This commit adds initial support for the Toradex Apalis iMX8X 2GB WB
IT V1.1A System on Module support [1].
Boot log:
U-Boot 2020.10-02940-g894aebb7e8-dirty (Oct 22 2020 - 09:43:57 +0300)
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz at 30C
DRAM: 2 GiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... OK
In: serial@5a070000
Out: serial@5a070000
Err: serial@5a070000
Model: Toradex Apalis iMX8 QuadXPlus 2GB Wi-Fi / BT IT V1.1A,
Serial# 06617018
Net: eth0: ethernet@5b040000 [PRIME]
Hit any key to stop autoboot: 0
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet (*)
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
* With the SCU FW from the latest Toradex BSP 5.0.0 (SCU FW 1.5.1)
ETH PHY encounters bring up problems after reset, this will be fixed
soon on SCU FW side.
[1] https://www.toradex.com/computer-on-modules/apalis-arm-family/nxp-imx-8x
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
V1.1A HW switched the PMIC from BD71837 to PCA9450.
- Disable combined DVS in PCA9450_BUCK123_DVS.
- Increase DDR Voltage to 0.95V as we use a 1.5GHz RAM.
- Configure WDOG_B behaviour.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Removed aristainetos2, 2b, 2b-csl. This boards have been
recalled and destroyed.
Adapt board code to remove stuff not needed anymore.
Fix checkpatch warning, remove fdt_high and initrd_high
from default environment.
Signed-off-by: Heiko Schocher <hs@denx.de>
zu remove
Add DT for DH PicoITX unit, which is a bare-bones carrier board for
the DHCOM. The board has ethernet port, USB, CAN, LEDs and a custom
board-to-board expansion connector.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
Remove fixed configuration and detect flash based on DT.
Also increase amount of flash sectors to 2048 because on kc705 flash has
1027 sectors.
Bank # 1: CFI conformant flash (16 x 16) Size: 128 MB in 1027 Sectors
Intel Extended command set, Manufacturer ID: 0x89, Device ID: 0x8962
Erase timeout: 4096 ms, write timeout: 2 ms
Buffer write timeout: 5 ms, buffer size: 1024 bytes
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The PinePhone is a smartphone produced by Pine64, with an A64 SoC,
2 or 3 GiB LPDDR3 RAM, 16 or 32 GiB eMMC, 720x1440 MIPI-DSI panel,
and Quectel EG25-G modem.
There are two main board revisions: 1.1 for early adopters, and 1.2
for mass production. Since there is code to detect the board revision
at boot, one config/image can support both boards.
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
By default CONFIG_LOGLEVEL seems to be set to 4 which is
too low and doesn't show dev_info/dev_notice/dev_warn
messages on console. This has been deliberately set low
globally to be conservative setting across the board due to
primary bootloader size limitations. It is best to tune
per board config as per user needs.
On K3 we have separate SPL and u-boot configs so we
can afford to set u-boot CONFIG_LOGLEVEL to 7.
On AM65 this patch causes u-boot.img size to change from
932KB to 940KB with 1 line additional print during
MMC boot. i.e. details of Net subsystem
"Net: K3 CPSW: nuss_ver: 0x6BA00102 cpsw_ver: 0x6BA80102 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000"
Similar 8KB difference was seen on J721E.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Commit c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
added an alias spi1 referring to spi@ff1d0000, however there was already
an alias spi0 referring to the same node in rockpro64's u-boot.dtsi, and
having both aliases present broke booting from SPI flash for this board.
Remove the spi0 alias, set the default bus for SPI flash to 1, and
enable support for numbered aliases in SPL so that it uses the same bus
numbering as U-Boot proper. This fixes booting from U-Boot in SPI flash
on the rockpro64 board.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Commit fe97471632 ("rockchip: rk3288: Allow setting up clocks in
U-Boot proper") fixes some clock issues when chainloading U-Boot on
rk3288 chromebooks. Part of that change is still available in veyron's
board_early_init_r() function. Since chain-loading U-Boot proper from
vendor firmware is possible on gru boards as well, do the same thing for
them too.
On rk3399, this needs to detect whether SPL was run via handoff, so
enable that and bloblist kconfigs it needs for chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
- Add a new SMBIOS parser and enable it when booting from coreboot
- Fix up various driver names to avoid dtoc warnings
- Fully enable ACPI support on Google Chromebook Coral
- Add a way to set SMBIOS properties using the devicetree
- Update existing boards to use devicetree for SMBIOS using a new
default sysinfo driver
Now that we can use devicetree to specify this information, drop the old
CONFIG options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a file containing defaults for these, using the existing CONFIG
options. This file must be included with #include since it needs to
be passed through the C preprocessor.
Enable the driver for all x86 boards that generate SMBIOS tables.
Disable it for coral since it has its own driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: reword the commit message a little bit]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add settings and enable the default sysinfo driver so that these can come
from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This uclass is intended to provide a way to obtain information about a
U-Boot board. But the concept of a U-Boot 'board' is the whole system,
not just one circuit board, meaning that 'board' is something of a
misnomer for this uclass.
In addition, the name 'board' is a bit overused in U-Boot and we want to
use the same uclass to provide SMBIOS information.
The obvious name is 'system' but that is so vague as to be meaningless.
Use 'sysinfo' instead, since this uclass is aimed at providing information
on the system.
Rename everything accordingly.
Note: Due to the patch delta caused by the symbol renames, this patch
shows some renamed files as being deleted in one place and created in
another.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a script to boot Chrome OS from the internal MMC. This involved adding
a few commands and options.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present CONFIG_CHROMEOS is used to determine whether verified boot is
in use. The code to implement that is not in U-Boot mainline.
