At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
This patch adds the changes to boards.cfg and the board directory
under board/tqc.
TQMa6 is a family of modules based on Freescale i.MX6. It consists of
TQMa6Q (i.MX6 Quad), TQMa6D (i.MX6 Dual) featuring eMMC, and 1 GiB DDR3
TQMa6S (i.MX6 Solo) featuring eMMC and 512 MiB DDR3
The modules need a baseboard. Initially the MBa6x starterkit mainboard is
supported. To easy support for other mainboards the functionality is splitted
in one file for the module (tqma6.c) and one file for the baseboard (tqma6_
mba6).
The modules can be boot from eMMC (on USDHC3) and SPI flash.
The following features are supported:
- MMC: eMMC on module (on USDHC3) and SD-card (on MBa6x mainboard)
- Ethernet: RGMII using micrel KSZ9031 phy on MBa6x mainboard for TQMa6<x> module.
The phy needs special configurations for the pad skew registers to adjust for
the signal routing.
Also support for standard ethernet commands and uppdate via tftp.
- SPI: ECSPI1 with bootable serial flash on module and two additional
chip selects on MBa6x
- I2C: This patch adds support for the I2C busses on the TQMa6<x> modules (I2C3)
and MBa6x baseboards (I2C1). The LM75 temperature sensors on TQMa6<x> and MBa6x
are also configured.
- USB: high speed host 1 on MBa6x and support for USB storage
- PMIC: support for pfuze 100 on TQMa6<x>
Signed-off-by: Markus Niebel <Markus.Niebel@tq-group.com>
As a result of 0defddc851 , which did
a consolidation of the prompt string, this ifdef became empty. Remove
it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Stefano Babic <sbabic@denx.de>
- Fix base address of I2C2 as 0x118100 instead of 0x119000.
- Add definitions for I2C3 & I2C4.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On some platforms, CSn FTIM2.TCH is set to zero which is invalid,
an invalid hold time makes DUT timing variances, whether it works
or not on luck.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Since P1023RDS is no longer supported/manufactured by Freescale,
we clean up P1023RDS related code.
Since P1023RDB is still supported by Freescale,
we keep P1023RDB releated code.
Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Remove unnecessary condition CONFIG_RAMBOOT_PBL to
have SST and EON SPI flash work in case of NOR boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This board is close in binary size to one of its hard limits, so disable
SHA256 FIT image support to gain some breathing room.
Signed-off-by: Tom Rini <trini@ti.com>
This patch enables CONFIG_CMD_GPIO for the Allwinner (sunxi) platform as well
as providing the common gpio API (gpio_request/free, direction in/out, get/set
etc).
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ma Haijun <mahaijuns@gmail.com>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Henrik Nordström <henrik@henriknordstrom.net>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Similar to the USB NIC found on OMAP5uEVM, PandaBoard and BeagleBoard-XM
boards, the sunxi SoCs have a NIC onboard without an embedded MAC address.
Just like the omap used on these boards, the sunxi SoCs do have a unique chip
id, in the form of the 128 bit SID register:
http://linux-sunxi.org/SID_Register_Guide
So mimick the BeagleBoard-XM board code (commit 548a64d8) and use the chip id
to generate a unique fixed MAC address.
We check for the SID not being all 0, since some early A20 batches
shipped without having there SID programmed.
Note we use specific parts of the 128 bits, since some parts indicate the
SoC family / revision, and thus are fixed. The algorithm for this was taken
from the linux-sunxi.org kernels.
Signed-off-by: Jonathan Liu <net147@gmail.com>
[hdegoede@redhat.com: Expanded the commit message with some more info]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the x-powers axp209 pmic which is found on most A10, A13 and
A20 boards.
And enable AXP209 support for the Cubietruck and Cubieboard boards.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the i2c controller found on all Allwinner sunxi SoCs,
this is the same controller as found on the Marvell orion5x and kirkwood
SoC families, with a slightly different register layout, so this patch uses
the existing mvtwsi code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-By: Prafulla Wadaskar <prafulla@marvell.com>
Acked-by: Heiko Schocher <hs@denx.de>
[ ijc -- updated u-boot-spl-fel.lds ]
Note this has only been tested on Allwinner sunxi devices (support for which
gets introduced by a later patch).
The kirkwood changes have been compile tested using the wireless_space board
config, the orion5x changes have been compile tested using the edminiv2 board
config.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Heiko Schocher <hs@denx.de>
Timer on cyclone5 actually counts down. It took me a while to figure
out, as timer counting in wrong direction actually _can_ be used, it
just appears to tick at extremely high frequency in u-boot.
The bug was introduced in commit
23ab7ee0ff.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Adjust the mtdparts settings to allow for alternative boot images and
for using UBI.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
- "env ask", "env grep" and "setexpr" are needed for commissioning
- add support for ext4 file systems
- adjust default environment to use ext4 commands
- add write support for (V)FAT and EXT4
- add bitmap and splashscreen support
- print timestamp information for images
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
- "env ask", "env grep" and "setexpr" are needed for commissioning
- add support for ext4 file systems
- adjust default environment to use ext4 commands
- add write support for (V)FAT and EXT4
- add bitmap and splashscreen support
- print timestamp information for images
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The following patch re-enables the dhcp functionality on omap3_beagle.
It was removed with df4dbb5df6 when
omap3_beagle was converted to use ti_omap3_common.h. I have tested
beagleboard and beagleboard-xm with this patch and confirmed dhcp is
working.
Signed-off-by: Tyler Baker <tyler.baker@linaro.org>
Commit "2842c1c fit: add sha256 support" badly increased
memory footprint, so some of our boards did not build anymore.
Since monitor base must not be changed I removed some commands
to save memory.
Maybe making sha256 optional for fit would be an option for
the future since it really has some beefy footprint.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
The I2C bridge on DP501 supports EDID, MCCS and HDCP by default.
Allow EDID only to avoid I2C address conflicts.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
IHS I2C master support was merely a hack in the osd driver.
Now it is a proper u-boot I2C framework driver, supporting the
v2.00 master features.
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Use get_device_and_partition() is better since:
1. It will call the device initialize function internally. So we can
remove the mmc intialization code to save many lines.
2. It is used by fatls/fatload/fatwrite. So saveenv & load env should
use it too.
3. It can parse the "D:P", "D", "D:", "D:auto" string to get correct
device and partition information by run-time.
