Update the configuration files to support the device tree and driver
model. The device clock and pins configuration are handled by the
clock and the pinctrl drivers respectively.
Because the limitation of internal SRAM size, the SPL with driver
model can't be supported, disable the SPL option.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Due to the pin configuration and clock enabling is handling by the
driver, remove the unneeded hardcode uart1 init during
board_early_init_f stage.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Because the MACB driver supports the driver model and device tree,
the pins configuration and clock enabling are handled by the
pinctrl driver and clock driver, remove this hardcoded init code.
The USB Ether init code is removed as well.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
With gcc-6 we see a warning that sysclk_tbl is defined but unused, so
remove it.
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
In non DM I2C read operations the address length passed in during a read
operation will be used automatically. However, in DM I2C the address length
is set to a default value of one which causes problems when trying to
perform a read with a differing alen. Therefore, before the first read in a
series of read operations set the alen to the correct value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reading from the I2C EEPROM used typically requires using an address length
of 2. However, when using DM for I2C the default address length used is 1.
To fix this introduce a new function that allows the address length to be
changed. The logic to do so was copied from cmd/i2c.c.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
One some keystone2 platforms like K2G ICE, there is an option
to switch between 24MHz or 25MHz as sysclk. But the existing
driver assumes it is always 24MHz. Add support for getting
all reference clocks dynamically by reading boot pins.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G supports various sysclk frequencies which can be
determined using sysboot pins. PLLs should be configured
based on this sysclock frequency. Add PLL configurations
for all supported sysclk frequencies.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Instead of defining command options in every defconfig,
define a common Kconfig symbol that consolidates all command
options that are supported by any TI platform. Also use imply
keyword so that that specific option can be disabled if
not required.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The IGEP SMARC AM335x is an industrial processor module with
following highlights:
o AM3352 TI processor (Up to AM3359)
o Cortex-A8 ARM CPU
o SMARC form factor module
o Up to 512 MB DDR3 SDRAM / 512 MB FLASH
o WiFi a/b/g/n and Bluetooth v4.0 on-board
o Ethernet 10/100/1000 Mbps and 10/100 Mbps controller on-board
o JTAG debug connector available
o Designed for industrial range purposes
Signed-off-by: Pau Pajuelo <ppajuelo@iseebcn.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
Convert IGEP board to use UBI volumes for U-Boot, its environment and
kernel. With exception of first four sectors read by SoC BootROM whole
NAND is UBI managed.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Heiko Schocher<hs@denx.de>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
Rename igep0033 to igep003x as IGEP SMARC AM335x module (igep0034)
can use the same source files.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Pau Pajuelo <ppajuel@gmail.com>
All discovery boards have one user button & one user LED. Here we are
just reading the button status & switching ON the user LED.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
With this gpio driver supporting DM, there is no need to enable clocks
for different gpios (for pin muxing) in the board specific code.
Need to increase the allocatable area required before relocation from 0x400 to
0xC00 becuase of 10 new gpio devices(& new gpio class) added in device tree.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch also removes the sdram/fmc clock enable from board specific
code.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
As driver model takes care of pin control configuraion, this patch also
removes the sdram/fmc pin configuration.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
cc: Christophe KERELLO <christophe.kerello@st.com>
Invoke enable_usb_clocks during board_usb_init and disable_usb_clocks
during board_usb_exit to enable and disable clocks respectively.
Modifications:
* Enable USB clocks in the OMAP version of the function
board_usb_init.
* Disable USB clocks in the OMAP version of the function
board_usb_cleanup.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
A weak version of the function board_usb_init is implemented in:
common/usb.c
drivers/usb/host/xhci-omap.c
To fix the double implementations:
* Convert the board_usb_init function in drivers/usb/host/xhci-omap.c
normal (not weak).
* The function board_usb_init in drivers/usb/host/xhci-omap.c calls to
the weak function omap_xhci_board_usb_init.
