This fixes the following compiler warning:
"warning: cast from pointer to integer of different size
[-Wpointer-to-int-cast]"
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no reason to specify header with full soc name.
Symlink is setup automatically (arch -> arch-zynqmp)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The xhci wrapper-driver for Rockchip searches the DTS to find its
child node compatbile with 'rockchip,rk3399-usb3-phy' to retrieve the
base-address of the PHY. However, this is currently broken (and
always has been), returning NULL. However, the (wrongly) retrieved
base-address is never used.
We thus remove this code for now.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
In xhci_set_configuration(), 'Context Entries' field in the slot
context was cleared with mask LAST_CTX_MASK, but it should have
taken the endianness into consideration.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
If a full speed hub connects to a high speed hub which supports MTT,
the MTT field of its slot context will be set to 1 when xHCI driver
setups an xHCI virtual device in xhci_setup_addressable_virt_dev().
Once usb core fetch its hub descriptor, and need to update the xHC's
internal data structures for the device, the HUB field of its slot
context will be set to 1 too, meanwhile MTT is also set before, this
will cause configure endpoint command fail. In the case, we should
clear MTT to 0 for full speed hub according to section 6.2.2.
This keeps in sync with Linux kernel commit:
096b110: usb: xhci: fix config fail of FS hub behind a HS hub with MTT
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Per xHCI spec chapter 6.2.2 table 6-7, as input, software shall
initialize the dev_state field to '0'. Though this does not seem
to cause any issue with most xHC implementations, let's do this
to conform with the spec.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
If a USB 3.0 hub is plugged into the root port of the xHC, the xHCI
driver will issue a 'Configure Endpoint' command to the xHC for it
to update its internal data structure for this hub device. The hub
attributes are in the slot context so we need tell xHC to update the
slot context by setting the add context flags of the input control
context to only cover the slot context.
At present the add context flags is or'ed with the slot context bit,
but it should really be accurately set to the slot context, as the
variable that holds the value of the add context flags comes from
whatever was set in the last command execution, which may contain
additional contexts that 'Configure Endpoint' command should not
touch. Some xHC implementations like x86 don't complain such, but
it was observed on Renesas RCar Gen3 platform that the RCar xHC
complains with a 'TRB error' completion codes as the response.
Reported-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Marek Vasut <marek.vasut@gmail.com>
Tested-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
During the execution of xhci_deregister xHCI registers are accessed. If
the clock is already deactivated when xhci_deregister is called this can
lead to undefined behavior. Change the order to deregister the device
before deactivating the clock.
Signed-off-by: Matthias Blankertz <matthias.blankertz@cetitec.com>
Allwinner USB PHY handling can be done through driver-model
generic-phy so add the generic-phy ops to relevant places
on host and musb sunxi driver and enable them in respective
SOC's.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Move struct sunxi_ccm_reg pointer to private structure
so-that accessing ccm reg base become more proper way
and avoid local initialization in each function.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jun Nie <jun.nie@linaro.org>
Switch to DM_USB was done and there is no need to keep !DM_USB code in
tree.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Putting zero length array at the end of struct is a common technique
to embed arbitrary length of members. There is no good reason to let
regmap_alloc_count() branch by "if (count <= 1)".
As far as I understood the code, regmap->base is an alias of
regmap->ranges[0].start, but it is not helpful but make the code
just ugly.
Rename regmap_alloc_count() to regmap_alloc() because the _count
suffix seems pointless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: fixup cpu_info-rcar.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
When no PHYs are declared in the dwc3 node, the phy init fails.
This patch checks if the "phys" property is presend and reports
the error returned by dev_count_phandle_with_args().
This patchs also fixes the styles issues added in last commit.
This patch should fix the DWC3 support on the UniPhier SoC family.
Fixes: 7c839ea70c ("usb: host: dwc3: Add support for multiple PHYs")
Reported-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The disabled clk API returns -ENOSYS unlike the reset API returning -ENOTSUPP.
Fixes: ca7fdc8b12 ("usb: host: Add simple of glue driver for DWC3 USB Controllers integration")
Reported-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
DWC3 Ips can have more than 1 PHY for USB2 and 1 PHY for USB3, add support
for a generic number of PHYs and adapt the code to handle a generic
number of PHYs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is a port of the dwc3-of-simple driver from Linux to enable/deassert
clock and resets of a simple DWC3 Controller HW glue.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This patch increases timeout to 2s.
It was seen on 2 USB devices (Verbatim STORE N GO 070B4AED0FB22358 and
USB DISK 2.0 9000729BA41DDF40) that the request sense command takes
between 1.3s and and 1.5s.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This patch adds an interface to disable the power in dwc2 driver.
This new interface is called when the device is removed.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add generic_phy_power_on() and generic_phy_power_off()
calls to switch ON/OFF phy during probe and remove functions.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Factorize PHY get/init/poweron and PHY poweroff/exit operations
into separate function, it simplify the error path.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
ppc4xx support was removed some time ago. Lets remove the now unused
EHCI driver and all its references for this platform as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Marek Vasut <marex@denx.de>
DWC3 USB3 controllers will need USB3 PHY to be enabled, in addition to
USB2 PHY, to be functional. Therefore enable USB3 PHY when available.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Refractor PHY get/init/poweron and PHY poweroff/exit operations into
separate function so that its easy to support multiple PHYs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
It is wrong that expect .phy_init() to also power on the PHY. Therefore,
explicitly, call generic_phy_power_on() after generic_phy_power_init() in
order to power on PHY before using it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If we use hardware with very small RAM (let's consider just a couple
of hundreds of kB but not megabytes) it is not super convenient to lose
64kB for statically allocated bufer which most probably won't be used
as big as it is. Typically we'll have much shorter data packages to
excahnge and in the worst case longer packets will be split on separate
transactions.
