We already have the CONFIG_SYS_VENDOR variable, which defines the
manufacturer of the board. The value in CONFIG_G_DNL_MANUFACTURER
is just a duplicity, so switch it to reuse CONFIG_SYS_VENDOR .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
There is no VT for this board, so remove this incorrect macro.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
There is no VT for this board, so remove this incorrect macro.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
This patch adds the necessary OF alias for the UDC node, which let's
the code locate the DWC2 UDC base address in OF instead of hard-coding
it into the U-Boot binary. The code is adjusted to use the address from
OF instead of the hard-coded one. Finally, the hard-coded address is
removed and USB DM support is enabled.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Lukasz Majewski <l.majewski@majess.pl>
Cc: Lukasz Majewski <l.majewski@samsung.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
The Micrel PHY configuration is now done from OF, so hard-coding
the configuration into the board file is no longer necessary.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Enable command auto completion and enable $version variable. This makes
working with U-Boot far more enjoyable.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Preset the $loadaddr environment variable to some sane default, let's
say half of the RAM. This variable is where the kernel is loaded using
all sorts of .*load commands, so it's convenient to have it set.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The monitor is growing much larger with various additions, like fitImage,
command line completion, UBI etc. Make the monitor area larger so these
features can be safely added.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reorder the 10m50 and 3c120 config files such, that the environment
position can be calculated from the monitor size. The environment is
placed right after the monitor. This removes one more ad-hoc variable.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
LL_TEMAC is available at big endian MB and it is not properly tested
that's why the patch removes it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Create space below u-boot binary for early malloc.
It means memory layout is stack grows down, space for early malloc,
u-boot code.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Update the ZYBO device tree and enable config options that relate to the
added devices in the device tree.
Signed-off-by: Nathan Rossi <nathan@nathanrossi.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The s3c-otg IP block is in fact a DWC2 OTG one, so finally rename the
config option to make it less misleading. No functional change, just
a mechanical change done using the following script:
git grep USB_GADGET_S3C_UDC_OTG | cut -d : -f 1 | sort -u | \
while read line ; do
sed -i "s/USB_GADGET_S3C_UDC_OTG/USB_GADGET_DWC2_OTG/g" $line ;
done
Signed-off-by: Marek Vasut <marex@denx.de>
Freescale ARM-based Layerscape contains a SATA controller
which comply with the serial ATA 3.0 specification and the
AHCI 1.3 specification.
This patch adds SATA feature on ls2080aqds, ls2080ardb and
ls1043aqds boards.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Secure Boot Target from NOR has been added.
- Configs defined to enable esbc_validate.
- ESBC Address in header is made 64 bit.
- SMMU is re-configured in Bypass mode.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MC and debug server are not board-specific. Move reserving memory to SoC
file, using the new board_reserve_ram_top function. Reduce debug server
memory by 2MB to make room for secure memory.
In the system with MC and debug server, the top of u-boot memory
is not the end of memory. PRAM is not used for this reservation.
Signed-off-by: York Sun <yorksun@freescale.com>
Switch Novena to distro bootcmd, so it can be used with debian easily.
Signed-off-by: Vagrant Cascadian <vagrant@aikidev.net>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Vagrant Cascadian <vagrant@aikidev.net>
kylin board use rk3036 SOC, 512M sdram, 8G emmc.
This add some basic files required to allow the board
to output serial message and can run command(mmc info etc).
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove 115200 from "earlycon" to avoid loss of initial
log messages during linux kernel 4.1 bootup
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch also expose the complete DDR region(s) to Linux.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Support qspi flashes for mx7dsabresd
1. introduce pin mux settings
2. enable qspi clock
3. introduce related macro definitions
Default QSPI is not enabled, since we need hardware rework to use QSPI,
see SPF-28590, page 9:
"
QSPI signals are muxed with EPDC_D[7:0]
When using QSPI: de-populate R388-R391, R396-R399
populate R392-R395, R299, R300
"
After hardware rework, define CONFIG_FSL_QSPI in mx7dsabresd.h. qspi
flashes can be deteced and read/erase/write. Log info:
"
=> sf probe
SF: Detected MX25L51235F with page size 256 Bytes, erase size 64 KiB, total 64 MiB
=> sf read 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Read: OK
=> sf erase 0 0x4000000
SF: 67108864 bytes @ 0x0 Erased: OK
=> sf write 0x80000000 0 0x4000000
device 0 whole chip
SF: 67108864 bytes @ 0x0 Written: OK
"
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Enabled support for AXP818 in SPL and u-boot.
DCDC1, DCDC2, DCDC3 and DCSC5 are enabled.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Allwinner A83T is octa-core cortex-a7 SOC.
This enables support for A83T.
SMP is not yet supported.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
There are some options which are never used, and also some options
which are selected by others but have never been a Kconfg option.
Clean these up.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
This commit "677f970bc62a661690b3431543d5a5d5e682ba70" introduce a new
macro "CONFIG_FSL_CLK" that get_clocks() should not be limited by ESDHC.
