We have changed to use dwc3 generic driver for usb3.0 host, so the
legacy Rockchip's xHCI driver is not needed, and drop it.
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Print the error code if the regulator enable fails, otherwise the error
message is rather useless and confusing.
Signed-off-by: Marek Vasut <marex@denx.de>
The regulator-fixed would return -ENOSYS when enabled/disabled,
because this operation is not supported, but this is not an error
e.g. on systems where the VBUS cannot be controlled, so if this
is the error code reported by the regulator core, consider it a
success and continue.
Signed-off-by: Marek Vasut <marex@denx.de>
The phy_bulk pointer *usb_phys is used before allocated,
fix it by using a phy_bulk variable instead in
xhci_dwc3_platdata struct
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
The omap3.dtsi file shows the usbhshost node with two sub-nodes
for ohci and ehci. This patch file creates the usbhshost, and
pulls the portX-mode information. It then locates the EHCI
sub-node, and initializes the EHCI controller with the info
pulled from the usbhshost node.
There is still more to do since there isn't an actual link
between the 'phys' reference and the corresponding phy driver,
and there is no nop-xceiv driver yet.
In the meantime, the older style reference to
CONFIG_OMAP_EHCI_PHYx_RESET_GPIO is still needed to pull
the phy out of reset until the phy driver is completed and the
phandle reference is made.
Signed-off-by: Adam Ford <aford173@gmail.com>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Have this symbol follow the pattern of all other such symbols.
This patch also removes a TODO from the code.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Have this symbol follow the pattern of all other such symbols.
This patch removes a TODO from the code.
Signed-off-by: Trevor Woerner <twoerner@gmail.com>
Add fuse check for USB. If the fuse indicates the module
will not work in the SoC, let's fail the initialization.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support the on-chip xHCI controller on
MediaTek SoCs, currently control/bulk/interrupt transfers are
supported.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Get a group of phys by the phy bulk API
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Weijie Gao <weijie.gao@mediatek.com>
dwc3-sti-glue has been broken since MISC uclass has been
modified to scan DT sub-nodes after bind.
Fixing it by a using the no-op uclass.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Solve issue for the display of "usb start" command on stm32mp1
because one carriage return is missing in DWC2 probe.
Before the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: Bus usbh-ehci@5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg@49000000: USB DWC2
Bus usbh-ehci@5800d000: USB EHCI 1.00
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Assert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already
initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at
default value, the host driver start with a clean state
(Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver
force device mode (called by ums or dfu command, before to execute
the usb start command).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK
is not activated the clk function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use generic phy to initialize the PHY associated to the
DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY
is not activated, the generic PHY function are stubbed.
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use ofnode_ instead of fdt_ APIs so that the drivers can support live DT.
This patch updates usb_get_dr_mode() and usb_get_maximum_speed() to use
ofnode as parameter instead of fdt offset. And all the drivers who use
these APIs update to use live dt APIs at the same time.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use dev_read_addr_ptr() instead of devfdt_get_addr() so that we can support
live DT.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Rather than keeping the asynchronous schedule running always, keep it
running only across USB mass storage transfers for now, as it seems
that keeping it running all the time interferes with certain control
transfers during device enumeration.
Note that running the async schedule all the time should not be an
issue, especially on EHCI HCD, as that one implements most of the
transfers using async schedule.
Note that we have usb_disable_asynch(), which however is utterly broken.
The usb_disable_asynch() blocks the USB core from doing async transfers
by setting a global flag. The async schedule should however be disabled
per USB controller. Moreover, setting a global flag does not prevent the
controller from using the async schedule, which e.g. the EHCI HCD does.
This patch implements additional callback to the controller, which
permits it to lock the async schedule and keep it running across
multiple transfers. Once the schedule is unlocked, it must also be
disabled. This thus prevents the async schedule from running outside
of the USB mass storage transfers.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Tom Rini <trini@konsulko.com> [omap3_beagle, previously failing]
At present dm/device.h includes the linux-compatible features. This
requires including linux/compat.h which in turn includes a lot of headers.
One of these is malloc.h which we thus end up including in every file in
U-Boot. Apart from the inefficiency of this, it is problematic for sandbox
which needs to use the system malloc() in some files.
