The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass <sjg@chromium.org>
in thumb mode compiler says for example for arch/arm/lib/cache-cp15.c
when enabling CONFIG_SYS_THUMB_BUILD:
{standard input}: Assembler messages:
{standard input}:373: Error: selected processor does not support Thumb mode `mrc p15,0,r4,c1,c0,0'
{standard input}:416: Error: selected processor does not support Thumb mode `mcr p15,0,r3,c2,c0,0'
so, if caches are disabled, do not use this command on arm926ejs.
used on at91 in SPL, to reduce size of SPL.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the new Barco platinum platform. It currently
includes those two boards:
platinum-titanium
-----------------
This is the same board as the titanium that is already supported in
mainline U-Boot. But its now moved to this new platform to support
multiple "flavors" of imx6 boards in one directory. Its also moved
to support SPL booting. And with this we use the run-time DDR
configuration of this SPL support. The board is equipped with the
Micron MT41J128M16JT-125 DDR chips. We now can remove the DDR
related registers tuples from the imximage.cfg file. As all this
is done in the SPL at run-time.
platinum-picon
--------------
This board is new and based on the MX6DL with 1GiB DDR using the
Micron MT41K256M16HA DDR3 chips. Its also equipped with 2 NAND
chips (each 512MiB).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Pieter Ronsijn <pieter.ronsijn@barco.com>
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only change is that we need our own
implementation of board_init_f() which sets up DRAM before the BSS (which
is in DRAM) is cleared.
The s_init() code runs once for SPL and again for U-Boot proper. We
shouldn't need to init the clock/timer/gpio/i2c init twice, so just have it
in SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
We need to get rid of this SPL-specific setting of the global_data pointer.
It is already set up in start.S immediately before board_init_f() is called,
and there may be information there that is needed (e.g. pre-reloc malloc
info).
Signed-off-by: Simon Glass <sjg@chromium.org>
Prior to this change we set the gd pointer early so that we can store
data in it. This becomes problematic for DM changes as well as being
odd in general. Re-work the code paths so that we don't need to set the
gd pointer so early and instead can rely upon the normal setting of it.
In order to do this we do need to move certain calls from s_init into
spl_board_init(), mainly preloader_console_init and
save_omap_boot_params.
Tested on: Beaglebone Black, AM43xx GP EVM, Beagleboard, Beagleboard xM,
OMAP5 uEVM, DRA7xx EVM
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some Freescale SoCs like T1020 and T1040 have an integrated
L2 Switch. The L2 Switch ports may be connected to Ethernet PHYs
over SGMII and QSGMII.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The number of supported serdes protocols on Freescale SoCs
has increased over time. Until now, an u64 variable have been
initialized on boot with the configured protocols. However,
since this number has increased (enum srds_prtcl has more
than 64 values), 64 bits are no longer sufficient to hold track
of all the configured protocols.
This patch replaces the u64 map values with static arrays.
To keep track of the number of serdes protocols, the
SERDES_PRCTL_COUNT vale has been added at the end of
enum srds_prtcl. This value must always be the last one.
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the boards that support deep sleep feature are converted
to deep sleep generic board interface. The old interface which
support non-generic board is not used anymore. So clean it up.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
CONFIG_SYS_PBI_FLASH_BASE is defined for Secure Boot on C29X
Signed-off-by: Aneesh Bansal <aneesh.bansal@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For B4 the LIODN register for PCIe is in PCIe address space and not in
GUTs
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. As a result, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h>.
The right fix would be to split the lib/fdtdec.c to remove
dependency on GPIO.
This commit adds a dummy <asm/arch/gpio.h> to support OF_CONTROL
for mpc85xx platform. A file mpc85xx_gpio.h exists in
arch/powerpc/include/asm. The defintions in that file conflict
with the ones in asm-generic/gpio.h. Hence a dummy header file
has been added. This will be removed after FDT-GPIO stuff is
fixed correctly.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
All the 74xx_7xx boards are still non-generic boards:
P3G4, ZUMA, ppmc7xx, ELPPC, mpc7448hpc2
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Now TQM8xx is the only remaining board family of mpc8xx.
It uses its own linker script, board/tqc/tqm8xx/u-boot.lds.
arch/powerpc/cpu/mpc8xx/u-boot.lds is not used by any boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Since commit 843125daeb (ppc4xx: remove HH405 board), CONFIG_HH405
is not defined.
Since commit d526330479 (ppc4xx: remove PMC405), CONFIG_PMC405
is not defined.
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
As a preparation to ARCv2 port submission we rename "arc700" folder to
"arcv1" which stands for ARCv1 ISA also known as ARCompact.
This will allow us to add more flavours of binary-compatible ARCv1 CPUs
like ARC600 if needed later on and all required ARCv2 CPUs (which are
binary incompatible with ARCv1) in "arcv2" folder in subsequent commits.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Both ARCangel4 and AXS10x are FPGA-based boards so they may have
different CPUs. For now we have only 1 option (ARC700) and we define
this as default in arch Kconfig.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
"reset.c" and "cpu.c" have no architecture-specific code at all.
Others are applicable to either ARC CPU.
This change is a preparation to submission of ARCv2 architecture port.
Even though ARCv1 and ARCv2 ISAs are not binary compatible most of
built-in modules still have the same programming model - AUX registers
are mapped in the same addresses and hold the same data (new featues
extend existing ones).
So only low-level assembly code (start-up, interrupt handlers) is left
as CPU(actually ISA)-specific. This significantyl simplifies maintenance
of multiple CPUs/ISAs.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
* use better symbols for relocatable region boundaries
("__image_copy_start" instead of "CONFIG_SYS_TEXT_BASE")
* remove useless debug messages because they will only show up in case
of both problem (when normal "if" branch won't be taken) and DEBUG take
place which is pretty rare situation.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Even though existing implementation works fine in preparation to
submission of ARCv2 architecture we need this change.
In case of ARCv2 interrupt vector table consists of just addresses
of corresponding handlers. And if those addresses will be in .text
section then assembler will encode them as everything in .text section
as middle-endian and then on real execution CPU will read swapped
addresses and will jump into the wild.
Once introduced new section is situated so .text section remains the
first which allows us to use common linker option for linking everything
to a specified CONFIG_SYS_TEXT_BASE.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Depending on MMU presence in CPU there're differences in HW behavior.
For example address of instruction that caused exception is put in
ECR register if MMU exists and in ERET register otherwise.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
To disable interrupts we need to reset corresponding flags in STATUS32
register. For this we need to OR flags for interrupts level1 and level2
and then AND with current value in STATUS32.
Before that implementation was incorrect.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Exception cause register (ECR) contains value that describes a reason
for exception that has happened. This helps a lot to figure-out what
went wrong.
Now we print this register contents when dumping registers.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
Some cache operations ({i|d}cache_{enable|disable|status} or
flush_dcache_all) are built and used even if CONFIG_SYS_{I|D}CACHE_OFF
is set.
This is required for force disable of caches on early boot.
What if something was executed before U-boot and enabled caches
(low-level bootloaders, previously run kernel etc.)?
But if CPU doesn't really have caches any attempt to access
cache-related AUX registers triggers instruction error exception.
So for convenience we'll try to avoid exceptions by checking if CPU
actually has caches (we check separately data and instruction cache
existence) at all.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Igor Guryanov <guryanov@synopsys.com>
The axp221 / axp223's N_VBUSEN pin can be configured as an output rather
then an input, and this is used on some boards to control usb-vbus0, add
support for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Most of the usb-controller init code found in ehci-sunxi.c also is necessary
to init the otg usb controller, so move it to a common place.
