FIT header verification in mkimage was treating a return code as a boolean,
which meant that failures in validating the fit were seen as successes.
Additionally, mkimage was checking all formats to find a header which
passes validation, rather than using the image type specified to
mkimage.
checkpatch.pl checks for lines ending with '(' and alignment matching
open parentheses are ignored to keep with existing coding style.
Signed-off-by: Jordan Hand <jorhand@microsoft.com>
The syntax of dumpimage was simplified in commit 12b831879a ("tools:
dumpimage: Simplify arguments"), but the test
(test/image/test-imagetools.sh) was not updated and is now failing.
Update the test to use the new syntax.
Reported-by: Vagrant Cascadian <vagrant@debian.org>
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Tested-by: Vagrant Cascadian <vagrant@debian.org>
This pull request contains bugfixes for rcar_i2c, rcar_ii2c and
i2c_cdns driver.
Also the commit "i2c: rcar_i2c: Add Gen3 SoC support" from Marek
is a bugfix for arm64 builds, as discussed with Marek on list.
Cosmetic change. Any call to the recover function would need to do the
same check afterwards, so it's sensible to make it part of the function.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
It needs to be done for both reads and writes, so do it at rcar_i2c_xfer
to avoid duplication.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fix rcar_i2c_xfer return value, previously it was always returning
-EREMOTEIO when dealing with errors from calls to the read/write
functions.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Do the reset before clearing the MSR, otherwise it may result in a read
or write operation instead if the start condition is repeated.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Document the meaning of macros related to registers and values to be
written to them.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Setting up the delay only needs to be done once; move it to
rcar_i2c_set_speed so it's done at initialization time.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds support for handling arbitration lost
in case of multi master mode. When an arbitration lost
is detected, it retries for 10 times before failing.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The arbitration lost interrupt was not getting cleared
while clearing interrupts. This patch fixes this by adding
arbitration lost interrupt as well during clear. This patch
also removes hardcoded value and defined a macro for it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add support for R-Car Gen3 SoCs into the driver, which encompases
the Gen3 SoC extra timing register handling and 64bit build fixes.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Read ICSR only once to avoid missing interrupts. This happens on R8A7791
Porter during reset, when reading the PMIC register 0x13, which may fail
sometimes because of the missed DTE interrupt.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
This pull request contains only bug fixes.
The most notable bug fixed was writing to random memory addresses when
trying to add a HII package of a yet unsupported package type.
-----BEGIN PGP SIGNATURE-----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=HuZ2
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-04-rc4' of https://github.com/xypron2/u-boot
Pull request for the UEFI subsystem for v2019.04-rc4
This pull request contains only bug fixes.
The most notable bug fixed was writing to random memory addresses when
trying to add a HII package of a yet unsupported package type.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcfNQTAAoJEB6zHgIOrC/Iv6EH/3GGs0wbTSoXPyqpFkiFCH0p
niOGHK0KjS0/U9hhlAzPyD9pgm9nXhwEXxrwPTznOAFIPNI3gARdO2ofwAOL7hFR
ORsB3rWpoX/r2XOunHz7bExpTlXQnXZue0SFrWl4aatWTATb8zcbpp2l+8ljSXs+
/MFhyyqTogLq92t+4+ekwsTZkHvcDxeHGbnlBiQH0bcUw1vYs6AoYjAvC7duu/Y/
5ZL4lozJnMGCiFA5XZmqDkTwCSExt/Un8pEORUlwf7Rngwx37jdCeOgmKDR/WjOx
EFQxKTXotzYqJtQzCCT0NidI/2QG3PJHw2yx9Q7IsGFk97JYMq+gT4CyJj5Wgks=
=BIAO
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.04-a' of git://git.denx.de/u-boot-atmel
First set of u-boot-atmel fixes for 2019.04 cycle
- Enable DHCP as boot-source in distro boot for NXP layerscape
platforms
- fix register layout for SEC on Layerscape architectures
- fixes related to DPAA2 ethernet
Now the same SPI controller driver is reusable in all Allwinner
SoC variants, so rename the existing sun4i_spi.c into spi-sunxi.c
which eventually look like a common sunxi driver.
Also update the function, variable, structure names in driver from
sun4i into sunxi.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- drop unused macros.
- use base instead of base_addr, for better code readability
- move .probe and .ofdata_to_platdata functions in required
places to add platdata support in future.
- use sentinel sun4i_spi_ids.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
The usual SPI transmission protocol in Allwinner A10 and A31
controllers share similar context with minimal changes in register
offsets along with few additional register bits on A31.
So, add A31 spi controller support in existing sun4i_spi with A31
specific register offsets and bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLK support to enable AHB and MOD SPI clocks on sun4i_spi driver.
Clock disablement could be done while releasing the bus transfer, but
the existing code doesn't disable the clocks it only taken care of clock
enablement globally in probe.
So to make a proper clock handling, the clocks should enable it in claim
and disable it in release.
