Add some tests which check the behaviour of uclass_first_device() and
uclass_next_device() when probing of a device fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for the gmac ethernet interface to pinctrl. This hardcodes
the setup to match that of the firefly and Radxa Rock2 boards, using the
RGMII phy mode for gmac interface and GPIO4B0 as the phy reset GPIO.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Use fixed regulator for sdmmc-pwren for sdmmc power.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phyCORE-RK3288 is a SoM (System on Module) containing a RK3288 SoC.
The module can be connected to different carrier boards.
It can be also equipped with different RAM, SPI flash and eMMC variants.
The Rapid Development Kit option is using the following setup:
- 1 GB DDR3 RAM (2 Banks)
- 1x 4 KB EEPROM
- DP83867 Gigabit Ethernet PHY
- 16 MB SPI Flash
- 4 GB eMMC Flash
Add basic support for the PCM-947 carrier board, a RK3288 based development
board made by PHYTEC. This board works in a combination with
the phyCORE-RK3288 System on Module.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add fixed regulator for the port of typec0 and typec1 to control vbus
instead of gpio.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable dwc2 controller and add fixed regulator for dwc2 controller to
control vbus.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The driver changes gpio to fixed regulator to control vbus, so add
fixed regulator node in DTS for xhci driver.
Signed-off-by: Meng Dongyang <daniel.meng@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Rockchip using the same bit definition for dram info and write
to os_reg, the col and bw info is not correct and let's fix it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
According to rk3288 spec, the pwm register order is:
PWM_PWM0_CNT,
PWM_PWM0_PERIOD_HPR,
PWM_PWM0_DUTY_LPR,
PWM_PWM0_CTRL
but the source code's order is:
struct rk3288_pwm {
u32 cnt;
u32 duty_lpr;
u32 period_hpr;
u32 ctrl;
};
So, correct it here. It is the same as RK3399.
Signed-off-by: Eric Gao <eric.gao@rock-chips.com>
Edited the commit message:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable sdmmc device and add the spl boot device sequence.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the 'clock-freq-min-max' is deprecated, we use max-frequency.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Enable soc support for SPL and U-boot skeleton.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The dts files are from kernel and with modify to adapt U-Boot.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The bank0 ram size should be the DRAM size minus reserved size,
the DRAM size may be 1GB, 2GB, 4GB, we can not hard code it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added DECLARE_GLOBAL_DATA_PTR for RK3328, RK3368 and RK3399:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add dmc node to enable sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a dmc node for sdram driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add sdram driver in U-Boot for get the correct sdram size from
sys_reg, so that U-Boot can co-work with Rockchip loader or SPL
to get different dram capability and then tell the kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add sdram driver in U-Boot for get the correct sdram size from
sys_reg, so that U-Boot can co-work with Rockchip loader or SPL
to get different dram capability and then tell the kernel.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Replace the sdram_init() in board init and rockchip_sdram_size() in
sdram driver for all the Rockchip SoCs which enable CONFIG_RAM.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Make dram_init() in rk3036-board.c conditional on CONFIG_RAM:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
There are some functions like sdram_size_mb can be re-used for
different rockchip SoCs, just put them into common file.
Add board_get_usable_ram_top() for ram_top init base on
SDRAM_MAX_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Added SDRAM_MAX_SIZE definition for RK3036:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
fixup: 3036 fix for sdram_common
According to rk3328 TRM:
0~0xff000000 is ddr space;
0xff000000~0xffffffff is device space.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
With the new dev_read functions available, we can convert the rockchip
architecture-specific drivers and common drivers used by these devices
over to the dev_read family of calls.
This covers the DRAM controller initialisation for the RK3188, RK3288
and RK3399... all of these read some of the tuning/setup/timing
parameters from the device-tree.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The size of the secure image does not include the size of the
header, subtract this out before we move the image or we grab
extra data after the image.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
gpio2 is used to detect lcd based on which pin mux is done in SPL.
gpio7 is used to enable vtt regulator. Enable these two gpio nodes
in SPL.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Enable spl_early_init() so that spl can use
DT very early during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
ROM stores the boot params information in a known location
and passes it to SPL. This information needs to be copied
very early during boot or else there is a chance of getting
corrupted by SPL. So move this boot device detection very early
during boot.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This port adds support for:
1) Serial
2) eMMC
3) USB
It has been tested with ARM TRUSTED FIRMWARE running u-boot as the
BL33 executable [see board's README]
eMMC has been tested for reading and booting the loader and linux
kernels as well as saving the u-boot environment.
