Add BSEC lock access (read / write) at 0xC0000000 offset of misc driver.
The write access only available for Trusted boot mode, based on new
SMC STM32_SMC_WRLOCK_OTP.
With the fuse command, the permanent lock status is accessed with
0x10000000 offset (0xC0000000 - 0x8000000 for OTP sense/program
divided by u32 size), for example:
Read lock status of fuse 57 (0x39)
STM32MP> fuse sense 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
Set permanent lock of fuse 57 (0x39)
STM32MP> fuse prog 0 0x10000039 1
Sensing bank 0:
Word 0x10000039: 00000000
WARNING: the OTP lock is updated only after reboot
WARING: Programming lock or fuses is an irreversible operation!
This may brick your system.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Remove the test offs < 0 , as offs is unsigned.
This patch solves the warnings when compiling with W=1
on stm32mp1 board:
In function ‘stm32mp_bsec_read’:
arch/arm/mach-stm32mp/bsec.c:368:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
368 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
In function ‘stm32mp_bsec_write’:
arch/arm/mach-stm32mp/bsec.c:405:11: warning:
comparison of unsigned expression < 0 is always false [-Wtype-limits]
405 | if (offs < 0 || (offs % 4) || (size % 4))
| ^
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
K3 J721E:
* OSPI boot support
* Support for loading remote cores in R5 SPL
* PMIC ESM Support
* Minor fixes for R5F and C7x remoteproc drivers
K3 AM654:
* Update AVS class 0 voltages.
* Add I2C nodes
DRA7xx/AM57xx:
* Fixed Android boot on AM57xx
AM33/AM43/Davinci:
* switch to driver model for the net and mdio driver for baltos
* Add DM/DTS support for omap video driver
* Enable fastboot on am335x-evm
As there is only one linker script to use in this case, rather than use
the BOARDDIR variable hard-code the path.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
As there is only one machine under mach-orion5x, having a Kconfig entry
for SPL_LDSCRIPT is not helpful, move this to the defconfig file.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Masahiro Yamada <masahiroy@kernel.org>
The A72 U-Boot code supports early load and boot of a number of
remote processors including the C66_0 and C66_1 DSPs. The current
code supports only loading into the DDR regions which were already
given the appropriate memory attributes. The C66 DSPs also have L1
and L2 internal memory regions that can behave as normal-memories.
Add a new entry to the J721E MMU table covering these regions with
the appropriate memory attributes to allow the A72 U-Boot code to
support loading directly into these memory regions.
Signed-off-by: Suman Anna <s-anna@ti.com>
Add a separate function for printing sysfw version so that it can be
called independently of k3_sysfw_loader.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The binman-option BINMAN_FDT is introduced by this commit:
commit 3c10dc95bd ("binman: Add a library to access binman entries")
BINMAN_FDT being selected when BINMAN=y that resulting in mt7623
and mt7622 are unable to boot. The root cause of this issue is commit:
commit cbd2fba1ec ("arm: MediaTek: add basic support for MT7629 boards")
select BINMAN=y in all mediatek SoCs, and others mediatek SoCs not
expect to use BINMAN_FDT.
This patch remove BINMAN=y option when ARCH_MEDIATEK=y and
move this to the specify SoCs part config.
Signed-off-by: Sam Shih <sam.shih@mediatek.com>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Instead of resetting the ethernet phy through functions in imx8mq_evk.c, let the
driver reset the phy via dts description adding a reset duration of 10 ms
following atheros 8031's datasheet recommendation.
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
The FEC in the i.MX8MM doesn't support this feature. So don't pretend one
can use it.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Let pinctrl configuration for eMMC node (usdhc1) also be
accessible in SPL.
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
The current implementation in arch/arm/mach-imx/cpu.c uses non-DM
code to retrieve the core clock frequency. As the root clock is not
listed we currently get:
CPU: Freescale i.MX8MMQ rev1.0 at 0 MHz
Fix this by adding the missing entry, which results in:
CPU: Freescale i.MX8MMQ rev1.0 at 1200 MHz
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Before DM_VIDEO conversion this board used 24bpp
display configuration, so use it again.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Update the dummy clock names to use unique identifiers. Otherwise the
previous node just gets overwitten by the next one with the same name.
This fixes eMMC boot not working on J721e-evm.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
System firmware does not guarantee that clocks going out of the device
will be stable during power management configuration. There are some
DCRC errors when SPL tries to get the next stage during eMMC boot after
sysfw pm configuration.
Therefore add a config_pm_pre_callback() to switch off the eMMC clock
before power management and restart it after it is done.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
The call to spl_mmc_get_uboot_raw_sector() completely ignores and
overwrites the raw_sect value passed from the caller of spl_mmc_load().
Fix this by passing raw_sect to the function and returning the same
value in the default case.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
With the latest RIOT, there is a different otap delay value for each
speed mode. Add a new binding with every supported speed mode. Also
disable a given speed mode in the host caps if its corresponding
otap-del-sel is not present.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Add the "u-boot,dm-pre-reloc" property to the "ti,tilcdc,panel"
compatible node. In this way the video-uclass module can allocate the
amount of memory needed to be assigned to the frame buffer.
For boards that support Linux the property is added to the *-u-boot.dtsi
file since it is a u-boot specific dt flag.