Also we remove the FAT_ENV_DEVICE and FAT_ENV_PART. We use a string:
FAT_ENV_DEVICE_AND_PART.
For at91sam9m10g45ek, it is "0". That means use device 0 and if:
a)device 0 has no partition table, use the whole device as a FAT file
system.
b)device 0 has partittion table, use the partition #1.
Refer to the commit: 10a37fd7a4 for details of device & partition string.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Add support for the Allwinner A13 and A10s SoCs also know as the Allwinner
sun5i family, and the A13-OLinuXinoM A13 based and r7-tv-dongle A10s based
boards.
The only differences compared to the already supported sun4i and sun7i
families are all in the DRAM controller initialization:
-Different hcpr values
-Different MBUS settings
-Some other small initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the Allwinner A10 SoC also known as the Allwinner sun4i family,
and add the Cubieboard board which uses the A10 SoC.
Compared to sun7 only the DRAM controller is a bit different:
-Controller reset bits are inverted, but only for Rev. A
-Different hpcr values
-No MBUS on sun4i
-Various other initialization changes
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The DMA code in sunxi_mmc.c is broken. mmc_trans_data_by_dma() allocates the
dma descriptors on the stack, and then exits while the dma transfer is in
progress, so the dma engine is reading stack memory which at that point may
be re-used. So far we've gotten away with this by luck, but recent u-boot
changes have shifted the stack start address by 16 bytes, which combined
with dma alignment now exposes this problem.
Since we end up just busy waiting for the dma engine anyway, this commit
fixes things by simply removing the dma code, resulting in smaller bug-free
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Turn on generic board for the integrators, as per the request in
the startup message. Everything just works, tested on the
Integrator/AP and Integrator/CP.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Simon Glass <sjg@chromium.org>
Scan Manager driver will be called to configure the IOCSR
scan chain. This configuration will setup the IO buffer settings
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Wolfgang Denk <wd@denx.de>
CC: Pavel Machek <pavel@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
To enable the DesignWare watchdog support at SOCFPGA
Cyclone V dev kit.
Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
This patch returns back support for old ep93xx processors family
Signed-off-by: Sergey Kostanbaev <sergey.kostanbaev@gmail.com>
Cc: albert.u.boot@aribaud.net
LS2085A is an ARMv8 implementation. This adds board support for emulator
and simulator:
Two DDR controllers
UART2 is used as the console
IFC timing is tightened for speedy booting
Support DDR3 and DDR4 as separated targets
Management Complex (MC) is enabled
Support for GIC 500 (based on GICv3 arch)
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
Signed-off-by: J. German Rivera <German.Rivera@freescale.com>
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@freescale.com>
The armv8 ARM Trusted Firmware (ATF) can be used to load various ATF
images and u-boot, and does this for virtual platforms by using
semihosting. This commit extends this idea by allowing u-boot to also
use semihosting to load the kernel/ramdisk/dtb. This eliminates the need
for a bootwrapper and produces a more realistic boot sequence with
virtual models.
Though the semihosting code is quite generic, support for armv7 in
fastmodel is less useful due to the wide range of available silicon
and the lack of a free armv7 fastmodel, so this change contains an
untested armv7 placeholder for the service trap opcode.
Please refer to doc/README.semihosting for a more detailed description
of semihosting and how it is used with the armv8 virtual platforms.
Signed-off-by: Darwin Rambo <drambo@broadcom.com>
Cc: trini@ti.com
Cc: fenghua@phytium.com.cn
Cc: bhupesh.sharma@freescale.com
With CONFIG_SYS_GENERIC_BOARD the board hangs after issuing a 'save' command.
Remove CONFIG_SYS_GENERIC_BOARD until this issue can be fixed properly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Since snow has a different memory configuration than peach, split the
configuration between the 5250 and 5420. Exynos 5420 supports runtime
memory configuration detection, and can make the determination between 4
and 7 banks at runtime.
Include the bank size with the number of banks for context to make the
number of banks meaningful.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Right now USB booting is enabled for Exynos5250 only. Moving all the
configs for USB boot mode from exynos5250-dt.h to exynos5-dt.h in order
to enableUSB booting for all Exynos5 SoCs.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Max footprint for SPL in both Exynos 5250 and 5420 is limited to 14 KB.
For Exynos5250 we need to keep it 14 KB because BL1 supports only fixed
size SPL downloading. But in case of Exynos5420 we need not restrict it
to 14 KB. And also, the SPL size for Exynos5420 is expected to increase
with the upcoming patches and the patches under review right now.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Currently environment resides at the location where BL2 ends.
This may hold good in case there is an empty space at this
position. But what if this place already has a binary or is
expected to have one. To avoid such scenarios it is better
to save environment at the end of the flash.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
While the Exynos5420 chip is used in both Smdk5420 and in the Peach-Pit
line of devices, there could be other boards using the same chip, so a
common configuration file is being added (exynos5420.h) as well
as two common device tree files (exynos54xx.dtsi & exynos5420.dtsi).
The peach board as declared in boards.cfg is a copy of smdk5420
declaration. The configuration files are similar, but define different
default device trees, console serial ports and prompts.
The device tree files for smdk5420 and peach-pit inherit from the same
common file.
Signed-off-by: Vadim Bendebury <vbendeb@chromium.org>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The u-boot Overo board actually supports both Overo (OMAP35xx)
and Overo Storm (AM/DM37xx) COMs with a range of different expansion
boards. This provides a mechanism to select the an appropriate device
tree file based on the processor version and, if available, the
expansion board ID written on the expansion board EEPROM. To match the
3.15+ kernels, fdtfile names have this format:
"omap3-overo[-storm]-<expansion board name>.dtb"
By default, we use "omap3-overo-storm-tobi.dtb".
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Conflicts:
include/configs/omap3_overo.h
AM43xx Starter Kit is a new board based on
AM437x line of SoCs. Being a low-cost EVM and
small size EVM are intended to provide an entry
level development platform on a full fledged
Hardware System.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move AEMIF driver to drivers/memory/ti-aemif.c along with AEMIF
definitions collected in arch/arm/include/asm/ti-common/ti-aemif.h
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.
Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
During bootm/z, U-Boot relocates the DTB and initrd to high memory so
they are out of the way of the kernel. On ARM at least, some parts of
high memory are "highmem" and can't be accessed at early boot. To solve
this, we need to restrict this relocation process to use lower parts of
RAM that area accessible.