However, it is useful to be able to boot a Chromebook in developer mode
in U-Boot mainline without needing the verified boot code.
To allow this, use CONFIG_CHROMEOS_VBOOT to indicate that verified boot
should be used, and CONFIG_CHROMEOS to indicate that the board supports
Chrome OS. That allows us to define CONFIG_CHROMEOS on coral.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If u-boot gets used as coreboot payload it might be nice to get
vendor, model and bios version from smbios. I am not sure about
the output of all the read information.
With qemu target for coreboot this could look this:
CBFS: Found @ offset 14f40 size 3b188
Checking segment from ROM address 0xffc15178
Checking segment from ROM address 0xffc15194
Loading segment from ROM address 0xffc15178
code (compression=1)
New segment dstaddr 0x01110000 memsize 0x889ef srcaddr 0xffc151b0 filesize 0x3b150
Loading Segment: addr: 0x01110000 memsz: 0x00000000000889ef filesz: 0x000000000003b150
using LZMA
Loading segment from ROM address 0xffc15194
Entry Point 0x01110000
BS: BS_PAYLOAD_LOAD run times (exec / console): 77 / 1 ms
Jumping to boot code at 0x01110000(0x07fa7000)
U-Boot 2020.10-00536-g5dcf7cc590-dirty (Oct 07 2020 - 14:21:51 +0200)
CPU: x86_64, vendor AMD, device 663h
DRAM: 127.1 MiB
MMC:
Video: No video mode configured in coreboot!
Video: No video mode configured in coreboot!
Vendor: QEMU
Model: Standard PC (i440FX + PIIX, 1996)
Bios Version: 4.12-3152-g326a499f6f-dirty
Net: e1000: 52:54:00:12:34:56
eth0: e1000#0
No working controllers found
Finalizing coreboot
Hit any key to stop autoboot: 0
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
GE B1x5v2 patient monitor series is similar to the CARESCAPE Monitor
series (GE Bx50). It consists of a carrier PCB used in combination
with a Congatec QMX6 SoM. This adds U-Boot support using device model
everywhere and SPL for memory initialization.
Proper configuration is provided as 'ge_b1x5v2_defconfig' and the
combined image u-boot-with-spi.imx can be flashed directly to 1024
byte offset to /dev/mtdblock0. Alternatively SPL and u-boot.imx can
be loaded separately via USB-OTG using e.g. imx_usb.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
- New PX30 board: Engicam PX30.Core;
- Fix USB HID support for rock960;
- Remove host endianness dependency for rockchip mkimage;
- dts update for rk3288-tinker;
- Enable console MUX for some ROCKPi boards;
- Add config-based ddr selection for px30;
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
C.TOUCH 2.0 is a general purpose carrier board with capacitive
touch interface support.
PX30.Core needs to mount on top of this Carrier board for creating
complete PX30.Core C.TOUCH 2.0 board.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
PX30.Core is an EDIMM SOM based on Rockchip PX30 from Engicam.
EDIMM2.2 Starter Kit is an EDIMM 2.2 Form Factor Capacitive
Evaluation Board from Engicam.
PX30.Core needs to mount on top of this Evaluation board for
creating complete PX30.Core EDIMM2.2 Starter Kit.
Add support for it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Enable Console multiplexing in ROCKPi N8 which would is
required to video out the console buffer.
Enable it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Enable Console multiplexing in ROCKPi N10 which would is
required to video out the console buffer.
Enable it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
On aristianetos boards the display type is detected
through "panel" environment variable. Dependend on the
display type we detect the board type and this decides which
DTB we have to use for the board.
So we need early spi environment access.
Signed-off-by: Heiko Schocher <hs@denx.de>
Fix up USB config options so keyboards and other USB devices work.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Change-Id: I34b0696e0ac7303186f20c83278dde340399b690
Add a simple test that we can obtain the correct parent for an I2C
device. This requires updating the driver names to match the compatible
strings, adding them to the devicetree and enabling a few options.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a test in dtoc for this feature, but not one in U-Boot itself.
Add a simple test that checks that the information comes through
correctly.
Signed-off-by: Simon Glass <sjg@chromium.org>
- Armada 8k: Add NAND support via PXA3xx NAND driver (Baruch)
- Armada 8k: Use ATF serdes init instead of the "old" U-Boot version
(Baruch)
- Minor update to Octeon TX/TX2 defconfig (Stefan)
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCX5rH/QAKCRDKSWXLKUoM
IRPAAJ9SvHR3w1qTc5W+Q5CWBUH5wJbNYQCaA4PpqZCdvyu1+nF5luL6JHhbDgw=
=hOd7
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2021.01-v2' of https://gitlab.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2021.01-v2
common:
- Add support for 64bit loadables from SPL
xilinx:
- Update documentation and record ownership
- Enable eeprom board detection based legacy and fru formats
- Add support for FRU format
microblaze:
- Optimize low level ASM code
- Enable SPI/I2C
- Enable distro boot
zynq:
- Add support for Zturn V5
zynqmp:
- Improve silicon detection code
- Enable several kconfig options
- Align DT with the latest state
- Enabling security commands
- Enable and support FPGA loading from SPL
- Optimize xilinx_pm_request() calling
versal:
- Some DTs/Kconfig/defconfig alignments
- Add binding header for clock and power
zynq-sdhci:
- Add support for tap delay programming
zynq-spi/zynq-qspi:
- Use clock framework for getting clocks
xilinx-spi:
- Fix some code issues (unused variables)
serial:
- Check return value from clock functions in pl01x