But that patch missed to enable it for i.MX7. THis patch enables
CONFIG_FSL_CLK to let get_clocks work.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
The patch
"board_init: Change the logic to setup malloc_base"
(sha1: 9ac4fc8207)
breaks SPL for Zynq because it puts early alloc area on the stack which
caused that stack was decreased by CONFIG_SYS_MALLOC_F_LEN (0x400)
and there was not enough space for regular stack.
This patch changes memory layout to better utilize the last 64k OCM
block.
0xffff0000 - 0xfff1000 - Full malloc space
0xffff1000 - 0xffff300 - Stack location
0xfffff300 - CONFIG_SYS_MALLOC_F_LEN - Early malloc space
0xfffffd00 - sizeof(GD) - GD
0xfffffe00 - 0xffffffff - SoC specific boot code
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Moritz Fischer <moritz.fischer@ettus.com>
- Enable DM_ETH by default for Zynq and ZynqMP
- Remove board_eth_init code
- Change miiphy_read function to return value instead of error code
based on DM requirement
- Do not enable EMIO DT support by default
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
CONFIG_API is causing compilation error when DM_ETH is enabled because
eth_get_dev() is not available.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The SR1500 board is a CycloneV based board, similar to the EBV
SoCrates, equipped with the following devices:
- SPI NOR
- eMMC
- Ethernet
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
This symbol is no longer used anywhere, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Heiko Schocher <hs@denx.de>
Reworked the LEON2 start.S code to call board_init_f function at startup.
Also implemented the relocate_code function in assembly to relocate the
monitor and setup the stack pointer before calling relocated board_init_r.
Add the CONFIG_SYS_GENERIC_BOARD variable to all the LEON2 boards.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Reworked the LEON3 start.S code to call board_init_f function at startup.
Also implemented the relocate_code function in assembly to relocate the
monitor and setup the stack pointer before calling relocated board_init_r.
Add the CONFIG_SYS_GENERIC_BOARD variable to all the LEON3 boards.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Simple patch to enable support for extfs filesystem in SPL,
this is useful to those who want to avoid vfat like plague.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Commit 1eb0c03c21 added
SPL_SYS_MALLOC_SIMPLE Kconfig option and changed the way it is
evaluated.
Thus, the definitions of CONFIG_SYS_MALLOC_SIMPLE in rk3***_common.h
board configs are now incorrect because CONFIG_SPL_BUILD is enabled so
CONFIG_IS_ENABLED(SYS_MALLOC_SIMPLE) will look for SPL_SYS_MALLOC_SIMPLE
instead of SYS_MALLOC_SIMPLE.
This commit fix this enabling SPL_SYS_MALLOC_SIMPLE with the new Kconfig
option by default in rockchip-mach.
Signed-off-by: Ariel D'Alessandro <ariel@vanguardiasur.com.ar>
Acked-by: Simon Glass <sjg@chromium.org>
This add some basic files required to allow the board to dispaly
serial message and can run command(mmc info etc)
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Moved board Kconfig fragment from previous patch into this one to fix
build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-changes: 8
- moved board Kconfig fragment from previous patch into this one
rk3036 only 4K size SRAM for SPL, so only support
timer, uart, sdram driver in SPL stage, when finish
initial sdram, back to bootrom.And in rk3036 sdmmc and
debug uart use same iomux, so if you want to boot from
sdmmc, you must disable debug uart.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Fixed build error for chromebook_jerry, firefly-rk3288:
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-changes: 8
- Fix build error for chromebook_jerry, firefly-rk3288
some rockchips soc will not use uclass in SPL stage,
so define config to decide whether to build common.c
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
some rockchip soc will not include lib/timer.c in SPL stage,
so implement timer driver for some soc can use us delay function in SPL.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Save the environment on the SD card for Firefly in the empty space
between the SPL and the u-boot image.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Similar to load an fdt, when loading an initrd about the 512Mb mark
things seem to break. For now force loading below 512Mb until the reason
why this fails has been determined/solved.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
This is not supported with driver model, so print a message instead of
generating a build error. Rescanning PCI is not yet implemented.
This function will be implemented later once some additional PCI driver
model improvements are merged. It was confirmed on the mailing list
that no one on the tegra side will miss this feature, so it is disabled
for tegra.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
To group all dm timer drivers together, move tsc timer to
drivers/timer directory.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The board supports following features:
- Boot media support: SD card/e.MMC/SPI flash,
- Support LCD display (optional, disabled by default),
- Support ethernet,
- Support USB mass storage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
[fix checkpatch warnings]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As the environment variables "serial#" and "ethaddr" need to be
overwriten by the users, CONFIG_ENV_OVERWRITE is defined to disable
the write protection. Anybody can change or delete these parameters.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel
fails to access the device tree blob on boot. The reason is that u-boot
relocates the device tree blob into high memory when booting the kernel
and the kernel is unable to access the blob.
To avoid this issue, fdt_high is set to the value of 0xffffffff. The
device tree blob will not get relocated and is still in low memory to
make it accessible to the kernel.
For the same reason, initrd_high is set to the value of 0xffffffff too.
