Convert pico-imx7d to SPL support.
There are two variants of pico-imx7d SOMs:
- One with 512MB of RAM
- One with 1GB of RAM
The 512MB module contains two Hynix H5TC2G63GFR-PBA.
The 1GB module contains two Hynix H5TC4G63GFR-PBA.
The RAM size is determined in runtime by reading GPIO1_12.
While at it, also add USB Serial Download mode support as it
is very helpful for loading SPL and u-boot.img via imx_usb_loader.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
fastboot tool is a convenient way to flash the eMMC, so
add support for it.
Examples of usages:
On the pico-imx7d U-Boot prompt:
=> fastboot 0
On the Linux PC connected via USB:
1. Retrieving the U-Boot version
$ sudo fastboot getvar bootloader-version -i 0x0525
bootloader-version: U-Boot 2018.07-rc1-03888-gde846f9
finished. total time: 0.000s
2. Resetting the board
$ sudo fastboot reboot -i 0x0525
(this causes the pico-imx7d to reboot)
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This allow the use of:
> run setup_emmc
inside of the U-Boot prompt to do the partitioning of the disk.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
This sets DISTRO_CONFIG and BOOTCOMMAND, as well as add a `finduuid`
environment helper to allow it to properly work with Yocto Project and
other distributions using extlinux autogenerated configuration files.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Instead of keeping a custom environment, use a more generic approach
by switching to disto config.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Previously we had stored the environment right after the
u-boot.img on the disk. I never liked this because with dtbs
being included and such the image could grow in size. Instead
we move the environment to be negatively offset from the 1MB
mark. Almost all our images start at 4MB's, and most standard
images start at 1MB, and all our storage devices are a minimum
1MB. Therefore we can store env there for all classes of devices
and have plenty of space in case u-boot.img needs to grow.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Mainline and now the SolidRun 4.9 nxp based tree use the new
reorganization of device-tree files that separate out the emmc
into its own dtb. u-boot will now look for -emmc in the device
tree name if one is detected.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
The IN_PROGRESS macro has been removed in commit bd47c13583 (mmc: Fix
splitting device initialization). Remove it from the mmc_start_init()
function description.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
The DA850-EVM and OMAPL138_LCDK both use checks for CONFIG_USE_NAND.
This patch changes these checks to CONFIG_NAND which is already defined
in Kconfig. Since the OMAPL138_LCDK already had CONFIG_NAND defined in its
defconfig, it can be deleted from configs/omapl138_lcdk.h.
Signed-off-by: Adam Ford <aford173@gmail.com>
Currently the fdtfile environment variable is set to
CONFIG_DEFAULT_DEVICE_TREE which is іnternally used as U-Boot devicetree
source. The OS can use a different filename and Kconfig gives us the
ability to select a default devicetree via CONFIG_DEFAULT_FDT_FILE.
This also gives user configuring U-Boot via menuconfig the behaviour
someone would expect.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Tested-By: Vagrant Cascadian <vagrant@debian.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The first dhcp command consistently fails with a timeout when
the lion-rk3368 board is connected to a Zyxel GS1100-24E
Gigabit Ethernet switch:
ethernet@ff290000 Waiting for PHY auto negotiation to complete......... TIMEOUT !
Increasing PHY_ANEG_TIMEOUT from the default 4000 to 8000 makes the
first dhcp command work reliably.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
On some boards, we want to give the board/architecture-specific code a
chance to look at where the next image has been loaded from and
perform fixups before starting the next image. This is of particular
importance, when we probe multiple devices for bootable payloads and
boot the first one found.
This change adds the following:
- we record the boot_device used into the spl_image structure
- we provide an extension-point for boards/architectures that can
perform late fixups depending on a fully populated spl_image
structure (i.e. we'll know the final boot_device and have info
on the image type and operating system to be booted).
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The test for (CONFIG_BOOTDELAY >= 0) has been in U-Boot since the
beginning, but the meaning of it has changed over time. Allow the
default to be set for any value, including -ve ones. This allows
(for example) CONFIG_ENV_IS_NOWHERE to have values for bootdelay in
its compiled in environment.
The only thing this changes is where the default for bootdelay can be
fetched from; before this change you get a compiled in default, after
you'll pull it from the default value in the environment, but both values
will be the same. Also if there's a value set in the environment then
that will take precedence (as before).