While at it also update various #ifdefs / defines for sun8i support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
"adr rX, text_end" only works if the label is close. Adding further code
to the other functions will prevent this. So move the containing
function close to label. No functional change.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Based on the original version by Marc Zyngier. It adds a psci_cpu_off
implementation for the A20 SoC. The mechanism works by first preparing
the calling CPU to go offline (disable and flush cache, disable SMP),
then requesting CPU 0 to pull the plug. The request is sent as FIQ on
SGI15.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for VGA directly from the sunxi SoC / display engine.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add lcd output support, see the new Kconfig entries and doc/README.video for
how to enable / configure this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify sunxi_lcdc_pll_set to work with both tcon0 and tcon1, this is a
preparation patch for adding lcd support.
While at it also swap the divider search order, searching from low to
high, as the comment above the code says we should do. In cases where there
are multiple solutions this will result in picking a lower pll clock and
divider, which is more stable and saves power.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Some boards use GPIO-s on the pmic, one example of this is the A13-OLinuXino
board, which uses gpio0 of the axp209 for the lcd-power signal.
This commit adds support for gpio pins on the AXP209 pmic, the sunxi_gpio.c
changes are universal, adding gpio support for the other AXP pmics (when
necessary) should be a matter of adding the necessary axp_gpio_foo functions
to their resp. drivers, and add "#define AXP_GPIO" to their header file.
Note this commit only adds support for the non device-model version of the
gpio code, patches for adding support to the device-model version are very
welcome.
The string representation for these gpio-s is AXP0-#, the 0 in the AXP0 prefix
is there in case we need to support gpio-s on more then 1 pmic in the future.
At least A80 boards have 2 pmics, and we may end up needing to support gpio-s
on both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move a few mux defines around so that all the mux defines are properly sorted
by port number.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a write to the "unknown" (*) register to enable auto input sync, when
initially adding sunxi hdmi output support this magic write from the android
kernel code was missed, causing lcdc -> hdmi encoder sync problems.
With this write added, we can drop the modesetting retries and the extra
delays added to work around these sync problems.
With the retries dropped there also is no need to 0 all the enable flags at
the beginning of the modeset, as they are initialized to 0 already by
engines_init.
*) "unknown" is the actual name of this register in the android kernel sources
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
So far we've been programming the hdmi-encoder to send out dvi data over the
hdmi connector. This works well for most devices, including hdmi devices, but
not all devices accept dvi data on a hdmi input.
Add support for sending proper hdmi data over the hdmi output found on most
sunxi boards. This can be turned on by adding monitor=hdmi as option to the
video-mode env. variable.
A follow up patch will determine whether to send dvi or hdmi automatically when
EDID is used.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
Add DDC & EDID support and use it to automatically select the native mode of
the attached monitor. This can be disabled by adding edid=0 as option
to the video-mode env. variable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Acked-by: Anatolij Gustschin <agust@denx.de>
PLL1 on sun6i / sun8i also has a p factor which divides the clock by
2^p (to the power p). On sun6i the p factor is ignored, but on sun8i it is
used and we were setting it to 1, resulting in the CPU running at 504 MHz
instead of 1008 MHz, this commit fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
After reboot, reset or even short power off, DRAM typically retains
the old stale data for some period of time (for this type of memory,
the bits of data are stored in slowly discharging capacitors).
The current sun6i/sun8i DRAM size detection logic, which is
inherited from the Allwinner code, relies on using a large magic
signature with the hope that it is unique enough and unlikely to
ever accidentally match this leftover garbage data in RAM. But
this approach is inherently unsafe, as can be demonstrated using
the following test program:
/***** A testcase for reproducing the problem ******/
void main(int argc, char *argv[])
{
size_t size, i;
uint32_t *buf;
/* Allocate the buffer */
if (argc < 2 || !(size = (size_t)atoi(argv[1]) * 1048576) ||
!(buf = malloc(size))) {
printf("Need buffer size in MiB as a cmdline argument\n");
exit(1);
}
/* Fill it with the Allwinner DRAM "magic" values */
for (i = 0; i < size / 4; i++)
buf[i] = 0xaa55aa55 + ((uintptr_t)&buf[i] / 4) % 64;
/* Try to reboot */
system("reboot");
/* And wait */
for (;;) {}
}
/***************************************************/
If this test program is run on the device (giving it a large
chunk of memory), then the DRAM size detection logic in u-boot
gets confused after reboot and fails to initialize DRAM properly.
A better approach is not to rely on luck and abstain from making
any assumptions about the properties of the leftover garbage
data in RAM. Instead just use a more reliable code for testing
whether two different addresses refer to the same memory location.
Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Based on the register / dram_para headers from the Allwinner u-boot / linux
sources + the init sequences from boot0.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i boot0 code fills the DRAM with a "random" pattern before comparing
it at different offsets to do columns, etc. detection. The sun6i boot0 code
does not do it, instead relying on the memory contents being random enough
to begin with for the memcmp to properly detect the wrap-around address, iow
it is working purely by chance. Since our sun6i dram code was modelled after
the boot0 code it contained the same issue.
This commit fixes this by filling the memory with a unique, distinct pattern.
The new mctl_mem_fill function this introduces is added as an inline helper
in dram.h, so that it can be shared with the sun8i dram code.
While at it move mctl_mem_matches to dram.h for re-use in sun8i too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The await_completion helper is already copy pasted between the sun4i and sun6i
dram code, and we need it for sun8i too, so lets make it an inline helper in
dram.h, rather then adding yet another copy.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Our old hardcoded k and m values are based on PLL5 being configured in steps
of 48 MHz, which is correct for sun6i where the DRAM PLL runs at twice the
DRAM CLK, which is usually configured in 24 MHz step. But on the A23 (sun8i)
the PLL5 runs at half the DRAM CLK, so we require 12 MHz steps.
This commit adjusts clock_set_pll5 to automatically select the best k and m
depending on the requested clk rate.
Suggested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sun8i dram code sometimes wants to enable sigma delta mode,
add a parameter to allow this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The axp223 appears to be the same as the axp221, except that it uses the
rsb to communicate rather then the p2wi. At least all the registers we use
are 100% the same.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
sun8i (A23) introduces a new bus for communicating with the pmic, the rsb,
the rsb is also used to communicate with the pmic on the A80, and is
documented in the A80 user manual.
This commit adds support for this based on the rsb driver from the allwinner
u-boot sources.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The p2wi interface is only available on sun6i, adjust the gpio pinmux and
base address defines for it to reflect this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
0x400 is true 1K.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
On sun6i the SID is stored in the pmic, rather then in the SoC itself,
add a helper function to abstract this away.
This makes our MAC address generation code also work on sun6i.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi mmc controller has both an internal clock divider, as well as
the divider in the mod0-clk for the mmc controller.
The internal divider cannot be used, as it conflicts with the setting of
clock sampling phases which is done in the mod0-clk, so it must be set to
0 (divide by 1).
For some reason while the kernel has had this correct from day one, the
u-boot sunxi mmc code has been using a fixed mod0-clk and setting its
internal divider depending on the desired speed. This is something which
we've inherited from the original Allwinner u-boot sources, but while this
has been fixed in Allwinner's own u-boot code at least for the A23 and later
upstream u-boot was still doing this wrong.