This patch is to update fdt_high and initrd_high for LS1021AQDS board.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for the third USB controller for LS1043A.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Use the U-Boot Driver Model. Just enable Freescale DSPI driver
and set DSPI related parameters in dts file.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043AQDS Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 DIMM
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* Two RGMII ports
* XFI 10G port
* SGMII
* QSGMII with 4x 1G ports
PCIe: supports Gen 1 and Gen 2
SATA 3.0: one SATA 3.0 port
USB 3.0: two micro AB connector and one type A connector
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
[York Sun: Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale's LS2085A is a another personality of LS2080A SoC with
support of AIOP and DP-DDR.
This Patch adds support of LS2085A Personality.
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Updated MAINTAINERS files
Dropped #ifdef in cpu.h
Add CONFIG_SYS_NS16550=y in defconfig]
Reviewed-by: York Sun <yorksun@freescale.com>
LS2080A is a prime personality of Freescale’s LS2085A. It is a non-AIOP
personality without support of DP-DDR, L2 switch, 1588, PCIe endpoint etc.
So renaming existing LS2085A code base to reflect LS2080A (Prime personality)
Signed-off-by: Pratiyush Mohan Srivastava <pratiyush.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
[York Sun: Dropped #ifdef in cpu.c for cpu_type_list]
Reviewed-by: York Sun <yorksun@freescale.com>
Management complex Firmware, DPL and DPC are depolyed during u-boot boot
sequence.
Add new DPAA2 commands to manage Management Complex (MC) i.e. start mc, aiop
and apply DPL from u-boot command prompt.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove fsloadcmd / ext2load as we are using load command
which use the corresponding latest file system command.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
socfpga_dw_mmc driver will obtain the drvsel and
smplsel value from device tree instead of definition
in config header file.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
This board was constantly parasiting on the CV SoCDK, so split it
into it's own separate directory. Moreover, the board config was
missing important bits, like simple-bus support in SPL, the DRAM
configuration was incorrect and the DTS was also missing the pre
reloc bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: Jan Viktorin <viktorin@rehivetech.com>
When adding support for the Arria10 platform, we're going to name the file
base_addr_a10.h, so to be systematic about it, rename the socfpga_base_addr.h
to be base_addr_ac5.h for the Arria5 and Cyclone5 platform.
Suggested-by: Marek Vasut <marex@denx.de>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
This patch add ZyXEL NSA310S 1-Bay Media Server
The ZyXEL NSA310S device is a Kirkwood based NAS:
- SoC: Marvell 88F6702 1000Mhz
- SDRAM memory: 256MB DDR2 400Mhz
- Gigabit ethernet: PHY Marvell 88E1318
- Flash memory: 128MB
- 1 Power button
- 1 Power LED (blue)
- 4 Status LED (green)
- 1 Copy/Sync button
- 1 Reset button
- 1 SATA II port
- 2 USB 2.0 ports (front and back)
- Smart fan
Signed-off-by: Gerald Kerma <dreagle@doukki.net>
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
There are already Kconfig options for SPI flash drivers, but we
have not moved them from config.h to defconfig files. This commit
does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
There are already Kconfig options for SPI drivers, but we
have not moved them from config.h to defconfig files. This
commit does this in a batch.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Congatec has several MX6 boards based on quad, dual, dual-lite and solo.
Add SPL support so that all the variants can be supported
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Congatec boards boot from SPI NOR, so it makes more sense to use
SPI NOR to store the environment variables.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Using 50 MiB malloc pool in SPL is nonsense. Since the caches are not
enabled in SPL, it takes 2 seconds to init the pool and has no obvious
benefit. Reduce the size to 1 MiB.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Tested-by: Stefano Babic <sbabic@denx.de>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Add initial sun8i H3 support, only uart + mmc are supported for now.
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
The DFU protocol implementation in U-Boot is much faster than the
FEL protocol implementation in the boot ROM on Allwinner devices.
Using DFU instead of FEL improves the USB transfer speed from
500-900 KB/s to 3.2-3.7 MB/s. This is particularly useful for
reducing the time needed for booting systems with large initrd
images.
FEL is still useful for loading the U-Boot bootloader and a boot
script, which may then activate DFU in the following way:
setenv dfu_alt_info ${dfu_alt_info_ram}
dfu 0 ram 0
bootm ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr_r}
The rest of the files can be transferred to the device using the
"dfu-util" tool.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Add support for storing the environment in CFI NOR flash on Juno and FVP
models.
I also removed some config values that are not used by CFI flash parts.
Juno has 1 flash part with 259 sectors. The first 255 sectors are
0x40000 (256kb) and are followed by 4 sectors of 0x10000 (64KB).
FVP models simulate a 64MB NOR flash part at base address 0x0FFC0000.
This part has 256 x 256kb sectors. We use the last sector to store the
environment.
To save the NOR flash to a file, the following parameters should be
passed to the model:
-C bp.flashloader1.fname=${FILENAME}
-C bp.flashloader1.fnameWrite=${FILENAME}
Foundation models don't simulate the NOR flash, but having NOR support
in the u-boot binary does not harm: attempting to write to the NOR will
fail gracefully.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch allows vexpress64 targets to be compiled when
CONFIG_SYS_FLASH_CFI is enabled.
I considered using #warning instead of #error, but this just clutters up
the build output and hides real warnings.