For the DTB, an earlier patch of mine set CONFIG_SYS_BOOTMAPSZ. However,
since some platforms have different restrictions on DTB and initrd
location, that config option doesn't affect the initrd. We need to set
the initrd_high environment variable to control the initrd relocation.
Since we have carefully chosen the load addresses for the DTB and
initrd (see comments in include/configs/tegraNNN-common.h re: values in
MEM_LAYOUT_ENV_SETTINGS), we don't actually need any DTB or initrd
relocation at all. Skipping relocation removes some redundant work.
Hence, set both fdt_high and initrd_high to ffffffff which completely
disables relocation.
If the user does something unusual, such as using custom locations for
the DTB/initrd load address or wanting to use DTB/initrd relocation for
some reason, they can simply set these variables to custom values to
override these environment defaults.
With this change, cmd_sysboot works correctly for a filesystem created
by the Fedora installer.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
extlinux.conf is stored in /boot/extlinux/extlinux.conf rather than
/boot/extlinux.conf. Adjust Tegra's default boot scripts to use the
correct location. This change aligns Tegra's boot scripts with rpi_b.h
and also the location that the Fedora installer actually puts the file.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
We don't make use of the device tree otherwise yet (and will need to
think how to not break the current multi-board support) and this causes
further breakage with additional changes.
Signed-off-by: Tom Rini <trini@ti.com>
This is a MIME GnuPG-signed message. If you see this text, it means that
your E-mail or Usenet software does not support MIME signed messages.
The Internet standard for MIME PGP messages, RFC 2015, was published in 1996.
To open this message correctly you will need to install E-mail or Usenet
software that supports modern Internet standards.
Revert changes in iocon.h config file caused by
these two commits:
"configs: iocom: Fix typo on CMD_FPGA command"
(sha1: d0db28f940)
and
"fpga: Guard the LOADMK functionality with CMD_FPGA_LOADMK"
(sha1: 64e809afea)
CONFIG_CMD_FPGAD is own command.
Reported-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We need to run 'usb start' as preboot command so that ethernet comes up
during u-boot prompt.
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Up till now goni's configuration has been stored at OneNAND. Since u-boot
itself is now stored at eMMC it is more handy to store envs there as well.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
When building a target with CONFIG_ENV_IS_IN_SPI_FLASH the following
warning is seen:
include/configs/mx28evk.h:73:0: warning: "CONFIG_ENV_SIZE" redefined [enabled by default]
Protect the definition of CONFIG_ENV_SIZE to avoid the warning.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The name of the dtb file used in the kernel is 'imx6dl-riotboard.dtb', so fix
it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
mars and riot boards use UART2 as console, so CONFIG_CONSOLE_DEV should point
to 'ttymxc1' instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Iain Paton <ipaton0@gmail.com>
Commit e9fd66defd (ARM: mx6: define CONFIG_ARM_ERRATA_742230) enables
errata 742230 for imx6, because it helps remove one reboot issue.
However, this errata does not really apply on imx6, because Cortex-A9
on imx6 is r2p10 while the errata only applies to revisions r1p0..r2p2.
At a later time, commit f71cbfe3ca (ARM: Add workaround for Cortex-A9
errata 794072) adds support of errata 794072, which applies to all
Cortex-A9 revisions. As the workaround for both errata are exactly
same, it makes a lot more sense to select 794072 instead of 742230 for
imx6. Since we already enable 794072 for imx6, it's time to drop
errata 742230 to avoid confusion.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Nitin Garg <nitin.garg@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD for the Ethernut 5 board.
Signed-off-by: Tim Schendekehl <tim.schendekehl@egnite.de>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The current size of 1MB is not enough use to use DFU. Increase it for
ARMv7 boards, all of which should have 32MB or more SDRAM.
With this change it is possible to do 'dfu mmc 0' on a Beaglebone Black.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add QSPI support for VF610TWR, such as clock and iomux.
Signed-off-by: Alison Wang <Huan.Wang@freescale.com>
Signed-off-by: Chao Fu <b44548@freescale.com>
This family is supported by the TPS65218 PMIC. Implement a scale_vcores
to set the MPU and CORE voltage correctly to the max frequency that is
supported (and what we will be scaling them to in setup_dplls()).
Signed-off-by: Tom Rini <trini@ti.com>
in almost all cases we need the i2c commands within the u-boot shell.
So we enable them within the common section.
Cc: trini@ti.com
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
loadbootenv expects devtype variable to be set. This is missing in
mmcboot command. With this the following error comes:
U-Boot# run mmcboot
mmc0 is current device
SD/MMC found on device 0
** Bad device usb 0 **
** Bad device usb 0 **
Fixing this by setting devtype as mmc.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
commit a0a37183bd "ARM: omap: merge GPMC initialization code for
all platform" needs CONFIG_NOR, CONFIG_NAND or CONFIG_CMD_ONENAND
to be set to access flash. Add CONFIG_NAND for tam3517 derived
boards to prevent the following error: "nand: error: Unable to
find NAND settings in GPMC Configuration - quitting"
cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Currently PWREMU_MGMT is not configured in the Linux generic UART
driver as this register seems to be specific TI UART IP. So this
needs to be enabled in u-boot to use UART1 from kernel space.
Acked-By: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
With the changes to the i2c framework (and adopting the omap24xx_i2c
driver to them) we can no longer call i2c functions prior to gd having
been set and cleared. When SPL booting, this is handled by setting gd
to point to SRAM in s_init. However in the cases where we are loaded
directly by ROM (memory mapped NOR or QSPI) we need to make use of the
normal hooks to slightly delay these calls.
Signed-off-by: Tom Rini <trini@ti.com>
The ePOS EVM and EVM SK have QSPI as an option to boot. Add a qspiboot
target that utilizes QSPI for env and so forth as an example of best
practices. As QSPI is booted from directly we need to chang
CONFIG_SYS_TEXT_BASE.
Note that on ePOS EVM the QSPI and NAND are mutually exclusive choices
we need to handle that elsewhere, once NAND support is also added.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
OMAP3 used GPMC_NAND_ECC_LP_x8_LAYOUT and GPMC_NAND_ECC_LP_x16_LAYOUT macros
to configure GPMC controller for x7 or x8 bit device connected to its interface.
Now this information is encoded in CONFIG_SYS_NAND_DEVICE_WIDTH macro, so above
macros can be completely removed.