* Rename board version of the function board_usb_init to
omap_xhci_board_usb_init.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
To achieve the same flexibility with the function board_usb_cleanup:
* Add a normal (not weak) implementation of the function
board_usb_cleanup in drivers/usb/host/xhci-omap.c
* The function board_usb_cleanup in drivers/usb/host/xhci-omap.c calls
to the weak function omap_xhci_board_usb_cleanup.
* Rename board version of the function board_usb_cleanup to
omap_xhci_board_usb_cleanup.
Done only for boards that defines CONFIG_USB_XHCI_OMAP.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
The logical expression to check the dtb is incorrect in
load_devicetree.
The problem was indicated by cppcheck.
The inconsistent variable name dtppart is changed to dtbpart.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Banana Pi M2 Plus is an Allwinner H3-based SBC by Sinovoip, which has
already mainline device tree file that have landed into U-Boot source
tree.
Add a defconfig file for it and add the MAINTAINERS items.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
For the consistent location of SoC-level Kconfig.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Mention eMMC and microSD as supported devices.
They have been enabled with patch
d0c5c8d529
odroid-c2: enable new Meson GX MMC driver in board defconfig
which was accepted for u-boot-mmc.git.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add warp7_secure_defconfig entry to avoid the following warning:
WARNING: no maintainers for 'warp7_secure'
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
This converts the following to Kconfig:
CONFIG_CMD_BLOB
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Add imply CMD_BLOB under CHAIN_OF_TRUST]
Signed-off-by: Tom Rini <trini@konsulko.com>
This is only used by one board and should not be a CONFIG option. Instead
it should use the driver model pmic framework. For now, just move the
setting into the only board that uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds support for HDMI output.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commits enable DM I2C support for A64/H3/H5 SoCs.
It is not enabled globaly for all sunxi SoCs, because some boards use
PMICs which are connected through I2C. In order to keep same
functionality, PMIC drivers needs to be ported to DM too.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.
Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.
Commit is based on the previous patch made by Philipp Tomsich
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This commit only moves i2c_init_board() function almost to the top and
doesn't have any functional changes.
This is needed for a temporary workaround in next commit when support
for DM I2C will be introduced.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As per the DM[1] Dated June 2016–Revised February 2017, Table 5-3,
DRA71 supports the following OPPs for various voltage domains:
VDD_MPU: OPP_NOM
VDD_CORE: OPP_NOM
VDD_GPU: OPP_NOM
VDD_DSPEVE: OPP_NOM, OPP_HIGH
VDD_IVA: OPP_NOM, OPP_HIGH
This patch add support for selection of the above OPPs instead of
using OPP_NOM for all voltage domains.
[1] http://www.ti.com/lit/ds/symlink/dra718.pdf
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for the Terasic DE10-Nano board. The board
is based on the DE0-Nano-Soc board but adds a larger FPGA
and an HDMI output.
Signed-off-by: Dalon Westergreen <dwesterg@gmail.com>
Reviewed-by: Dinh Nguyen <dinguyen@kernel.org>
Commit 088454cd dropped return value from initram(), setting
gd->ram_size directly. Three boards were missed for SPL boot.
Signed-off-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The PPA is a EL3 firmware, which support PSCI, hotplug,
power-management features etc.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Since commit ce412b7, RGMII TX clock internal delay is not enabled
for AR8033 unconditionally. On LS1021ATWR board, the third port
eTSEC3 uses AR8033 in RGMII mode. The TX/RX internal delay needs to
be enabled.
This patch will set PHY_INTERFACE_MODE_RGMII_ID to enable RGMII TX/RX
clock internal delay for AR8033 on the third port.
Signed-off-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Lichee Pi Zero is a development board with a V3s SoC, which features
64MiB DRAM co-packaged within the SoC, a TF slot, a SPI NOR slot (not
soldered in production batch), a 40-pin RGB LCD connector and some extra
pins available as 2.54mm pins or stamp holes.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Basic U-Boot support is now present for V3s.
Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.
As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This is needed for HDMI, which will be added later.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The Bananapi M2 Ultra is the first publicly available development board
featuring the R40 SoC.