Without this patch, you see errors during compilation like this:
include/configs/vexpress_aemv8a.h:42:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
include/configs/vexpress_aemv8a.h:115:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
include/configs/vexpress_aemv8a.h:280:2: error: #error "Unknown board
variant"
#error "Unknown board variant"
make[1]: *** [tools/envcrc.o] Error 1
make: *** [tools] Error 2
In file included from include/config.h:5:0,
from tools/envcrc.c:19:
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch makes the 2nd DRAM bank available on Juno only and not on
other vexpress64 targets, eg. the FVP models.
The commit below added a 2nd bank of NOR flash for Juno, but also for
all vexpress64 targets:
commit 2d0cee1ca2
Author: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Date: Mon Oct 19 11:08:31 2015 +0100
vexpress64: Juno: Declare all 8GB of RAM and make them visible to the kernel.
Juno comes with 8GB RAM, but U-Boot only passes 2GB to the kernel.
Declare a secondary memory bank and set the sizes correctly.
Signed-off-by: Liviu Dudau <Liviu.Dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Ryan Harkin <ryan.harkin@linaro.org>
Tested-by: Ryan Harkin <ryan.harkin@linaro.org>
Unfortunately, I only fully tested on Juno R0, R1 and the FVP Foundation
model. Whilst FVP Base AEMV8 models run U-Boot OK, they fail to boot
the kernel.
Signed-off-by: Ryan Harkin <ryan.harkin@linaro.org>
Acked-by: Liviu Dudau <liviu.dudau@foss.arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
This option only complicates the code unnecessarily, just use
CONFIG_SYS_DEF_EEPROM_ADDR as the default address if there are
only five arguments to eeprom {read/write} if this is defined.
If CONFIG_SYS_DEF_EEPROM_ADDR is not defined, we mandate all
six arguments.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Cc: Heiko Schocher <hs@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
The NOR flash on Keystone 2 evms has a u-boot-spl partition size of
0x80000.
Currently burn_uboot_spi will erase 0x100000 from the spi NOR which will
cause a partial erase of the misc partition.
Fix this by correcting the erase size.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Change to ns16550 uart for 10m50 devboard based on a new
Altera release.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Zap CONFIG_NS16550_SERIAL, as the unification of ns16550 drivers
is completed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_omap, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_tegra, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_dw, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Unify serial_keystone, and use the generic binding.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Simon Glass <sjg@chromium.org>
Allow console recording so that tests can use it. Also allow the console
output to be suppressed, to reduce test output 'noise'.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some boards have an i8042 device. Enable the driver for all x86 boards, and
add a device tree node for those which may have this keyboard.
Also adjust the configuration so that i8042 is always separate from the VGA,
and rename the stdin driver accordingly. With this commit the keyboard will
not work, but it is fixed in the next commit.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a sandbox timer which get time from host os and a basic
test.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Simon Glass <sjg@chromium.org>
CONFIG_CONSOLE_CURSOR, CONFIG_SYS_CONSOLE_BLINK_COUNT and
CONFIG_CONSOLE_TIME are not used by any board. The implementation is not
great and stands in the way of a refactor of i8042. Drop these for now.
They can be re-introduced quite easily later, perhaps with driver-model
real-time-clock (RTC) support.
When reintroducing, it might be useful to make a few changes:
- Blink time would be more useful than blink count
- The confusing #ifdefs should be avoided
- The time functions should support driver model
- It would be best keyed off console_tstc() or some similar idle loop
rather than a particular input driver (i8042 in this case)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
zc1571 with silicon can operate on 200MHz maximum frequency. Setup this
frequency by default and fix setting for ep108.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
OF_CONTROL is enabled by default for all Zynq boards.
The difference between two boot images is done by OF_SEPARATE
or OF_EMBED macros.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This board uses the same CPU (8309) as VECT1. The memory however is
different since it has NAND Flash, the NOR Flash partitioning is
different and of course the FPGAs as well.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
It should be after the u-boot reserved sectors and before the env
sectors, since the solution used for kmvect1 (tell the linker to put the
firmware into the u-boot produced binary, at the end of the area) should
be the exception.
The #define is only "conditional" so that we can still support kmvect1.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The hardcoded value are bad, since the address could change between
different boards.
Furthermore, the relevant #defines are set only if #undefined here, so
that they can be changed by some boards if required.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
The ODT parameters for km8360 set the ODT_WR_ACS bit in u-boot KM-2011.09
that is used in the release bootpackage for kmcoge5ne. During the
transition from the kmeter1 to km8360 this was changed to
ODT_RD_ONLY_CURRENT, which is uncorrect and causes faulty RAM accesses at
low temperatures.
This is now changed to ODT_WR_ONLY_CURRENT which is the equivalent of
ODT_WR_ACS.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
For consistency with all the other km83xx plaforms, this should also be
defined for km8309. The same settings as for km8321 are taken.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
On the km8321 boards is CONFIG_SYS_DDRCDR not defined, which leads to
the DDRCDR not being configured at startup and still containing the
reset value.
The required settings for our km8321 hardware designs are different than
the reset value and must be set with CONFIG_SYS_DDRCDR, that is used
by mpc83xx's cpu_init_f function at early CPU initialization.
The important settings are the DDR2 internal voltage level and the
half-strength "drivers".