USB has been tested with ASIX networking adapter and SanDisk 7.4GB
drive.
PSCI has been tested via the reset call (PSCI executes from DDR)
The firwmare upgrade process has been tested via TFTP and USB FAT
filesystem containing the fastboot.bin image in one of the partitions.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable netcp by default like all other peripherals in the dtsi file.
Enable the peripheral explicitly in the board specific dts file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Upstream Linux has the unit address being added to the various 66AK2Gx
boards dts. Therefore, update the dts to mimic this change.
Also remove memory node from the base K2G dtsi file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Future boards will need to configure DDR3 registers in a slightly
different manner. Support this by defining additional variables and
defines that will be utilized later.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
u-boot.bin is a copy of:
u-boot-fit-dtb.bin if CONFIG_FIT_EMBED is enabled,
u-boot-dtb.bin if CONFIG_OF_SEPARATE is enabled,
u-boot-nodtb.bin if DT is not enabled.
So, use u-boot.bin to to generate keystone images instead of
u-boot-dtb.bin
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier to
keep device tree files synced between U-boot and Linux.
For now only add nodes to allow i2c drivers to be probed early during
the boot process.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1 ("ARM: keystone: Enable DM_I2C by default")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
For processors whose core runs at twice the bus frequency,
the fallback frequency calculation in Linux provides a wrong
result. Therefore, U-boot needs to pass the correct value.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
immap.c used to be common to several CPUs. It is now
only linked to the 8xx, so this patch moves it into
arch/powerpc/cpu/mpc8xx/
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
CS Systemes d'Information (CSSI) manufactures 8xx boards for
critical communication systems. Those boards have been
running U-Boot since 2010 and will have to be maintained
until at least 2027.
commit 5b8e76c35e
("powerpc, 8xx: remove support for 8xx") orphaned those boards
by removing support for the mpc8xx CPU.
This commit partially restores support for the 8xx, with the
following limitations:
- Restores support for MPC866 and MPC885 only
- Does not restore IDE, PCMCIA, I2C, USB
- Does not restore examples
- Does not restore POST
- Does not restore Ethernet on SCC
- Does not restore console on SCC
- Does not restore bedbug and kgdb support
As the 866 and 885 do not support the following features,
they are not restored either:
- VIDEO / LCD
- RTC clock
The CPM uCODE patch is not restored either, because:
- 866 and 885 already have support for I2C and SPI relocation
without a uCODE patch
- relocation of SMC, I2C or SPI is only needed for using SCCs
for Ethernet or QMC
The dynamic setup/calculation of clocks is removed, we
expect the target being use with the clock and PLPRCR register
defined in the configuration.
All the clock settings for 8xx prior to 866 is removed as
well as we now only support 866 and 885.
This code is mature and addresses mature boards. Therefore
all code enclosed in '#if 0/#endif' and '#if XX_DEBUG/#endif'
is unneeded.
The following files are not restored by this patch:
- arch/powerpc/cpu/mpc8xx/bedbug_860.c
- arch/powerpc/cpu/mpc8xx/fec.h
- arch/powerpc/cpu/mpc8xx/kgdb.S
- arch/powerpc/cpu/mpc8xx/plprcr_write.S
- arch/powerpc/cpu/mpc8xx/scc.c
- arch/powerpc/cpu/mpc8xx/upatch.c
- arch/powerpc/cpu/mpc8xx/video.c
- arch/powerpc/include/asm/status_led.h
- arch/powerpc/lib/ide.c
- arch/powerpc/lib/ide.h
- doc/README.MPC866
- drivers/pcmcia/mpc8xx_pcmcia.c
- drivers/rtc/mpc8xx.c
- drivers/usb/gadget/mpc8xx_udc.c
- drivers/video/mpc8xx_lcd.c
- examples/standalone/test_burst.c
- examples/standalone/test_burst.h
- examples/standalone/test_burst_lib.S
- examples/standalone/timer.c
- include/mpc823_lcd.h
- include/usb/mpc8xx_udc.h
- post/cpu/mpc8xx/Makefile
- post/cpu/mpc8xx/cache.c
- post/cpu/mpc8xx/cache_8xx.S
- post/cpu/mpc8xx/ether.c
- post/cpu/mpc8xx/spr.c
- post/cpu/mpc8xx/uart.c
- post/cpu/mpc8xx/usb.c
- post/cpu/mpc8xx/watchdog.c
Some of the restored files are not located in a proper location.