Signed-off-by: Pekon Gupta <pekon@ti.com>
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL: SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
which is called before probing for devices, hence any ONFI parameter
information is not available during GPMC initialization.
Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.
This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.
Signed-off-by: Pekon Gupta <pekon@ti.com>
Switch to an SPL image. The SPL for Ventana does the following:
- setup i2c and read the factory programmed EEPROM to obtain DRAM config
and model for board-specific calibration data
- configure DRAM per CPU/size/layout/devices/calibration
- load u-boot.img from NAND and jump to it
This allows for a single SPL+u-boot.img to replace the previous multiple boa
configurations.
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Add a common header which can hopefully be shared amon imx6 SPL users
Cc: Stefan Roese <sr@denx.de>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Andy Ng <andreas2025@gmail.com>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Tapani Utriainen <tapani@technexion.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Also update README.scrapyard.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Commit 3d5a335c announced that all the nand_spl boards
would be removed before v2014.07 release.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This is a workaround for 32 bit hardware limitation of TDM.
T1040 has 36 bit physical addressing, TDM DMAC register
are 32 bit wide but need to store address of CCSR space
which lies beyond 32 bit address range. This workaround
creats a LAW to enable access of TDM DMA to CCSR by
mapping CCSR to overlap with DDR.
A hole of 16M is created in memory using device tree. This
workaround law is set only if "tdm" is defined in hwconfig.
Also disable POST tests and add LIODN for TDM
Signed-off-by: Sandeep Singh <Sandeep@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- add support for 2nd DIMM slot.
- make it work with DIMM which is less than 2GB.
Verified with two 2GB UDIMM MT9JSF25672AZ-2G1K1 in two DIMM slots.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable legacy image format with CONFIG_IMAGE_FORMAT_LEGACY
on the ids8313 board, as it uses signed FIT images for booting
Linux and need the legacy image format.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: Michael Conrad <Michael.Conrad@ids.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Simon Glass <sjg@chromium.org>
make the use of legacy image format configurable through
the config define CONFIG_IMAGE_FORMAT_LEGACY.
When relying on signed FIT images with required signature check
the legacy image format should be disabled. Therefore introduce
this new define and enable legacy image format if CONFIG_FIT_SIGNATURE
is not set. If CONFIG_FIT_SIGNATURE is set disable per default
the legacy image format.
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Lars Steubesand <lars.steubesand@philips.com>
Cc: Mike Pearce <mike@kaew.be>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Simon Glass <sjg@chromium.org>
For each of Jetson TK1, Venice2, and Beaver:
- Enable the first USB controller in DT, and describe its configuration.
- Enable USB device/gadget support. This allows the user to type e.g.
"ums 0 mmc 0" at the command-line to cause U-Boot to act a USB device
implementing the USB Mass Storage protocol, and expose MMC device 0
that way.
This allows a host PC to mount the Tegra device's MMC, partition it, and
install a filesystem on it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Now that we wait the correct specification-mandated time at the end of
usb_hub_power_on(), I suspect that CONFIG_USB_HUB_MIN_POWER_ON_DELAY has
no purpose.
For cm_t35.h, we already wait longer than the original MIN_POWER_ON_DELAY,
so this change is safe.
For gw_ventana.h, we will wait as long as the original MIN_POWER_ON_DELAY
iff pgood_delay was at least 200ms. I'm not sure if this is the case or
not, hence I've CC'd relevant people to test this change.
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC82xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
This board has been orphan for a while.
(Emails to its maintainer have been bouncing.)
Because MPC8xx family is old enough, nobody would pick up
the maintainership on it.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denx <wd@denx.de>
The quad100hd has been unmaintained and dead ever since it's been
added some 6 years ago. Remove it.
Also update README.scrapyard and insert some commit IDs for removed
boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Gary Jennejohn <gljennjohn@googlemail.com>
The TPS65090 pmic chip can be on exynos5250 boards. Therefore,
select the appropriate config option for TPS65090 devices.
This commit should really use exynos5-dt.c, when it is available.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit be3b51aa did this mostly, but several have been added since. Do the
job again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Development board for headless gateway platform from Abilis Systems.
Initial commit with working UART and DW GMAC.
For now with generic Ethernet PHY due to problems in Realtek PHY driver.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Christian Ruppert <christian.ruppert@abilis.com>
Cc: Pierrick Hascoet <pierrick.hascoet@abilis.com>
In this configuration the environment will save in file: uboot.env of
mmc card.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Also we enable the mmc command in configuration file.
As both CONFIG_CMD_MMC and CONFIG_CMD_USB use the CONFIG_DOS_PARTITION,
so remove the redundant CONFIG_DOS_PARTITION definition.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
As at91 board config file will include the SoC header, so we can remove
the ARM926EJS definition in board config files.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Now the AT91FAMILY is already defined in the at91 SoC header. The at91
board config file will include the SoC header file.
So we can remove the redundant AT91FAMILY definition in at91 board
config files.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
[rebase patch]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following
warning on boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Tested-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
It supports boot from NAND and SD/MMC card.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Add support for booting from an MMC card.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Henrik Nordström <henrik@henriknordstrom.net>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
Add support for the GMAC Ethernet controller on Allwinner A20 (sun7i)
processors. Enable for the Cubietruck.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@ti.com>
This patch adds generic board, start of day and basic build system support for
the Allwinner A20 (sun7i) processor. This code will not been compiled until the
build is hooked up in a later patch. It has been split out to keep the patches
manageable.
Signed-off-by: Adam Sampson <ats@offog.org>
Signed-off-by: Aleksei Mamlin <mamlinav@gmail.com>
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Jens Kuske <jenskuske@gmail.com>
Signed-off-by: Luc Verhaegen <libv@skynet.be>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Patrick Wood <patrickhwood@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Reviewed-by: Tom Rini <trini@ti.com>
Move addresses for kernel, ramdisk and fdt blob to own variables. Add dtb
blob loading to all existing boot scripts, dtb filenames were taken from
vanilla kernel. Introduce new boot script bootcmd_legacy, which only loads
a kernel and a ramdisk. Make this the default boot script. This should also
restore the behaviour of the original bootloader.
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Michael Walle <michael@walle.cc>
cm-t54 Eth MAC address is stored in onboard EEPROM.
Add EEPROM support and setup stored Eth MAC address.
If EEPROM does not contain a valid MAC, then generate it from the
processor ID code (reference code is taken from OMAP5 uEvm board file).