In our case where the DRAM chips are soldered on board and the routing
for these signals under control, half-strength is sufficient as a few
measurements done in the lasts have shown. Since all the hardware
qualification tests have been performed with half strength, the nominal
strength settings are removed in favor of the default reset half
strength settings.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
We use the same settings for open firmware defines on all our powerpc
targets, so move them from the CPU specific headers to the common
powerpc header.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
128kByte and 3,986MB may be in the future too little for kernel the fdt
blob respectively the kernel image. So increase the reserved areas here,
we have the space for this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This board is similar to TUXX1, but it has differend FPGAs.
Signed-off-by: Christoph Dietrich <christoph.dietrich@keymile.com>
Signed-off-by: Andreas Huber <andreas.huber@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
If a DTB is found with cramfsls, the bootscript continues as expected.
If none is found, the cramfsloadfdt and boot subbootcmds are updated to
not load the DTB from cramfs and not pass it to the kernel. The kernel
thus must have an appended DTB otherwise the boot will fail.
This is required for the km_kirkwood boards that must support .esw where
the DTB sometimes is appended (for backwards compatibility) and sometimes
is passed correctly (as we do now for all newer boards).
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
To prevent u-boot to stop accidently e.g. due to line noise on the
serial line, we now use the option CONFIG_AUTOBOOT_KEYED. We choose the
<SPACE> key for this.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
KM_ENV_BUS was used for nothing else than an direct assignment to
CONFIG_I2C_ENV_EEPROM_BUS. To avoid this, directly use
CONFIG_I2C_ENV_EEPROM_BUS instead.
Patchwork: http://patchwork.ozlabs.org/patch/399411/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
SeeedStudio BeagleBone Green (BBG) is clone of the BeagleBone Black (BBB) minus
the HDMI port and addition of two Grove connectors (i2c2 and usart2).
This board can be identified by the 1A value after A335BNLT (BBB) in the at24 eeprom:
1A: [aa 55 33 ee 41 33 33 35 42 4e 4c 54 1a 00 00 00 |.U3.A335BNLT....|]
http://beagleboard.org/greenhttp://www.seeedstudio.com/wiki/Beaglebone_green
In Mainline Kernel as of:
https://git.kernel.org/cgit/linux/kernel/git/torvalds/linux.git/commit/?id=79a4e64c679d8a0b1037da174e4aea578c80c4e6
Patch tested on BeagleBone Black (rev C) and BeagleBone Green (production model)
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Jason Kridner <jkridner@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Use spl alternate boot device feature to define fallback to
the main boot device as it is defined by hardware.
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
BeagleBoard X15 (http://beagleboard.org/x15) support in u-boot does
actually support two different platform configuration offered by
TI. In addition to BeagleBoard X15, it also supports the TMDXEVM5728
(or more commonly known as AM5728-evm).
Information about the TI AM57xx EVM can be found here
http://www.ti.com/tool/tmdxevm5728
The EVM configuration is 1-1 compatible with BeagleBoard X15 with the
additional support for mPCIe, mSATA, LCD, touchscreen, Camera, push
button and TI's wlink8 offering.
Hence, we rename the beagle_x15 directory to am57xx to support TI
EVMs that use the AM57xx processor. By doing this we have common code
reuse. This sets the stage to have a common u-boot image solution for
multiple TI EVMs such as that already done for am335x and am437x. This
sets the stage for upcoming multiple TI EVMs that share the same code
base.
NOTE: Commit eae7ae1853 ("am437x: Add am57xx_evm_defconfig using
CONFIG_DM") introduced DT support for beagle_x15 under am57xx_evm
platform name. However, this ignored the potential confusion arising for
users as a result. To prevent this, existing beagle_x15_defconfig is
renamed as am57xx_evm_nodt_defconfig to denote that this is the "non
device tree" configuration for the same platform. We still retain
am57xx-beagle-x15.dts at this point, since we just require the common
minimum dts.
As a result of this change, users should expect changes in build
procedures('make am57xx_evm_nodt_defconfig' instead of 'make
beagle_x15_defconfig'). Hopefully, this would be a one-time change.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Schuyler Patton <spatton@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Lokesh Vutla <lokeshvutla@ti.com>
Mainline kernel for this device has only support for device tree. We can safely
drop this legacy code.
Signed-off-by: Luka Perkov <luka.perkov@sartura.hr>
Create include/configs/mv-plug-common.h for common definitions
for Sheevaplug, Guruplug and Dreamplug. This will make it easier
to ensure the built u-boots stay in track with each other
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Cosmetic: CONFIG_OF_LIBFDT was in a different position in the config
file for the Dreamplug, compared to the Sheevaplug and Guruplug.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
include/configs/mv-common.h brings in the required filesystems if
CONFIG_SYS_MVFS is defined, so use it for Sheevaplug and Guruplug.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
For Marvell plugs, move the configuration of DHCP, NAND/SF, PING
and USB commands, and HUSH_PARSER into the _defconfig file, rather
than the include/configs/*plug.h files.
This avoids compiler warnings of duplicate definitions if the
option is selected in the .config, but also defined in the
include/configs/*plug.h file.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
The Marvell plugs are very similar systems, and so it makes sense
for their u-boots to have the same commands/configuration.