In order to keep traceability of the changes, they will be
moved to their correct location and moved to Kconfig in a
followup patch.
This patch also declares CSSI as point of contact for the update
of the 8xx platform, as those boards are the only ones still
being maintained on the 8xx area. A later patch will add
those boards to the tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The current code gives a warning:
arch/arm/mach-stm32/stm32f7/soc.c: In function 'arch_cpu_init':
arch/arm/mach-stm32/stm32f7/soc.c:38:2: error: 'for' loop initial
declarations are only allowed in C99 or C11 mode
for (int i = 0; i < ARRAY_SIZE(stm32_region_config); i++)
^
arch/arm/mach-stm32/stm32f7/soc.c:38:2: note: use option -std=c99,
-std=gnu99, -std=c11 or -std=gnu11 to compile your code
Fix it by moving the declaration to the top of the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-cc trini
This actually works on snapdragon.. not sure why we weren't using it.
Fixes reboot/poweroff when using UEFI.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
The author of the commit discovered later on that this was already being
done in cleanup_before_linux() on arch/arm/cpu/armv7m/cpu.c.
This reverts commit 8f079cccb3.
Signed-off-by: Tom Rini <trini@konsulko.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to use the same memory layout and size for a couple of
boards and thus we just hardcoding IOC aperture start and size.
Now when we're getting more boards with more memory on board we
need to have an ability to set IOC so it matches real DDR layout
and size.
Even though it is not really a must but for simplicity we assume
IOC covers all the DDR we have, that gives us a chance to not
bother where DMA buffers are allocated - any part of DDR is OK.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARCompact cores are not supposed to be used in SMP designs
(this doesn't stop people from creation of heterogeneous chips,
for an example keep reading) so there's no point in
checking ARCNUM and halting somebody if we build for ARC700.
Moreover on AXS101 board we have ARC770 in the ASIC together with
other ARC cores and ARC770 happens to be the last node in JTAG chain
with ARCNUM = 4. And existing check halts the one and only core we
want keep running.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The origin SPL_USE_ARCH_MEMSET/MEMCPY use same prompt message
as USE_ARCH_MEMSET/MEMCPY, which makes it's hard to distinguish
them in menuconfig interface. This patch gives them different
prompt messages for spl and none-spl config.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix warnings reported by sparse:
- ... was not declared. Should it be static?"
- cast to restricted __be32
While fixing those, the type conflict of cci500_init() was found.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It has been observed that between PG1.0 and PG2.0/2.1 depending on
which device we boot from, we may see a different value here than is
documented in the TRM. Update the values for NAND and MMC1 based on
real life usage on each revision.
Signed-off-by: Tom Rini <trini@konsulko.com>
On ARCH_SUNXI we've been selecting these targets for a long time if
SUPPORT_SPL is set. However, Lichee Pi Zero is the first platform we've
added that does support SPL but does not build SPL and has exposed a
latent bug. Both of these symbols depend on SPL not SUPPORT_SPL, so we
need to update our select here otherwise we get a Kconfig warning.
Fixes: f02abb0608 ("sunxi: add support for Lichee Pi Zero")
Signed-off-by: Tom Rini <trini@konsulko.com>
The topic-miamilite SoM contains a Zynq xc7z010 SoC, 1GB DDR3L RAM,
64MB dual-parallel QSPI NOR flash and clock sources.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If PMUFW version is not v0.3 then panic.
ZynqMP switch to CCF based clock driver which requires
PMUFW to be present at certain version.
This patch ensure that you use correct and tested PMUFW
binary.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define routines of mmio write and read functionalities
for zynqmp platform.
Also do not call SMC from SPL because SPL is running before ATF in EL3
that's why SMCs can't be called because there is nothing to call.
zynqmp_mmio*() are doing direct read/write accesses and this patch does
the same. PMUFW is up and running at this time and there is a way to talk
to pmufw via IPI but there is no reason to implement IPI stuff in SPL if
we need just simple read for getting clock driver to work.
Also make invoke_smc as global so that it can be reused in
multile places where ever possible.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add Kconfig option for ddr init as this might be required
in cases like ddr less systems where we want to skip ddrc
init and this option is useful for it.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Silicon v1 didn't support SD boot mode with level shifter.