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
- add a devicetree for each variant (mmc, spi, nand)
- drop unneeded code from board and bur/common
- drop unneeded stuff from config header files
- minor adaptions to be compliant with driver model (requesting gpio,..)
- harmonize the commandset over all brppt1 targets
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
With this commit we do:
- set the bootdelay in all brppt1 defconfigs to 0, this makes
development easier, since we can break into serial console.
- move CONFIG_BOOTCOMMAND from header file to defconfig
- introduce b_mode variable for selecting the final boot-target.
This b_mode represents the boot-switch, which can found on most b&r
targets. On the brppt1 this boot-switch is derived from some gpio and
the bootcounter within the RTC block, making it so possible to force
a boot-target (as example for repair-case).
- refactor the environment for booting new flexible way
primary we want to get some bootscr.img within the mass-storage,
this script then loads everything needed for the boot.
For legacy reason we implement the t30lgcy#x boot targets, booting the
already delivered linux-images.
- make space for the cfgscr within mtdparts on brppt1_nand
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
The falcon mode was never used on this board, there is also no plan to
use it. So drop this dead code.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
On this linux target long time ago the OS is using DRM driver for
handling video output, the pre initialization of u-boot and the display
summary screen is obsolete. With this patch we drop the LCD-support from
thisd board.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This patch drops the lcd-screen setup, the summary screen and getting
mac-addresses based on a previous loaded device-tree for linux targets.
Selecting those linux target is simple, since we have only the brppt1.
In detail we do:
- drop the common lcd-setup code which relys on a fdt_blob
- drop the common dtb loading mechanism
- drop the now obsolete CONFIG_USE_FDT from board header and whitelist.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.
This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller
Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The function set_default_env() sets the hashtable flags for import_r().
Formally set_default_env() doesn't accept flags from its callers. In
practice the caller can (un)set the H_INTERACTIVE flag, but it has to be
done using the first character of the function's string argument. Other
flags like H_FORCE can't be set by the caller.
Change the function to accept flags argument. The benefits are:
1. The caller will have to explicitly set the H_INTERACTIVE flag,
instead of un-setting it using a special char in a string.
2. Add the ability to propagate flags from the caller to himport(),
especially the H_FORCE flag from do_env_default() in nvedit.c that
currently gets ignored for "env default -a -f" commands.
3. Flags and messages will not be coupled together. A caller will be
able to set flags without passing a string and vice versa.
Please note:
The propagation of H_FORCE from do_env_default() does not introduce any
functional changes, because currently himport_r() is set to destroy the
old environment regardless if H_FORCE flag is set or not. More changes
are needed to utilize the propagation of H_FORCE.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
The env_flag in do_env_default() doesn't get propagated and therefore
gets ignored by himport_r(). This breaks to ability to "forcibly" reset
variables to their default values using the environment command.
Scenario example of the problem:
# setenv kernel uImage
# setenv .flags kernel:so
# env default -f kernel
## Error: Can't overwrite "kernel"
himport_r: can't insert "kernel=zImage" into hash table
Change the call path so it will pass the flag correctly.
Signed-off-by: Yaniv Levinsky <yaniv.levinsky@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Add ut_assertnull macro to include/test/ut.h
For testing of functions that returns NULL on errors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Mini targets are using different ENV_SIZE then standard one that's why
defconfigs should be updated to simplify config files.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add configuration files/dtses for mini u-boot configuration
which runs on smaller footprint of internal memory. This
configuration has only required qspi flash support and it
uses DCC as serial.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch added support to enable CONFIG_ENV_SIZE, CONFIG_ENV_OFFSET
and CONFIG_ENV_SECT_SIZE through Kconfig for Zynq and Zynqmp.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove the SDRAM_BASE and SDRAM_SIZE as it can now get these
details from DT.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch renames the routine fdtdec_setup_memory_size()
to fdtdec_setup_mem_size_base() as it now fills the
mem base as well along with size.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
XILINX_SPI_FLASH_BASEADDR logic has been converted to DM that's why
there is no reason to depend on this address anymore.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
These macros are not required anymore. These will be taken from
configuration file.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
There is no reason to define default option for this macro which is
already done in common/cli_hush.c.
86 #ifndef CONFIG_SYS_PROMPT_HUSH_PS2
87 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
88 #endif
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: York Sun <york.sun@nxp.com>
command_ret_t enum contains 3 return values but only two are handled
now. Extend cmd_process_error() and handle CMD_RET_USAGE separately.
