Signed-off-by: Anton Staaf <robotboy@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Jason Jin <jason.jin@freescale.com>
Seems people fixed their files to use libfoo.o, but didn't actually
update the creation targets to use $(cmd_link_o_target). Update the
rest of the Makefile's found with grep.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Tested-by: Simon Glass <sjg@chromium.org>
There are several mdelay() definitions in the driver and
board code. Remove them all and provide a common mdelay()
in lib/time.c.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
SoC ag101 is the first chip using NDS32 N1213 cpu core.
Add header file of device offset support for SoC ag101.
Add main function of SoC ag101 based on NDS32 n1213 core.
Add lowlevel_init.S and other periphal related code.
This version of lowlevel_init.S also replace hardcode value
by MARCO defines from the GPL version andesboot for better
code quality.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Add N1213 cpu core (N12 Core family) support for NDS32 arch.
This patch includes start.S for the initialize procedure of N1213.
Start procedure:
start.S will start up the N1213 CPU core at first,
then jump to SoC dependent "lowlevel_init.S" and
"watchdog.S" to configure peripheral devices.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
Signed-off-by: Greentime Hu <greentime@andestech.com>
Add generic header files support for nds32 architecture.
Cache, ptregs, data type and other definitions are included.
Signed-off-by: Macpaul Lin <macpaul@andestech.com>
* 'master' of git://git.denx.de/u-boot-mpc85xx:
mpc85xx: Add inline GPIO acessor functions
powerpc/85xx: wait for alignment before resetting SERDES RX lanes (SERDES9)
powerpc/85xx: Fix P2020DS booting
powerpc/85xx: Update USB device tree status based on pin settings
fdt: Add new fdt_set_node_status & fdt_set_status_by_alias helpers
powerpc/85xx: Add support for RMan LIODN initialization
powerpc/85xx: Update device tree handling for SRIO
powerpc/85xx: Update setting of SRIO LIODNs
fm: Don't allow disabling of FM1-DTSEC1
fm-eth: Don't mark the MAC we use for MDIO as disabled in device tree
To ease the implementation of other MPC85xx board ports, several common
GPIO helpers are added to <asm/mpc85xx_gpio.h>.
Since each of these compiles to no more than 4-5 instructions it would
be very inefficient to call them out of line, therefore we put them
entirely in the header file.
The HWW-1U-1A board port which these were written for strongly prefers
to set multiple GPIOs as a single batch operation, so the API is
designed around that basis.
To assist other board ports, a small set of wrappers are used which
provides a standard gpio_request() interface around the MPC85xx-specific
functions. This can be enabled with CONFIG_MPC85XX_GENERIC_GPIO
Signed-off-by: Kyle Moffett <Kyle.D.Moffett@boeing.com>
Cc: Andy Fleming <afleming@gmail.com>
Cc: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The work-around for P4080 erratum SERDES9 says that the SERDES receiver
lanes should be reset after the XAUI starts tranmitting alignment signals.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For P3060 and P4080, USB pins are multiplexed with other functions.
Update the device tree status for USB ports based on setting of
RCW[EC1] & RCW[EC2] which describe if pins are muxed to usb.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch is intended to initialize RMan LIODN related registers on
P2041, P304S and P5020 SocS. It also adds the "rman@0" child node to
qman-portal nodes, adds "fsl,liodn" property to RMan inbound block nodes.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update device tree handling for SRIO controller to support updated
fsl,srio device tree binding.
We handle disabling of individual ports, the whole controller, RMU, and
RMAN. Additionally, we setup the SRIO related LIODNs in the device
tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Properly set the LIODN values associated with SRIO controller. On
P4080/P3060 we have an LIODN per port and one for the RMU. On
P2041/P3041/P5020 we have 2 LIODNs per port.
Update the tables for all of these devices to properly handle both
styles.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There is a rather subtle build problem where the build time stamp is not
updated for out-of-tree builds if there exists an in-tree build which
has a valid timestamp file. So if you do an in-tree build, then an
out-of-tree build your timestamp will not change.
The correct timestamp_autogenerated.h lives in the object tree, but it
is not always found there. The source still lives in the source tree and
when compiling version.h, it includes timestamp_autogenerated.h. Since
the current directory is always searched first, this will come from the
source tree rather than the object tree if it exists there. This affects
dependency generation also, which means that common/cmd_version.o will not
even be rebuilt if you have ever done an in-tree build.
A similar problem exists with the version file.
This change moves both files into the 'generated' subdir, which is already
used for asm-offsets.h. Then timestamp.h and version.h are updated to
include the files from there.
There are other places where these generated files are included, but I
cannot see why these don't just use the timestamp.h and version.h headers.
So this change also tidies that up.
I have tested this with in- and out-of-tree builds, but not SPL. I have
looked at various other options for fixing this, including sed on the dep
files, -I- and -include flags to gcc, but I don't think they can be made
to work. Comments welcome.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
We want to keep all OS-dependent code in once place, with a simple interface
to U-Boot. For now, this is that place.
Signed-off-by: Simon Glass <sjg@chromium.org>
These files are taken from the ARM board implementation and then reduced
to remove unneeded cruft.
Ideally we would work towards unifying arch/xxx/lib files, particularly
board.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is an initial implementation with all functions defined but not working.