Add EXT4 and MII to Dreamplug, DATE to Guruplug and Sheevaplug.
Add CONFIG_SYS_ALT_MEMTEST to Sheevaplug.
There are still command differences around NAND, SPI/NOR.
Also default to building u-boot.kwb for Sheevaplug and Guruplug.
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
With this change Synopsys DesignWare SDP board is switched to driver
model for both serial port (serial_dw) and Ethernet (Designware GMAC).
This simplifies include/configs/axs101.h and allows for reuse of Linux's
Device Tree description.
For simplicity Linux's .dts files are not blindly copied but only very
few extracts of them are really used (those that are supported in U-Boot
at the moment).
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Enable TI_EDMA3 and QUAD read support for ti_qspi on am43xx, this
increases read performance to 4 MB/s.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
CONFIG_SYS_EARLY_PCI_INIT is not needed any more since with driver
model, PCI enumeration is automatically triggered.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move chipset-specific codes such as PAM init, PCIe ECAM and MP table
from pci.c to qemu.c, to prepare for DM PCI conversion.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Rename pcat_timer.c to i8254.c and pcat_interrupts.c to i8259.c,
to match their header file names (i8254.h and i8259.h).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
CONFIG_SYS_NUM_IRQS is actually not something we can configure,
but an architecture defined number of ISA IRQs. Move it from
x86-common.h to asm/interrupt.h and rename it to SYS_NUM_IRQS.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
wandboard and mx6cuboxi have warnings because BOOT_DELAY
is defined twice.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Vagrant Cascadian <vagrant@debian.org>
CC: Otavio Salvador <otavio@ossystems.com.br>
CC: Fabio Estevam <fabio.estevam@freescale.com>
Add an initr function in the board_r.c file for the AMBA Plug&Play
command. Add a Kconfig entry for the ambapp command and remove all
CONFIG_CMD_AMBAPP defines from the board configuration headers.
Add a Kconfig entry to display the AMBA Plug&Play information
on startup. This option is off by default. Remove relevent define
from board configuration headers.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Update the GRSIM board with the memory settings for the evaluation
version of TSIM. This free version of TSIM is used for testing.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
Update the LEON2/3 serial driver to make use of the readl and writel
macros as well as the WATCHDOG_RESET() macro.
Add readl/writel and friends to the asm/io.h file.
Introduce the gd->arch.uart variable to store register address.
Lastly, remove baudrate scaler macro variables from board config. It
is now calculated in the serial driver using the global data variable.
Signed-off-by: Francois Retief <fgretief@spaceteq.co.za>
This adds support to update firmware on qspi flash present on
am437x-sk-evm and am43xx-epos-evm via DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D u-boot.bin -a u-boot.bin
Signed-off-by: Vignesh R <vigneshr@ti.com>
-> Add National instrument ethernet transceiver configuration used (DP83848)
-> Change cpsw slave phy address
-> modify nand configuration to use the correct ECC and correct nand features
CONFIG_BOOTDELAY is defined in config_distro_defaults.h
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
[trini: Drop omap3_logic.h settings which were a warning and no longer
correct usage].
Signed-off-by: Tom Rini <trini@konsulko.com>
The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Since we don't have for sure a valid IP-setup during
board_late_init(...) because it maybe allready stored in environment or
not, we cannot form a proper vxWorks bootline at this place.
So we move to the way, forming the bootline just before
executing/launching vxWorks. To do this we use the bootvx command
instead go.
We only have to form the "othbootargs" environment variable, the rest is
done pretty good by the "bootvx" commannd.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Support LCDIF for mx7dsabresd board:
1. Add pinmux settings
2. Add VIDEO related macro definition and videomode env settings.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Adrian Alonso <aalonso@freescale.com>
Support lcdif display:
1. Add pinmux and pad settings for LCDIF
2. Introduce setup_lcd to do the settings for LCDIF
3. Enable VIDEO related macros in board header files
4. Add a new env videomode which is needed by mxsfb.c. The
settings for videomode in this patch is for TFT43AB.
5. Tested on mx6ul 14x14/9x9 evk.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
The kernel_addr_r should be set to the same value as CONFIG_LOADADDR,
get rid of the duplication.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Stefano Babic <sbabic@denx.de>
Support PSCI and switch to non-secure mode when booting linux.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This allows for more flexible and standardized boot across multiple
platforms.
Remove redundant legacy boot environment.
Cc: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
This allows for more flexible and standardized boot across multiple
platforms.
Remove redundant legacy boot environment.
Signed-off-by: Vagrant Cascadian <vagrant@debian.org>
Enable the GPU node in the system-wide ft_system_setup() hook instead of
the board-specific ft_board_hook(). This allows us to enable GPU per SoC
generation instead of per-board as we did initially.