These commands are affected by this change.
cmd/demo.c
cmd/efi.c
cmd/gpio.c
cmd/qfw.c
cmd/x86/fsp.c
test/dm/cmd_dm.c
And scripts shouldn't be affected because return value is not 0. But
every command implementation can choose what it is correct to pass.
I would expect that RET_USAGE is called when parameters are not
correctly passed (have incorrect value, missing parameters)
and RET_FAILURE when correct parameters are passed but command fails.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
Update the device tree files from the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit 55c5ba5e49a0a124ed416880e8227b493474495e
Author: Chen-Yu Tsai <wens@csie.org>
Date: Tue Apr 24 19:34:22 2018 +0800
arm64: dts: allwinner: h5: Add cpu0 label for first cpu
Since the H3 and H5 are very similar (aside from the actual ARM cores),
they share most the SoC .dtsi and thus have to be updated together.
One tiny change is the removal of the "arm/" prefix from the include
path in the sun50i-h5.dtsi, which is needed because we don't share the
same sophisticated DT directory layout of Linux.
Also we need to fix up the board .dts files already, since the .dtsi
removes some pins, so the .dts can't reference them anymore. This is to
maintain bisectability.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Updates the device tree file from the the Linux tree as of v4.18-rc3,
exactly Linux commit:
commit c1cff65f9b16b31e731e2e75bbe06638c86e1996
Author: Harald Geyer <harald@ccbib.org>
Date: Thu Mar 15 16:25:08 2018 +0000
arm64: dts: allwinner: a64: add simplefb for A64 SoC
This also pulls in the newly required include files for the clock and
reset bindings, also removes the now redundant part from our
*-u-boot.dtsi overlay file.
I kept the PWM node from U-Boot, as we recently gained this explicitly
for U-Boot's own usage and I don't want to regress here. This node is in
the queue for mainline Linux already, so the next sync will make it all
equal again.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add build support for Stratix SoC
Signed-off-by: Chin Liang See <chin.liang.see@intel.com>
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Conflicts:
arch/arm/Kconfig
arch/arm/mach-socfpga/Kconfig
When generating timestamps in signatures, use imagetool_get_source_date()
so we can be overridden by SOURCE_DATE_EPOCH to generate reproducible
images.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Reviewed-by: Simon Glass <sjg@chromum.org>
Newer kernels have moved from ttyO0 to ttyS0, and when booting
it drops a notice:
WARNING: Your 'console=ttyO0' has been replaced by 'ttyS0'
This ensures that you still see kernel messages. Please
update your kernel commandline.
This patch updates the console to use ttyS0 and eliminate the
chatter.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Change to use CONFIG_IS_ENABLED(DM_RESET), so this can work in SPL
build (CONFIG_SPL_DM_RESET) and U-boot build (CONFIG_DM_RESET).
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds uCRobotics Bubblegum-96 board support. This board is
one of the 96Boards Consumer Edition platform based on Actions Semi
S900 SoC.
Features:
- Actions Semi S900 SoC (4xCortex A53, Power VR G6230 GPU)
- 2GiB RAM
- 8GiB eMMC, uSD slot
- WiFi, Bluetooth and GPS module
- 2x Host, 1x Device USB port
- HDMI
- 20-pin low speed and 40-pin high speed expanders, 6 LED, 3 buttons
U-Boot will be loaded by ATF at EL2 execution level. Relevant driver
support will be added in further commits.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Add a way to decode a memory region, including the memory type (sram or
sdram) and its start address and size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new device_bind_ofnode() function which can bind a device given its
ofnode. This allows binding devices more easily with livetree nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is sometimes useful to show a message when logging an error return
value, perhaps to add a few details about the problem. Add a function to
support this.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a 32-bit version of this function. Add a 64-bit version as well so
we can easily read 64-bit ints from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Support a default memory bank, specified in reg, as well as
board-specific memory banks in subtree board-id nodes.
This allows memory information to be provided in the device tree,
rather than hard-coded in, which will make it simpler to handle
similar devices with different memory banks, as the board-id values
or masks can be used to match devices.
Signed-off-by: Michael Pratt <mpratt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Vadim Bendebury <vbendeb@chromium.org>
The various Aries Embedded boards have been orphaned for a year and no
one has come forward to take care of them. Remove.