The lds file is very simple since we can mostly rely on the linker defaults.
Signed-off-by: Simon Glass <sjg@chromium.org>
This adds required header files for the sandbox architecture, and a basic
description of what sandbox is (README.sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
Common U-Boot API wants this define, so import asm/cache.h from Linux
to provide suitable defines.
Acked-by: Anton Staaf <robotboy@chromium.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This additionally updates mx31/generic.c by
- replacing __REG() macro accesses with readl() and writel()
- providing macros for PDR0 and PLL bit accesses
Signed-off-by: Helmut Raiger <helmut.raiger@hale.at>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
The top level Makefile does not do any recursion into subdirs when
cleaning, so these clean/distclean targets in random arch/board dirs
never get used. Punt them all.
MAKEALL didn't report any errors related to this that I could see.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
* 'master' of git://git.denx.de/u-boot-fdt:
powerpc/85xx: use fdt_create_phandle() to create the Fman firmware phandles
fdt: update fdt_alloc_phandle to use fdt_get_phandle
fdt: check for fdt errors in fdt_create_phandle
fdt: Add a do_fixup_by_path_string() function
Function fdt_create_phandle() conveniently creates new phandle properties
using both "linux,phandle" and "phandle", so it should be used by all code
that wants to create a phandle.
The Fman firmware code, which embeds an Fman firmware into the device tree,
was creating the phandle properties manually. Instead, change it to use
fdt_create_phandle().
Signed-off-by: Timur Tabi <timur@freescale.com>
The EC1_EXT, EC2_EXT, and EC3 bits in the RCW don't officially exist on the
P3060 and should always be set to zero.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P3041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P2041 has 10 qman portals, we need to configure all of them:
* As there are only 4 physical cores sdest can only be 0 to 3
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P5020 has 10 qman portals, we need to configure all of them:
* As there are only 2 physical cores sdest can only be 0 or 1
* We assign dqrr & frame data LIODNs for all portals so if they
are utilized the proper mapping tables can be setup uniquely
(PAMU stashing)
* We set Portal 6-10 to LIODN offsets 1-5 as the global LIODN
assignments are tuned around an assumption of at most 5
partitions.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Copy bootfile from variables
microblaze: Fix unaligned.h for endians
microblaze: Initialize jumptable and console
microblaze: Support flashes on lower addresses
microblaze: Call common console_init_f initialization function
Jz4740 is a multimedia application processor targeting for mobile
devices like e-Dictionary, eBook, portable media player (PMP) and
GPS navigator. Jz4740 is powered by Ingenic 360 MHz XBurst CPU core
(JzRISC), in which RISC/SIMD/DSP hybrid instruction set architecture
provides high integration, high performance and low power consumption.
JzRISC incorporated in Jz4740 is the advanced and power-efficient
32-bit RISC core, compatible with MIPS32, with 16K I-Cache and 16K
D-Cache, and can operate at speeds up to 400 MHz.
On-chip modules such as LCD controller, embedded audio codec, multi-
channel SAR-ADC, AC97/I2S controller and camera I/F offer a rich
suite of peripherals for multimedia application. NAND controller
(SLC/MLC), USB (host 1.1 and device 2.0), UART, I2C, SPI, etc. are
also available.
For more info about Ingenic XBurst Jz4740:
http://en.ingenic.cn/eng/http://www.linux-mips.org/wiki/Ingenic
This patch introduces XBurst CPU support in U-Boot. It's compatible
with MIPS32, but requires a bit different cache maintenance, timer
routines, and boot mechanism using USB boot tool, so XBurst support
can go into a separate new home, cpu/xburst/.
Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
1. The SD_DATA[4:7] signals are shared with the SPI chip selects on 8536DS,
so don't set MPC85xx_PMUXCR_SD_DATA that config eSDHC data bus-width
to 4-bit and enable SPI signals.
2. Add eSPI controller and SPI-FLASH definition.
Signed-off-by: Xie Xiaobo <r63061@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We really shouldn't be overwriting bat registers with translation enabled,
especially when we're executing code using one of them for translating
the current instruction stream. Instead, disable address translation
while doing the final BAT setup.
In order to do this, setup_bats has to move back to asm code, because we
require translation to be enabled to have a stack for C code. The yucky
thing about that is that the assembler doesn't like ULL so we have to
switch to using HIGH/LOW pairs for physical addresses that are > 32 bits
in length.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Function dtsec_configure_serdes() needs to know where the TBI PHY registers
are in order to configure SGMII for proper SerDes operation.
During SGMII initialzation, fm_eth_init_mac() passing NULL for 'phyregs'
when it called init_dtsec(), because it was believed that phyregs was not
used. In fact, it is used by dtsec_configure_serdes() to configure the TBI
PHY registers.
We also need to define the PHY registers in struct fm_mdio.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Interactive DDR debugging provides a user interface to view and modify SPD,
DIMM parameters, board options and DDR controller registers before DDR is
initialized. With this feature, developers can fine-tune DDR for board
bringup and other debugging without frequently having to reprogram the flash.