This commit fixes this, thereby also fixing mmc support not working reliable
on the A23 (which seems more sensitive to this) and possible also fixes some
other sunxi mmc issues.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The A31s only has one dram channel, so do not bother with trying to initialize
a second channel.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add a sunxi_get_ss_bonding_id() function, and use it to differentiate between
the A31s and the A31.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
It turns out that there is a too large spread between boards to handle this
with a default value, turn this into Kconfig options, and set the values
the factory images are using for the Colombus and Mele_M9 boards.
Note this changes the ZQ default when not overriden through defconfig from
120 to 123, as that is what most boards seem to actually use.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Switch to using hardware leveling for certain parameters on the EMIF
rather than using precalculated values. Doing this also means we have a
common place now between am437x and am335x for setting
emif_sdram_ref_ctrl with a value for the correct delay length.
Tested-by: Felipe Balbi <balbi@ti.com>
Tested-by: Tom Rini <trini@ti.com>
Signed-off-by: James Doublesin <doublesin@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Configure coreboot pci memory regions so that pci device drivers
could work correctly.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Change SYS_CONFIG_NAME and DEFAULT_DEVICE_TREE to chromebook_link
which is currently the only real board officially supported to run
U-Boot loaded by coreboot.
Note the symbolic link file chromebook_link.dts is deleted and
link.dts is renamed to chromebook_link.dts.
To avoid multiple definition of video_hw_init, the CONFIG_VIDEO_X86
define needs to be moved to arch/x86/cpu/ivybridge/Kconfig.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are many places in the U-Boot source tree which refer to
CONFIG_SYS_COREBOOT, CONFIG_CBMEM_CONSOLE and CONFIG_VIDEO_COREBOOT
that is currently defined in coreboot.h.
Move them to arch/x86/cpu/coreboot/Kconfig so that we can switch
to board configuration file to build U-Boot later.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
When CONFIG_X86_RESET_VECTOR is not selected, specifying the ROM chip
size is meaningless, hence hide it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert CONFIG_X86_RESET_VECTOR and CONFIG_SYS_X86_START16 to Kconfig
options so that we can remove them from board configuration file.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
By default U-Boot automatically calibrates TSC running frequency via
MSR and PIT. The calibration may not work on every x86 processor, so
a new Kconfig option CONFIG_TSC_CALIBRATION_BYPASS is introduced to
allow bypassing the calibration and assign a hardcoded TSC frequency
CONFIG_TSC_FREQ_IN_MHZ.
Normally the bypass should be turned on in a simulation environment
like qemu.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
If coreboot is built with CONFIG_COLLECT_TIMESTAMPS, use the value
of base_time in coreboot's timestamp table as our timer base,
otherwise TSC counter value will be used.
Sometimes even coreboot is built with CONFIG_COLLECT_TIMESTAMPS,
the value of base_time in the timestamp table is still zero, so
we must exclude this case too (this is currently seen on booting
coreboot in qemu).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
These two are not worth having separate inline functions as they are
really simple, so drop them.
Also changed 'type' parameter of fsp_get_next_hob() from u16 to uint.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
It is useful to be able to see the MTRR setup in U-Boot. Add a command
to list the state of the variable MTRR registers and allow them to be
changed.
Update the documentation to list some of the available commands.
This does not support fixed MTRRs as yet.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
At present the normal update (which happens much later) does not work. This
seems to have something to do with the 'no eviction' mode in the CAR, or at
least moving the microcode update after that causes it not to work.
For now, do an update early on so that it definitely works. Also refuse to
continue unless the microcode update check (later in boot) is successful.
Signed-off-by: Simon Glass <sjg@chromium.org>
For platforms with CAR we should disable it before relocation. Check if
this function is available and call it if so.
Signed-off-by: Simon Glass <sjg@chromium.org>
Cache-as-RAM should be turned off when we relocate since we want to run from
RAM. Add a function to perform this task.
Signed-off-by: Simon Glass <sjg@chromium.org>
Once we stop running from ROM we should set up the MTTRs to speed up
execution. This is only needed for platforms that don't have an FSP.
Also in the Coreboot case, the MTRRs are set up for us.
Signed-off-by: Simon Glass <sjg@chromium.org>
We should use MTRRs to speed up execution. Add a list of MTRR requests which
will dealt with when we relocate and run from RAM.
We set RAM as cacheable (with write-back) and registers as non-cacheable.
Signed-off-by: Simon Glass <sjg@chromium.org>
Set the frame buffer to write-combining. This makes it faster, although for
scrolling write-through is even faster for U-Boot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Memory Type Range Registers are used to tell the CPU whether memory is
cacheable and if so the cache write mode to use.
Clean up the existing header file to follow style, and remove the unneeded
code.
These can speed up booting so should be supported. Add these to global_data
so they can be requested while booting. We will apply the changes during
relocation (in a later commit).
Signed-off-by: Simon Glass <sjg@chromium.org>
This is set up along with CAR (Cache-as-RAM) anyway. When we relocate we
don't really need ROM caching (we read the VGA BIOS from ROM but that is
about it)
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are some bits which should be ignored when displaying the mode number.
Make sure that they are not included in the mode that is displayed.
Signed-off-by: Simon Glass <sjg@chromium.org>
There is no need to run with the cache disabled, and there is no point in
clearing the display frame buffer since U-Boot does it later.
Signed-off-by: Simon Glass <sjg@chromium.org>
This takes about about 700ms on link when running natively and 900ms when
running using the emulator. It is a waste of time if video is not enabled,
so don't bother running the video BIOS in that case.
We could add a command to run the video BIOS later when needed, but this is
not considered at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We don't need this in U-Boot since we calculate it based on available memory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Topcliff PCH has 4 UART devices integrated (Device 10, Funciton
1/2/3/4). Add the corresponding device nodes in the crownbay.dts per
Open Firmware PCI bus bindings.
Also a comment block is added for the 'stdout-path' property in the
chosen node, mentioning that by default the legacy superio serial
port (io addr 0x3f8) is still used on Crown Bay as the console port.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use ePAPR defined properties for x86-uart: clock-frequency and
current-speed. Assign the value of clock-frequency in device tree
to plat->clock of x86-uart instead of using hardcoded number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Remove the troublesome union hob_pointers so that some annoying casts
are no longer needed in those hob access routines. This also improves
the readability.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Introduce a gd->hose to save the pci hose in the early phase so that
apis in drivers/pci/pci.c can be used before relocation. Architecture
codes need assign a valid gd->hose in the early phase.
Some variables are declared as static so change them to be either
stack variable or global data member so that they can be used before
relocation, except the 'indent' used by CONFIG_PCI_SCAN_SHOW which
just affects some print format.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
On x86, some peripherals on pci buses need to be accessed in the
early phase (eg: pci uart) with a valid pci memory/io address,
thus scan the pci bus and do the corresponding resource allocation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
arch/x86/cpu/pci.c has access to the U-Boot global data thus
DECLARE_GLOBAL_DATA_PTR is needed.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commits cleans up the board dts files.