For those corner-cases user will be able to set his buffer size of
choice via USB_DWC2_BUFFER_SIZE option in menuconfig.
By default we'll use 64 kB as it was hard-coeded before so existing
users shouldn't be affected at all.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
For some reason from day one we used to have both CONFIG_DWC2_UTMI_WIDTH
mentioned in dwc2.h and in scripts/config_whitelist.txt but never really used
and CONFIG_DWC2_UTMI_PHY_WIDTH used in real code in dwc2.c (but never
defined).
Moreover even though CONFIG_DWC2_UTMI_WIDTH might be either 8 or 16
depending on hardware (and the same is said in a comment for it in
dwc2.h) but then 8 is hardcoded in the header leaving no ability to
override this value in board's configuration.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
The variable hcd_name is unsued, drop.
Cc: Marek Vasut <marex@denx.de>
Cc: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
ehci_writel() swaps the arguments for address and value. One call
in ehci-mxs ignores that.
This fixes the warning:
drivers/usb/host/ehci-mxs.c: In function ?ehci_hcd_stop?:
drivers/usb/host/ehci-mxs.c:159:19: error: initialization makes integer from pointer without a cast [-Werror=int-conversion]
ehci_writel(tmp, &hcor->or_usbcmd);
^
arch/arm/include/asm/io.h:117:34: note: in definition of macro ?writel?
#define writel(v,c) ({ u32 __v = v; __iowmb(); __arch_putl(__v,c); __v; })
^
drivers/usb/host/ehci-mxs.c:159:2: note: in expansion of macro ?ehci_writel?
^~~~~~~~~~~
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Bool initializations should use true and false.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
When enable CONFIG_HAS_FSL_DR_USB, we might encounter below compile
warning, apply this patch can fix it:
drivers/usb/host/ehci-fsl.c:109:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
((u32)hccr + HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
^
drivers/usb/host/ehci-fsl.c:108:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
hcor = (struct ehci_hcor *)
^
drivers/usb/host/ehci-fsl.c:115:8: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
drivers/usb/host/ehci-fsl.c:115:19: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
(u32)hccr, (u32)hcor,
^
include/log.h:131:26: note: in definition of macro 'debug_cond'
printf(pr_fmt(fmt), ##args); \
^~~~
drivers/usb/host/ehci-fsl.c:114:2: note: in expansion of macro 'debug'
debug("ehci-fsl: init hccr %x and hcor %x hc_length %d\n",
^~~~~
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
While the USB HW in the RZ/A is basically the same, there are some
differences from the original versions that were in the SH SoCs.
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Its a valid use case to call ehci_submit_async() with a NULL buffer
with length 0. E.g. from usb_set_configuration().
As invalidate_dcache_range() isn't able to judge if the address
NULL is valid or not (depending on the SoC hardware configuration it
might be valid) do the check in ehci_submit_async() as here we know
that we don't have to invalidate such a buffer.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Currently we check in ehci_shutdown() if ctrl is NULL after
dereferencing it.
Before this we have already dereferenced ctrl, ctrl->hccr,
and ctrl->hcor in ehci_get_portsc_register(), ehci_submit_root(),
and hci_common_init().
A better approach is to already check ctrl, ctrl->hccr, and ctrl->hcor
during the initialization in ehci_register() and usb_lowlevel_init()
and signal an error here via the return code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add firmware V3, firmware loader and XHCI glue for the Renesas R-Car
Gen3 SoCs XHCI controller. Thus far only the R-Car Gen3 R8A7795 ES2.0+
and R8A7796 are supported.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Commit 9000eddbae ("drivers/usb/ehci: Use platform-specific accessors")
broke USB 2.0 on big-endian platforms because for them writel/readl()
does automatic conversion of BE data to LE.
Proper implementation requires to use "raw" variant of these accessors
which read/write data without messing with endianess.
While at it replace cpu_to_be32() to be32_to_cpu() in readl() to
keep sane semantics.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Marek Vasut <marex@denx.de>
Reported-by: Vladimir Boroda <boroda@yahoo.com>
This makes the initial changes need to support the
a38x series of SOCs. It adds the device-tree identifier
as well as changing the board_support function to take
the IO address designated by device-tree.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
[baruch: use fdt_addr_t; update 37xx and 8K implementations]
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
use Kconfig to select xhci accordingly.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
U-Boot widely uses error() as a bit noisier variant of printf().
This macro causes name conflict with the following line in
include/linux/compiler-gcc.h:
# define __compiletime_error(message) __attribute__((error(message)))
This prevents us from using __compiletime_error(), and makes it
difficult to fully sync BUILD_BUG macros with Linux. (Notice
Linux's BUILD_BUG_ON_MSG is implemented by using compiletime_assert().)
Let's convert error() into now treewide-available pr_err().
Done with the help of Coccinelle, excluing tools/ directory.
The semantic patch I used is as follows:
// <smpl>
@@@@
-error
+pr_err
(...)