Modify Device Tree blob MAC address field with retrieved data.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Tested-by: Samuel Egli <samuel.egli@siemens.com>
This adds the Gumstix DuoVero machine [1]. This is a OMAP4430-based
computer-on-module (COM aka SOM) that can be mounted on various
expansion boards with different peripherals.
[1] https://store.gumstix.com/index.php/category/43/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Rename gpmc_enable_gpmc_cs_config to gpmc_enable_gpmc_net_config]
Signed-off-by: Tom Rini <trini@ti.com>
Clean-up the board configuration file for the Gumstix Overo board by
including common omap3 definitions from ti_omap3_common.h as suggested
here [1].
[1] http://permalink.gmane.org/gmane.comp.boot-loaders.u-boot/185960
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Conflicts:
include/configs/omap3_overo.h
Update the board configuration for Gumstix Overo. In particular,
add support for zImage and DTB files on boot.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
Patch f33b9bd3
[arm: omap3: Enable clocks for peripherals only if they are used]
breaks SPL booting on Overo. Since some gpio inputs are
read to detect the board revision. But with this patch above, the
clocks to the GPIO subsystems are not enabled per default any more.
The GPIO banks need to be configured specifically now.
Signed-off-by: Ash Charles <ashcharles@gmail.com>
The linux kernel is at nand0,3 using the current layout, but is best
accessed through the partition label "linux". Since CONFIG_CMD_MTDPARTS is
defined the CONFIG_JFFS2 settings are unreferenced; use "setenv partition
rootfs" to set the default mtd partition for jffs2.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
Linux kernel at version 3.5 is about 3.5 MiB; test kernels for 3.10 exceed 4
MiB. Prepare for future upgrades by increasing the NAND partition now.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
The NAND linux partition format default was changed from jffs2 to ubi in
254973e6df but the corresponding commands were
not enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
Adapted from d70f5480 described below.
commit d70f54808d
Author: Javier Martinez Canillas <javier@dowhile0.org>
Date: Mon Jan 7 03:51:20 2013 +0000
omap4: allow the use of a plain text env file instead boot scripts
For production systems it is better to use script images since
they are protected by checksums and carry valuable information like
name and timestamp. Also, you can't validate the content passed to
env import.
But for development, it is easier to use the env import command and
plain text files instead of script-images.
Since both OMAP4 supported boards (Panda and TI SDP4430) are used
primarily for development, this patch allows U-Boot to load env var
from a text file in case that an boot.scr script-image is not present.
The variable uenvcmd (if existent) will be executed (using run) after
uEnv.txt was loaded. If uenvcmd doesn't exist the default boot sequence
will be started.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Tested-by: Ash Charles <ash@gumstix.com>
Since B&R boards uses only MMC-Controller #1, it only
wastes time if we initialize #0 first to see that there is nothing.
Cc: <trini@ti.com>
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Hannes Petermaier <oe5hpm@oevsv.at>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
This adds CONFIG_SYS_THUMB_BUILD to config, in order to enable optimization
of thumb.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Guard the LOADMK functionality with config to provide
an option to enable or disable it.
Enable it for all platforms in mainline which enable CONFIG_CMD_FPGA.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
The new 768KB u-boot image size requires changes for
SRIO/PCIE boot. These addresses need to be updated to
appropriate locations.
The updated addresses are used to configure the SRIO/PCIE
inbound windows for the boot, and they must be aligned
with the window size based on the SRIO/PCIE modules requirement.
So for the 768KB u-boot image, the inbound window cannot be set
with 0xfff40000 base address and 0xc0000 size, it should be
extended to 1MB size and the base address can be aligned with
the size.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
AFAICT, c=ffe does nothing and was a typo from the original commit
d17123696c "powerpc/p4080: Add support
for the P4080DS board" and just kept on getting duplicated
in subsequently added board config files.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Edward Swarthout <ed.swarthout@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In the earlier patches, the SPL/TPL fraamework was introduced.
For SD/SPI flash booting way, we introduce the SPL to enable a loader stub. The
SPL was loaded by the code from the internal on-chip ROM. The SPL initializes
the DDR according to the SPD and loads the final uboot image into DDR, then
jump to the DDR to begin execution.
For NAND booting way, the nand SPL has size limitation on some board(e.g.
P1010RDB), it can not be more than 4KB, we can call it "minimal SPL", So the
dynamic DDR driver doesn't fit into this minimum SPL. We added the TPL that is
loaded by the the minimal SPL. The TPL initializes the DDR according to the SPD
and loads the final uboot image into DDR,then jump to the DDR to begin execution.
This patch enabled SPL/TPL for P1_P2_RDB to support starting from NAND/SD/SPI
flash with SPL framework and initializing the DDR according to SPD in the SPL/TPL.
Because the minimal SPL load the TPL to L2 SRAM and the jump to the L2 SRAM to
execute, so the section .resetvec is no longer needed.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, CSPR and FTIM settings are
same as non-secure NAND boot. CSPR0 is configured as NAND and
CSPR1 is configured as NOR.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
P1020 SoC which has two USB controllers, but only first one is used
on this platform.
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T4160RDB shares the same platform as T4240RDB. T4160 is
a low power version of T4240, with the eight e6500 cores,
two DDR3 controllers, and same peripheral bus interfaces.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Proper adjustment for supporting DFU at GONI target has been made.
The s5p_goni.h file has been updated. Moreover the code for low level
USB initialization has been added to GONI board code.
The malloc pool has been enlarged in order to support larger buffer
sizes needed by DFU implementation.
Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Configuration file for GONI has been updated to support FAT file system,
new mmc partitioning scheme and read linux kernel from eMMC instead of
OneNAND.
Signed-off-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Tested-by: Arkadiusz Wlodarczyk <a.wlodarczyk@samsung.com>
Tested-by: Mateusz Zalega <m.zalega@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
SPL should load "u-boot-dtb.img" if both CONFIG_OF_CONTROL
and CONFIG_OF_SEPARATE are defined.
Otherwise, "u-boot.img" should be loaded.
Since CONFIG_OF_CONTROL is always undefined for SPL_BUILD,
the undef block should be moved below the conditional definition
of CONFIG_SPL_FAT_LOAD_PAYLOAD_NAME.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Moved the USB/SD/MMC common FAT configs separately
to avoid redefinition warnings.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added configs to support USB host for zynq boards.