- Correct the serial port register size to 8
- Remove the misleading status = "disabled" statement in the
serial.dtsi
- Move the inclusion of skeleton.dtsi from serial.dtsi to board
dts files
- Let the board dts file define stdout-path in the chosen node
- Remove device nodes in board dts files thar are duplicated to
skeleton.dtsi
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The name of coreboot.dtsi is misleading, as it actually describes
the legacy serial port device node.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
MetaWare debugger (MDB) is still used as a primary tool for interaction
with target via JTAG. Moreover some very advanced features are not yet
implemented in GDB for ARC (and not sure if they will be implemnted
sometime soon given complexity and rare need for those features for
common user).
So if we're talking about development process when U-Boot is loaded in
target memory not by low-level boot-loader but manually through JTAG
chances are high developer uses MDB for it.
But MDB doesn't support PIE (position-independent executable) - it will
refuse to even start - that means no chance to load elf contents on
target.
Then the only way to load U-Boot in MDB is to fake it by:
1. Reset PIE flag in ELF header
This is simpe - on attempt to open elf MDB checks header and if it
doesn't match its expectation refuces to use provided elf.
2. Strip all debug information from elf
If (1) is done then MDB will open elf but on parsing of elf's debug
info it will refuse to process due to debug info it cannot understand
(symbols with PIE relocation).
Even though it could be done manually (I got it documented quite a while
ago here http://www.denx.de/wiki/U-Boot/ARCNotes) having this automated
way is very convenient. User may build U-Boot that will be loaded on
target via MDB saying "make mdbtrick".
Then if we now apply the manipulation MDB will happily start and will
load all required sections into the target.
Indeed there will be no source-level debug info available. But still MDB
will do its work on showing disassembly, global symbols, registers,
accessing low-level debug facilities etc.
As a summary - this is a pretty dirty hack but it simplifies life a lot
for us ARc developers.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Resynchronize memcpy/memset with kernel 3.17 and build them in
Thumb2 mode (unified syntax). Those assembler files can be built
and linked in ARM mode too, however when calling them from Thumb2
built code, the stack got corrupted and the copy did not succeed
(the exact details have not been traced back). However, the Linux
kernel builds those files in Thumb2 mode. Hence U-Boot should
build them in Thumb2 mode too when CONFIG_SYS_THUMB_BUILD is set.
To build the files without warning, some assembler instructions
had to be replaced with their UAL compliant variant (thanks
Jeroen for this input).
To build the file in Thumb2 mode the implicit-it=always option need
to be set to generate Thumb2 compliant IT instructions where needed.
We add this option to the general AFLAGS when building for Thumb2.
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Since commit 3ff46cc42b ("arm: relocate the exception vectors") mx25pdk
hangs like this:
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: WDOG
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
(hangs)
Add a specific relocate_vectors macro that skips the vector relocation, as the
i.MX25 SoC does not provide RAM at the high vectors address (0xFFFF0000), and
(0x00000000) maps to ROM.
This allows mx25 to boot again.
Acked-By: Bill Pringlemeir <bpringlemeir@nbsps.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently there is an unneeded empty line after printing the reset cause:
U-Boot 2015.01-rc4-00080-g0551a93 (Jan 06 2015 - 13:04:19)
CPU: Freescale i.MX25 rev1.2 at 399 MHz
Reset cause: POR
Board: MX25PDK
I2C: ready
DRAM: 64 MiB
MMC: FSL_SDHC: 0
Remove the extra "\n" when printing the reset cause.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The low-level debugging functions are useful to debug the early boot
stage where the full UART driver is not available.
UniPhier SoCs need to initialize the UART port 0 to use this feature.
The initialization routine is called at the very entry of the
lowlevel_init().
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
For NAND boot on PH1-LD4, PH1-sLD8, and some other SoCs,
the output of the system bus is disabled by default.
It must be enabled by software to have access to the system bus.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The max size of available memories on slot0 and slot1 is 32MB because
- EA[25] signal is not output on the save-pin mode which is
used PH1-LD4 or later SoCs.
- EA[25] signal is not connected by the limitation (or bug?) of
the PLD logic of DCC support card.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This optional DT property is called 'num-cs', so repair the misnomers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Linux now also contains SPI driver, yet the name is 'snps,dw-apb-ssi'.
Fix the naming before we have to support both names.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The ChromeOS EC keyboard is used by various different chromebooks. Peach
pi being the third board in the u-boot tree to use it (snow and peach
pit the other two). Rather then embedding the same big DT node in the
peach-pi DT again, copy the dtsi snippit & bindings documentation from
linux and include it in all 3 boards.
This slightly changes the dt bindings in u-boot:
* google,key-rows becomes keypad,num-rows
* google,key-colums becomes keypad,num-colums
* google,repeat-delay-ms and google,repeat-rate-ms are no longer used
and replaced by hardcoded values (similar to tegra kbc)
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
pci ports are used as root complex in Linux. So set this as default
in u-boot for keystone devices
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
On OMAP platforms (like OMAP5) Linux kernel fails to detect a SATA
device if it is used by U-Boot.
It happens because U-Boot does not reset SATA controller before boot.
Reset the controller on OS boot so that Linux will have a clean state
to work with.
Signed-off-by: Dmitry Lifshitz <lifshitz@compulab.co.il>
Reviewed-by: Tom Rini <trini@ti.com>
Part of DMM logic is reuse from commit
47a4bea6af ("ARM: omap4: Update sdram
setting for panda rev A6") Which broke SDP4430 with ES2.3 (uses old
DDR).
So, to maintain support for newer DDR used in Panda ES rev B3, we
should, in addition to the commit
675cc77a3a ("ARM:OMAP4+: panda-es: Support
Rev B3 Elpida DDR2 RAM"), DDR timings, also do DMM configuration
specific to Panda.
Signed-off-by: Nishanth Menon <nm@ti.com>
The gd will be cleared at first so we don't need to set arch.tbl to 0.
In addition, the checks later against lastinc also work fine with an
initial value of 0 here. This also brings us in line with sunxi code
for example.
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In both SPL and non-SPL cases we will make a call to timer_init() early
on and do not need to call it again within s_init().
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The save_boot_params function here is the same as the default weak one
from arch/arm/cpu/armv7/start.S, drop.
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 8bc347e2ec "ARM: bootm: Allow booting in secure mode on hyp capable
systems" added the capability to select nonsec vs sec mode boot via an
environment var.
There is a subtle gotcha with this functionality, which is that the PSCI nodes
are still created in the fdt (via armv7_update_dt->fdt_psci) even when booting
in secure mode. Which means that if the kernel is PSCI aware then it will fail
to boot because it will try and do PSCI from secure world, which won't work.
This likely didn't get noticed before because the original purpose was to
support booting the legacy linux-sunxi kernels which don't understand PSCI.
To fix expose boot_nonsec (renaming with armv7_ prefix) outside of bootm.c and
use from the virt-dt code.
As well as avoiding the creation of the PSCI nodes we should also avoid
reserving the secure RAM, so do so.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Tom Rini <trini@ti.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
All the MPC824X boards are still non-generic boards:
A3000, CPC45, CU824, eXalion, MVBLUE, MUSENKI, Sandpoint824x, utx8245
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Josef Wagner <Wagner@Microsys.de>
Cc: Torsten Demke <torsten.demke@fci.com>
Cc: Jim Thompson <jim@musenki.com>
Cc: Greg Allen <gallen@arlut.utexas.edu>
These boards are still non-generic boards.
drivers/rtc/ds12887.c should also be removed because it can not
be built without CONFIG_ATC.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
This board is still a non-generic board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Jerry Van Baren <gerald.vanbaren@smiths-aerospace.com>
This board is still a non-generic board.