// </smpl>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Re-run Coccinelle]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since we use EHCI generic driver on RCar Gen3 , this driver is useless.
Remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The 'Max Burst Size' indicates to the xHC the maximum number of
consecutive USB transactions that should be executed per scheduling
opportunity. This is a “zero-based” value, where 0 to 15 represents
burst sizes of 1 to 16, but at present this is always set to zero.
Let's program the required value according to real needs.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
USB endpoint reports the period between consecutive requests to send
or receive data as bInverval in its endpoint descriptor. So far this
is ignored by xHCI driver and the 'Interval' field in xHC's endpoint
context is always programmed to zero which means 1ms for low speed
or full speed , or 125us for high speed or super speed. We should
honor the interval by getting it from endpoint descriptor.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
In xhci_check_maxpacket(), the control endpoint 0 max packet size
is wrongly taken from the interface's endpoint descriptor. However
the default endpoint 0 does not come with an endpoint descriptor
hence is not included in the interface structure. Change to use
epmaxpacketin[0] instead.
The other bug in this routine is that when setting max packet size
to the xHC endpoint 0 context, it does not clear its previous value
at all before programming a new one.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
xHCI uses normal TRBs for both bulk and interrupt. This adds the
missing interrupt transfer support to xHCI so that devices like
USB keyboard that uses interrupt transfer can work.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present xHCI driver assumes LS/FS devices are attached directly
to a HS hub. If they are connected to a LS/FS hub, the driver will
fail to perform the USB enumeration process on such devices.
This is fixed by looking from the device itself all the way up to
the HS hub where the TT that serves the device is located.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
With the root hub unbinding in usb_stop(), there is no need to do
a Sandbox-specific reset operation. usb_emul_reset() is no longer
used anywhere, drop it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present we only do device_remove() during usb stop. The DM API
device_remove() only marks the device state as inactivated, but
still keeps its USB topology (eg: parent, children, etc) in the DM
device structure. There is no issue if we only start USB subsystem
once and never stop it. But a big issue occurs when we do 'usb stop'
and 'usb start' multiple times.
Strange things may be observed with current implementation, like:
- the enumeration may report only 1 mass storage device is detected,
but the total number of USB devices is correct.
- USB keyboard does not work anymore after a bunch of 'usb reset'
even if 'usb tree' shows it is correctly identified.
- read/write flash drive via 'fatload usb' may complain "Bad device"
In fact, every time when USB host controller starts the enumeration
process, it takes random time for each USB port to show up online,
hence each USB device may appear in a different order from previous
enumeration, and gets assigned to a totally different USB address.
As a result, we end up using a stale USB topology in the DM device
structure which still reflects the previous enumeration result, and
it may create an exact same DM device name like generic_bus_0_dev_7
that is already in the DM device structure. And since the DM device
structure is there, there is no device_bind() call to bind driver to
the device during current enumeration process, eventually creating
an inconsistent software representation of the hardware topology, a
non-working USB subsystem.
The fix is to clear the unused USB topology in the usb_stop(), by
calling device_unbind() on each controller's root hub device, and
the unbinding will unbind all of its children automatically.
For Sandbox, we need scan the device tree each time when we start
the USB stack, in order to re-create the emulated USB devices and
bind drivers for them before we actually do the driver probe.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Current emulator select logic in usb_emul_find_devnum() is to test
the USB address. The USB address of the device being enumerated is
initialized to zero at the beginning of the enumeration process in
usb_setup_device(). At this point, the saved USB address in the
platform data has not been assigned to any valid USB address either.
This means: the logic will select an emulator device according to
its sequence of declaring order in the device tree. Take test.dts
for example, flash-stick@0 will be selected before flash-stick@1.
But unfortunately such logic is wrong.
In fact USB devices show up in a random order during the enumeration
which means usb_emul_find_devnum() may be called on port 3 for keyb@3
before on port 0 for flash-stick@0.
To fix this, we introduce a new emulator uclass specific platdata
to store the USB device's port number on its parent hub, and update
the logic to test the port number instead.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
At present 'usb tree' shows that the root hub on the Sandbox USB
controller is at full speed. But its device descriptor says it's
USB 2.0, so let's report it as a high speed device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
EHCD can handle any transfer length as long as there is enough free
heap space left, hence set the theoretical max number SIZE_MAX.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
xHCD allocates one segment which includes 64 TRBs for each endpoint
and the last TRB in this segment is configured as a link TRB to form
a TRB ring. Each TRB can transfer up to 64K bytes, however data
buffers referenced by transfer TRBs shall not span 64KB boundaries.
Hence the maximum number of TRBs we can use in one transfer is 62.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The HCD may have limitation on the maximum bytes to be transferred
in a USB transfer. USB class driver needs to be aware of this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
The Linux kernel driver sets the number of event segments and entries
to 1 , while the initial import of the xhci code set that values to 3
for reasons unknown. While most controllers are fine with more event
segments with more entries, there are standard-conformant controllers
(ie. Renesas RCar xHCI) which only support 1 event segment.
Set the number of event segments and event entries back to 1 to allow
such controllers to work with U-Boot xHCI stack. Note that the Renesas
controller correctly indicates ERST Max = 1 in HCSPARAMS2[7:4] .
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
This patch adds the ST glue logic to manage the DWC3 HC
on STiH407 SoC family. It configures the internal glue
logic and syscfg registers.