Also added a command usbboot to boot from usb.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Extend max kernel image size. Gunzip is checking
this value. If kernel is larger, message below is shown.
Uncompressing Kernel Image ... Error: inflate() returned -5
GUNZIP: uncompress, out-of-mem or overwrite error -
must RESET board to recover
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This adds the Gumstix Pepper[1] single-board computer based on the
TI AM335x processor. Schematics are available [2].
[1] https://store.gumstix.com/index.php/products/344/
[2] https://pubs.gumstix.com/boards/PEPPER/
Signed-off-by: Ash Charles <ash@gumstix.com>
[trini: Move 'cdev' in board.c down to under #ifdef's where it's used]
Signed-off-by: Tom Rini <trini@ti.com>
The commits
commit b7b5f1a16c
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
da850evm, da850_am18xxevm: convert to CONFIG_SPL_MAX_FOOTPRINT
and
commit e7497891e3
Author: Albert ARIBAUD <albert.u.boot@aribaud.net>
cam_enc_4xx: convert to CONFIG_SPL_MAX_FOOTPRINT
replaced CONFIG_SPL_MAX_SIZE by CONFIG_SPL_MAX_FOOTPRINT. However,
CONFIG_SPL_MAX_SIZE is used in the Makefile for padding the SPL
when preparing an u-boot.ais image. By removing CONFIG_SPL_MAX_SIZE
said commits broke the ais image of the da850evm and cam_enc_4xx
configurations.
This patch converts the u-boot.ais target to use CONFIG_SPL_PAD_TO
instead of CONFIG_SPL_MAX_SIZE for padding the SPL and adds
a #define CONFIG_SPL_PAD_TO where it is required.
Signed-off-by: Christian Riesch <christian.riesch@omicron.at>
Reported-by: Tom Taylor <ttaylor.tampa@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Reviewed-by: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Fall back to previous dtb used when omap3-beagle-xm-ab.dtb doesn't exist in file system
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Acked-by: Tom Rini <trini@ti.com>
As of v3.15-rc3, omap3-beagle-xm-ab.dtb now exists with the usb hub (ehci) enabled.
For older kernels versions, cherry pick from mainline:
ef78f3869c37c480f1d58462a760a40dabc823f4
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
CC: Tom Rini <trini@ti.com>
CC: Nishanth Menon <nm@ti.com>
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
In order to have the same LED indication like in another product
when ready for updating, enable only red led and disable status
LED when entering DFU mode.
The status LED is only switched off when defined in board file.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
For dxr2 board DXR2_IOCTRL_VAL is set by data in EEPROM. In pxm2
board it does not make sense to have dxr2 as prefix. Replace it with
more meaningful DDR prefix.
Signed-off-by: Samuel Egli <samuel.egli@siemens.com>
Cc: Pascal Bach <pascal.bach@siemens.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
U-Boot on Tegra30 currently selects a main CPU frequency that cannot be
supported at all on some SKUs, and needs higher VDD_CPU/VDD_CORE values
on some others. This can result in unreliable operation of the main CPUs.
Resolve this by switching to a CPU frequency that can be supported by any
SKU. According to the following link, the maximum supported CPU frequency
of the slowest Tegra30 SKU is 600MHz:
repo http://nv-tegra.nvidia.com/gitweb/?p=linux-2.6.git;a=summary
branch l4t/l4t-r16-r2
path arch/arm/mach-tegra/tegra3_dvfs.c
table cpu_dvfs_table[]
According to that same table, the minimum VDD_CPU required to operate at
that frequency across all SKUs is 1.007V. Given the adjustment resolution
of the TPS65911 PMIC that's used on all Tegra30-based boards we support,
we'll end up using 1.0125V instead.
At that VDD_CPU, tegra3_get_core_floor_mv() in that same file dictates
that VDD_CORE must be at least 1.2V on all SKUs. According to
tegra_core_speedo_mv() (in tegra3_speedo.c in the same source tree),
that voltage is safe for all SKUs.
An alternative would be to port much of the code from tegra3_dvfs.c and
tegra3_speedo.c in the kernel tree mentioned above. That's more work
than I want to take on right now.
While all the currently supported boards use the same regulator chip for
VDD_CPU, different types of regulators are used for VDD_CORE. Hence, we
add some small conditional code to select how VDD_CORE is programmed. If
this becomes more complex in the future as new boards are added, or we
end up adding code to detect the SoC SKU and dynamically determine the
allowed frequency and required voltages, we should probably make this a
runtime call into a function provided by the board file and/or relevant
PMIC driver.
Cc: Alban Bedel <alban.bedel@avionic-design.de>
Cc: Marcel Ziswiler <marcel@ziswiler.com>
Cc: Bard Liao <bardliao@realtek.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
If CONFIG_API is ever to be enabled on Tegra, this define must be set,
since api/api_storage.c uses it.
A couple of annoyting things about CONFIG_SYS_MMC_MAX_DEVICE
1) It isn't documented in README. The same is true for a lot of similar
defines used by api_storage.c.
2) It doesn't represent MAX_DEVICE but rather NUM_DEVICES, since the
valid values are 0..n-1 not 0..n.
However, I this patch does not address those shortcomings.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This patch converts the following boards to use generic board: MPC8536DS,
MPC8572DS, MPC8641HPCN, p1_p2_rdb_pc, corenet_ds, t4qds, B4860QDS. It has
been tested on NOR boot on MPC8536DS, MPC8572DS, P1021RDB, P4080DS,
P5020DS, P5040DS, P3041DS, T4240QDS, B4860QDS.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Ying Zhang <b40530@freescale.com>
CC: Prabhakar Kushwaha <prabhakar@freescale.com>
CC: Haijun.Zhang <Haijun.Zhang@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
CC: Shaohui Xie <Shaohui.Xie@freescale.com>
U-boot image has grown and exceeded the predefined 512KB. Increasing to
768KB to align with other powerpc boards. Tested on MPC8572DS for 32-
and 36-bit targets with NOR flash boot. NAND boot is not covered by
this patch.
Also update board maintainer for these boards.
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
This prevents u-boot from accessing into the reserved memory areas that
we have for /var and the logbooks.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
This patch defines the post_hotkeys_pressed() function that is used for:
- triggering POST memory regions test
- starting the test application through the checktestboot command in
a script by setting the active bank to testbank
The post_hotkeys_pressed return the state of the SELFTEST pin.