Move the compatibility features into a separate header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present devres.h is included in all files that include dm.h but few
make use of it. Also this pulls in linux/compat which adds several more
headers. Drop the automatic inclusion and require files to include devres
themselves. This provides a good indication of which files use devres.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The xHCI 1.1 version also need set Transfer Type field
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Profiling the EHCI driver shows a significant performance problem in
ehci_submit_async(). Specifically, this function keeps enabling and
disabling async schedule back and forth for every single transaction.
However, enabling/disabling the async schedule does not take effect
immediatelly, but instead may take up to 1 mS (8 uFrames) to complete.
This impacts USB storage significantly, esp. since the recent reduction
of maximum transfer size to support more USB storage devices. This in
turn results in sharp increase in the number of ehci_submit_async()
calls. Since one USB storage BBB transfer does three such calls and
the maximum transfer size is 120 kiB, the overhead is 6 mS per 120 kiB,
which is unacceptable.
However, this overhead can be removed simply by keeping the async
schedule running. Specifically, the first transfer starts the async
schedule and then each and every subsequent transfer only adds a new
QH into that schedule, waits until the QH is completed and does NOT
disable the async schedule. The async schedule is stopped only by
shutting down the controller, which must happen before moving out
of U-Boot, otherwise the controller will corrupt memory.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
The ULP has two USB controllers. These two controllers have similar NC
registers layout as i.MX7D. But OTG0 uses UTMI PHY simliar as i.MX6, not
the integrated PHY on i.MX7D. The OTG1 needs off-chip HSIC PHY or ULPI PHY
to work.
This patch only supports OTG0 with UTMI PHY.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
This fixes the issues with calculation of controller indexes in
ehci_usb_bind() for iMX7, as USB controllers on iMX7 SoCs aren't
placed next to each other, and their addresses incremented by 0x10000.
Example of USB nodes for iMX7S/D:
usbotg1: usb@30b10000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b10000 0x200>;
^^^^^^^^^^
....
usbotg2: usb@30b20000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b20000 0x200>;
^^^^^^^^^^
....
usbh: usb@30b30000 {
compatible = "fsl,imx7d-usb", "fsl,imx27-usb";
reg = <0x30b30000 0x200>;
^^^^^^^^^^
....
Which was leading to usb enumeration issues:
Colibri iMX7 # usb start
starting USB...
Bus usb@30b10000: USB EHCI 1.00
Bus usb@30b20000: probe failed, error -22
scanning bus usb@30b10000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found
Fixes: 501547cec1("usb: ehci-mx6: Fix bus enumeration for DM case")
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
The xhci.h header file is currently located under drivers/usb/xhci
Move it to the include/usb folder to make it available to drivers that
are not under drivers/usb/xhci
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Some clock driver do not have a clk_enable() call back, and we should not
treat this as fail in ehci probe like other modules, eg. clk_enabl_bulk()
do not return fail if ret value is '-ENOSYS'
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
An USB 1.1 keyboard connected to dwc2 through a high-speed hub does not
report status until it changes. With this patch you can enable keyboard
by pressing a key while USB devices are probed. Without a keypress no
state is reported and the probe times out. We don't want to wait for a
keypress or timeout while polling for keypresses so implement an int_msg
nonblock variant that exits early on error.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
This quirk is necessary for the Amlogic GXL SoCs otherwise the
Port 2 PHY doesn't get out of suspend and U-Boot resets the board after:
XHCI timeout on event type 33... cannot recover.
BUG: failure at drivers/usb/host/xhci-ring.c:474/xhci_wait_for_event()!
BUG!
This quirk is also handled in the dwc3 core code, but until the
xhci-dwc3 driver uses the dwc3 core, the quirk must be handled here
to fix USB support on the Amlogic libretech-cc and libretech-ac board
when a device is only plugged in the OTG port.
Cc: Yuri Frolov <crashing.kernel@gmail.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Fixes: dc9cdf859e ("usb: dwc3: Add DWC3 controller driver support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add DM regulator support for toggling VBUS, this is useful on boards
which control the VBUS e.g. through GPIO.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Fix remaining checkpatch complaints in the driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Add missing Kconfig entry for the R8A66597 driver.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Convert the R8A66597 USB driver to DM and add support for DT probing.