To enable this feature, define CONFIG_FSL_DDR_INTERACTIVE in board header
file and set an environment variable to activate it. Syntax:
setenv ddr_interactive on
After reset, U-boot prompts before initializing DDR controllers
FSL DDR>
The available commands are
print print SPD and intermediate computed data
reset reboot machine
recompute reload SPD and options to default and recompute regs
edit modify spd, parameter, or option
compute recompute registers from current next_step to end
next_step shows current next_step
help this message
go program the memory controller and continue with u-boot
The first command should be "compute", which reads data from DIMM SPDs and
board options, performs the calculation then stops before setting DDR
controller. A user can use "print" and "edit" commands to view and modify
anything. "Go" picks up from current step with any modification and
compltes the calculation then enables the DDR controller to continue u-boot.
"Recompute" does it over from fresh reading.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fix:
usb_ohci.c: In function 'dl_transfer_length':
usb_ohci.c:768:8: warning: variable 'tdINFO' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Remy Bohmer <linux@bohmer.net>
Fix:
board.c:445:8: warning: variable 'bd' set but not used [-Wunused-but-set-variable]
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This is long over due. All but two net drivers have been converted, but
those have now been dropped.
The only thing left to do is actually delete all references to NET_MULTI
and code that is compiled when that is not defined. So here we scrub the
core code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This pushes the ugly duplicated arch ifdef lists we maintain in various
image related files out to the arch headers themselves.
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Tested-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current post_log_word in global data is currently split into 2x
16 bits: half for the test start, half for the test success.
Since we alredy have more than 16 POST tests defined and more could
be defined, this may result in an overflow and the post_output_backlog
would not work for the tests defined further of these 16 positions.
An additional field is added to global data so that we can now support up
to 32 (depending of architecture) tests. The post_log_word is only used
to record the start of the test and the new field post_log_res for the
test success (or failure). The post_output_backlog is for this change
also adapted.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
For post to run on ARM, 3 things are needed:
- post_log_word to be defined in gd
- a post.h include in arch/arm/lib/board.c
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Allow redirection of console output prior to console initialisation to a
temporary buffer.
To enable this functionality, the board (or arch) must define:
- CONFIG_PRE_CONSOLE_BUFFER - Enable pre-console buffer
- CONFIG_PRE_CON_BUF_ADDR - Base address of pre-console buffer
- CONFIG_PRE_CON_BUF_SZ - Size of pre-console buffer (in bytes)
The pre-console buffer will buffer the last CONFIG_PRE_CON_BUF_SZ bytes
Any earlier characters are silently dropped.
* 'master' of git://git.denx.de/u-boot-mpc85xx:
powerpc/p3060: Add SoC related support for P3060 platform
powerpc/85xx: Add support for setting up RAID engine liodns on P5020
powerpc/85xx: Refactor some defines out of corenet_ds.h
fm-eth: Add ability for board code to disable a port
powerpc/mpc8548: Add workaround for erratum NMG_LBC103
powerpc/mpc8548: Add workaround for erratum NMG_DDR120
powerpc/mpc85xxcds: Fix PCI speed
powerpc/mpc8548cds: Fix booting message
powerpc/p4080: Add support for secure boot flow
powerpc/85xx: Add Secure Boot support on P1010RDB for NOR, NAND & SPIFLASH
powerpc/85xx: Add PBL & SECUREBOOT support on P3041/P5020DS boards
powerpc/p2041rdb: remove watch dog related codes
powerpc/p2041rdb: updated description of cpld command
powerpc/p2041rdb: add more ddr frequencies support
powerpc/p2041rdb: set sysclk according to status of physical switch SW1
powerpc/p2041rdb: update cpld reset command according to CPLD 2.0
powerpc/mpc8349emds: Migrate from spd_sdram to unified DDR driver
powerpc/mpc83xx: Migrate from spd_sdram to unified DDR driver
powerpc/mpc8xxx: Add DDR2 to unified DDR driver
powerpc/mpc8xxx: Fix picos_to_mclk() and get_memory_clk_period_ps()
powerpc/mpc8xxx: Add SPD EEPROM address for single controller 2 slots
powerpc/mpc8xxx: Fix DDR code for empty first DIMM slot and enable DQS_en
powerpc/85xx: Refactor P2041RDB to use common p_corenet files
powerpc/85xx: refactor common P-Series CoreNet files for FSL boards
powerpc/85xx: Enable CMD_REGINFO on corenet boards
powerpc/85xx: p2041rdb - Remove unused 'execute' perm in TLB entries
powerpc/85xx: Fix USB protocol definitions for P1020RDB
powerpc/corenet_ds: Use separated speed tables for UDIMM and RDIMM
powerpc/mpc8xxx: Move DDR RCW overriding to common code
powerpc/mpc8xxx: Extend CWL table
powerpc/85xx: Cleanup how SVR_MAJ() is defined on MPC8536
powerpc/85xx: Cleanup extern in corenet_ds board code
powerpc/p2041rdb: Add ethernet support on P2041RDB board
powerpc/85xx: Add networking support to P1023RDS
powerpc/hydra: Add ethernet support on P5020/P3041 DS boards
powerpc/85xx: Add FMan ethernet support to P4080DS
powerpc/85xx: Add support for FMan ethernet in Independent mode
powerpc/mpc8548cds: Cleanup mpc8548cds.c
powerpc/mp: add support for discontiguous cores
powerpc/85xx: corenet_ds - Remove unused 'execute' perm in TLB entries
fdt: Add new fdt_create_phandle helper
fdt: Rename fdt_create_phandle to fdt_set_phandle
powerpc/85xx: Fix compile warnings/errors if CONFIG_SYS_DPAA_FMAN isn't set
fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
powerpc/85xx: Expanding the window of CCSRBAR in AS=1 from 4k to 1M
powerpc/85xx: Add NAND/NAND_SPL support to P1010RDB
nand: Freescale Integrated Flash Controller NAND support
powerpc/85xx: Add basic support for P1010RDB
powerpc/85xx: Add support for new P102x/P2020 RDB style boards
powerpc/85xx: relocate CCSR before creating the initial RAM area
powerpc/85xx: introduce and document CONFIG_SYS_CCSRBAR macros
powerpc/85xx: Enable internal USB UTMI PHY on p204x/p3041/p50x0
powerpc/85xx: Add ULPI and UTMI USB Phy support for P1010/P1014
Add P3060 SoC specific information:cores setup, LIODN setup, etc
The P3060 SoC combines six e500mc Power Architecture processor cores with
high-performance datapath acceleration architecture(DPAA), CoreNet fabric
infrastructure, as well as network and peripheral interfaces.
Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for Job Queue/Ring LIODN for the RAID Engine on P5020. Each
Job Queue/Ring combo needs one id assigned for a total of 4 (2 JQs/2
Rings per JQ). This just handles RAID Engine in non-DPAA mode.
Signed-off-by: Santosh Shukla <santosh.shukla@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].
Refer to the erratum LBIU3 of mpc8548.
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.
Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Pre u-boot Flow:
1. User loads the u-boot image in flash
2. PBL/Configuration word is used to create LAW for Flash at 0xc0000000
(Please note that ISBC expects all these addresses, images to be
validated, entry point etc within 0 - 3.5G range)
3. ISBC validates the u-boot image, and passes control to u-boot
at 0xcffffffc.
Changes in u-boot:
1. Temporarily map CONFIG_SYS_MONITOR_BASE to the 1M
CONFIG_SYS_PBI_FLASH_WINDOW in AS=1.
(The CONFIG_SYS_PBI_FLASH_WINDOW is the address map for the flash
created by PBL/configuration word within 0 - 3.5G memory range. The
u-boot image at this address has been validated by ISBC code)
2. Remove TLB entries for 0 - 3.5G created by ISBC code
3. Remove the LAW entry for the CONFIG_SYS_PBI_FLASH_WINDOW created by
PBL/configuration word after switch to AS = 1
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Signed-off-by: Kuldip Giroh <kuldip.giroh@freescale.com>
Acked-by: Wood Scott-B07421 <B07421@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Remove code copying
- Reset address is setup from first stage bootloader
- Support reset vector setup on little endian
Signed-off-by: Michal Simek <monstr@monstr.eu>
Use one memory space to detect little/big endian platforms.
The first unused address(0x28) is used instead 0x0 address (reset vectors).
Detection rewrited reset vector setup from first stage bootloader.
Workflow:
1. Store 0x28 to r7
2. Do little/big endian test
3. Restore r7 to 0x28
Signed-off-by: Michal Simek <monstr@monstr.eu>
For example: Setup reset vectors if reset address is setup.
Setup user exception vector if user exception is enabled
Signed-off-by: Michal Simek <monstr@monstr.eu>
The EST SBC8260 is over 10 years old, and the SBC8240 older than
that. With the tiny amount of RAM (by today's standards), there
really isn't anyone interested in running the latest U-boot on
these EOL products anymore.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: jon.diekema@smiths-aerospace.com
There are some locations in the code which anticipate printf() being called
before the console is ready by squelching printf() on gd->have_console.
Move this squelching into printf(), vprintf(), puts() and putc(). Also
make tstc() and getc() return 0 if console is not yet initialised
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Tested-by: Simon Glass <sjg@chromium.org>
* 'post' of git://git.denx.de/u-boot-blackfin:
Blackfin: uart: implement loop callback for post
Blackfin: bf537-stamp/bf548-ezkit: update POST flash block range
Blackfin: post: generalize led/button tests with GPIOs
Blackfin: bf537-stamp: drop uart/flash post tests
Blackfin: post: drop custom test list
Blackfin: bf537-stamp: convert to gpio post hotkey
When building the zmx25 target we get:
Configuring for zmx25 board...
generic.c:108: warning: 'get_reset_cause' defined but not used
Fix this warning by defining get_reset_cause only if CONFIG_DISPLAY_CPUINFO is defined.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Liu <jason.hui@linaro.org>
Acked-by: Jason Liu <jason.hui@linaro.org>
The PLL decoding algorithm didn't take into account many configuration bits.
Adjust it according to Linux kernel. Also, add PLL4 for MX53.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Jason Hui <jason.hui@linaro.org>
Tested-by: Jason Liu <Jason.hui@linaro.org>
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Turn on the watchdog WDZST bit so that watchdog timer does not count during low power modes.
Prior to applying this patch mx31pdk board got watchdog resets because when it booted in the Linux prompt
and there was no activity, the system entered into idle mode while watchdog timer was still active.