The patch moves from the complete POST-memory test that is too long in
its SLOW version for our production HW test procedure to the much shorter
POST-memory-regions test.
Finally, the unused #defines for the not so relevant mtest command are
removed.
Signed-off-by: Stefan Bigler <stefan.bigler@keymile.com>
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
T4240RDB board Specification
----------------------------
Memory subsystem:
6GB DDR3
128MB NOR flash
2GB NAND flash
Ethernet:
Eight 1G SGMII ports
Four 10Gbps SFP+ ports
PCIe:
Two PCIe slots
USB:
Two USB2.0 Type A ports
SDHC:
One SD-card port
SATA:
One SATA port
UART:
Dual RJ45 ports
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: fix CONFIG_SYS_QE_FMAN_FW_ADDR in T4240RDB.h]
The fuse status register provides the values from on-chip
voltage ID efuses programmed at the factory.
These values define the voltage requirements for
the chip. u-boot reads FUSESR and translates the values
into the appropriate commands to set the voltage output
value of an external voltage regulator.
B4860QDS has a PowerOne ZM7300 programmable digital Power
Manager which is programmed as per the value read from
the fuses.
Reference for this code is taken from t4qds VID implementation.
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Enabling configs for GPIO CMD, EXYNOS4 family and replacing
exynos_gpio_get with new linear GPIO pin number required
because of the new function asking only 2 arguments (pin
and value) instead of 3 (bank, pin and value).
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Przemyslaw Marczak <p.marczak@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Adding two configs:
* CONFIG_FIT - Enable FIT image support.
* CONFIG_FIT_BEST_MATCH - Enable fetching correct DTB from
FIT image by comparing compatibles.
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Some new boards define CONFIG_SYS_HZ again! Remove.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Bo Shen <voice.shen@atmel.com>
bfin_gen_rand_mac() uses __DATE__ as the seed for random ethernet
address. This makes the build non-deterministic.
In the first place, it should not be implemented as a Bfin-specific
function. Use eth_random_addr() instead.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Some machines do not have SDL libraries installed, and it is still useful
to build sandbox without LCD/keyboard support.
Add an option for this, used as follows:
make sandbox_config all NO_SDL=1
Signed-off-by: Simon Glass <sjg@chromium.org>
This checks if the 7" WVGA produced by Future Eletronics is detected
and pass the needed kernel arguments for it to work.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This adds support for the 7" WVGA produced by Future Eletronics and
make it dynamically detect if it is connected or not based on the
touchscreen controller.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Acked-by: Stefano Babic <sbabic@denx.de>
The LTC3676 PMIC is used instead of the PFUZE100 PMIC on the
GW51xx/GW52xx/GW53xx Ventana baseboards. In order to support the IMX6Q SoC
at 1GHz on those baseboards, we need to adjust the voltage scaling for the SW1
and SW3 DC/DC converters on the LTC3676 for 1225mV. Note that the scalar
values for the LTC3676 are board-specific as they relate to a resistor devider
chosen by the board design.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
"mmc boot" command didn't use anywhere.
It can be replace "mmc dev" command.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the fe60164 commit.
This commit restores proper setting of default console for the
trats board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
During providing device tree support for Exynos4 based boards,
a tiny mistake has creeped in the 1ecab0f commit.
This commit restores proper setting of default console for the
trats2 board.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
- expand the condition with CONFIG_OF_CONTROL
Signed-off-by: Stephan Linz <linz@li-pro.net>
Acked-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Future patches will make DFU too large to fit in this board's SPL build.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Tom Rini <trini@ti.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Previously offsets handled by dfu_fill_entity_mmc(), defined in boards'
CONFIG_DFU_ALT were treated as hexadecimal regardless of their prefix,
which sometimes led to confusion. This patch forces usage of explicit
numerical base prefixes.
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Cc: Tom Rini <trini@ti.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Former usb_cable_connected() patch broke compilation of boards which do
not support this feature.
I've renamed usb_cable_connected() to g_dnl_usb_cable_connected() and added
its default implementation to gadget downloader driver code. There's
only one driver of this kind and it's unlikely there'll be another, so
there's no point in keeping it in /common.
Previously this function was declared in usb.h. I've moved it, since
it's more appropriate to keep it in g_dnl.h - usb.h seems to be intended
for USB host implementation.
Existing code, confronted with default -EOPNOTSUPP return value,
continues as if the cable was connected.
CONFIG_USB_CABLE_CHECK was removed.
Change-Id: Ib9198621adee2811b391c64512f14646cefd0369
Signed-off-by: Mateusz Zalega <m.zalega@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Since highbank is actually shared between Highbank and Midway platforms,
remove the Highbank name from the prompt and use the default.
Signed-off-by: Rob Herring <robh@kernel.org>
mx6slevk has a m25p32 SPI NOR flash connected to ESCSPI port.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Enable CONFIG_SYS_GENERIC_BOARD, so that we get rid of the following warning on
boot:
"Warning: Your board does not use generic board. Please read
doc/README.generic-board and take action. Boards not
upgraded by the late 2014 may break or be removed."
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
MACH_TYPE_LAGER and CONFIG_MACH_TYPE are not already available on Lager board.
This removes them.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_SH_TMU_CLK_FREQ of lager is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CONFIG_SH_TMU_CLK_FREQ of koelsch is calculated from the external clock.
This defines RMOBILE_XTAL_CLK, this updates the calculation of
CONFIG_SH_TMU_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Lagar board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Koelsch board has NOR-Flash. But user uses SPI-Flash ROM instead of NOR-Flash.
This removed the setting of NOR-Flash.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
With 32 milliseconds delay on some boards EEMPROM got written inconsistently.
With 64 msec all of our existig boards show properly written EEPROM.
Cc: Tom Rini <trini@ti.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Add support of 2 stage NAND/SD boot loader using SPL framework.
PBL initialise the internal SRAM and copy SPL, this further
initialise DDR using SPD and environment and copy u-boot from
NAND/SD to DDR, finally SPL transfer control to u-boot.
NOR uses CS1 instead of CS2 when NAND boot, fix it.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
- update readme.
- add CONFIG_SYS_CORTINA_FW_IN_* for loading Cortina PHY CS4315
ucode from NOR/NAND/SPI/SD/REMOTE.
- update cpld vbank with SW3[5:7]=000 as default vbank0 instead of
previous SW3[5:7]=111 as default vbank.