Unused code in arch/powerpc/cpu/mpc8xx/video.c should be also deleted
because CONFIG_VIDEO_ENCODER_AD7176, CONFIG_VIDEO_ENCODER_AD7177,
CONFIG_VIDEO_ENCODER_AD7179 are not defined any more.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
These boards are still non-generic boards.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Stefan Roese <sr@denx.de>
The malloc() calls are unnecessary, just allocate the stuff on stack.
While at it, reorder the code a little, so that only one variable is
used for the text, use snprintf() instead of sprintf() and use %01d
as a formatting string to avoid any possible overflows.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Nikita Kiryanov <nikita@compulab.co.il>
Cc: Sean Cross <xobs@kosagi.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Christian Gmeiner <christian.gmeiner@gmail.com>
This commit adds a dump command of DDR PHY parameters of UniPhier
SoC family. It might not be used very often for the regular operation
but it would be useful when something goes wrong with DDR memories.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This training code provides run-time adjustment of DDR PHY parameters
for stable DDR operation.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
enable this clock with the following:
clk_usb_otg_enable((void *)HSOTG_BASE_ADDR)
Signed-off-by: Steve Rae <srae@broadcom.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Add a board rev entry for the new model A+, and augment the board
rev error handling code to be a bit more verbose.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
By rearranging the functions in the semihosting code we can
avoid forward-declaration of the internal static functions.
This puts the stuff in a logical order: read/open/close/len
and then higher-order functions follow at the end.
Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is currently a regression when using newer ARM64 compilers
for semihosting: the way long types are inferred from context
is no longer the same.
The semihosting runtime uses long and size_t, so use this
explicitly in the semihosting code and interface, and voila:
the code now works again.
Tested with aarch64-linux-gnu-gcc: Linaro GCC 4.9-2014.09.
Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Suggested-by: Mark Hambleton <mark.hambleton@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The semihosting code exposes internal file handle handling
functions to read(), open(), close() and get the length of
a certain file handle.
However the code using it is only interested in either
reading and entire named file into memory or getting the
file length of a file referred by name. No file handles
are used.
Thus make the file handle code internal to this file by
removing these functions from the semihosting header file
and staticize them.
This gives us some freedom to rearrange the semihosting
code without affecting the external interface.
Cc: Darwin Rambo <drambo@broadcom.com>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Mark Hambleton <mark.hambleton@arm.com>
Cc: Tom Rini <trini@ti.com>
Acked-by: Steve Rae <srae@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MMC of exynos5420 can select SPLL as source clock, so add to support
SPLL in exynos5420_get_mmc_clk(). It was tested on Odroid-XU3 board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Add samsung,vbus-gpio information for the XU3. This allows the usage of
the EHCI controller on the XU3, which is connected to the SMSC LAN9514
chip (usb hub + network).
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Not all exynos 5420 based devices with an LCD also have a parade LVDS
bridge. So make sure compilation doesn't break if CONFIG_LCD is enabled
and CONFIG_VIDEO_PARADE is not.
As a side-effect move the parade functions from the exynos system header
file to its own file.
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Unlike the Peach-Pit board, there is no parade edp to lvds bridge on the
Pi. So drop it from device-tree
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This patch adds support for Odroid-XU3.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Reviewed-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Tested-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The current current watchdog timeout of 12 seconds is a bit small for
booting into Linux, especially when using a NFS based rootfs. So lets
change this timeout to a more defensive value of 30 seconds.
Also we now call the hw_watchdog_init() function so that we override
the value already configured from the Preloader.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
mxc_get_clock's return type is unsigned int. 'return -1' is same with
'return 0xffffffff', so 0 should be used as the return value when
unsupported mxc_clock type is passed to mxc_get_clock.
Also include an err message when unsupported mxc_clock type is passed
to mxc_get_clock.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
This is the follow-on patch to clean up the FSP support codes:
- Remove the _t suffix on the structures defines
- Use __packed for structure defines
- Use U-Boot's assert()
- Use standard bool true/false
- Remove read_unaligned64()
- Use memcmp() in the compare_guid()
- Remove the cast in the memset() call
- Replace some magic numbers with macros
- Use panic() when no valid FSP image header is found
- Change some FSP utility routines to use an fsp_ prefix
- Add comment blocks for asm_continuation and fsp_init_done
- Remove some casts in find_fsp_header()
- Change HOB access macros to static inline routines
- Add comments to mention find_fsp_header() may be called in a
stackless environment
- Add comments to mention init(¶ms) in fsp_init() cannot
be removed
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are two standard SD card slots on the Crown Bay board, which
are connected to the Topcliff PCH SDIO controllers. Enable the SDHC
support so that we can use them.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The Crown Bay board has an SST25VF016B flash connected to the Tunnel
Creek processor SPI controller used as the BIOS media where U-Boot
is stored. Enable this flash support.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Intel Tunnel Creek GPIO register block is compatible with current
ich6-gpio driver, except the offset and content of GPIO block base
address register in the LPC PCI configuration space are different.
Use u16 instead of u32 to store the 16-bit I/O address of the GPIO
registers so that it could support both Ivybridge and Tunnel Creek.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
To avoid having two microcode formats, adjust the build system to support
obtaining the microcode from the device tree, even in the case where it
must be made available before the device tree can be accessed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Implement minimum required functions for the basic support to
queensbay platform and crownbay board.
Currently the implementation is to call fsp_init() in the car_init().
We may move that call to cpu_init_f() in the future.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Integrate the processor microcode version 1.05 for Tunnel Creek,
CPUID device 20661h.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are several problems in the code. The device tree decode is incorrect
in ways that are masked due to a matching bug. Both are fixed. Also
microcode_read_rev() should be inline and called before the microcode is
written.
Note: microcode writing does not work correctly on ivybridge for me. Further
work is needed to resolve this. But this patch tidies up the existing code
so that will be easier.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are new microcode revisions available. Update them. Also change
the format so that the first 48 bytes are not omitted from the device tree
data.
Signed-off-by: Simon Glass <sjg@chromium.org>
We might end up with a few of these, so put them in their own directory.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Implement an API that can be used by drivers to allocate memory from a
pool that is mapped uncached. This is useful if drivers would otherwise
need to do extensive cache maintenance (or explicitly maintaining the
cache isn't safe).
The API is protected using the new CONFIG_SYS_NONCACHED_MEMORY setting.
Boards can set this to the size to be used for the non-cached area. The
area will typically be right below the malloc() area, but architectures
should take care of aligning the beginning and end of the area to honor
any mapping restrictions. Architectures must also ensure that mappings
established for this area do not overlap with the malloc() area (which
should remain cached for improved performance).
While the API is currently only implemented for ARM v7, it should be
generic enough to allow other architectures to implement it as well.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Jetson TK1 has an ethernet NIC connected to the PCIe bus and routes
the second root port to a miniPCIe slot. Enable the PCIe controller and
the network driver to allow the device to boot over the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra124 SoCs.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree node for the GIC v2 found on the Cortex-A15 CPU
complex of Tegra124. U-Boot doesn't use this but subsequent patches will
add device tree nodes that reference it by phandle.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The Beaver has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network device driver so that the device can
boot over the network.