Fix this by disabling watchdog timer during idle mode.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Currently the reset cause is printed like:
CPU: Freescale i.MX31 rev 2.0 at 531 MHz.Reset cause: POR
Improve readability by adding a new line like it is done on other i.MX boards.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Building without option CONFIG_DISPLAY_CPUINFO leads to
this warning:
sys_info.c:50:14: warning: 'rev_s_37xx' defined but not used
Signed-off-by: Sanjeev Premi <premi@ti.com>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Config VMMC voltage to 3V for MMC/SD card slot
and PBIAS settings needed for OMAP4
Fixes MMC/SD detection on boot from eMMC.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
split-up spl.c into spl.c, spl_mmc.c and spl_nand.c. This avoids problems
with missing defines if a board does not use mmc or nand. This includes
adding spl_ prefix to some functions which are now public. spl_image_t is now
a public type. Added some of the common functions to omap-common.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Implements the saving of boot params passed by OMAP3 ROM code.
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Support for the new spl structure. Using the interface defined by Aneesh V for
OMAP4
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3 relied on the memory config done by X-loader or Configuration Header. This
has to be reworked for the implementation of a SPL. This patch configures RAM
bank 0 if CONFIG_SPL_BUILD is set. Settings for Micron-RAM used by devkit8000
are added to mem.h
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Moves the early UART clock setup setup_clocks_for_console() from
preloader_console_init() to s_init() of OMAP4.
This is done to prepare for OMAP3 integration.
This patch was posted seperatly to the mailinglist but I decidet - since it is
a prereqesit for this patch to add it. Former port to ML:
http://article.gmane.org/gmane.comp.boot-loaders.u-boot/104395
Signed-off-by: Simon Schwarz <simonschwarzcor@gmail.com>
Signed-off-by: Tom Rini <trini@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The existing timing does not quite meet the minimum requirements
in the LAN9221 datasheet. The timing in this patch solves problems
noticed on some parts. The patch also combines the CS configuration
for the overo and igep0020 boards per request.
Signed-off-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch enables ethernet support for Marvell GplugD board. Network
related commands works.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
This patch adds support for Fast Ethernet Controller driver for
Armada100 series.
Signed-off-by: Ajay Bhargav <ajay.bhargav@einfochips.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Unified DDR driver is maintained for better performance, robustness and bug
fixes. Upgrading to use unified DDR driver for MPC83xx takes advantage of
overall improvement. It requires changes for board files to customize
platform-dependent parameters.
To utilize the unified DDR driver, a board needs to define CONFIG_FSL_DDRx
in the header file. No more boards will be accepted without such definition.
Note: the workaround for erratum DDR6 for the very old MPC834x Rev 1.0/1.1
and MPC8360 Rev 1.1/1.2 parts is not migrated to unified driver.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR2 has different ODT table and values. Adding table according to Samsung
application note.
Fix additive latency calculation to avoid interger underflow.
Also converted typedef dynamic_odt_t to struct dynamic_odt.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The two slots on the same controller have different addresses.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Check second DIMM slot in case the first one is empty.
Honor DQS enable option for SDRAM mode register.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DDR RCW varies at different speeds. It is common for all platform. Move it
out from corenet_ds.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extend CAS write Latency (CWL) table to comply with DDR3 spec
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8536 seems to use only 3 bits for the major revision field in the
SVR rather than the 4 bits used by all other processors. The most
significant bit is used as a mfg code on MPC8536.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The P1023 has two 1G ethernet controllers the first can run in
SGMII, RGMII, or RMII. The second can only do SGMII & RGMII.
We need to setup a for SoC & board registers based on our various
configuration for ethernet to function properly on the board.
Removed CONFIG_SYS_FMAN_FW as its not used anywhere.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Frame Manager (FMan) on QorIQ SoCs with DPAA (datapath acceleration
architecture) is the ethernet contoller block. Normally it is utilized
via Queue Manager (Qman) and Buffer Manager (Bman). However for boot
usage the FMan supports a mode similar to QE or CPM ethernet collers
called Independent mode.
Additionally the FMan block supports multiple 1g and 10g interfaces as a
single entity in the system rather than each controller being managed
uniquely. This means we have to initialize all of Fman regardless of
the number of interfaces we utilize.
Different SoCs support different combinations of the number of FMan as
well as the number of 1g & 10g interfaces support per Fman.
We add support for the following SoCs:
* P1023 - 1 Fman, 2x1g
* P4080 - 2 Fman, each Fman has 4x1g and 1x10g
* P204x/P3041/P5020 - 1 Fman, 5x1g, 1x10g
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Dai Haruki <dai.haruki@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@freescale.com>
Signed-off-by: Lei Xu <B33228@freescale.com>
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Shaohui Xie <b21989@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some SOCs have discontiguously-numbered cores, and so we can't determine the
valid core numbers via the FRR register any more. We define
CPU_TYPE_ENTRY_MASK to specify a discontiguous core mask, and helper functions
to process the mask and enumerate over the set of valid cores.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old fdt_create_phandle didn't actually create a phandle it just
set one. We'll introduce a new helper that actually does creation.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Gerald Van Baren <vanbaren@cideas.com>
Add ifdef protection around fman specific code related to device tree
clock setup. If we dont have CONFIG_SYS_DPAA_FMAN defined we shouldn't
be executing this code.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.
Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.
Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.
Impact:
Boot from IFC may not be successful if IFC_CS3 is used.
Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size
Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data
Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For an IFC Erratum (A-003399) we will need to access IFC registers in
cpu_init_early_f() so expand the TLB covering CCSR to 1M.
Since we need a TLB to cover 1M we move to using TLB1 array for all the
early mappings so we can cover various sizes beyond 4k.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add NAND support (including spl) on IFC, such as is found on the p1010.
Note that using hardware ECC on IFC with small-page NAND (which is what
comes on the p1010rdb reference board) means there will be insufficient
OOB space for JFFS2, since IFC does not support 1-bit ECC. UBI should
work, as it does not use OOB for anything but ECC.
When hardware ECC is not enabled in CSOR, software ECC is now used.
Signed-off-by: Dipen Dudhat <Dipen.Dudhat@freescale.com>
[scottwood@freescale.com: ECC rework and misc fixes]
Signed-off-by: Scott Wood <scottwood@freescale.com>
Before main memory (DDR) is initialized, the on-chip L1 cache is used as a
memory area for the stack and the global data (gd_t) structure. This is
called the initial RAM area, or initram. The L1 cache is locked and the TLBs
point to a non-existent address (so that there's no chance it will overlap
main memory or any device). The L1 cache is also configured not to write
out to memory or the L2 cache, so everything stays in the L1 cache.
One of the things we might do while running out of initram is relocate CCSR.
On reset, CCSR is typically located at some high 32-bit address, like
0xfe000000, and this may not be the best place for CCSR. For example, on
36-bit systems, CCSR is relocated to 0xffe000000, near the top of 36-bit
memory space.
On some future Freescale SOCs, the L1 cache will be forced to write to the
backing store, so we can no longer have the TLBs point to non-existent address.
Instead, we will point the TLBs to an unused area in CCSR. In order for this
technique to work, CCSR needs to be relocated before the initram memory is
enabled.
Unlike the original CCSR relocation code in cpu_init_early_f(), the TLBs
we create now for relocating CCSR are deleted after the relocation is finished.
cpu_init_early_f() will still need to create a TLB for CCSR (at the new
location) for normal U-Boot purposes. This is done to keep the impact to
existing U-Boot code minimal and to better isolate the CCSR relocation code.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Introduce the CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW
macros, which contain the high and low portions of CONFIG_SYS_CCSRBAR_PHYS.
This is necessary for the assembly-language code that relocates CCSR, since
the assembler does not understand 64-bit constants.
CONFIG_SYS_CCSRBAR_PHYS is automatically defined from the
CONFIG_SYS_CCSRBAR_PHYS_HIGH and CONFIG_SYS_CCSRBAR_PHYS_LOW macros, so it
should not be defined in a board header file. Similarly,
CONFIG_SYS_CCSRBAR_DEFAULT is defined for each SOC in config_mpc85xx.h, so
it should also not be defined in the board header file.
CONFIG_SYS_CCSR_DO_NOT_RELOCATE is a "short-cut" macro that guarantees that
CONFIG_SYS_CCSRBAR_PHYS is set to the same value as CONFIG_SYS_CCSRBAR_DEFAULT,
and so CCSR will not be relocated.
Since CONFIG_SYS_CCSRBAR_DEFAULT is locked to a fixed value, multi-stage U-Boot
builds (e.g. NAND) are required to relocate CCSR only during the last stage
(i.e. the "real" U-Boot). All other stages should define
CONFIG_SYS_CCSR_DO_NOT_RELOCATE to ensure that CCSR is not relocated.
README is updated with descriptions of all the CONFIG_SYS_CCSRBAR_xxx macros.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add UTMI and ULPI PHY support for USB controller on qoriq series of
processors with internal UTMI PHY implemented, for example P1010/P1014
- Use both getenv() and hwconfig to get USB phy type till getenv()
is depricated
- Introduce CONFIG_SYS_FSL_USB_INTERNAL_UTMI_PHY to specify if soc
has internal UTMI phy
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The few tests that are Blackfin-specific have been migrated to common
code or been rewritten with the existing "bsp-specific" defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Flush the dcache before removing the TLB with caches enabled.
Otherwise this might lead to problems later on, e.g. while booting
Linux (as seen on ICON-440SPe).
Signed-off-by: Stefan Roese <sr@denx.de>
Change bd_t->bi_phy* arrays from 1 to 2 for PPC405EX since
405EX has 2 ethernet interfaces.
Signed-off-by: Bernhard Weirich <bernhard.weirich@riedel.net>
Signed-off-by: Stefan Roese <sr@denx.de>
Result of running the following command to address Wolfgang's
comment about camel case:
for file in `find . | grep '\.[chS]$'`; do perl -i -pe
's/(green|yellow|red|blue)_LED_(on|off)/$1_led_$2/g' $file; done
Discussion:
http://patchwork.ozlabs.org/patch/84988/
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Tuning some IO settings for better performance and power.