Because system can't boot any error message is not shown
that's why comment is just a record if someone tries to debug it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The boot_device argument to spl_boot_mode was massively added without
actually modifying the existing functions.
This commit actually makes use of the handed value, which is the same.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
When enabling both SDHCI controllers, spl_mmc.c would actually choose
device sdhci0 even if booted from sdhci1 (boot_device). This is because
spl_mmc_get_device_index(boot_device) expects BOOT_DEVICE_MMC2[_2] in
order to return index 1 instead of 0.
The #if defined(...) statement is copied from board/xilinx/zynqmp/zynqmp.c
So the key to properly enabling both controllers as boot sources is
defining both CONFIG_ZYNQ_SDHCI0 and CONFIG_ZYNQ_SDHCI1 in your board's
include/configs/*.h.
Signed-off-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Adding more targets to repository requires some additional
changes not simply just adding config file, defconfig and dts.
This patch makes this process easier by building only
particular DTB which is selected via defconfig
that Makefile doesn't need to contain all dts files in the repository.
Reported-by: Nathan Rossi <nathan@nathanrossi.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There was for long time no activity in the mpx5xxx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in mpc5xxx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Secure boot targets that can be loaded from an SD card FAT partition
need to be called "MLO" on the filesystem, make a copy with this name
to clarify the correct image for SD card booting.
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
NanoPi NEO2 is designed and developed by FriendlyElec
using the Allwinner 64-bit H5 SOC.
NanoPi Neo2 key features
- Allwinner H5, Quad-core 64-bit Cortex-A53
- 512MB DDR3 RAM
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC MicroUSB power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
It turns out this change was not intended to be merged and as such,
revert it.
This reverts commit cdde7de036.
Reported-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Orangepi Win/WinPlus is an open-source single-board computer
using the Allwinner A64 SOC.
A64 Orangepi Win/WinPlus has
- A64 Quad-core Cortex-A53 64bit
- 1GB(Win)/2GB(Win Plus) DDR3 SDRAM
- Debug TTL UART
- Four USB 2.0
- HDMI
- LCD
- Audio and MIC
- Wifi + BT
- IR receiver
- 5V DC power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Orangepi Zero Plus 2 is an open-source single-board computer
using the Allwinner h5 SOC.
H5 Orangepi Zero Plus 2 has
- Quad-core Cortex-A53
- 512MB DDR3
- micrSD slot and 8GB eMMC
- Debug TTL UART
- HDMI
- Wifi + BT
- OTG+power supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
With Davinci I2C switching to device model, K2HK requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1 ("ARM: keystone: Enable DM_I2C by default")
Reported-by: Yan Liu <yan-liu@ti.com>
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Create exception stack in IRAM if available to facilitate debugging of
pre-relocation code by catching exceptions rather than stopping dead.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Adjust the program counter register to point to the failing
instruction depending on the exeption type.
This makes it easier to localize the offending instruction leading to
a fatal exception.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
The cp_delay() function was introduced because of a missing 'volatile'
attribute to the 'asm' statement in get_cr() which led to the 'mrc'
instruction in get_cr() being optimised out eventually.
This has been fixed in commit 53fd4b8c22 ("arm: mmu: Add missing volatile for reading SCTLR register")
but the bogus cp_delay() function which was introduced as a workaround
for the malfunctioning get_cr() was never removed.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
stm32x7.c driver is dedicated for STM32F7.
In kernel, "st,stm32-usart" and "st,stm32-uart" compatible
strings are dedicated for STM32F4.
To keep U-boot and kernel aligned, replace the serial compatible
string from "st,stm32-usart", "st,stm32-uart" to
"st,stm32f7-usart", "st,stm32f7-uart" specific for STM32F7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Christophe KERELLO <christophe.kerello@st.com>
Reviewed-by: Patrick DELAUNAY <patrick.delaunay@st.com>
Acked-by: Vikas MANOCHA <vikas.manocha@st.com>
There was for long time no activity in the 5xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 5xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8260 area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8260,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
There was for long time no activity in the 8xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 8xx,
so remove it (with a heavy heart, knowing that I remove
here the root of U-Boot).
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch reuses new option, which allows us to expose variables
from environment to "fastboot getvar" command. Those variables must be
of "fastboot.%s" format.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Using u-boot-2017.05 on i.MX6UL we ran into following problem:
Initially U-Boot could be started normally.