Part of this code been extracted from kernel.org driver
(drivers/usb/dwc3/dwc3-st.c)
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We are now using an env_ prefix for environment functions. Rename these
two functions for consistency. Also add function comments in common.h.
Quite a few places use getenv() in a condition context, provoking a
warning from checkpatch. These are fixed up in this patch also.
Suggested-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Fix following warnings encountered with platforms
dra7xx_evm and dra7xx_hs_evm :
arm: + dra7xx_evm
+ hccr = (struct xhci_hccr *)devfdt_get_addr(dev);
+ ^
+ hcor = (struct xhci_hcor *)((phys_addr_t)hccr +
+ ^
w+drivers/usb/host/xhci-dwc3.c: In function 'xhci_dwc3_probe':
w+drivers/usb/host/xhci-dwc3.c:124:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
w+drivers/usb/host/xhci-dwc3.c:125:30: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
w+drivers/usb/host/xhci-dwc3.c:125:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
arm: + dra7xx_hs_evm
+ hccr = (struct xhci_hccr *)devfdt_get_addr(dev);
+ ^
+ hcor = (struct xhci_hcor *)((phys_addr_t)hccr +
+ ^
w+drivers/usb/host/xhci-dwc3.c: In function 'xhci_dwc3_probe':
w+drivers/usb/host/xhci-dwc3.c:124:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
w+drivers/usb/host/xhci-dwc3.c:125:30: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
w+drivers/usb/host/xhci-dwc3.c:125:9: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Introduced by 7e65e84 usb: host: xhci-dwc3: Convert driver to DM
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Call generic_phy_init() only when a PHY was found.
This will avoid a crash if no "phys" property is found in DT.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Patrick Delaunay <patrick.delaunay@st.com>
Call generic_phy_init() only when a PHY was found.
This will avoid a crash if no "phys" property is found in DT.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Patrick Delaunay <patrick.delaunay@st.com>
Add CONFIG_DM_USB flag to avoid following compilation errors
detected by buildman :
+drivers/usb/host/built-in.o: In function `xhci_dwc3_remove':
+drivers/usb/host/xhci-dwc3.c:168: undefined reference to `xhci_deregister'
+drivers/usb/host/built-in.o: In function `xhci_dwc3_probe':
+drivers/usb/host/xhci-dwc3.c:145: undefined reference to `usb_get_dr_mode'
+drivers/usb/host/xhci-dwc3.c:152: undefined reference to `xhci_register'
introduced by patch d5c3f014da3 "usb: host: xhci-dwc3: Convert driver to DM"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reported-by: Ran Wang <ran.wang_1@nxp.com>
So far LS/FS devices directly attached to xHC root port can be
successfully enumerated by xHCI driver, but if they are connected
behind a hub, the enumeration process fails to address the device.
It turns out xHCI driver still misses a part that in the device's
input slot context, all Transaction Translator (TT) related fields
are not programmed. The xHCI spec defines how to enable TT.
Now LS/FS devices like USB keyboard/mouse can be enumerated behind
a high speed hub.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no way to know whether the attached device is a hub or
not in advance before the device's descriptor is fetched. But
once we know it's a high speed hub, per the xHCI spec, we need
to tell xHC it's a hub device by initializing hub-related fields
in the input slot context.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For USB host controllers like xHC, its internal representation of
hub needs to be updated after the hub descriptor is fetched. This
adds a new op that does this.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
xHCI spec says: the values of the 'route string' field shall be
initialized by the first 'Address Device' command issued to a
device slot, and shall not be modified by any other command.
So far U-Boot does not program this field, and it does not prevent
SS device directly attached to root port, or HS device behind an HS
hub, from working, due to the fact that 'route string' is used by
the xHC to target SS packets. But in order to enumerate devices
behind an SS hub, this field must be programmed.
With this commit and along with previous commits, now SS & HS devices
attached to a USB 3.0 hub can be enumerated by U-Boot.
As usual, this new feature is only available when DM is on.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For future extension, change xhci_setup_addressable_virt_dev()
signature to accept a pointer to 'struct usb_device', instead
of its members slot_id & speed, as the struct already contains
these two plus some other useful information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sometimes we need know if a given hub device is root hub or not.
Add a new API to test this. This removes the xHCI driver's own
version is_root_hub() and change to use the new API.
While we are here, remove the unused/commented out get_usb_device()
in the xHCI driver too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Use USB hub device's dev->uclass_priv to point to 'usb_hub_device'
so that with driver model usb_hub_reset() and usb_hub_allocate()
are no longer needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As there is no board that currently uses xhci-pci driver without DM
USB, drop its support and leave only DM support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add CONFIG_USB_XHCI_PCI as a Kconfig option.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
EHC reports supported maximum number of ports in the HCSPARAMS
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
xHC reports supported maximum number of ports in the HCSPARAMS1
register, so it's unnecessary to use a hardcoded config option
CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
HCSPARAMS1:MaxPorts field specifies the maximum port number value,
and its valid values are in the range of 1 to 255.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
USB 3.0 hubs have a slightly different hub descriptor than USB 2.0
hubs, with a fixed (rather than variable length) size. Change the
host controller drivers that access those last two fields
(DeviceRemovable and PortPowerCtrlMask) to use the union.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
Testing a USB 3.0 hub by connecting it to the xHCI port on Intel
MinnowMax, when issuing 'get hub descriptor' to the hub, xHCI
reports a transfer event TRB with a completion code 6 which means
'Stall Error'.