This patch add barebone dtsi/dts files for the R40 and Bananapi M2 Ultra,
as well as a defconfig for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40's CPU controls are a combination of sun6i and sun7i.
All controls are in the CPUCFG block, and it seems the R40 does not
have a PRCM block. The core reset, power gating and clamp controls
are grouped like sun6i.
Last, the R40 does not have a secure SRAM block.
This patch adds a PSCI implementation for CPU bring-up and hotplug
for the R40.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we can do DRAM initialization for the R40, we can enable
SPL support for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
These values were taken from the Banana Pi M2 Ultra fex file
found in the released vendor BSP. This is the only publicly
available R40 device at the time of this writing.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PIO is generally compatible with the A20, except that it routes the
full 8 bits and eMMC reset pins for mmc2.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 SoC uses the AXP221s in I2C mode to supply power.
Some regulator's common usages have changed, and also the recommended
voltage for existing usages have changed. Update the defaults to match.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.
The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.
The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we have some lines in board/sunxi/Kconfig that are very long.
These line either provide default values for a set of SoCs, or limit
some option to a subset of sunxi SoCs.
Fortunately Kconfig makes it easy to split them. The Kconfig language
document states
If multiple dependencies are defined, they are connected with '&&'.
This means we can split existing dependencies at "&&" symbols. This
applies to both the "depends on" lines and "if" expressions.
This patch splits them up to one symbol per line. This will make it
easier to add, remove, or modify one item at a time.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_MACPWR to Kconfig and update all the sunxi defconfigs
that used it in SYS_EXTRA_OPTIONS.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Convert the CONFIG_SATAPWR into kconfig.
Thanks to that, many SYS_EXTRA_OPTIONS can be removed from some
defconfigs.
Signed-off-by: Mylène Josserand <mylene.josserand@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As board-specific reset logic, it needs to issue reset signal
via CPLD when issuing 'reset' command in u-boot, this patch
solves the issue of reset command not working on T1024RDB.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1046ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size
as header is appended to u-boot image. So header will also be
copied from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for the
header.
- Reduce the size of CAAM driver for SPL Blobification functions
and descriptors, that are not required at the time of SPL are
disabled. Further error code conversion to strings is disabled
for SPL build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add NAND secure boot target for ls1043ardb.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- MACRO for CONFIG_BOOTSCRIPT_COPY_RAM is enabled to copy Bootscript
from NAND to DDR. Offsets for Bootscript on NAND and DDR have been
also defined.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
- Add SD secure boot target for ls1043ardb.
- Implement FSL_LSCH2 specific spl_board_init() to setup CAAM stream
ID and corresponding stream ID in SMMU.
- Change the u-boot size defined by a macro for copying the main
U-Boot by SPL to also include the u-boot Secure Boot header size as
header is appended to u-boot image. So header will also be copied
from SD to DDR.
- CONFIG_MAX_SPL_SIZE is limited to 90KB. SPL is copied to OCRAM
(128K) where 32K are reserved for use by boot ROM and 6K for secure
boto header.
- Error messages during SPL boot are limited to error code numbers
instead of strings to reduce the size of SPL image.
Signed-off-by: Vinitha Pillai-B57223 <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Signed-off-by: Ruchika Gupta <ruchika.gupta@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 4k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1046ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1046ardb/ls1046ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1046a_common.h & ls1046ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Using changes in this patch we were able to reduce approx 10k
size of u-boot-spl.bin image. Following is breif description of
changes to reduce SPL size:
1. Changes in board/freescale/ls1043ardb/Makefile to remove
compilation of eth.c and cpld.c in case of SPL build.
2. Changes in board/freescale/ls1043ardb/ls1043ardb.c to keep
only ddr_init and board_early_init_f funcations in case of SPL
build.
3. Changes in ls1043a_common.h & ls1043ardb.h to remove driver
specific macros due to which static data was being compiled in
case of SPL build.
4. Disable MMC driver from bieng compiled in case of SPL NAND
build and NAND driver from bieng compiled in case of SPL MMC build.