In addition the board has a mini-PCIe expansion slot.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The PCIe bus on Cardhu is routed to the dock connector. An ethernet NIC
is available on the dock over the PCIe bus. Enable the PCIe controller
and the network device driver so that the device can boot over the
network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra30 SoCs.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add a device tree node for the GIC found on Tegra30. U-Boot doesn't use
it directly but subsequent patches will add device tree nodes that
reference it by phandle.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The TrimSlice has an ethernet NIC connected to the PCIe bus. Enable the
PCIe controller and the network driver so that the device can boot over
the network.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the device tree node for the PCIe controller found on Tegra20 SoCs.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Add the PCIe and SATA lane configuration to the Jetson TK1 device tree,
so that the XUSB pad controller can be appropriately configured.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The XUSB pad controller is used for pinmuxing of the XUSB, PCIe and SATA
lanes.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This controller was introduced on Tegra114 to handle XUSB pads. On
Tegra124 it is also used for PCIe and SATA pin muxing and PHY control.
Only the Tegra124 PCIe and SATA functionality is currently implemented,
with weak symbols on Tegra114.
Tegra20 and Tegra30 also provide weak symbols for these functions so
that drivers can use the same API irrespective of which SoC they're
being built for.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
Implement the powergate API that allows various power partitions to be
power up and down.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This reset is required for PCIe and the corresponding ID therefore needs
to be defined. The enumeration value for this was properly defined on
some SoCs but not on others. Similarly, some contained it in the mapping
of peripheral IDs to clock IDs, other didn't. This patch defines it
consistently for all supported SoC generations.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
This function is required by PCIe and SATA. This patch implements it on
Tegra20, Tegra30 and Tegra124. It isn't implemented for Tegra114 because
it doesn't support PCIe or SATA.
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Warren <twarren@nvidia.com>
The property name of the "aliases" node should be "serial*"
to assign a desired number for the device sequence number.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Not all portals might be managed and therefore visible.
Set the isdr register so that the corresponding isr register
won't be set. This is required when supporting power management.
Signed-off-by: Jeffrey Ladouceur <Jeffrey.Ladouceur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit f29f804a93 generalized the TLB
mapping function, but made the DDR mapping leftover size to zero,
causing the message not printed.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alexander Graf <agraf@suse.de>
CC: Scott Wood <scottwood@freescale.com>
Commit 65dd74a674 (x86: ivybridge: Implement SDRAM init) introduced
x86-specific asmlinkage into arch/x86/include/asm/config.h.
Commit ed0a2fbf14 (x86: Add a definition of asmlinkage) added the
same macro define again, this time, into include/common.h.
(Please do not add arch-specific stuff to include/common.h any more;
it is already too cluttered.)
The generic asmlinkage is defined in <linux/linkage.h>. If you want
to override it with an arch-specific one, the best way is to add it
to <asm/linkage.h> like Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
FSP builds a series of data structures called the Hand-Off-Blocks
(HOBs) as it progresses through initializing the silicon. These data
structures conform to the HOB format as described in the Platform
Initialization (PI) specification Volume 3 Shared Architectual
Elements specification, which is part of the UEFI specification.
Create a simple command to parse the HOB list to display the HOB
address, type and length in bytes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Per Intel FSP architecture specification, FSP provides 3 routines
for bootloader to call. The first one is the TempRamInit (aka
Cache-As-Ram initialization) and the second one is the FspInit
which does the memory bring up (like MRC for other x86 targets)
and chipset initialization. Those two routines have to be called
before U-Boot jumping to board_init_f in start.S.
The FspInit() will return several memory blocks called Hand Off
Blocks (HOBs) whose format is described in Platform Initialization
(PI) specification (part of the UEFI specication) to the bootloader.
Save this HOB address to the U-Boot global data for later use.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Use inline assembly codes to call FspNotify() to make sure parameters
are passed on the stack as required by the FSP calling convention.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
This is the initial import from Intel FSP release for Queensbay
platform (Tunnel Creek processor and Topcliff Platform Controller
Hub), which can be downloaded from Intel website.
For more details, check http://www.intel.com/fsp.
Note: U-Boot coding convention was applied to these codes, so it
looks completely different from the original Intel release.
Also update FSP support codes license header to use SPDX ID.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
On most x86 boards, the legacy serial ports (io address 0x3f8/0x2f8)
are provided by a superio chip connected to the LPC bus. We must
program the superio chip so that serial ports are available for us.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Movie setup_pch_gpios() in the ich6-gpio driver to the board support
codes, so that the driver does not need to know any platform specific
stuff (ie: include the platform specifc chipset header file).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Move GD_BIST from lib/asm-offsets.c to arch/x86/lib/asm-offsets.c
as it is x86 arch specific stuff. Also remove GENERATED_GD_RELOC_OFF
which is not referenced anymore.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Currently the ROM_SIZE is hardcoded to 8MB in arch/x86/Kconfig. This
will not be the case when adding additional board support. Hence we
make ROM_SIZE configurable (512KB/1MB/2MB/4MB/8MB/16MB) and have the
board Kconfig file select the default ROM_SIZE.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
This converts all Tegra boards over to use driver model for I2C. The driver
is adjusted to use driver model and the following obsolete CONFIGs are
removed:
- CONFIG_SYS_I2C_INIT_BOARD
- CONFIG_I2C_MULTI_BUS
- CONFIG_SYS_MAX_I2C_BUS
- CONFIG_SYS_I2C_SPEED
- CONFIG_SYS_I2C
This has been tested on:
- trimslice (no I2C)
- beaver
- Jetson-TK1
It has not been tested on Tegra 114 as I don't have that board.
Acked-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Simon Glass <sjg@chromium.org>
Nyan-big is a Tegra124 clamshell board that is very similar to venice2, but
it has a different panel, the sdcard cd and wp sense are flipped, and it has
a different revision of the AS3722 PMIC.
This is the Acer Chromebook 13 CB5-311-T7NN (13.3-inch HD, NVIDIA
Tegra K1, 2GB). The display is not currently supported, so it should
boot on other nyan-based Chromebooks also, but only the device tree for
nyan-big is provided here.
The device tree file is from Linux but with features removed which are
unlikely to be supported in U-Boot soon (regulators, pinmux). Also the
addresses are updated to 32-bit.
Signed-off-by: Allen Martin <amartin@nvidia.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
(rebase, change to 'nyan-big', fix pinmux that resets nyan-big)
Sync this up with Linux v3.18-rc5. Exclude features that are unlikely to
supported in U-Boot soon (regulators, pinmux). Also the addresses are
updated to 32-bit. Otherwise it is the same. Also bring in the dt-bindings
for pinctrl.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
This will be used by nyan-big, but bring it in in a separate patch since it
will be common to other boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an I2C bus to the device tree, with an EEPROM emulator attached to one
of the addresses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
To enable testing of I2C, add a simple I2C EEPROM simulator for sandbox.
It supports reading and writing from a small data store.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
As NOR/NAND/SD boot are all supported on LS1021AQDS/TWR
boards, the prompt message "Support ls1021aqds_nor" in
Kconfig is not clear. This patch changes it to
"Support ls1021aqds".
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS1 has 4 SMMUs for address translation of the masters. All the
SMMUs' stream IDs are 8-bit. The address translation depends on the
stream ID of the incoming transaction.
Each master has unique stream ID assigned to it and is configurable
through SCFG registers. The stream ID for the masters is identical
and share the same register field of STREAM ID registers.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The Central Security Unit (CSU) allows secure world software to
change the default access control policies of peripherals/bus
slaves, determining which bus masters may access them. This
allows peripherals to be separated into distinct security domains.
