Read RAM die capacity from the EEPROM TLV.
Follow the ONIE standard that defines the Vendor Extension entry type
for vendor specific data. We have no Private Enterprise Number at the
moment as the standard requires. Use the dummy all 0xff value for now.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV
stands for Type-Length-Value. The data format is described here:
https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format
Based on U-Boot patch from the Open Compute project:
ec87e872d4/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Enabled both DDR clock signals to support Clearfog variants (currently,
Clearfog GTR) that need both clocks.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/colibri-imx8x/colibri-imx8x.c:104:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/apalis-imx8/apalis-imx8.c:92:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c:110:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:129:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add prototype to function spl_board_boot_device to fix the following
sparse warning:
board/freescale/imx8mm_evk/spl.c:26:5: warning: no previous prototype
for ‘spl_board_boot_device’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Functions spl_dram_init() and power_init_board() are used only in
the scope of this file, so make them static to fix the following sparse
warnings:
board/freescale/imx8mm_evk/spl.c:40:6: warning: no previous prototype
for ‘spl_dram_init’ [-Wmissing-prototypes]
board/freescale/imx8mm_evk/spl.c:85:5: warning: no previous prototype
for ‘power_init_board’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Functions fracpll_configure(), decode_intpll(), decode_fracpll(),
get_root_src_clk() and get_root_clk() are used only in the scope of this
file, so make them static to fix the following sparse warnings:
arch/arm/mach-imx/imx8m/clock_imx8mm.c:50:5: warning: no previous
prototype for ‘fracpll_configure’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:271:5: warning: no previous
prototype for ‘decode_intpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:418:5: warning: no previous
prototype for ‘decode_fracpll’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:483:5: warning: no previous
prototype for ‘get_root_src_clk’ [-Wmissing-prototypes]
arch/arm/mach-imx/imx8m/clock_imx8mm.c:527:5: warning: no previous
prototype for ‘get_root_clk’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Add sys_proto.h header file to fix the following sparse warning:
board/freescale/imx8mm_evk/imx8mm_evk.c:59:5: warning: no previous
prototype for ‘board_mmc_get_env_dev’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The mux mode is embedded in the PAD definition and therefore there is
no need to repeat it in the PAD configuration value (more over since
this information will be masked out when the configuration value is
applied).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The imx8mm doesn't require the hdmi firmware.
Update also the fw version.
Signed-off-by: Flavio Suligoi <f.suligoi@asem.it>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
With commit 0d52bab462 ("mx7dsabre: Enable DM_ETH")
Device Tree has been update and change pfuze3000 node
Signed-off-by: Joris Offouga <offougajoris@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On SPL enabled systems, the current s_init code (wdog, clock and ldo
init) is executed twice (by SPL and u-boot). This is not necessary and
might lead to boot issues (ie, starting PMC1 when it is already running).
Signed-off-by: Jorge Ramirez-Ortiz <jorge@foundries.io>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently the following build warning is seen:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
===================================================
Since the mx7ulp-evk board does not have networking support, explicitly
disable networking.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add iMX6ULL VisionSOM SoM and VisionCB-RT-STD evaluation board support.
The SoM has an iMX6ULL, 512 MiB of DRAM and microSD slot. The carrier
board has Ethernet, USB host port, USB OTG port.
Signed-off-by: Arkadiusz Karas <arkadiusz.karas@somlabs.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The PFUZE100 and PFUZE200 PMICs can be discerned by bit 0 in DeviceID
register. Print the correct identification of the PMICs.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Simplify the uSDHC4 eMMC controller setup. This is the only eMMC
present on the system and only controller that is used, so drop
the extra logic.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Add slack to the clock frequency parameters passed to firmware within
clk_set_rate. min-freq is changed to 0 and max-rate is changed to
ULONG_MAX. This fixes certain issues with pll clock rounding when the
firmware is not able to set the frequency exactly to the target, the
current implementation fails if the available frequency is even 1Hz off
the target. With the change, the firmware still tries its best to set
the frequency as close as possible to the target.
Reported-by: Vishal Mahaveer <vishalm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Take over TI maintainership from Tom.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable USB keyboard to be used as input device at U-Boot prompt. Both
serial and USB keyboard will be active inputs simultaneously.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Enable configs related to USB Host mode, Peripheral mode and DFU.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add env variables that set up dfu_alt_info for MMC/EMMC/OSPI. This
is required to allow update of firmware on these media.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add pinmux for USB1 and enable it as a peripheral port in U-Boot
specific dtsi since U-Boot does not support OTG.
Disable USB0 as its not available on the baseboard.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add support for USB0 and USB1 instances on the AM6 SoC.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 SoC has USB2 PHY which is similar to existing USB2 PHYs on OMAP
SoCs. Add support for the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Below warning is seen when this driver is built for devices with 64 bit
physical address space.
drivers/phy/omap-usb2-phy.c: In function ‘omap_usb2_phy_probe’:
drivers/phy/omap-usb2-phy.c:187:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
priv->phy_base = (void *)base;
^
Fix this by using dev_read_addr_ptr() instead of dev_read_addr().
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM654 has DWC3 USB controller that is very similar to other TI SoCs. Add
a new compatible to enable the same.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
None of these boards boot, but the solution appears to be the same.
All the boards have SPL that is too large. With a few defconfig
options removed, these corresponding options can be removed from
their respective SPL dtb files.
This patch unifies the DM37/OMAP35 boards' -u-boot.dtsi files
to remove gpio's, i2c, bandgap, thermal zones, unneeded uarts, and
unneeded MMC nodes.
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently the DM37 and OMAP35 boards do not boot due to SPL
bring too large.
SPL doesn't need GPIO, I2C nor MMC sector access since it uses
a FAT file system.
This patch unifies all these boards to remove these unused features
from their defconfigs
Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add new defconfig files for the J721e High Security EVM.
These defconfigs are the same as for the non-secure part, except for:
CONFIG_TI_SECURE_DEVICE option set to 'y'
CONFIG_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_SPL_FIT_IMAGE_POST_PROCESS option set to 'y'
CONFIG_BOOTCOMMAND uses FIT images for booting
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