5. Remove I2C driver support from SPL in case of LS1043ARDB.
Signed-off-by: Vinitha Pillai <vinitha.pillai@nxp.com>
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The RK3399-Q7 SoM is a Qseven-compatible (70mm x 70mm, MXM-230
connector) system-on-module from Theobroma Systems, featuring the
Rockchip RK3399.
It provides the following feature set:
* up to 4GB DDR3
* on-module SPI-NOR flash
* on-module eMMC (with 8-bit interace)
* SD card (on a baseboad) via edge connector
* Gigabit Ethernet w/ on-module Micrel KSZ9031 GbE PHY
* HDMI/eDP/MIPI displays
* 2x MIPI-CSI
* USB
- 1x USB 3.0 dual-role (direct connection)
- 2x USB 3.0 host + 1x USB 2.0 (on-module USB 3.0 hub)
* on-module STM32 Cortex-M0 companion controller, implementing:
- low-power RTC functionality (ISL1208 emulation)
- fan controller (AMC6821 emulation)
- USB<->CAN bridge controller
Note that we use a multi-payload FIT image for booting and have
Cortex-M0 payload in a separate subimage: we thus rely on the FIT
image loader to put it into the SRAM region that ATF expects it in.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Fixed build warning on puma-rk3399:
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Fix build error with sama5d3_xplained_mmc:
Signed-off-by: Simon Glass <sjg@chromium.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Remove CONFIG_PHY_MICREL as per previous patch:
Signed-off-by: Simon Glass <sjg@chromium.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Add back CONFIG_PHY_MICREL to prevent a build error:
Signed-off-by: Simon Glass <sjg@chromium.org>
The Vybrid SoC family has the same display controller unit (DCU)
like the LS1021A SoC. This patch adds platform data, pinmux defines
and clock control to enable the driver for Toradex Colibri Vybrid
module.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Rename CONFIG_FSL_DCU_FB to CONFIG_VIDEO_FSL_DCU_FB
and convert it to Kconfig.
Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Update the configuration files to support the device tree and driver
model, so do SPL. The device clock and pins configuration are handled
by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Enable the early debug UART to debug problems when an ICE or other
debug mechanism is not available.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Due to the introduction of the pinctrl and clk driver, and using
device tree files, remove the unneeded hardcoded pin configuration
and clock enabling code from the board file.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
Update the configuration files to support the device tree and
driver model, so do SPL. The device clock and pins configuration
are handled by the clock and the pinctrl drivers respectively.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Andreas Bießmann <andreas@biessmann.org>
The intention of the removal is the preparation to introduce the
new AT91 PIO pinctrl driver.
Use the union to make the PIO3 and PIO2's registers be together
and make their offset aligned.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This allows us to use the same DRAM init function on all archs. Add a
dummy function for arc, which does not use DRAM init here.
Signed-off-by: Simon Glass <sjg@chromium.org>
[trini: Dummy function on nios2]
Signed-off-by: Tom Rini <trini@konsulko.com>
This function name shadows a global name but is in fact different. This
is very confusing. Rename it to help with the following refactoring.
Signed-off-by: Simon Glass <sjg@chromium.org>
Logic PD has an i.MX6Q system on module (SOM) with a development kit. The
SOM has a built-in microSD socket, DDR and NAND flash. The development kit
has an SMSC Ethernet PHY, serial debug port and a variety of peripherals.
This have been verified to boot the i.MX6Q version over either SD
on the development kit or NAND built into the SOM. Items in the dtsi file
are specific to the SOM itself. Items in the dts file are in the baseboard.
Future versions of the SOM will come out supporting the same basebord and
potentially future base boards will come out supporting the same SOM.
Signed-off-by: Adam Ford <aford173@gmail.com>
Explain how to flash the eMMC and how to boot from it.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Apply the proper setting for the reserved bits in SetDes Test and System Mode Control register
to avoid the voltage peak issue while we do the IEEE PHY comformance test
Signed-off-by: Ken Lin <yungching0725@gmail.com>
Acked-by: Akshay Bhat <akshay.bhat@timesys.com>