Combined with SMMU configuration of the system masters privileges,
these features provide protection against indirect unauthorized
access to data.
For now we configure all the peripheral access permissions as R/W.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Enable hypervisors utilizing the ARMv7 virtualization extension
on the LS1021A-QDS/TWR boards with the A7 core tile, we add the
required configuration variable.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Define the board specific smp_set_cpu_boot_addr() function to set
the start address for secondary cores in the LS1021A specific manner.
Define the board specific smp_kick_all_cpus() functioin to boot a
secondary core. Here the BRR contains control bits for enabling boot
for each core. On exiting HRESET or PORESET, the RCW BOOT_HO field
optionally allows for logical core 0 to be released for booting or to
remain in boot holdoff. All other cores remain in boot holdoff until
their corresponding bit is set.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For some SoCs, the system clock frequency may not equal to the
ARCH Timer's frequency.
This patch uses the CONFIG_TIMER_CLK_FREQ instead of
CONFIG_SYS_CLK_FREQ, then the system clock macro and arch timer
macor could be set separately and without interfering each other.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
For some SoCs, the pen address register maybe in BE mode and the
CPUs are in LE mode.
This patch adds BE mode support for smp pen address.
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
move usb device tree fixup code from "arch/powerpc/" to "drivers/usb/"
so that it works independent of architecture it is running on
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds QSPI boot support for LS1021AQDS/TWR board.
The QSPI boot image need to be programmed into the QSPI flash
first. Then the booting will start from QSPI memory space.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from SD card to DDR, finally SPL transfer control to u-boot.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add SUPPORT_SPL feature for SD and NAND boot on
LS1021AQDS and LS1021ATWR.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
On LS1, DDR is initialized by reading SPD through I2C interface
in SPL code. For I2C, ll_entry_count() is called, and it returns
the number of elements of a linker-generated array placed into
subsection of .u_boot_list section specified by _list argument.
So add I2C linker list in the generic .lds to fix the issue about
using I2C in SPL.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The patch changes PCIe dts node status to 'disabled' if the
corresponding controller is disabled according to serdes protocol.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
After wakeup from deep sleep, Clear EPU registers as early as possible
to prevent from possible issue. It's also safe to clear at normal boot.
Signed-off-by: Chenhui Zhao <chenhui.zhao@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The bus frequency in SOC node should be clock frequency of platform.
That is not true if it is devided by 2.
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
R-Mobile and R-Car ARM SoCs use sh_mmcif as MMC host driver.
This adds arch-rmobile/mmc.h that defines mmcif_mmc_init().
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
stv0991 architecture support added. It contains the support for
following blocks
- Timer
- uart
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
[trini: Add arch/arm/cpu/armv7/Makefile hunk]
Signed-off-by: Tom Rini <trini@ti.com>
Some UniPhier boards are equipped with an expansion slot that
some optional SRAM/NOR-flash cards can be attached to. So, run-time
detection of the number of flash banks would be more user-friendly.
Until this commit, UniPhier boards have achieved this by (ab)using
board_flash_wp_on() because the boot failed if flash_size got zero.
Fortunately, this problem was solved by commit 70879a9256 (flash:
do not fail even if flash_size is zero).
Now it is possible to throw away such a tricky workaround. This
commit also enables CONFIG_SYS_MAX_FLASH_BANKS_DETECT for further
refactoring.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The macro __iomem is defined in include/linux/compiler.h.
Let's include it rather than double __iomem defines.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Introduce a Makefile under arch/$ARCH/ and include it in the
top Makefile (similar to Linux kernel). This allows further
refactoringi like moving architecture-specific code out of global
makefiles, deprecating config variables (CPU, CPUDIR, SOC) or
deprecating arch/$ARCH/config.mk.
In contrary to Linux kernel, U-Boot defines the ARCH variable by
Kconfig, thus the arch Makefile can only included conditionally
after the top config.mk.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This board sprinkles #ifdef(CONFIG_HERMES) over various global files
such as include/common.h, common/board_r.c, common/cmd_bdinfo.c.
Let's zap such an ill-behaved board.
It has not been converted to generic board yet and mpc8xx is old
enough.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
The U-Boot port runs on a variety of RPi models, not just the B. So,
rename the port to something slightly more generic.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Detect the board revision early during boot, and print the decoded
model name.
Eventually, this information can be used for tasks such as:
- Allowing/preventing USB device mode; some models have a USB device on-
board so only host mode makes sense. Others connect the SoC directly
to the USB connector, so device-mode might make sense.
- The on-board USB hub/Ethernet requires different GPIOs to enable it,
although luckily the default appears to be fine so far.
- The compute module contains an on-board eMMC device, so we could store
the environment there. Other models use an SD card and so don't support
saving the environment (unless we store it in a file on the FAT boot
partition...)
Set $fdtfile based on this information. At present, the mainline Linux
kernel doesn't contain a separate DTB for most models, but I hope that
will change soon.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Some configurations have been moved to Kconfig and the difference
among the config headers of UniPhier SoC variants is getting smaller
and smaller. Now is a good time to merge them into a single file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
There are two kinds of expansion boards which are often used for
the UniPhier platform and they are only exclusively selectable.
It can be better described by the "choice" menu of Kconfig.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
This ugly work-around code is unnecessary since commit f09eb52b3f
(mtd: denali: set some registers after nand_scan_ident()).
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Correctly increment the base address of the freeze controller. And since
SYSMGR_FRZCTRL_VIOCTRL_SHIFT is not needed, remove it from the include file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
socfpga_scan_manager structure was missing a data member.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
As suggested by Pavel, lets combine the two calls into one.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Without this alias, DM based probing does not work. So lets add this
alias to get the bus numbering correct for the Designware SPI
controllers.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Without this alias, DM based probing does not work. So lets add this
alias to get the bus numbering correct.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This DT node is taken from the Rocketboard.org Linux repsitory. And
is needed to enable (configure) the Cadence DM SPI driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The socfpga dts files are copied from the Rocketboards.org repository.
In U-Boot we usually replace the full-blown license header text with
the SPDX license identifiers. Lets do this for these new dts files
as well.
I just forgot to do this while adding the DT support for socfpga.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Newer qoriq socs have an updated dma ip block with a
different compatible. Let's make sure we use the proper
string so that the dmas get their liodn.
In order to have the means to specify the compatible
string, the liodn setting macros were updated to receive
a new parameter for it.
The following SoCs were changed to use the new compatible:
T1023/4, T1040, T2080/1, T4240, B4860.
Signed-off-by: Laurentiu Tudor <Laurentiu.Tudor@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Increase IO drive strength to fix FCS error on RGMII ports
on T1024QDS.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
fm_standard_init() initializes each 10G port by FM_TGEC_INFO_INITIALIZER.
but it needs different implementation of FM_TGEC_INFO_INITIALIZER on different SoCs.
on SoCs earlier(e.g. T4240, T2080), the notation between 10GEC and MAC as below:
10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2
on SoCs later(e.g. T1024, etc), the notation between 10GEC and MAC as below:
10GEC1->MAC1, 10GEC2->MAC2
so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to fit the new SoCs on
which 10GEC enumeration is consistent with MAC enumeration.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.
T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
T1024QDS is a high-performance computing evaluation, development and
test platform for T1024 QorIQ Power Architecture processor.