And consolidate all such IO settings at one place.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
SDRAM init was not working on ES1.0 due to a programming
error. A pointer that was passed by value to a function
was set in function emif_get_device_details(), but the effect
wouldn't be seen in the calling function. The issue came
out while testing for ES1.0 because ES1.0 doesn't have any
SDRAM chips connected to CS1
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch contains the generic changes required after
change to generic API in the previous patch.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Convert all OMAP specific functions to use the common API
definitions in include/asm/gpio.h. In the process, made
few additional changes:
- Use -EINVAL consistently. -1 was used in many places.
- Removed one-liner static functions that were used only
once. Replaced the content as necessary.
- Combines implementation of functions omap_get_gpio_dataout()
and omap_get_gpio_datain(). To do so, new static function
_get_gpio_direction() was added.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
OMAP3: Add 37xx ESx revision numbers.
Signed-off-by: Michael Jones <michael.jones@matrix-vision.de>
Signed-off-by: Howard D. Gray <howard.gray@matrix-vision.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Read directly from OMAP_GPIO_DATAOUT to get the output state of the GPIO pin
Signed-off-by: Joel A Fernandes <agnel.joel@gmail.com>
Signed-off-by: Jason Kridner <jkridner@beagleboard.org>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Commit 21726a7 "Add assert() for debug assertions" caused build
warnings for all tegra2 based boards:
clock.c:36:1: warning: "assert" redefined
In file included from clock.c:29:
include/common.h:144:1: warning: this is the location of the previous definition
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Move the TIMER_ definitions before they are used in KS8695 timer.c code.
Fixes:
timer.c: In function ‘timer_init’:
timer.c:37: error: ‘TIMER_COUNT’ undeclared (first use in this function)
timer.c:37: error: (Each undeclared identifier is reported only once
timer.c:37: error: for each function it appears in.)
timer.c:38: error: ‘TIMER_PULSE’ undeclared (first use in this function)
Signed-off-by: Greg Ungerer <greg.ungerer@opengear.com>
Commit 17659d7 "Timer: Remove reset_timer_masked()" introduced a
static declaration for reset_timer_masked() which causes build errors:
timer.c:45: error: static declaration of 'reset_timer_masked' follows non-static declaration
include/asm/u-boot-arm.h:70: error: previous declaration of 'reset_timer_masked' was here
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Graeme Russ <graeme.russ@gmail.com>
Cc: Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
commit 0edf8b5b2f breaks
building on a different directory with the O= parameter.
The patch wil fix this issue, generating always asm-offsets.h before
the other targets.
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Matthias Weisser <weisserm@arcor.de>
CC: Wolfgang Denk <wd@denx.de>
Since we are loading an executable image into memory we need flush it
out of the cache to possible maintain coherence on CPUs with split
instruction and data caches. We do this for other executable image
loading command.
On PowerPC once we do this we no longer need to explicitly flush the
dcache on multi-core systems in the BOOTM_STATE_OS_PREP phase. We now
treat the BOOTM_STATE_OS_PREP as a no-op to maintain backwards
compatibility with the bootm subcommand.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Diana CRACIUN <Diana.Craciun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'master' of git://git.denx.de/u-boot-coldfire:
ColdFire:Clean up the CONFIG_STANDALONE_LOAD_ADDR usage
ColdFire:Add mb for 5253 dram initialization
ColdFire:Define the DM9000 byteswap for M5253 board.
ColdFire:Update the env settings for several boards.
ColdFire:disable the NFS define for 52277 board.
ColdFire:Update the timer_init since it was unified.
ColdFire: Cleanup for partial linking and --gc-sections
ColdFire: Update compile flags for each CPUs
ColdFire:Fix the configuration broken for some boards.
* 'master' of git://git.denx.de/u-boot-arm: (145 commits)
beagleboard: enable HUB power on all variants of the BeagleBoard
dm3730: enable dpll5
ehci-hcd: Allow cleanups to happen gracefully on a timeout.