If we added one random command in configuration, the newly generated
image hung at startup (last output was DRAM: 256 MiB).
We tracked this down to a data abort within relocation (relocated_code).
relocated_code in arch/arm/lib/relocate.S copies 8 bytes per loop
iteration until the source pointer is equal to __image_copy_end.
In a good case __image_copy_end was aligned to 8 bytes, so the loop
stopped as suggested, but in an errornous case __image_copy_end was
not aligned to 8 bytes, so the loop ran out of bounds and caused a
data abort exception.
This patches solves the issue by aligning __image_copy_end to 8 byte
using the linker script related to arm.
I don't know if it's the correct way to solve this, so some review would
be very appreciated.
Currently we set the entry address in the psci_cpu_on function.
However R40 has a different register for this. This resulted in
an #ifdef / #else block in psci_cpu_on, which we avoided having
in the first place.
Move this part into a separate function, defined differently for
the R40 as opposed to the other single cluster platforms.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Disable D-Cache is required when booting nommu Linux kernel.
(please see Linux kernel source "arch/arm/kernel/head-nommu.S")
U-Boot is enabled D-cache and I-Cache at startup.
However, it does not disable D-Cache before
booting nommu Linux kernel.
Therefore, I call dcache_disable()
when the CPU is ARMv7M to fix this problem.
Signed-off-by: Toshifumi NISHINAGA <tnishinaga.dev@gmail.com>
Refactor OMAP3/4/5 code so that we have only one get_device_type()
function for all platforms.
Details:
- Add ctrl variable for AM33xx and OMAP3 platforms (like it's done for
OMAP4/5), so we can obtain status register in common way
- For now ctrl structure for AM33xx/OMAP3 contains only status register
address
- Run hw_data_init() in order to assign ctrl to proper structure
- Remove DEVICE_MASK and DEVICE_GP definitions as they are not used
(DEVICE_TYPE_MASK and GP_DEVICE are used instead)
- Guard structs in omap_common.h with #ifdefs, because otherwise
including omap_common.h on non-omap4/5 board files breaks compilation
Buildman script was run for all OMAP boards. Result output:
arm: (for 38/616 boards)
all +352.5
bss -1.4
data +3.5
rodata +300.0
spl/u-boot-spl:all +284.7
spl/u-boot-spl:data +2.2
spl/u-boot-spl:rodata +252.0
spl/u-boot-spl:text +30.5
text +50.4
(no errors to report)
Tested on AM57x EVM and BeagleBoard xM.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
[trini: Rework the guards as to not break TI81xx]
Signed-off-by: Tom Rini <trini@konsulko.com>
Almost all users of CONFIG_AM33XX/AM43XX have been migrated. Finish
moving the last few over to Kconfig, and put all of the boards under the
appropriate Kconfig chocie now. This board choice is non-optional, so
remove that keyword on am33xx.
Signed-off-by: Tom Rini <trini@konsulko.com>
If U-Boot is chain-loaded from a previous boot loader we must set up the
clocks the way U-Boot wants them. Add code for this. It will do nothing if
SPL has already done the job.
Signed-off-by: Simon Glass <sjg@chromium.org>
Shifted masks are the standard approach with rockchip since it allows
use of the mask without shifting it each time. Update the definitions and
the driver to match.
Signed-off-by: Simon Glass <sjg@chromium.org>
The clock fix-up for tegra is still present in the code. It causes a
divide-by-zero bug after relocation when chain-loading U-Boot from
coreboot. Fix this by adding a check.
Signed-off-by: Simon Glass <sjg@chromium.org>
Fixes: 7468676 (ARM: tegra: fix clock_get_periph_rate() for UART clocks)
At present the interrupt does not work and the SPI bus runs much less
quickly than it should. Add settings to fix this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present early clock init happens in SPL. If SPL did not run (because
for example U-Boot is chain-loaded from another boot loader) then the
clocks are not set as U-Boot expects.
Add a function to detect this and call the early clock init in U-Boot
proper.
Signed-off-by: Simon Glass <sjg@chromium.org>
If CONFIG_ARMV7_LPAE is not defined we should make sure that the feature
is disabled. This can happen if U-Boot is chain-loaded from another boot
loader which does enable LPAE.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present if CONFIG_ARMV7_LPAE is defined then mmu_setup() will use
instructions which are invalid on ARMv4T. This happens on Tegra since it
has an ARMv4T boot CPU. Add a check for the architecture version to allow
the code to be built. It will not actually be executed by the boot CPU,
but needs to compile.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option allows skipping the call to lowlevel() while still performing
CP15 init. Support this on ARM720T so it can be used with Tegra.