Drop support for legacy non-DM and non-DT probing, since there are no
platform using that.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Replace R8A66597_BASE0 with proper SYSCFG0 accesses, no functional
change.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
While the USB controller can work both in LE and BE modes, there is
no user for the BE mode, so drop it. If there ever is a user for it,
it can be easily re-added back.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Replace in{bwl}()/out{bwl}() IO accessors with read{bwl}()/write{bwl}(),
to make the driver compile both on SH and ARM.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
No other platforms use this r8a66597 controller but RZ/A1,
make RZ/A1 support the default and drop all the other SoC
support to remove ifdeffery.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Remove CONFIG_SUPERH_ON_CHIP_R8A66597 macro, which is unused.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
commit 57faca19a8 ("drivers: USB: OHCI: allow compilation for 64-bit targets")
broke ohci support for the mpc85xx based socrates board,
as it removed volatile keyword from ohci_readl/writel.
Fix this so usb works again on socrates board.
Signed-off-by: Heiko Schocher <hs@denx.de>
var ohci_pci_ids is only used if DM_USB is not enabled.
So define this varaible only if
!CONFIG_IS_ENABLED(DM_USB)
Signed-off-by: Heiko Schocher <hs@denx.de>
Remove RK3399 compatible strings as this driver is no longer
used on that SoC.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Configure USB2 PHY register based on "phy_type" property and
handle all the quirks that are relevant for Rockchip RK3399 SoCs.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add compatible string for RK3399 and enable it by default on
Rockchip platforms with USB3 support.
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The EHCI iMX6 driver is only partly converted to DT probing and
still uses a tremendous amount of hard-coded addresses. Worse,
the driver uses hard-coded SoC-model-specific base addresses, which
are derived from values protected by SoC-specific macros, hence the
driver is also compiled for a specific SoC model. Even worse, the
driver depends on specific sequential indexing of the controllers,
from which it derives offsets in the PHY and ANATOP register sets.
However, when the driver is probed from DT, the indexing is not
correct. In fact, each controller has index 0. This patch derives
the index for DT probing case from the controller base addresses,
which is not the way this should be done, however it is the least
intrusive approach, favorable this close to release.
The necessary steps to convert this driver fully to DT probing are
described inside the patch, however this should be done in the next
release and depends on iMX clock driver patches.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.com>
Cc: Lukasz Majewski <lukma@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Vagrant Cascadian <vagrant@debian.org>
adopt 32 bit addr in fsl_esdhc for CONFIG_PPC.
So adopt 32 bit address for CONFIG_PPC.
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Per feedback from Marek, he suggested better handling and
to enable DM_FLAG_OS_PREPARE, this patch re-orders some of
the error checking, and errors returns the error code right
away and also sets DM_FLAG_OS_PREPARE.
Signed-off-by: Adam Ford <aford173@gmail.com>
This patch reuses some former code for the hawkboard, combines it
with some some similar DM_USB compatible code for the OHCI driver,
and enables the use of the da850's OHCI controller with DM_USB
compatibility.
Signed-off-by: Adam Ford <aford173@gmail.com>
There is a delay function that was commented out. This patch
re-enables it, because it will be needed for da850 ohci support.
Signed-off-by: Adam Ford <aford173@gmail.com>
This commit converts i.MX5's EHCI USB host driver to driver model (DM_USB).
It is a straightforward conversion (to reuse as much code as possible),
based on ehci-mx6.c code.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Move CONFIG_USB_EHCI_VF to drivers/usb/host/Kconfig and update the one
and only user thereof being colibri_vf.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
There exists code in drivers/common/common.c to read the dr_mode
from the device tree. This patch converts this driver to use that
function to initialize the driver.
Signed-off-by: Adam Ford <aford173@gmail.com>
Drop the counter, it has no meaning other than being the order in which
the interface is found; the name assigned to the USB host controller
interface is a better indicator.
Example of the original output:
> USB0: USB EHCI 1.10
> scanning bus 0 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Patched output:
> Bus usb@ee080100: USB EHCI 1.10
> scanning bus usb@ee080100 for devices... 2 USB Device(s) found
> scanning usb for storage devices... 1 Storage Device(s) found
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Migrate USB_EHCI_TEGRA from headers to Kconfig
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Tom Warren <twarren@nvidia.com>
Cc: Stephen Warren <swarren@nvidia.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Peter.Chubb@data61.csiro.au
Cc: Lucas Stach <dev@lynxeye.de>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Allen Martin <amartin@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Do the regulator related work only if the build has the DM_REGULATOR.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Now Allwinner platform is all set to use Generic USB
controller drivers, so remove the legacy sunxi drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Onc of key blocker for using USB Generic host controller
drivers in Allwinner are CLK and RESET drivers, now these
available for USB usage.