OMAP3: Add DSS driver for OMAP3
led: Remove state-saving of led for toggle functionality and add toggle option to led command
led: Fixed setting of STATUS_LED_BIT1 when led_name is 'all'
led: correct off/on locations in structure
led: added cmd_led to Makefile
BeagleBoard: fix LED 0/1 in driver
Corrected LED name match finding avoiding extraneous Usage printouts
BeagleBoard: config: updated default configuration
BeagleBoard: config: Enabled multibus support for I2C in configuration
BeagleBoard: config: add optargs/buddy/camera
BeagleBoard: config: increase command-line functionality
BeagleBoard: config: make mtest run
BeagleBoard: config: enable DSS
BeagleBoard: config: enable asix driver and dhcp
BeagleBoard: config: enable networking
BeagleBoard: config: decrease bootdelay to 2 seconds
BeagleBoard: config: use uImage.beagle for tftp
BeagleBoard: config: hardcode MAC for onboard SMSC
BeagleBoard: config: load kernel from MMC ext, not FAT
BeagleBoard: Configure DVI/S-video
BeagleBoard: Added userbutton command
BeagleBoard: turn off clocks in ehci_stop
USB: Remove __attribute__ ((packed)) for struct ehci_hccr and ehci_hcor
beagleboard: add support for xM revision C
beagle: pass expansionboard name in bootargs
OMAP: Remove omapfb.debug=y from Beagle and Overo env settings
OMAP3 Beagle Pin Mux initialization glitch fix
da850: modifications for Logic PD Rev.3 AM18xx EVM
da850: fix the channel number for EMAC teardown init
da850: add support for Spectrum Digital AM18xx EVM
da850: add support to wake up DSP during board init
da850: modify the U-Boot prompt string
da850: add NOR boot mode support
da8xx: add support for multiple PLL controllers
da850: indicate cache usage disable in config file
dm365: modify boot prompt from dm365 to dm36x
dm365: disable cache usage due to coherency issues
dm6446: disable cache usage due to coherency issues
OMAP3: Remove legacy mmc driver
devkit8000: Use generic MMC driver
TI OMAP3 SDP3430: Use generic MMC driver
AM3517 CraneBoard: Use generic MMC driver
OMAP3: pandora: Use generic MMC driver
OMAP3: Zoom2: Use generic MMC driver
OMAP3: Zoom1: Use generic MMC driver
OMAP3: DIG297: Use generic MMC driver
OMAP3: CM-T35: Use generic MMC driver
am3517evm: Use generic MMC driver
omap3evm: Use generic MMC driver
omap3:clock: check cpu_family before enabling clks for IVA & CAM
omap3:clock: configure GFX clock to 200MHz for AM/DM37x
OMAP3/4: Increase console I/O buffer size
PXA: vpac270: Remove re-defined CONFIG_SYS_TEXT_BASE
PXA: Fix CSB226, fix monitor length
PXA: Fix Lubbock, remove redundant parenthesis
armv7: cache: remove flush on un-aligned invalidate
armv7: stronger barrier for cache-maintenance operations
omap: enable caches at system start-up
arm: do not force d-cache enable on all boards
ORIGEN: Add MMC SPL support
ARMV7: Add support for Samsung ORIGEN board
i2c:gpio:s5p: Enable I2C GPIO on the GONI target
i2c:gpio:s5p: I2C GPIO Software implementation (via soft_i2c)
Tegra2: Use clock and pinmux functions to simplify code
Tegra2: Add additional pin multiplexing features
Tegra2: Add more clock support
Tegra2: Add microsecond timer function
ARM: remove broken "at91rm9200dk" board
ARM: remove broken "m501sk" board
ARM: remove broken "kb9202" board
ARM: remove broken "csb637" board
ARM: remove broken "cmc_pu2" board
ARM: remove broken "at91cap9adk" board
ARM: remove broken "voiceblue" board
ARM: remove broken "smdk2400" board
ARM: remove broken "sbc2410x" board
ARM: remove broken "netstar" board
ARM: remove broken "mx1fs2" board
ARM: remove broken "lpd7a40x" boards
ARM: remove broken "edb93xx" boards
ARM: remove broken "B2" board
ARM: remove broken "armadillo" board
ARM: remove broken "assabet" board
ARM: versatile: drop warnings
IMX: scb9328: drop warnings
MX31: imx31_litekit: make use of GPIO framework
MX31: mx31ads: make use of GPIO framework
MX5: mx51evk: make use of GPIO framework
MX35: mx35pdk: make use of GPIO framework
MX5: mx53loco: make use of GPIO framework
MX5: mx53evk: make use of GPIO framework
MX5: vision2: make use of GPIO framework
MX5: mx53smd: make use of GPIO framework
MX5: mx53ard: make use of GPIO framework
MX25: zmx25: make use of GPIO framework
MX5: efikamx: make use of GPIO framework
MX31: QONG: make use of GPIO framework
MX35: make use of GPIO framework for MX35 processor
MX5: make use of GPIO framework for MX5 processor
MX31: make use of GPIO framework for MX31 processor
MX25: make use of GPIO framework for MX25 processor
IMX: uniform GPIO interface using GPIO framework
MX: MX35 / MX5: uniform clock command with powerpc
MX35: MX35PDK: support additional RAM on CSD1
mx53: ddr3: Update DD3 initialization
ARM: MX51: PLL errata workaround
ARM: versatilepb : drop warnings due to double definitions
omap4: increase SRAM budget to fix build error
omap4: fix build warning due to signed unsigned comparison
mkimage: Fix 'Unknown OMAP image type - 5'
omap: fix gpio related build breaks
gpio:samsung: s5p_ suffix add for GPIO functions (C210_universal)
SMDKV310: MMC SPL: Remove unwanted dummy functions
SMDKV310: Fix undefined reference error
SMDKV310: Fix build error for smdkv310 board
gpio:samsung s5p_ suffix add for GPIO functions
mmc: S5P: Support DMA restarts at buffer boundaries
SMDKV310: Fix host compilation of mkv310_image
arm: fix bd pointer dereference prior initialization
arm, lib/board.c: use gd->ram_size instead of bd->bi_memsize
mx5: Remove CONFIG_L2_OFF and CONFIG_SYS_L2CACHE_OFF
MX31: removed warnings due to clock.h
integrator: convert to new build system
integratorcp: make the board compile
integratorap: remove hardcoded 32MB memory cmdline
...
The dram initialization sequence should be in order.
This patch add mb for the dram intialization code to make
sure the compiler do not disorder the code.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