Signed-off-by: Simon Glass <sjg@chromium.org>
With xip booting configuration, we don't need to copy the next image
(U-Boot or linux xipimage) from flash to sdram area.
Flash memory organization is like this:
spl-U-Boot: u-boot-spl.bin : 0x0800_0000
U-Boot : u-boot-dtb.bin : 0x0800_8000
linux : xipImage : 0x0800_8000
It is also possible to have U-Boot binary & linux binaries configured at
different addresses of flash memory like U-Boot at 0x0800_8000 & linux
xipImage at 0x0800_4000. But in any case, spl-U-Boot needs to be compiled for
U-Boot as next binary with SPL_OS_BOOT option disabled.
By default, spl is configured to boot linux xipImage.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Enable support for XIP (execute in place) of U-Boot or kernel image. There is
no need to copy image from flash to ram if flash supports execute in place.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Alexandru Gagniuc <alex.g@adaptrum.com>
This commit supports booting from stm32 internal nor flash. spl U-Boot
initializes the sdram memory, copies next image (e.g. standard U-Boot)
to sdram & then jumps to entry point.
Here are the flash memory addresses for U-Boot-spl & standard U-Boot:
- spl U-Boot : 0x0800_0000
- standard U-Boot : 0x0800_8000
To compile u-boot without spl: Remove SUPPORT_SPL configuration
(arch/arm/mach-stm32/Kconfig)
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Rework Kconfig logic a bit]
Signed-off-by: Tom Rini <trini@konsulko.com>
Extend DE2 driver with support for TVE driver, which will be added in
next commit. TVE unit expects data to be in YUV format, so CSC support
is also added here.
Note that HDMI driver has higher priority, so TV out is not probed if
HDMI monitor is detected.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds TVE base address for Allwinner H3 and H5 SoCs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
In os_dirent_get_typename() we are checking that type falls within the
known values of the enum os_dirent_t. With clang-3.8 testing this value
as being >= 0 results in a warning as it will always be true. This
assumes of course that we are only given valid data. Given that we want
to sanity check the input, we change this to check that it falls within
the range of the first to the last entry in the given enum.
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As we added LPDDR3 support in the former patch, we need a set of timing
info to really enable it.
Add the timing info used by stock boot0.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some A64 boards (SoPine and Pinebook production batch) use LPDDR3 DRAM
chips.
Add support for LPDDR3 DRAM in the DesignWare-like DRAM controller code.
Real LPDDR3 chips' support is not added yet in this commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
As we have already support for the DesignWare DRAM controller and the
integrated DDR2 chip of V3s, let's enable the SPL support for V3s.
This patch also contains the default DRAM configuration for V3s.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s features a DRAM controller like the on in H3, but with a
DDR2 DRAM.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner V3s SoC features a co-packaged DDR2 DRAM chip, which needs its
timing param.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare-like DRAM code used to set the controller defaultly to
single rank mode, which makes it not able to detect the second rank.
Set the default value to dual rank, thus the rank detection code can
work and finally the rank setting will be the correct value.
Currently we know little about the dual-rank on R40, and the usage
of A15 address line seems to be breaking dual-rank support. The only R40
board currently available (Sinovoip Banana Pi M2 Ultra) uses A15 rather
than dual-rank, thus we cannot do research for it. So dual rank detection
is temporarily disabled on R40.
This change is tested on a Orange Pi One (H3, single rank), a Pine64+
2GiB version (A64, single rank) , a Pinebook early prototype with DDR3
(A64, dual rank) and a SoPine with some LPDDR3 patch (A64, dual CS pins
on one chip).
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
DRAM chip varies, and one code cannot satisfy all DRAMs.
Add options to select a timing set.
Currently only DDR3-1333 (the original set) is added into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some DDR2 DRAM have only four banks, not eight.
Add code to detect this situation.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Some Allwinner SoCs features a DesignWare-like controller with only 16
bit bus width.
Add support for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
The DesignWare DRAM controller used by H3 and newer SoCs use a bit to
identify whether the DRAM is half-width.
