Move CONFIG_CSF_SIZE to Kconfig and define default value as 0x4000.
mx8mqevk requires 0x2000 add this configuration in imx8mq_evk_defconfig
file.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Currently the SPL binary is 67 kB, which leaves only 1 kB of free
internal RAM space.
The following options can be safely removed to save some precious
SPL space:
- CONFIG_SPL_FS_EXT4: u-boot-dtb.img is stored in raw sector via dd
command (at offset 69 kB)
- CONFIG_SPL_I2C_SUPPORT: I2C is not used during SPL
- CONFIG_SPL_OS_BOOT: no need to make Falcon mode supported
by default
After this change the SPL binary size gets down to 51 kB.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP B0, there is change in NIC clock dividers architecture.
On A0, the NIC1 BUS and EXT dividers were in a chain with NIC1 DIV, but
on B0 they are parallel with NIC1 DIV. So now the dividers are independent.
This patch modifies the scg_nic_get_rate function according to this change.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
The normal target frequency for ULP A7 core is 500Mhz, but now ROM
set the core frequency to 413Mhz. So change it to 500Mhz in u-boot.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The GPU uses APLL PFD2 as its clock parent (483.84Mhz) with divider
set to 1. This frequecy is out of ULP A0 spec. The MAX rate for GPU
is 350Mhz. So we simply configure the APLL PFD2 to 345.6Mhz (FRAC=28)
to workaround the problem. The correct fix should let GPU handle the
clock rate in kernel.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The num/denom is a float value, but in the calculation it is convert
to integer 0, and cause the result wrong.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Wrong I2c driver configuration name is used in codes, so I2c driver is
not built. Correct it.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since many drivers need this CONFIG_MX7ULP to distiguish the settings
for i.MX7ULP only. Add this entry to cpu's kconfig.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The offset for FRAC and the mask for PCD are not correct.
If we set FRAC, we can't get the right frequency. Fix them
to correct value.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On i.MX7ULP, value zero is reserved in SCG1 RCCR register,
so the val should be decreased by 1 to get the correct clock
source index.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The board will reboot if A7 core enter mem mode by rtc, then M4 core
enter VLLS mode after the RTC alarm expired. Enable the dumb PMIC mode
to fix this issue.
Since i.MX7ULP B0 moves the SNVS LP into M4 domain, A core can't access
it. So check the CPU rev and not apply the settings for B0.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the SD3.0 kernel driver needs M4 image support, this causes
problem for usb boot booting into kernel. To decouple the relationship,
we modify the FDT file in u-boot to disable SD3.0.
So the kernel won't depend on M4 image.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add CONFIG_DM_GPIO to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This is in preparation for adding CONFIG_DM_SPI.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
This prevents messages like
gpio@20a0000: get_value: error: gpio GPIO2_2 not reserved
when CONFIG_DM_GPIO is enabled.
Also, when CONFIG_DM_GPIO is enabled, checkboard is too
early to use gpio_get_value, so read it directly on failure.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Add DM_MMC to all defconfigs whose board is
nitrogen6x.
mx6qsabrelite_defconfig
nitrogen6dl2g_defconfig
nitrogen6dl_defconfig
nitrogen6q2g_defconfig
nitrogen6q_defconfig
nitrogen6s1g_defconfig
This commit is adding multiple configs, but
seems to be the minimum change to not lose features
and still compile fine.
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Previously the SPL size on all iMX6 platforms was restricted to 68KB
because the OCRAM size on iMX6SL/DL parts is only 128KB. However, the
other iMX6 variants have 256KB of OCRAM. Add an option
CONFIG_MX6_OCRAM_256KB which allows using the full size on boards which
don't need to support the SL/DL variants. This allows for an SPL size of
196KB, which makes it much easier to use configurations such as SPL with
driver model and FDT control.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Tested-by: Adam Ford <aford173@gmail.com> #imx6q_logic
There is no need to use HAB for FIT signature validation when
SPL_FIT_SIGNATURE is also enabled, as that will be validated via the
normal U-Boot signed FIT image flow.
This allows having SPL validated by HAB and the payloads to follow
being validated with FIT signatures only.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Toradex Apalis iMX6 modules are available in the iMX6D and iMX6Q
variants, which are quite similar and already managed via only one
dtb in u-boot (imx6-apalis.dtb). Select MX6Q via Kconfig by default in
order to automatically enable the HAS_CAAM and MX6_SMP features.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
Only one dtb is currently supported, so match with imx6-apalis.
Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Pass spl_image and bootdev to board_return_bootrom.
i.MX8MN needs the args to let ROM to load images
Cc: Simon Glass <sjg@chromium.org>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
i.MX7 and i.MX8M use mxc uart driver, so let's make the SoC could
use MXC_UART kconfig.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Add missed break for HDMI entry.
And moving FIT parsing earlier, because it does not have parameter,
it will not runs into CFG_REG_SIZE.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
fdtdec_get_addr_size could not parse addr/size correctly is
using address-cells 2 and size-cells 2 on an ARM32 SoC.
So switch to use devfdt_get_addr_size_index.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To support DM_VIDEO,
Add display node for lcdif
Drop board iomuxc settings.
Enable DM_VIDEO
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
When booting SPL on the board, met boot failure:
"
Trying to boot from MMC2
MMC Device 1 not found
spl: could not find mmc device 1. error: -19
SPL: failed to boot from all boot devices
"
Let's register the two mmc controllers in SPL stage to
avoid boot failure.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ board support. the i.MX6ULZ is SW compatible
with i.MX6ULL. so most code of i.MX6ULL can be reused
by i.MX6ULZ.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add i.MX6ULZ cpu type and helper.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Import kernel dts for i.MX6ULZ from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6ULL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Sync kernel dts for i.MX6UL from
commit <0a8ad0ffa4d8> ("Merge tag 'for-linus-5.3-ofs1' of git://git.kernel.org/pub/scm/linux/kernel/git/hubcap/linux")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
The commit
642b80d256 ("net: designware: drop compatible altr, socfpga-stmmac")
breaks designware ethernet for all ARC boards. It removes
"altr, socfpga-stmmac" compatible from "drivers/net/designware.c"
without changing compatible in the boards which use it.
Fix that by adding "snps,arc-dwmac-3.70a" compatible string to
"drivers/net/designware.c" and using it in ARC boards device tree.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes: 8f994c860d ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
These boards don't have a watchdog enabled in SPL, so make sure
CONFIG_SPL_WDT is not enabled.
Fixes: commit 6874cb7220 ("watchdog: Split WDT from SPL_WDT")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Assorted TI platform fixes
- Revert the change that broke environment flag validation
- Assorted typo fixes
- Assorted Kconfig dependency fixes
- Other minor bug fixes
This reverts commit 7d4776545b. The
changes here break environment validation and furthermore do not seem to
be required.
Signed-off-by: Tom Rini <trini@konsulko.com>