Signed-off-by: Tom Rini <trini@konsulko.com>
The ax25-ae350 target currently uses CONFIG_BOOTP_SERVERIP which means we
ignore the DHCP provided TFTP ip address. This breaks every case where we
do now provide a serverip environment variable.
Instead, let's use the new CONFIG_BOOT_PREFER_SERVERIP option to fall back
to the DHCP provided TFTP IP if no serverip environment variable is set.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Rick Chen <rick@andestech.com>
We can call commands like dhcp and bootp without arguments or with
explicit command line arguments that really should tell the code where
to look for files instead.
Unfortunately, the current code simply overwrites command line arguments
in the dhcp case with dhcp values.
This patch allows the code to preserve the command line values if they
were set on the command line. That way the semantics are slightly more
intuitive.
The reason this patch does that by introducing a new variable is that we
can not rely on net_boot_file_name[0] being unset, as today it's
completely legal to call "dhcp" and afterwards run "tftp" and expect the
latter to repeat the same query as before. I would prefer not to break
that behavior in case anyone relies on it.
Signed-off-by: Alexander Graf <agraf@suse.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add a new command 'wol': Wait for an incoming Wake-on-LAN packet or
time out if no WoL packed is received.
If the WoL packet contains a password, it is saved in the environment
variable 'wolpassword' using the etherwake format (dot or colon
separated decimals).
Intended use case: a networked device should boot an alternate image.
It's attached to a network on a client site, modifying the DHCP server
configuration or setup of a tftp server is not allowed.
After power on the device waits a few seconds for a WoL packet. If a
packet is received, the device boots the alternate image. Otherwise
it boots the default image.
This method is a simple way to interact with a system via network even
if only the MAC address is known. Tools to send WoL packets are
available on all common platforms.
Some Ethernet drivers seem to pad the incoming packet. The additional
padding bytes might be recognized as Wake-on-LAN password bytes.
By default enabled in pengwyn_defconfig.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ACPI tables can be passed via EFI configuration table to an EFI
application. This is only supported on x86 so far.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
`nand_get_flash_type()` allows identification of supported NAND flashs.
The function is useful in SPL (like mxs_nand_spl.c) to lookup for a NAND
flash (which does not support ONFi) instead of using nand_simple.c and
hard-coding all required NAND parameters.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The PFUZE3000 uses registers addresses up to 0xff.
The DM pfuze100 driver supports both pfuze100 and pfuze3000. Allow it
to use the device type to return the correct number of registers.
Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Currently efi.h determines a few bits of its environment according to
config options. This falls apart with the efi stub support which may
result in efi.h getting pulled into the stub as well as real U-Boot
code. In that case, one may be 32bit while the other one is 64bit.
This patch changes the conditionals to use compiler provided defines
instead. That way we always adhere to the build environment we're in
and the definitions adjust automatically.
Signed-off-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: added some comments to describe the __x86_64__ check]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
For boards that don't route serial port pins out, it's quite common
to attach a USB keyboard as the input device, along with a monitor.
However USB is not automatically started in the generic efi payload
codes. This uses a payload specific last_stage_init() to start the
USB bus, so that a USB keyboard can be used on the U-Boot shell.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
BOOT2 partition is empty and free for using to store the environment.
Use that instead of the default user partition.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
cpu_cmd() is reading cpu number via simple_strtoul() which is always
unsigned type.
Platform code implementations are not expecting that nr can be negative
and there is not checking in the code for that too.
This patch is using u32 type for cpu number to make sure that platform
code get proper value range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add option to the booti_setup() which indicates to it that the caller
requires the image to be relocated to the beginning of the RAM and
that the information whether the image can be located anywhere in RAM
at 2 MiB aligned boundary or not is to be ignored. This is useful ie.
in case the Image is wrapped in another envelope, ie. fitImage and not
relocating it but moving it would corrupt the envelope.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Bin Chen <bin.chen@linaro.org>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-By: Bin Chen <bin.chen@linaro.org>
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d0 ("block: Have BLOCK_CACHE default to y in some cases")
Signed-off-by: Adam Ford <aford173@gmail.com>
Don't continue updating the offset when buffer is full.
When the buffer size exhausts and there's no space left to write
warn the user and update only the needed size and not both the
offset and needed size.
Add needed buffer size information in the iotrace command.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The header definitions are needed for reading
record information in cmd/iotrace.c
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove empty #ifdef/#ifndef..#endif blocks where the configuration they
guarded has been completely removed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
1. Add vbmeta partition info to android partition layout for TI
platforms.