As H3 itself come with 32-bit DRAM, the two modes of the bit used to be
named "MCTL_CR_32BIT" and "MCTL_CR_16BIT", but for SoCs with 16-bit DRAM
they're really 8-bit and 16-bit.
Rename the bit's macro, and also rename the variable name in
dram_sun8i_h3.c.
This commit do not add 16-bit DRAM controller support, but the support
will be introduced in next commit.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Allwinner SoCs after H3 (e.g. A64, H5, R40, V3s) uses a H3-like
DesignWare DRAM controller, which do not have official free DRAM
initialization code, but can use modified dram_sun8i_h3.c.
Add a invisible option for easier DRAM initialization code reuse.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.
NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
This commit enables the RK3399 HDMI TX, which is very similar to the
one found on the RK3288. As requested by Simon, this splits the HDMI
driver into a SOC-specific portion (rk3399_hdmi.c, rk3288_hdmi.c) and
a common portion (rk_hdmi.c).
Note that the I2C communication for reading the EDID works well with
the default settings, but does not with the alternate settings used on
the RK3288... this configuration aspect is reflected by the driverdata
for the RK3399 driver.
Having some sort of DTS-based configuration for the regulator
dependencies would be nice for the future, but for now we simply use
lists of regulator names (also via driverdata) that we probe.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds a driver for the RK3399 VOPs capable and all the
necessary plumbing to feed the HDMI encoder. For the VOP-big, this
correctly tracks the ability to feed 10bit RGB data to the encoder.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
To prepare for adding the RK3399 VOP driver (which shares most of its
registers and config logic with the RK3228 VOP), this change refactors
the driver and splits the RK3288-specific driver off.
The changes in detail are:
- introduces a data-structure for chip-specific drivers to register
features/callbacks with the common driver: at this time, this is
limited to a callback for setting the pin polarities (between the
VOP and the encoder modules) and a flag to signal 10bit RGB
capability
- refactors the probing of regulators into a helper function that
can take a list of regulator names to probe and autoset
- moves the priv data-structure into a (common) header file to be
used by the chip-specific drivers to provide base addresses to
the common driver
- uses a callback into the chip-specific driver to set pin polarities
(replacing the direct register accesses previously used)
- splits enabling the output (towards an encoder) into a separate
help function withint the common driver
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RK3288_TXCLK_DLY_ENA_GMAC_ENABLE, in GRF_SOC_CON3, is supposed to be bit
0xe and not 0xf. Otherwise, it is RGMII RX clock delayline enable and
introduces random delays and data lose.
This commit fixes the issue by replacing RK3288_TXCLK_DLY_ENA_GMAC_ENABLE
with the right shift.
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1866 timing via its own DTS and wires it up. This
(currently) is not the default timing for the RK3399-Q7 and should be
selected explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
This adds the DDR3-1333 timing via its own DTS and wires it up. This
is not the default timing for the RK3399-Q7 and should be selected
explicitly via the config (CONFIG_DEFAULT_DEVICE_TREE).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
To better support different RAM timings (DDR3-1333 and DDR3-1866 are
assembly options for the RK3399-Q7), this refactors the DTS support
and renames the default DTS variant from rk3399-puma to
rk3399-puma-ddr1600:
- changes the rk3399-puma DTS into a board-specific DTSI by removing
the inclusion of the DRAM timings
- adds a new rk3399-puma-ddr1600.dts, which includes the (new) common
board DTSI and the DDR3-1600 timing DTSI
- wires this up from arch/arm/dts/Makefile and configs/puma-rk3399_defconfig
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Linux DTS for the RK3399-Q7 has moved with the times... resync
against it to ensure a consistent configuration.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit enables HDMI output in the DTS by adding the necessary
nodes to vopl/vopb and by adding the HDMI node.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add basic support for rv1108 evb, whith this patch we
can boot into u-boot console.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
RV1108 is embedded with an ARM Cortex-A7 single core and a DSP core
from Rockchip. It is designed for varies application scenario such
as car DVR, sports DV, secure camera and UAV camera.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
defines the spl-payload to 256k (0x40000)
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
On the RK3399-Q7, the on-module USB3 hub is held in reset at boot-up
to save power and needs to be woken up using GPIO4A3.