In fact super speed USB hub descriptor type is 0x2a, not 0x29.
Sending correct SETUP packet to the hub makes it not stall anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
A valid input slot context for a 'configure endpoint' command requires
the 'Context Entries' field to be initialized to the index of the last
valid endpoint context that is defined by the target configuration. We
set up the 'Context Entries' field, but we forget to include the input
slot context in the input control context 'Add Context flags' bitmap.
So xHC will simply ignore input slot context and continue using its own
which contains old information of the device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
The scratchpad buffer array is used to define the locations of
statically allocated memory pages that are available for the
private use of the xHC. The xHCI spec explicitly mentions that
system software shall allocate the scratchpad buffers before
placing the xHC in to Run mode (Run/Stop (R/S) = ‘1’), however
U-Boot is missing this part.
This causes xHC on Intel platform does not respond the very first
'enable slot' command that is given to xHC and the 'enable slot'
command completion event TRB is never generated and xHC seems to
hang forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
In xhci_queue_command(), when the command is not 'reset endpoint',
'stop endpoint' or 'set TR dequeue pointer', endpoint ID should not
be encoded in the TRB.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
There is no member called 'dma' in struct xhci_container_ctx. Remove
the comments that mentions it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Stefan Roese <sr@denx.de>
use array to save deasserted resets reference in order to
assert them in case of error during probe() or during driver
removal.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
use array to save enabled clocks reference in order to
disabled them in case of error during probe() or during
driver removal.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use an array to save enabled clocks reference and deasserted resets
in order to respectively disabled and asserted them in case of error
during probe() or during driver removal.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
this allows to get file, line and function location
of the current error message.
Signed-off-by: patrice chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support of generic PHY framework support
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
DWC3 dual role mode is selected using DT "dr_mode"
property. If not found, DWC3 controller is configured
in HOST mode by default
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add Driver Model support with use of generic DT
compatible string "snps,dwc3"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Update the Tegra EHCI driver to support a live device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
Adjust this to take a device as a parameter instead of a node.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Beaver, Jetson-TK1
Tested-by: Stephen Warren <swarren@nvidia.com>
Change is consistent with other SOCs and it is in preparation
for adding SOMs. SOC's related files are moved from cpu/ to
mach-imx/<SOC>.
This change is also coherent with the structure in kernel.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@nxp.com>
CC: Akshay Bhat <akshaybhat@timesys.com>
CC: Ken Lin <Ken.Lin@advantech.com.tw>
CC: Marek Vasut <marek.vasut@gmail.com>
CC: Heiko Schocher <hs@denx.de>
CC: "Sébastien Szymanski" <sebastien.szymanski@armadeus.com>
CC: Christian Gmeiner <christian.gmeiner@gmail.com>
CC: Stefan Roese <sr@denx.de>
CC: Patrick Bruenn <p.bruenn@beckhoff.com>
CC: Troy Kisky <troy.kisky@boundarydevices.com>
CC: Nikita Kiryanov <nikita@compulab.co.il>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: "Eric Bénard" <eric@eukrea.com>
CC: Jagan Teki <jagan@amarulasolutions.com>
CC: Ye Li <ye.li@nxp.com>
CC: Peng Fan <peng.fan@nxp.com>
CC: Adrian Alonso <adrian.alonso@nxp.com>
CC: Alison Wang <b18965@freescale.com>
CC: Tim Harvey <tharvey@gateworks.com>
CC: Martin Donnelly <martin.donnelly@ge.com>
CC: Marcin Niestroj <m.niestroj@grinn-global.com>
CC: Lukasz Majewski <lukma@denx.de>
CC: Adam Ford <aford173@gmail.com>
CC: "Albert ARIBAUD (3ADEV)" <albert.aribaud@3adev.fr>
CC: Boris Brezillon <boris.brezillon@free-electrons.com>
CC: Soeren Moch <smoch@web.de>
CC: Richard Hu <richard.hu@technexion.com>
CC: Wig Cheng <wig.cheng@technexion.com>
CC: Vanessa Maegima <vanessa.maegima@nxp.com>
CC: Max Krummenacher <max.krummenacher@toradex.com>
CC: Stefan Agner <stefan.agner@toradex.com>
CC: Markus Niebel <Markus.Niebel@tq-group.com>
CC: Breno Lima <breno.lima@nxp.com>
CC: Francesco Montefoschi <francesco.montefoschi@udoo.org>
CC: Jaehoon Chung <jh80.chung@samsung.com>
CC: Scott Wood <oss@buserror.net>
CC: Joe Hershberger <joe.hershberger@ni.com>
CC: Anatolij Gustschin <agust@denx.de>
CC: Simon Glass <sjg@chromium.org>
CC: "Andrew F. Davis" <afd@ti.com>
CC: "Łukasz Majewski" <l.majewski@samsung.com>
CC: Patrice Chotard <patrice.chotard@st.com>
CC: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Masahiro Yamada <yamada.masahiro@socionext.com>
CC: Stephen Warren <swarren@nvidia.com>
CC: Andre Przywara <andre.przywara@arm.com>
CC: "Álvaro Fernández Rojas" <noltari@gmail.com>
CC: York Sun <york.sun@nxp.com>
CC: Xiaoliang Yang <xiaoliang.yang@nxp.com>
CC: Chen-Yu Tsai <wens@csie.org>
CC: George McCollister <george.mccollister@gmail.com>
CC: Sven Ebenfeld <sven.ebenfeld@gmail.com>
CC: Filip Brozovic <fbrozovic@gmail.com>
CC: Petr Kulhavy <brain@jikos.cz>
CC: Eric Nelson <eric@nelint.com>
CC: Bai Ping <ping.bai@nxp.com>
CC: Anson Huang <Anson.Huang@nxp.com>
CC: Sanchayan Maity <maitysanchayan@gmail.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Patrick Delaunay <patrick.delaunay@st.com>
CC: Gary Bisson <gary.bisson@boundarydevices.com>
CC: Alexander Graf <agraf@suse.de>
CC: u-boot@lists.denx.de
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Use dev_read_bool() instead of fdt_getprop() to get the property
from DTS. And add a comment for "hnp-srp-disable" property to
fully describe its effect.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change migrates the USB_DWC2 configuration item to Kconfig
and runs moveconfig to adjust header files and defconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Split off into a separate patch:
Ran moveconfig to migrate other boards:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use fixed regulator to control the voltage of vbus. Enable vbus
supply when usb start and disable vbus supply when usb stop.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The xhci-rockchip driver depends on DM_REGULATOR and DM_USB.