2. Add support of AVB 2.0 (including avb subset of commands) for am57xx HS
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
[trini: Move to include/environment/ti/boot.h, reword commit slightly]
Signed-off-by: Tom Rini <trini@konsulko.com>
1. Add initial support of boot states mode (red, green, yellow)
2. Add functions for enforcing dm-verity configurations
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Implement AVB ops on top of existing mmc subsystem API. Currently there
is a full implementation of such operations, defined by [1]
AVB2.0 specification:
.read_from_partition() - reads N bytes from a partition identified by
a name.
.write_to_partition() - Writes N bytes to a partition identified by a name.
.validate_vbmeta_public_key() - checks if the given public ‘vbmeta’
partition is trusted.
.get_unique_guid_for_partition() - Gets the GUID for a partition identified
by a string name.
As [1] specification recommends to use tamper-evident storage for storing
rollback indexes and device state (LOCKED/UNLOCKED),
currently are only stubs instead of full implementation for these ops:
.read_rollback_index() - Gets the rollback index for a given index location
.write_rollback_index() - Sets the rollback index to a given location
.read_is_device_unlocked() - Gets where the device is unlocked
[1] https://android.googlesource.com/platform/external/avb/+/master/README.md
Signed-off-by: Igor Opaniuk <igor.opaniuk@linaro.org>
In order to properly detect the board the checks need to be done
in a specific order. Move these tests back into a single enum
function that will always return the proper the board it is checking.
This also adds the best test we have for detecting the rev 1.5 som,
and it simplifies the device-tree filename building.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Since kernel commit 41bbeadceb03 ("ARM: dts: imx7d-pico-pi: Separate
into cpu and baseboard dts") the dtb name has changed.
Fix it accordingly.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
We should use the baudrate variable available inside U-Boot
environment to allow it to be changed dynamically.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
If GPT gets broken, then after N boot attempts we will run the SWUpdate
restoration image.
On its enter we will check GPT and restore it if needed.
To test it:
display5 > mmc write 0x12000000 4 8
It will overwrite the primary GPT table.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After splitting rootfs images to BACKUP and ACTIVE, the "factory"
u-boot also needs to update the former.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Test case:
The fitImage gets corrupted:
truncate -c -s 3M fitImage
run tftp_mmc_fitImg
setenv boot_os y
reset
[board shall hang in SPL with
"Trying to boot from MMC1" information]
Then after X seconds WDT is causing board to reset. After N boot attempts
we enter recovery mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To enter the special mode, one needs to short cut two pads with e.g. screw
driver.
After power up the SPL will execute u-boot in which proper actions will be
taken.
It is worth noting that we do not alter envs (even the BOOT_FROM variable)
and unconditionally go to recovery.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The SPI-NOR partition information has been updated to store
swupdate-kernel-FIT just after envs as well as two times larger
swupdate-initramfs image.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This is a prerequisite patch to combine SWUpdate and Linux recovery
initramfs images.
It removes the support for it.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Since display5 is now supporting boot counting, we can just reset the
board when bootm fails (i.e. it doesn't boot the fitImage kernel for
any reason).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
It may be necessary to update the content of the whole SPI-NOR memory at
once with using a single command (tftp_sf_img).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To test if this partition is present - one needs to write:
display5 > sf probe; mtdparts
display5 > sf erase factory +0x100000
Signed-off-by: Lukasz Majewski <lukma@denx.de>
When BOOT_FROM = FACTORY, then the LEG's factory setup is performed.
This code relies on boot_nfs u-boot command, so it shall be adjusted
appropriately (e.g. provide proper fitImage file).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
To avoid confusion, let's rename the efi-x86 target to efi-x86_app.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If UEFI BIOS has the graphics output protocol (GOP), let's pass its
information to U-Boot payload so that U-Boot can utilize it (eg:
an EFI framebuffer driver).
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
It is possible to create a generic EFI payload for all x86 boards.
The payload is configured to include as many generic drivers as
possible. All stuff that touches low-level initialization are not
allowed as such is the EFI BIOS's responsibility. Platform specific
drivers (like gpio, spi, etc) are not included.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Here we just add a tool for HSDK flashable images preparation
together with extensive documentation for HSDK board.
This will help real-life users to update U-Boot on the board.