Ran building tests with CONFIG_AM335X_LCD enabled and disabled for the
following configurations:
- brxre1_defconfig --> success
- am335x_guardian_defconfig --> success
- am335x_evm_defconfig --> success
- da850evm_defconfig --> failure with CONFIG_AM335X_LCD enabled
Enabling CONFIG_AM335X_LCD in da850evm_defconfig causes building errors
even without applying the patch. The driver has never been enabled on the
da850 and must be adapted for this platform.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Felix Brack <fb@ltec.ch>
Update the driver to support the device tree and the driver model.
Timings and panel parameters are now loaded from the device tree.
The DM code replaces the am335x_lcdpanel structure with
tilcdc_panel_info taken from the linux kernel, as well the management
of additional parameters not covered in the legacy code. In addition,
the am335x_lcdpanel structure contains parameters and operations that
were probably a requirement of the board for which this driver was
developed and which, however, were not developed in the linux kernel.
All this led to rewrite th DM controller initialization code, except
for the pixel clock setting that is executed in a function created in a
previous patch with code taken from the legacy am335xfb_init.
The patch has been tested on a custom board with u-boot 2018.11-rc2 and
the following device-tree configuration:
panel {
compatible = "ti,tilcdc,panel";
pinctrl-names = "default";
pinctrl-0 = <&lcd_enable_pins>;
enable-gpios = <&gpio0 31 0>;
backlight = <&backlight>;
status = "okay";
u-boot,dm-pre-reloc;
panel-info {
ac-bias = <255>;
ac-bias-intrpt = <0>;
dma-burst-sz = <16>;
bpp = <16>;
fdd = <0x80>;
sync-edge = <0>;
sync-ctrl = <1>;
raster-order = <0>;
fifo-th = <0>;
};
display-timings {
native-mode = <&timing0>;
timing0: 800x480 {
hactive = <800>;
vactive = <480>;
hback-porch = <46>;
hfront-porch = <210>;
hsync-len = <20>;
vback-porch = <23>;
vfront-porch = <22>;
vsync-len = <10>;
clock-frequency = <33000000>;
hsync-active = <0>;
vsync-active = <0>;
};
};
};
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Tested-by: Dario Binacchi <dariobin@libero.it>
The ESM handling on J7 processor board requires routing the
MCU_SAFETY_ERROR signal to the PMIC on the board for critical safety
error handling. The PMIC itself should then reset the board based on
receiving it. Enable the support for the board by adding the esm
node in place.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Main domain ESM support is needed to configure main domain watchdogs
to generate ESM pin events by default. On J7 processor board these
propagate to the PMIC to generate a reset when watchdog expires.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Add fs_loader node which will be needed for loading firmwares
from the boot media/filesystem.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
MCU Domain rf50 is currently shutting down after loading the ATF.
Load elf firmware and jump to firmware post loading ATF.
ROM doesn't enable ATCM memory, so make sure that firmware that
is being loaded doesn't use ATCM memory or override SPL.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add MAIN domain R5FSS0 remoteproc support from spl. This enables
loading the elf firmware in SPL and starting the remotecore.
In order to start the core, there should be a file with path
"/lib/firmware/j7-main-r5f0_0-fw" under filesystem
of respective boot mode.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
[Guard start_non_linux_remote_cores under CONFIG_FS_LOADER]
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Move the generic elf loading/validating functions to lib/
so that they can be re-used and accessed by code existing
outside cmd.
While at it remove the duplicate static version of load_elf_image_phdr
under arch/arm/mach-imx/imx_bootaux.c.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Since ROM configures OSPI controller to be in memory mapped mode in OSPI
boot, R5 SPL can directly pass the memory mapped pointer to ROM. With
this ROM can directly pull the SYSFW image from OSPI.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Populate address mapping entries in A53 MMU for 4 GB of MMIO space
reserved for providing MMIO access to multiple flash devices through
OSPI/HBMC IPs within FSS.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
The compatible string "i2c-eeprom" is U-Boot own compatible, which
has never been approved by the DT community. "u-boot,i2c-offset-len"
is also a U-Boot own hack.
Linux adds "atmel,*" as generic compatibles, and U-Boot also followed
it by commit d7e28918aa ("i2c_eeprom: Add reading support").
The U-Boot own hack is no longer needed. Just sync with Linux.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Import the nodename changes I made in Linux for avoiding dt-schama
warnings. This follows the $nodename patterns in the dt-schema.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address 0x43f00000 is no longer true for the future SoC.
Extract the base address from the device tree.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This workaround was previously needed for LD4, Pro4, sLD8, Pro5
SoCs. The boot ROM does not touch this register for PXs2/LD6b or
later.
Now that the reset signal of the Denali NAND controller is always
asserted in board_init() then deasserted in the driver, the
WRITE_PROTECT register gets back to the default value, which means
the write protect is deasserted.
This workaround can go away entirely.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The comment /* deassert reset */ is wrong. It asserts the reset.
It no longer needs to stay in SPL. The NAND controller reset is
handled in the driver. So, this assert can be moved to the
board_init() of U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add handy macros:
- sdscript: source boot.scr in the file system of the SD media
- sdboot : boot the kernel using the images in the file system
of the SD media
- sdscript: update the boot firmware in the SD media
(in raw block sectors)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Macro SZ_64K is undeclared. Include sizes.h to fix the compilation
error.
Signed-off-by: Wasim Khan <wasim.khan@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