Reported-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
p2371-2180 has two PCI ports; a regular x4 slot and a x1 M.2 slot. This
patch adds the relevant DT to enable the PCI controller and configure
the XUSB padctl pin muxing, and code to turn on the PCI power and enable
PCI features in U-Boot. I have only tested the x4 slot.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Rename board nios2-generic to 3c120_devboard. Since nios2 is
converted to driver model and device tree control of u-boot,
the nios2-generic board directory is removed. We can rename
the board back to a real board name. Now the boards maintained
in u-boot mainline are the same as Linux kernel, namely 3c120
and 10m50.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Do not allocate rx buf in net.c, because altera_tse allocates
its own rx buf in driver. This can save 6KB memory.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Now that we have solved the problems that prevented this feature from
being enabled, enable it everywhere.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
The tricorder and tricorder_flash boards have grown too big.
Reduce their size by building them with CONFIG_SYS_THUMB_BUILD.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This target is ARMv7-M therefore can only build for Thumb,
but it did not #define CONFIG_SYS_THUMB_BUILD, so the U-Boot
code did not know it had to build for Thumb(2), not ARM.
This patch is binary-invariant: builds of stm32f429-discovery
with and without this patch were compared and found to differ
only by their U-Boot version strings.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Trim CONFIG_SYS_MEMTEST_END location.
CONFIG_SYS_MONITOR_LEN
Reserving 256k for U-Boot at: d7fc0000
CONFIG_ENV_SIZE
CONFIG_SYS_MALLOC_LEN
Reserving 256k for malloc() at: d7f80000
0x10000 for the rest
Reserving 68 Bytes for Board Info at: d7f7ffbc
Reserving 208 Bytes for Global Data at: d7f7feec
Reserving 12000 Bytes for FDT at: d7f7d00c
Stack
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Trim CONFIG_SYS_MALLOC_LEN size, because CONFIG_ENV_SIZE
is included to total memory allocation in common.h,
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Chin Liang See <clsee@altera.com>
Remove CONFIG_SYS_INIT_SP macro, as the initial stack is set to
below the u-boot code.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
Remove CONFIG_SYS_MALLOC_BASE macro, as it is not used by
the generic board.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Chin Liang See <clsee@altera.com>
Clean up macros that do not need a value as suggested by
Marek.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Use dram bank in board info, so that it displays correct
memory values in bdinfo command.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
This board runs a P5020 or P5040 chip, and utilizes
an EEPROM with similar formatting to the Freescale P5020DS.
Large amounts of this code were developed by
Adrian Cox <adrian at humboldt dot co dot uk>
Signed-off-by: Andy Fleming <afleming@gmail.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Update this driver to use driver model and change all users.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Production boards should not use CONFIG_OF_EMBED. Fix this for the Zybo
boards.
The image to use now becomes u-boot-dtb.bin.
For example, the .bif file should contain a line like:
[load = 0x04000000,startup=0x04000000]/path/to/u-boot-dtb.bin
instead of:
[load = 0x04000000,startup=0x04000000]/path/to/u-boot.bin
When device tree is enabled we need to load u-boot-dtb.img. Change the
settings so that SPL does the right thing.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable CONFIG_SYS_I2C_ZYNQ only if it has either I2C0 or I2C1
enabled in a board config.This fixes the issue of i2c error
during board init if board specific doesnt have either I2C0
or I2C1.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds support to update firmware on qspi flash using DFU.
On device:
=> setenv dfu_alt_info ${dfu_alt_info_qspi}
=> dfu 0 sf 0:0
On host:
$ sudo dfu-util -l
$ sudo dfu-util -D MLO -a MLO
$ sudo dfu-util -D u-boot.img -a u-boot.img
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
On T1040D4RDB board, u-boot fails to connect port FM1@DTSEC3 to
the Ethernet PHY because the wrong PHY address is used. Also,
T1040D4RDB supports SGMII on one port only.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This commit adds additional file with implementation of board
detection code for Odroid-XU3/XU4.
The detection depends on compatible found in fdt:
- "samsung,exynos5" - uses Exynos5 generic code
- "samsung,odroidxu3" - try detect XU3 revision
There are few revisions of Odroid XU3/XU4, each can be detected
by checking the value of channel 9 of built-in ADC:
Rev ADC Board
0.1 0 XU3 0.1
0.2 372 XU3 0.2 | XU3L - no DISPLAYPORT
0.3 1280 XU4 0.1
The detection code depends on the ADC+10% value.
Implementation of functions:
- set_board_type() - read ADC and set type
- get_board_rev() - returns board revision: 1..3
- get_board_type() - returns board type string
Additional functions with return values of bool:
- board_is_generic() - true if found compatible "samsung,exynos5"
but not "samsung,odroidxu3"
- board_is_odroidxu3() - true if found compatible "samsung,odroidxu3"
and one of XU3 revision.
- board_is_odroidxu4() - true if found compatible "samsung,odroidxu3"
and XU4 revision.
After I2C controller init, the get_board_type() can check
if the XU3 board is a "Lite" variant, by probing chip
0x40 on I2C0 (INA231 - exists only on non-lite).
This is useful for setting fdt file name at misc_init_r().
Enabled configs:
- CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
- CONFIG_ODROID_REV_AIN
- CONFIG_REVISION_TAG
- CONFIG_BOARD_TYPES
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
As sama5 board has 32k sram size, so the at91bootstrap and spl for sama5
boards is bigger than 16k (0x4000). That will overlap the U-Boot
environment. So I move environment to 0x6000. And reduce its size as
well.