So add dependent features for xhci-rockchip driver in Kconfig.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This change covers the USB3 (xhci) driver for the Rockchip devices.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Current implementation doesn't allow utilization of platform-specific
reads and writes.
But some arches or platforms may want to use their accessors that do
some extra work like adding barriers for data serialization etc.
Interesting enough OHCI accessors already do that so just aligning
EHCI to it now.
This is a resend of http://patchwork.ozlabs.org/patch/726714/
Back in the day this patch broke some PPC and Sandbox boards
as they we missing inclusion of "asm/io.h". Those missing items were
fixed with:
1) http://patchwork.ozlabs.org/patch/751397/
2) http://patchwork.ozlabs.org/patch/771099/
So now it should be safe to apply this patch.
FWIW TravisCI builds everything with all 3 patches in place,
see https://travis-ci.org/abrodkin/u-boot/builds/239563813
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
In current code, after running the command of "usb start", the controller
will keep in otg mode and can't switch to host mode if not support
SNP/SRP capability. So add the property of "hnp-srp-disable" in the DTS
to config the contrller work in force mode of host.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add the compatible "rockchip,rk3328-xhci" in match table
for rk3328 to probe xhci controller. Use fixed regulator
to control the voltage of vbus and turn off vbus when
usb stop.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rather than relying on common.h to provide this include, which is going
away at some point, include it explicitly in each file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
We used to have opencoded ehci_readl()/writel() which required no
external functions to be called.
Now with attempt to switch to generic readl()/writel() accessors
we see a missing declaration of those accessors in ehci-ppc4xx.
Something like that happens if applied
http://patchwork.ozlabs.org/patch/726714/:
--------------------------------->8---------------------------
CC drivers/usb/host/ehci-pci.o
In file included from drivers/usb/host/ehci-pci.c:14:0:
drivers/usb/host/ehci-pci.c: In function 'ehci_pci_init':
drivers/usb/host/ehci.h:108:36: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
#define ehci_readl(x) cpu_to_le32(readl(x))
^
drivers/usb/host/ehci.h:23:26: note: in definition of macro 'HC_LENGTH'
#define HC_LENGTH(p) (((p) >> 0) & 0x00ff)
^
include/linux/byteorder/generic.h:89:21: note: in expansion of macro '__cpu_to_le32'
#define cpu_to_le32 __cpu_to_le32
^~~~~~~~~~~~~
drivers/usb/host/ehci-pci.c:33:14: note: in expansion of macro 'ehci_readl'
HC_LENGTH(ehci_readl(&hccr->cr_capbase)));
^~~~~~~~~~
--------------------------------->8---------------------------
This the same fix as we have for "ehci-ppc4xx" in
83cb46c286 "ehci-ppc4xx: Prepare for usage of readl()/writel() accessors".
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Add support for requesting GPIOs with a live device tree.
This involves adjusting the function signature for the legacy function
gpio_request_by_name_nodev(), so fix up all callers.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes to stm32f746-disco.c:
Signed-off-by: Tom Rini <trini@konsulko.com>
The of_ prefix conflicts with the livetree version of this function.
Rename it to avoid problems when we add livetree support.
Signed-off-by: Simon Glass <sjg@chromium.org>
These support the flat device tree. We want to use the dev_read_..()
prefix for functions that support both flat tree and live tree. So rename
the existing functions to avoid confusion.
In the end we will have:
1. dev_read_addr...() - works on devices, supports flat/live tree
2. devfdt_get_addr...() - current functions, flat tree only
3. of_get_address() etc. - new functions, live tree only
All drivers will be written to use 1. That function will in turn call
either 2 or 3 depending on whether the flat or live tree is in use.
Note this involves changing some dead code - the imx_lpi2c.c file.