This patch would also do that change, by enable and disable clock in
proper order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Support fifo_depth via drvdata instead of macro definition, this would
eventually reduce another macro definition for new SPI controller fifo
depth support addition.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Allwinner support two different SPI controllers one for A10 and
another for A31 with minimal changes in register offsets and
respective register bits, but the logic for accessing the SPI
master via SPI slave remains nearly similar.
Add enum offsets for register set and register bits, so-that
it can access both classes of SPI controllers.
Assign same control register for global, transfer and fifo control
registers to make the same code compatible with A31 SPI controller.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Stefan Mavrodiev <stefan@olimex.com> # A20-SOM204
- Implement SPI AHB, MOD clocks via ccu_clk_gate for all
supported Allwinner SoCs
- Implement SPI resets via ccu_reset for all supported
Allwinner SoCs.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
To drain rx fifo the fifo need to poll for how much data has
been filled up in rx fifo.
To achieve this, the current code is using wait_for_bit logic
on control register with exchange burst mode mask, which is not
a proper way of waiting for fifo filled up.
So, add code for polling rxfifo to be filled up using fifo
status register.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
With current order of include files, the file designware_spi.c
can't see that the struct global_data has the member
board_type when CONFIG_BOARD_TYPES is defined. By not seeing this
then all the members are shifted in the struct global_data.
So when the driver is trying to read from device tree blob, it
would pass the wrong address to the function 'fdtdev_get_int'.
This will make to use the default frequency 500000.
The fix consists of changing the order of include files in
designware_spi.c to include first common.h file.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
SPL_GENERATE_ATMEL_PMECC_HEADER will generate a header for the SPL for NAND
information. The initial stage 1 bootloader will use this header in case the
NAND flash doesn't support commands to retrieve sector size, etc.
However this header is bad for different boot media, like MMC or SPI.
In case SD_BOOT or SPI_BOOT is used, remove the config for this.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
This was already set for 'sama5d27_som1_ek_mmc_defconfig' (first SD
card, full size). Without this option set, the MAC address is not read
from the I²C EEPROM at boot, and remains unset:
U-Boot 2019.01 (Jan 01 2019 - 00:00:00 +0000)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
DRAM: 128 MiB
MMC: sdio-host@a0000000: 0, sdio-host@b0000000: 1
Loading Environment from FAT... OK
In: serial
Out: serial
Err: serial
Net:
Error: ethernet@f8008000 address not set.
eth-1: ethernet@f8008000
Hit any key to stop autoboot: 0
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Since the datasheet Rev.1.00 has an error about the USB ID pin name,
this patch revises it.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Errata for Rev 1.50,
the MOD_SEL0 bit3 is set to 0 when TX0_A pin function is selected,
and the MOD_SEL0 bit3 is set to 1 when TX0_B pin function is
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Rev.1.50, the MOD_SEL0
bit16 is set to 0 when NFALE_A and NFRB_N_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
According to the R-Car Gen3 Hardware Manual Rev 1.50, the MOD_SEL0
bit2 is set when RX2_{A,B}, TX2_{A,B} and SCK2_A pin functions are
selected.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes the allocation name "RTSx_N_TANS_x" of IPSR /
MOD_SEL0/1 of r8a77990 to "RTSx_N_x". This information was
confirmed in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes the allocation name "sel_ndfc" of MOD_SEL2[22]
of r8a7796 / r8a77965 to "sel_ndf". This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch removes CC5_OSCOUT assignment of IP17[3:0] of r8a7795
/ r8a7796 / r8a77965. This information was confirmed in the R-Car
Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes to the correct names, and "_" is not include after
"adg" for r8a7795/r8a7796/r8a77965. This information was confirmed
in the R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch is change the bit assignment of "HDMI1_CEC" to "GP7_03",
and "HDMI0_CEC" to "GP7_02". This information was confirmed in the
R-Car Gen3 Hardware Manual Rev.1.50.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
sec_firmware reserves JR3 for it's own usage and deletes the JR3 node
from the device tree. This causes this warning to be issued when doing
the device tree fixup:
WARNING could not find node fsl,sec-v4.0-job-ring: FDT_ERR_NOTFOUND.
Fix it by excluding the device tree fixup for the JR reserved by
sec_firmware.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The SEC QI ICID setup in the QIIC_LS register is actually an offset
that is being added to the ICID coming from the qman portal. Setting
it with a non-zero value breaks SMMU setup as the resulting ICID is
not known. On top of that, the SEC QI ICID must match the qman portal
ICIDs in order to share the isolation context.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
On Layerscape architectures the SEC memory map is 1MB and the
register blocks contained in it are 64KB aligned, not 4KB as
the ccsr_sec structure currently assumes. Fix the layout of
the structure for these architectures.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
dhcp boot is a useful feature and works out-of-the-box on these
platforms. Enable it as a boot source.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
EFI applications need bounce buffers to work properly on these
platforms.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Default environment variable is more complete. Also scans for efi
binaries for example.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