Note that this is not a negated reset-signal (due to a level shifter
being needed for this signal anyway), but a negated enable-signal:
to enable, we need to output LOW (i.e. 0)... so we mark this as an
ACTIVE_LOW signal.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the validation done for DDR3-1866 (i.e. 933 MHz bus clock), we
can now add the timings (rk3399-sdram-ddr3-1866.dtsi) for boards built
with the DDR3-1866 option.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The RK3399 is capable of driving DDR3 at 933MHz (i.e. DDR3-1866),
if the PCB layout permits and appropriate memory timings are used.
This changes the sanity checks to allow a DTS to request DDR3-1866
operation.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Revise the loop watching for a timeout on obtaining a DRAM PHY lock to
clearly state a timeout in milliseconds and use get_timer (based on
the ARMv8 architected timer) to detect a timeout.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In rk3328, some function pin may have more than one choice, and muxed
with more than one IO, for example, the UART2 controller IO,
TX and RX, have 3 choice(setting in com_iomux):
- M0 which mux with GPIO1A0/GPIO1A1
- M1 which mux with GPIO2A0/GPIO2A1
- usb2phy which mux with USB2.0 DP/DM pin.
We should not decide which group to use in pinctrl driver,
for it may be different in different board, it should goes to board
file, and the pinctrl file should setting correct iomux depends on
the com_iomux value.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move GRF register bit definition into GRF header file, remove
'GRF_' prefix and add 'GPIOmXn_' as prefix for bit meaning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot prefer to use MASKs with SHIFT embeded, clean the Macro
definition in grf header file and pinctrl driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- hclk/pclk_div range should use '<=' instead of '<'
- use GPLL for pd_bus clock source
- pd_bus HCLK/PCLK clock rate should not bigger than ACLK
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Embeded the shift in mask MACRO definition in cru header file
and clock driver.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PX5 EVB is designed by Rockchip for automotive field
with integrated CVBS (TP2825) / MIPI DSI / CSI / LVDS
HDMI video input/output interface, audio codec ES8396,
WIFI / BT (on RTL8723BS), Gsensor BMA250E and light&proximity
sensor STK3410.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The GeekBox is a TV box from GeekBuying, based on an MXM3 module.
The module can be used with base boards such as the GeekBox Landingship.
This adds basic support to chain-load U-Boot from Rockchip's miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Sheep board is designed by Rockchip as a EVB for rk3368.
Currently it is able to boot a linux kernel and system
to console with the miniloader run as fist level loader.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The RK3368 is an octa-core Cortex-A53 SoC from Rockchip.
This adds basic support to chain-load U-Boot from Rockchip's
miniloader.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to support iomux setup for the most commonly
used peripherals on rk3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add driver to setup the various PLLs and peripheral
clocks on the RK3368.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some host like SD and eMMC may use DMA to transter data to SRAM,
set memory to non-secure to make sure the address can be accessed.
The security of SRAM in OS suppose to initialized in ATF bl31, and
the SPL is before the bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Simon Glass <sjg@chromium.org>
The branch instruction only has an 11-bit relative target address, which
is sometimes not enough.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Rather than change asm files that come from Linux, add the symbols
to Kconfig. Since one of the symbols is for thumb2 builds, make
CPU_V7M always select them.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Mark explicitly bss sections to not be loaded at
run time.
The similar patch was done in past by:
"Fix linker scripts: add NOLOAD atribute to .bss/.sbss sections"
(sha1: 64134f0112)
The problem is related to latest toolchain added to Xilinx
v2017.1 design tools where jtag loader is trying to access
ununitialized memory.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for calling poweroff in case of psci is wired.
Based on the same solution as is used for reset.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Move all logic in to fwcall.c as other ARMs implement poweroff
via PMIC]
Signed-off-by: Tom Rini <trini@konsulko.com>
The dtb blob section must always be present in the resulting image.
Either if OF_EMBEDED is used or if unit tests include dtb blobs.
Signed-off-by: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present we provide a default version of this function for use by
bootstage. However it uses the system timer and therefore likely requires
driver model. This makes it impossible to time driver-model init.
Drop the function and require boards to provide their own. Add a sandbox
version also. There is a default implememtation in lib/time.c for boards
which use CONFIG_SYS_TIMER_COUNTER.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Adjust the
board files a little so it is not needed, and drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should not have an arch-specific header file in common.h. Instead, use
the asm/hardware.h header to provide the required declarations, and drop
the common.h changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These declarations should not be in common. Remove those that are not
needed and move the others to an arch-specific location.
Signed-off-by: Simon Glass <sjg@chromium.org>