Following shows the size of the spl binaries (v2015.04 vs v2015.07):
% ls v2015.04/*spi*spl.bin -l | awk '{print $5,$(NF)}'
15540 v2015.04/at91sam9n12ek_spiflash_defconfig_u-boot-spl.bin
15704 v2015.04/at91sam9x5ek_spiflash_defconfig_u-boot-spl.bin
16064 v2015.04/sama5d3xek_spiflash_defconfig_u-boot-spl.bin
16304 v2015.04/sama5d4ek_spiflash_defconfig_u-boot-spl.bin
16304 v2015.04/sama5d4_xplained_spiflash_defconfig_u-boot-spl.bin
% ls v2015.07/*spi*spl.bin -l | awk '{print $5,$(NF)}'
16136 v2015.07/at91sam9n12ek_spiflash_defconfig_u-boot-spl.bin
16300 v2015.07/at91sam9x5ek_spiflash_defconfig_u-boot-spl.bin
16664 v2015.07/sama5d3xek_spiflash_defconfig_u-boot-spl.bin
16904 v2015.07/sama5d4ek_spiflash_defconfig_u-boot-spl.bin
16904 v2015.07/sama5d4_xplained_spiflash_defconfig_u-boot-spl.bin
The gcc version is: gcc 4.7.3 (Ubuntu/Linaro 4.7.3-12ubuntu1)
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Bo Shen <voice.shen@gmail.com>
As more features are added for SD boot on LS1021A QDS board,
the size of U-Boot is larger. CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS
needs to be adjusted to a suitable value.
Starting address of the malloc pool used in SPL needs to be
adjusted too, or it will occupy the address u-boot loads.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
I2C1 can work on ls102xa rev2.0 SD boot, so add
ID EEPROM for SD boot.
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Rework unified section macro select via Kconfig option
instead of macro definition in mx7_common header file.
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
Add i.MX6DQP-Sabresd board support:
1. set fdt_file according to board_rev which is set at runtime.
2. Add mx6dqp_ddr_ioregs and calibration value for this board.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
This macro is not needed, since gd->ram_size is assigned value using
function imx_ddr_size().
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Linux only boots IMX.51-based boards with device tree, so this board
would benefit from supporting it.
Signed-off-by: Damien Riegel <damien.riegel@savoirfairelinux.com>
Cc: Stefano Babic <sbabic@denx.de>
As 3G/1G user/kernel memory split is used on LS1021A, the Linux kernel
fails to access the device tree blob on boot. The reason is that u-boot
relocates the device tree blob into high memory when booting the kernel
and the kernel is unable to access the blob.
To avoid this issue, fdt_high is set to the value of 0xffffffff. The
device tree blob will not get relocated and is still in low memory to
make it accessible to the kernel.
For the same reason, initrd_high is set to the value of 0xffffffff too.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After the secondary cores enter U-Boot, use CONFIG_ARMV8_MULTIENTRY to
make secondary cores excute in spin loop.
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds esdhc support for ls1043ardb.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1043ARDB Specification:
-------------------------
Memory subsystem:
* 2GByte DDR4 SDRAM (32bit bus)
* 128 Mbyte NOR flash single-chip memory
* 512 Mbyte NAND flash
* 16 Mbyte high-speed SPI flash
* SD connector to interface with the SD memory card
Ethernet:
* XFI 10G port
* QSGMII with 4x 1G ports
* Two RGMII ports
PCIe:
* PCIe2 (Lanes C) to mini-PCIe slot
* PCIe3 (Lanes D) to PCIe slot
USB 3.0: two super speed USB 3.0 type A ports
UART: supports two UARTs up to 115200 bps for console
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
There are two LS series processors are built on ARMv8 Layersacpe
architecture currently, LS2085A and LS1043A. They are based on
ARMv8 core although use different chassis, so create fsl-layerscape
to refactor the common code for the LS series processors which also
paves the way for adding LS1043A platform.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Config Security Level Register is different between different SoCs,
so put the CSL register definition into the arch specific directory.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: Hou Zhiqiang <B48286@freescale.com>
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For most PPC platforms, they will call the first get_clocks() in
init_sequence_f[] as they define CONFIG_PPC. CONFIG_SYS_FSL_CLK is
then defined to call the second get_clocks(), which should be
redundant for PPC.
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board has not compiled for me for quite some time due to size
constraints, remove.
Cc: John Otken <jotken@softadvances.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As QSPI and IFC are pin-multiplexed on LS1021A, only IFC is supported in
SD boot now. For the customer's demand, QSPI needs to be supported in SD
boot too.
This patch adds QSPI or IFC support in SD boot according to the
corresponding defconfig. For detail, ls1021atwr_sdcard_ifc_defconfig is
used to support IFC in SD boot and ls1021atwr_sdcard_qspi_defconfig is
used to support QSPI in SD boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This will allow OF-based earlycon to be used once the appropriate
aliases are added to the device tree and kernel support is fixed.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define CONFIG_SYS_SPI_ARGS_OFFS, CONFIG_SYS_SPI_ARGS_SIZE
and CONFIG_SYS_SPI_KERNEL_OFFS which will be used in SPL
spi mode. These macros defines the device tree offset, size
and the kernel image offset in flash respectively.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