Signed-off-by: Simon Glass <sjg@chromium.org>
LS2081ARDB board is similar to LS2080ARDB board with few differences
It hosts LS2081A SoC
Default boot source is QSPI-boot
It does not have IFC interface
RTC and QSPI flash device are different
It provides QIXIS access via I2C
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Signed-off-by: Santan Kumar <santan.kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a USB controller driver for the EHCI block in R8A7795/R8A7796 SoC.
This is a stopgap measure until we have proper DT support, clock and
reset framework in place, at which point we can switch to ehci-generic.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Follow the exiting logic for the i.MX options when migrating this
option.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The following options are migrated over fully now:
- USB_EHCI_ATMEL
- USB_EHCI_MARVELL
- USB_EHCI_MX6
- USB_EHCI_MX7
- USB_EHCI_MSM
- USB_EHCI_ZYNQ
- USB_EHCI_GENERIC
This also requires fixing the depends on USB_EHCI_MARVELL as it's used
by Orion5X and Kirkwood as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Migrate the rest of the users of CONFIG_USB_EHCI_HCD over to Kconfig.
For a few SoCs, imply or default y this if USB is enabled. In some
cases we had not already migrated to CONFIG_USB so do that as well.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
In order to be able to migrate the various SoC EHCI CONFIG options we
first need to finish the switch from CONFIG_USB_EHCI to
CONFIG_USB_EHCI_HCD.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.
Modifications:
* Enable USB clocks in the OMAP version of the function
board_usb_init.
* Disable USB clocks in the OMAP version of the function
board_usb_cleanup.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c
To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
omap_xhci_board_usb_init.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
omap_xhci_board_usb_cleanup.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Modify the determination of the base address of xHCI registers of DRA7XX
targets.
Before the commit: by the target.
After the commit: by the USB port index.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Roger Quadros <rogerq@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
We used to have opencoded ehci_readl()/writel() which required no
external functions to be called.
Now with attempt to switch to generic readl()/writel() accessors
we see a missing declaration of those accessors in ehci-ppc4xx.
Something like that happens if applied
http://patchwork.ozlabs.org/patch/726714/:
---------------->8---------------
CC drivers/usb/host/ehci-ppc4xx.o
drivers/usb/host/ehci-ppc4xx.c: In function 'ehci_hcd_init':
drivers/usb/host/ehci-ppc4xx.c:23:3: warning: implicit declaration of function 'readl' [-Wimplicit-function-declaration]
HC_LENGTH(ehci_readl(&(*hccr)->cr_capbase)));
^
---------------->8---------------
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
We should invalidate the dcache before starting the DMA. In case there are
any dirty lines from the DMA buffer in the cache, subsequent cache-line
replacements may corrupt the buffer in memory while the DMA is still going on.
Cache-line replacement can happen if the CPU tries to bring some other memory
locations into the cache while the DMA is going on.
Signed-off-by: Eddie Cai <eddie.cai.linux@gmail.com>
Reviewed-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Some board do not use the dwc2 internal VBUS_DRV signal, but
use a gpio pin to enable the 5.0V VBUS power, add interface to
enable the power in dwc2 driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This patch adds the flags parameter to device_remove() and changes all
calls to this function to provide the default value of DM_REMOVE_NORMAL
for "normal" device removal.
This is in preparation for the driver specific pre-OS (e.g. DMA
cancelling) remove support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
The USB device should linked to VBUS regulator through "vbus-supply"
DTS property.
This patch adds handling for "vbus-supply" property inside the USB
device entry for turning on the VBUS regulator upon the host adapter probe.
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
At present devices use a simple integer offset to record the device tree
node associated with the device. In preparation for supporting a live
device tree, which uses a node pointer instead, refactor existing code to
access this field through an inline function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Drop board_ehci_power when dm usb used and switch to use
regulator api to handle vbus.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Implement ofdata_to_platdata to set the type to host or device.
- Check "dr-mode" property.
- If there is no "dr-mode", check phy_ctrl for i.MX6
and phy_status for i.MX7
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
I am not longer using my old email address
"ajay.bhargav@einfochips.com". For U-Boot development email address is
now updated to contact@8051projects.net
Signed-off-by: Ajay Bhargav <contact@8051projects.net>
This patch adds DM support to the xHCI PCI driver. Enabling its use
e.g. in x86 platforms.
Status: On the congatec BayTrail SoM, xHCI still does not work
correctly with this patch. Some internal timeouts lead to resets (BUG).
Additional work is needed here. I'm posting this version as WIP so that
other developers interested in this support might use it as a start.
I might get back to it in a few weeks as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cover-Letter: Fixes several spelling errors for the words "resetting",
"extended", "occur", and "multiple".
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mostly by adding MACH_SUN50I to some existing #ifdefs enable support
for the the HCI0 USB host controller on the A64.
Fix up some minor 64-bit hiccups on the way.
Add the bare minimum DT bits to the A64 .dtsi and enable the controllers
and the PHY on the Pine64.
This is limited to the first USB controller at the moment, which is
connected to the lower USB socket on the Pine64 board.
[Andre: remove unneeded defines, enable OHCI, add commit message]
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
OHCI has a known limitation of allowing only 32-bit DMA buffer
addresses, so we have a lot of u32 variables around, which are assigned
to pointers and vice versa. This obviously creates issues with 64-bit
systems, so the compiler complains here and there.
To allow compilation for 64-bit boards which use only memory below 4GB
anyway (and to avoid more invasive fixes), adjust some casts and types
and assume that the EDs and TDs are all located in the lower 4GB.