T1024QDS board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
prioritization and bandwidth allocation
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
- Two 10M/100M/1G RGMII ports on-board
- Three 1G/2.5Gbps SGMII ports
- Four 1Gbps QSGMII ports
- one 10Gbps XFI or 10Base-KR interface
- SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora
- PCIe: Three PCI Express controllers with five PCIe slots.
- IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA
- Video: DIU supports video up to 1280x1024x32 bpp.
- Chrontel CH7201 for HDMI connection.
- TI DS90C387R for direct LCD connection.
- Raw (not encoded) video connector for testing or other encoders.
- QUICC Engine block
- 32-bit RISC controller for flexible support of the communications peripherals
- Serial DMA channel for receive and transmit on all serial channels
- Two universal communication controllers, supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- eSPI: Three SPI flash devices.
- SATA: one SATA 2.O.
- USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB)
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC.
- I2C: Four I2C controllers.
- UART: Two UART on board.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>
Add support for Freescale T1024/T1023 SoC.
The T1024 SoC includes the following function and features:
- Two 64-bit Power architecture e5500 cores, up to 1.4GHz
- private 256KB L2 cache each core and shared 256KB CoreNet platform cache (CPC)
- 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support
- Data Path Acceleration Architecture (DPAA) incorporating acceleration
- Four MAC for 1G/2.5G/10G network interfaces (RGMII, SGMII, QSGMII, XFI)
- High-speed peripheral interfaces
- Three PCI Express 2.0 controllers
- Additional peripheral interfaces
- One SATA 2.0 controller
- Two USB 2.0 controllers with integrated PHY
- Enhanced secure digital host controller (SD/eSDHC/eMMC)
- Enhanced serial peripheral interface (eSPI)
- Four I2C controllers
- Four 2-pin UARTs or two 4-pin UARTs
- Integrated Flash Controller supporting NAND and NOR flash
- Two 8-channel DMA engines
- Multicore programmable interrupt controller (PIC)
- LCD interface (DIU) with 12 bit dual data rate
- QUICC Engine block supporting TDM, HDLC, and UART
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- Support for hardware virtualization and partitioning enforcement
- QorIQ Platform's Trust Architecture 2.0
Differences between T1024 and T1023:
Feature T1024 T1023
QUICC Engine: yes no
DIU: yes no
Deep Sleep: yes no
I2C controller: 4 3
DDR: 64-bit 32-bit
IFC: 32-bit 28-bit
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.
A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.
So put errata number and make it conditional.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.
Workaround is already in-place.
Put the errata number to adhere errata handling framework.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T2080 rev 1.1 changes MEM_RAT in RCW, which requires new parsing for ratio,
the same way as T4240 rev 2.0.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Re-map NAND&I2C boot-device to the "normal" NAND boot-device.
Otherwise the SPL boot IF can't handle this device correctly.
Somehow booting with Hynix 4GBit NAND H27U4G8 on Siemens
Draco leads to this boot-device passed to SPL from the BootROM.
With this change, Draco boots just fine into main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
The infomation of module control register for R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794) are almost the same, they can be combined into one
structure. This provides structure that summarizes infomation of module control
register and default register values.
And this structure is the module control use of the kernel at boot time.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This adds infomation of bits for module control register. This is used
to control modules on ARM R-Car SoCs.
Signed-off-by: Hisashi Nakamura <hisashi.nakamura.ak@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This addes macro for set and clear bit control for module control register.
This is used when user want to disable the function of the devices
corresponding to register.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Control macro of mstp is common in R-Car ARM SoC (r8a7790, r8a7791,
r8a7793 and r8a7794). This moves these to arch-rmobile/rcar-mstp.h
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Module control registers of R-Car ARM SoC (r8a7790, r8a7791, r8a7793 and
r8a7794) are same address. This moves these to header file of SoC.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
BeagleBoard-X15 is the next generation Open Source
Hardware BeagleBoard based on TI's AM5728 SoC
featuring dual core 1.5GHZ A15 processor. The
platform features 2GB DDR3L (w/dual 32bit busses),
eSATA, 3 USB3.0 ports, integrated HDMI (1920x108@60),
separate LCD port, video In port, 4GB eMMC, uSD,
Analog audio in/out, dual 1G Ethernet.
For more information, refer to:
http://www.elinux.org/Beagleboard:BeagleBoard-X15
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
expose those two definitions so they can be
used by another board which we're adding in upcoming
patches.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
this will allow for boards to overwrite those
in case memory setup is different.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
If we want to have two sections, one on each EMIF, without
interleaving, current code wouldn't enable emif2. Fix that
problem.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
some boards might want to use USB1 for host,
without fiddling those registers it'll be
impossible.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
Those regulators don't have any coupling with
what they supply, so remove the suffixes in order
to not confuse anybody.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
As checkpatch complaines about these camel-case defines, lets change
them to only use upper-case characters.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
- fix crash when sata device is not initialized
- remove disable_sata_clock() since it is not clear which clock for which
device should be disabled here
- call disable_sata_clock() for mx6 in preboot_os instead
Signed-off-by: Soeren Moch <smoch@web.de>
Acked-by: Nikita Kiryanov <nikita@compulab.co.il>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
If CONFIG_OF_CONTROL is defined, search device tree nodes that are
compatible with "panasonic,uniphier-ehci" and take the base address
from their "reg" property.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OF_CONTROL is enabled, lib/fdtdec.c is compiled.
It includes <asm/gpio.h> and then <asm/gpio.h> includes
<asm/arch/gpio.h>. Consequently, all the SoCs that enable
CONFIG_OF_CONTROL must have <asm/arch/gpio.h> even if they do not
support GPIO.
In the first place, GPIO has nothing to do with OF_CONTROL.
It is wrong that lib/fdtdec.c includes GPIO functions; it should
be split into two files, FDT-common things and GPIO things.
It is, however, a pretty big work to fix that correctly.
This is a compromised commit to add a dummy <asm/arch/gpio.h>
to support OF_CONTROL for UniPhier platform. This dummy header
will be removed after FDT-GPIO stuff is fixed correctly.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The initramfs is currently only relocated if the user calls
the bootm ramdisk subcommand. If bootm should be used without
subcommands, the arch-specific bootm code needs to implement
the relocation.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
After all MIPS boards are switched to generic-board, the
MIPS specific board.c can be removed.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
To get correct stack walking and backtrace functionality in gdb,
registers fp and ra should be initialized before calling board_init_f
or board_init_r. Thus allocating stack space and zeroing it as it is
currently done in board.c becomes obsolete.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
This fixes the following two problems:
cppcheck reports:
[arch/sandbox/cpu/start.c:132]: (error) Uninitialized variable: err
[arch/sandbox/cpu/os.c:371]: (error) Memory leak: fname
Signed-off-by: Simon Glass <sjg@chromium.org>
Reported-by: Wolfgang Denk <wd@denx.de>
Intel's Graphics Media Accelerator (GMA) is a generic name for a wide range
of video devices. Add code to set up the hardware on ivybridge. Part of the
init happens in native code, part of it happens in a 16-bit option ROM for
those nostalgic for the 1970s.
Signed-off-by: Simon Glass <sjg@chromium.org>
On x86 machines we can use an emulator to run option ROMS as with other
architectures. But with some additional effort (mostly due to the 16-bit
nature of option ROMs) we can run them natively. Add support for this.
Signed-off-by: Simon Glass <sjg@chromium.org>
