bcm6858_led_probe,
|
||||
.priv_auto_alloc_size = sizeof(struct bcm6858_led_priv),
|
||||
.ops = &bcm6858_led_ops,
|
||||
};
|
||||
Loading…
Reference in New Issue