HSDK board has preloader that reads SPI flash pages and searches
for a special image header to fetch and load binary.
Add tool, make target (bsp-generate) to generate
update script and u-boot binary image with header for preloader.
Also add script to default environment to apply updates.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Point the $loadaddr variable and default load address to a more sane
area, 384 MiB from the start of RAM. This is to avoid all the reserved
memory at the beginning of RAM. The old behavior could still be easily
retained by "setenv loadaddr 0x48080000" . The new setup allows us to
use for example modern fitImage with kernel_noload, so use this as a
new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Point the $loadaddr variable and default load address to a more sane
area, 256 MiB from the start of RAM. While it is convenient to use
uImage without copying, which is why the previous load address was
set the way it was, uImage is now legacy. This behavior could still
be easily retained by "setenv loadaddr 0x40007fc0" . The new setup
allows us to use for example modern fitImage with kernel_noload, so
use this as a new preferred default.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The CONFIG_SYS_CLK_FREQ is not used on some of the Gen3 boards,
remove it. Moreover, on Ebisu this actually didn't match the
comment in the config file at all, but since it was not used,
there was no real problem.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
A few minor fixes for the release:
- Compile fixes
- HI20 relocations for RISC-V
- Fix bootefi without load path
- Fix Runtime Services with certain compilers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/PaA
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-06-14
A few minor fixes for the release:
- Compile fixes
- HI20 relocations for RISC-V
- Fix bootefi without load path
- Fix Runtime Services with certain compilers
Sync the gpio.h header with Linux 4.17, which contains new macros.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
When building with -pedantic the current definition of EFI_GUID() causes
an error 'initializer element is not constant'.
Currently EFI_GUID() is used both as an anonymous constant and as an
intializer. A conversion to efi_guid_t is not allowable when using
EFI_GUID() as an initializer. But it is needed when using it as an
anonymous constant.
We should not use EFI_GUID() for anything but an initializer. So let's
introduce a variable where needed and remove the conversion.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The PE standard allows for HI20/LOW12 relocations. Within the efi_loader
target we always know that our relocation target is 4k aligned, so we
don't need to worry about the LOW12 part.
This patch adds support for the respective relocations. With this and a
few grub patches I have cooking in parallel I'm able to run grub on RISC-V.
Signed-off-by: Alexander Graf <agraf@suse.de>
Add the new mode to indicate a built-in PHY.
This will be used by UniPhier AVE ethernet driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
VCAP tables must be initialized even if no advanced classification
is used. If no initialization is performed, then ECC error will
be observed by the user when the first packet enters the l2switch.
The error is marked in MPIC_EISR0 -bit 29 which means - Internal RAM
multi-bit ECC error.
This patch fixes the aforementioned ECC error by performing the
initialization of VCAP tables.
Signed-off-by: Radu Bulie <radu-andrei.bulie@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add support for Cortina CS4223 10G PHY
- As per the CS4223 specs, an EEPROM module is
connected to the PHY. At startup the PHY reads
the firmware line and tries to load the firmware
into the internal memory.
- This driver reads the EEPROM status
and checks if firmware has been loaded
Signed-off-by: Vicentiu Galanopulo <vicentiu.galanopulo@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
After the commit 265edc03d5 ("fs/fat: Clean up open-coded sector
<-> cluster conversions"), it is hung up writing new file to FAT16
disk with more than 19 files in armv7. It is because result value
of sect_to_cluster() is not proper by casting from signed value to
unsigned value. Fix the wrong casting of sect_to_cluster().
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
generic.h has changed in Linux and new addtionals functions were
added.
This commit takes the latest and greatest from Linux (v4.17-rc5)
to aid with porting drivers that utilize these functions.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
In upstream Linux kernel, the fdtfile
for this specific board is called am335x-wega-rdk.dtb
Signed-off-by: Matwey V. Kornilov <matwey.kornilov@gmail.com>
The helios4 is built on the SolidRun Armada 38x SOM.
The port os based on the ClearFog board, using information from
https://github.com/helios-4/u-boot-marvell as well as dtb input
from https://github.com/helios-4/linux-marvell
Signed-off-by: Dennis Gilmore <dennis@ausil.us>
Signed-off-by: Dennis Gilmore <dgilmore@redhat.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Added the following:
1. defconfig for LS1012AFRWY Secure boot
2. PfE Validation support
Signed-off-by: Vinitha V Pillai <vinitha.pillai@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