This fixes compilation of the OHCI driver for the Pine64.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Due to the peripheral clock driver improvement, remove the
unnecessary clock calling.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
This driver was recently converted to Driver Model, so missed the
subsystem-wide cleanups by commit 4052734273 ("usb: replace
ehci_*_remove() with usb_deregister()").
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
These two files have patch merge markers in them, within comments or
strings. Remove then, so that a search for merge markers does not show up
matches in these files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Currently the controller by default enables the Receive Detect feature in P3
mode in USB 3.0 PHY. However, USB 3.0 PHY does not reliably support receive
detection in P3 mode.
Enabling the USB3 controller to configure USB in P2 mode whenever the Receive
Detect feature is required.
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
This is required for better performance, and performs below tuning:
1. Enable burst length set, and define it as 4/8/16.
2. Set burst request limit to 16 requests.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Signed-off-by: Sriram Dash <sriram.dash@nxp.com>
USB ULPI PHY reset signals are typically active low. Consequently, they
should be marked as GPIO_ACTIVE_LOW in device tree, and indeed they are in
the Linux kernel DTs, and in DT properties that U-Boot doesn't yet use.
However, in DT properties that U-Boot does use, the value has been set to
0 (== GPIO_ACTIVE_HIGH) to work around a bug in U-Boot.
This change fixes the DT to correctly represent the HW, and fixes the
Tegra USB driver to cope with the fact that dm_gpio_set_value() internally
handles any inversions implied by the DT value GPIO_ACTIVE_LOW.
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
To enable this driver on Armada 7K/8K this patch adds the compatibility
property to the list.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Neta Zur Hershkovits <neta@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Omri Itach <omrii@marvell.com>
Cc: Igal Liberman <igall@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
This patch adds DM based support for the Armada 3700 EHCI controller.
The address windows don't need to get configured in this case. The
difference here is detected via DT compatible property at runtime.
With this support and the DM xHCI driver, both XHCI and eHCI can be
used simultaniously on the MVEBU boards now.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This patch adds DM based support for the xHCI USB 3.0 controller
integrated in the Armada 3700 SoC. It may be extended to be used
by other MVEBU SoCs as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Nadav Haklai <nadavh@marvell.com>
Cc: Kostya Porotchkin <kostap@marvell.com>
Cc: Wilson Ding <dingwei@marvell.com>
Cc: Victor Gu <xigu@marvell.com>
Cc: Hua Jing <jinghua@marvell.com>
Cc: Terry Zhou <bjzhou@marvell.com>
Cc: Hanna Hawa <hannah@marvell.com>
Cc: Haim Boot <hayim@marvell.com>
Acked-by: Marek Vasut <marex@denx.de>
This driver is designed in a generic manner, so resets should be
handled generically as well.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now, include/linux/errno.h is a wrapper of <asm-generic/errno.h>.
Replace all include directives for <asm-generic/errno.h> with
<linux/errno.h>.
<asm-generic/...> is supposed to be included from <asm/...> when
arch-headers fall back into generic implementation. Generally, they
should not be directly included from .c files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Add drivers/usb/host/xhci-rockchip.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Now, arch/${ARCH}/include/asm/errno.h and include/linux/errno.h have
the same content. (both just wrap <asm-generic/errno.h>)
Replace all include directives for <asm/errno.h> with <linux/errno.h>.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[trini: Fixup include/clk.]
Signed-off-by: Tom Rini <trini@konsulko.com>
The remove callbacks of EHCI drivers are often just a wrapper of
ehci_deregister.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This patch add support for rockchip dwc3 controller, which corresponding
to the two type-C port on rk3399 evb.
Only support usb2.0 currently for we have not enable the usb3.0 phy
driver and PD(fusb302) driver.
Signed-off-by: MengDongyang <daniel.meng@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This driver has not been converted to Driver Model, and it is an
obstacle to migrate other block device drivers. Remove it for now.
The UniPhier SoCs already use a DM-based EHCI driver, so now
ARCH_UNIPHIER can select DM_USB.
These two changes must be done atomically because removing the
legacy driver causes a build error.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Add driver model support while retaining the existing legacy code.
This allows the driver to support boards that have converted to
driver model as well as those that have not.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Simon Glass <sjg@chromium.org>
Moves code from ehci_hcd_init to new function ehci_fsl_init
which can be re-used in CONFIG_DM_USB.
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
The meaning of CONFIG_USB in U-Boot is different from that in Linux.
As you see in drivers/usb/Kconfig of Linux, CONFIG_USB enables the
USB host controller support, while CONFIG_USB_SUPPORT is used to
enable the whole of the USB sub-system.
When I added CONFIG_USB into Kconfig by commit 6e7e9294d3 ("usb:
add basic USB configs in Kconfig"), I planned to follow the Linux's
convention, i.e. CONFIG_USB to enable/disable the USB host support.
Then, commit 68f7c5db2d ("usb: Generic USB Kconfig option, that
fits both host and gadget and comments") changed the logic of the
CONFIG_USB to point to the whole of the USB sub-system. As a result,
currently we do not have an option for USB host.
This commit adds CONFIG_USB_HOST, which will be useful to compile
in the USB host support code.
CONFIG_USB_HOST is not referenced at all, but strangely some boards
define it in board headers. I removed them because USB_HOST will be
selected in Kconfig going forward.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