So switch sunxi USB use EHCI and OHCI Generic controllers.
Enabling USB is wisely a board choise, So Enable USB_OHCI_HCD
where it already have USB_EHCI_HCD
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
After updating the value of dev_context_ptrs[0], we should flush this
from cache to memory. Otherwise the xhci controller won't use it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Marek Vasut <marex@denx.de>
The keystone platforms can use the generic DC3 driver. Removing the
keystone-spcecific xchi driver and add the configuration options to enable
the generic DWC3 driver on all K2 platforms.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Those operations can be used for peripheral operation as well as host
operation.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
# Conflicts:
# drivers/usb/dwc3/core.c
# drivers/usb/host/xhci-dwc3.c
This allows to disable the USB driver model in SPL because it checks
the CONFIG_SPL_DM_USB variable for SPL builds. Nothing changes for
regular non-SPL builds.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Common USB code is built whenever USB is enabled (in non-SPL builds).
The USB uclass is built whenever (SPL_)DM_USB is enabled. Both need to
be independent from CMD_USB.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
This allows building the SPL without driver model for USB. Since
CONFIG_SPL_DM_USB is enabled if and only if CONFIG_DM_USB was enabled
before, this patch does not change the build behaviour.
Signed-off-by: Sven Schwermer <sven@svenschwermer.de>
Workaround makes FS as default mode on all affected socs.
Add support to check erratum-A005275 validity for an soc. This info is
required to determine whether a given soc is affected by this erratum.
Add quirk for this erratum "has_fsl_erratum_a005275" . This quirk is used
to enable workaround for the errata
Force FS mode as default by:
- making EPS as FS
- setting PFSC bit to disable HS chirping
This workaround can be disabled by mentioning "no_erratum_a005275" in
hwconfig string
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: York Sun <york.sun@nxp.com>
MSM uses the chipidea controller IP, however it requires
to reinit the phy after controller reset. in EHCI mode there's a
dedicated callback for it.
In device mode however there's no such callback.
Add implementaion of ci_init_after_reset() to implement the above
requirement in case CI_UDC driver is used.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
platdata_auto_alloc_size was not initialized in structure.
Caused null pointer dereference when configuring device as
gadget.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Add vbus-supply regulator support.
On some board vbus is not controlled by the phy but by
an external regulator.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add code to reset all reset signals as in usb DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Add support for operating a PHY attached to ehci-pci. There are
systems where the EHCI controller is internally wired to a PCI
bus and has a PHY connected to it as well, ie. the R-Car Gen2.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
On the A64 the clock for the first USB controller is actually the parent
of the clock for the second controller, so turning them off in that order
makes the system hang.
Fix this by only turning off *both* clocks when the *last* OHCI controller
is brought down. This covers the case when only one controller is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional usb from u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
For ohci, the maximam supported endpoint number is 32(in and out), and
now we have used (usb_pipeendpoint(pipe) << 1) to index the specified
endpoint descritor, usb_pipeendpoint(pipe) can reach 0xf, so we need
change the NUM_EDs from 8 to 32.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
ohci-hcd casts priv_data pointer to (ohci_t *), thus it must be
the first member in private data struct.
Fixes 831cc98b1 ("usb: sunxi: Simplify ccm reg base code")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
struct sunxi_ccm_reg doesn't have ahb_reset0_cfg on sun4i and sun5i,
thus compilation fails with:
drivers/usb/host/ohci-sunxi.c:96:26: error: 'struct sunxi_ccm_reg' has
no member named 'ahb_reset0_cfg'
Access this reg using its offset to fix this issue.
Fixes commit 1ed9c1118 ("usb: sunxi: ehci: get rid of ifdefs")
and commit 56830cee3 ("usb: sunxi: ohci: get rid of ifdefs")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
On A64 OHCI1 clock source is OHCI0 clock, so we need to enable OHCI0
clock when OHCI1 is in use.
Fixes commit dd3228170a ("usb: sunxi: Switch to use generic-phy")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