- fix CONFIG_SYS_I2C_EEPROM_ADDR_LEN to 2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768K) from SPI/SD/NAND to DDR, finally SPL transfers control
to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2-stage NAND/SPI/SD boot loader using SPL framework.
PBL initializes the internal CPC-SRAM and copy SPL(160K) to it,
SPL further initializes DDR using SPD and environment and copy
u-boot(768 KB) from SPI/SD/NAND to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: fix boards.cfg for T2081QDS_SDCARD and _SPIFLASH]
Reviewed-by: York Sun <yorksun@freescale.com>
u-boot binary size for Freescale mpc8536DS platforms is 512KB.
This has been reached to upper limit of the platforms and causig
linker error. So increase the u-boot binary size to 768KB.
Signed-off-by: Haijun Zhang <Haijun.Zhang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
U-boot binary size has been increased from 512KB to 768KB.
So update CONFIG_SYS_MONITOR_LEN to reflect the same.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND, SD, SPI boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add support of 2 stage NAND boot loader using SPL framework.
here, PBL initialise the internal SRAM and copy SPL(160KB). This further
initialise DDR using SPD and environment and copy u-boot(768 KB) from NAND to DDR.
Finally SPL transer control to u-boot.
Initialise/create followings required for SPL framework
- Add spl.c which defines board_init_f, board_init_r
- update tlb and ddr accordingly
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB_PI board does not have QE connector.
So disable CONFIG_QE and CONFIG_U_QE for T1042RDB_PI
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB and T1042RDB_PI has CPLD. Here CPLD controls board mux/features.
This support of CPLD includes
- files and register defintion
- Commands to swtich alternate bank and default bank
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
We use dynamical mtdparts partition instead of directly puting
mtd partitions nodes in device tree.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040RDB, T1042RDB header files are very similar so merged into new header file T104xRDB.
T104xRDB header file can support both T1040RDB and T1042RDB_PI header.
Patch makes following changes
-Update Boards.cfg file for T1040RDB and T1042RDB_PI
-Add new T104xRDB header file
-Delete T1040RDB, T1042RDB_PI header file
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
NOR flash is on CS1 instead of CS2 when NAND boot.
So correct NOR chip selection to CS1 from CS2.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1040QDS_D4 is a variant of T1040QDS, with additional circuit to support
DDR4 memory. Tested with MTA9ASF51272AZ-2G1AYESZG.
Signed-off-by: York Sun <yorksun@freescale.com>
add CONFIG_QE, CONFIG_U_QE and CONFIG_SYS_QE_FW_ADDR into
"include/configs/T1040RDB.h"
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_QE_FMAN_FW_ADDR is used to both Fman and QE for microcode address.
Now using CONFIG_SYS_FMAN_FW_ADDR for Fman microcode address,
and CONFIG_SYS_QE_FW_ADDR for QE microcode address.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add NOR, SPI and SD secure boot targets for BSC9132QDS.
Changes:
- Debug TLB entry is not required for Secure Boot Target.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The workaround for IFC errata A003399 was not enabled
in case of secure boot. So, secure boot from NOR was not
working.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
In case of secure boot from NAND, the DDR is initialized by the
BootROM using the config words (CF_WORDS) in the CF_HEADER
and u-boot image is copied from NAND to DDR by the BootROM.
So, CONFIG_SYS_RAMBOOT has been defined for Secure Boot from NAND.
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For KVM we have a special PV machine type called "ppce500". This machine
is inspired by the MPC8544DS board, but implements a lot less features
than that one.
It also provides more PCI slots and is supposed to be enumerated by
device tree only.
This patch adds support for the generic ppce500 machine and tries to
rely solely on device tree for device enumeration.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This is dead hardware and no one is interested in making the
necessary changes for upcoming features like generic board or
driver model.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
This patch converts the MIPS Malta development board to make use of the
generic board code now that it is supported on MIPS.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/lubbock/*
- Remove include/configs/lubbock.h
- Cleanup defined(CONFIG_LUBBOCK)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove include/configs/EVB64260.h
- Remove the entry from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/mousse/*
- Remove include/configs/MOUSSE.h
- Clean-up defined(CONFIG_MOUSSE)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rsdproto/*
- Remove include/configs/rsdproto.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/rpxsuper/*
- Remove include/configs/RPXsuper.h
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/RPXlite/*
- Remove board/RPXClassic/*
- Remove include/configs/RPXlite.h
- Remove include/configs/RPXClassic.h
- Clean-up defined(CONFIG_RPXCLASSIC)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove include/configs/{ADS860.h,FADS823.h,FADS850SAR.h,FADS860T.h}
- Cleanup defined(CONFIG_ADS), defined(CONFIG_MPC823FADS),
defined(CONFIG_MPC850SAR), defined(CONFIG_SYS_DAUGHTERBOARD)
- Remove the entries from boards.cfg
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/genietv/*
- Remove include/configs/GENIETV.h
- Clean-up if defined(CONFIG_GENIETV)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since these boards were moved to Orphan. Remove.
- Remove board/mbx8xx/*
- Remove include/configs/{MBX.h,MBX860T.h}
- Clean-up if defined(CONFIG_MBX)
- Move the entries from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Enough time has passed since this board was moved to Orphan. Remove.
- Remove board/nx823/*
- Remove include/configs/NX823.h
- Clean-up ifdef(CONFIG_NX823)
- Move the entry from boards.cfg to doc/README.scrapyard
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
ti_omap3_common contains a lot of common header definitions that help
reduce the size of the zoom1 config file. So, use the generic header
and customize as needed for the platform (example: no spl).
Signed-off-by: Nishanth Menon <nm@ti.com>
This is more in line with commits
664979a2a9f764b63b8094458b87247d254b0cc1(omap3_beagle: remove JFFS2
support.) and 102ce9ea7a (omap3_beagle:
enable CMD_FS_GENERIC and simplify load of image/ramdisk)
CMD_FS_GENERIC allows us to simplify where we load up our image from
either from ext2/fat etc. So, lets use that instead of cumbersome
options we'd have to use. Sticking with existing conventions,
defaults will be:
bootfile=uImage
bootpart=0:1 (first partition)
bootdir=/ (/ in first partition)
Signed-off-by: Nishanth Menon <nm@ti.com>
CONFIG_SYS_GENERIC_BOARD should now be enabled for generic
functionality Further information in doc/README.generic-board
Signed-off-by: Nishanth Menon <nm@ti.com>