The company Samtec was merged into Softing, migrate the board over to
the new name and update copyright headers.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Silvio Fricke <silvio.fricke@softing.com>
Cc: Stefano Babic <sbabic@denx.de>
The DM iMX PCI driver has DM_FLAG_OS_PREPARE set and will call
imx_pcie_remove() from the .remove callback. Do not call it from
the architecture code again.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Bin Meng <bmeng.cn@gmail.com>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This commit adds initial support for the Toradex Apalis iMX8QM 4GB WB IT
V1.0B module. Unlike the V1.0A early access samples exclusively booting
from SD card, they are now strapped to boot from eFuses which are
factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Gigabit Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QM as of yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
CPU frequency reporting failed with the following error message being
printed:
sc_pm_get_clock_rate: resource:507 clk:2: res:3
Could not read CPU frequency: -22
CPU: NXP i.MX8QM RevB A53 at 0 MHz
Fix this by differentiating between the A35 as found on the i.MX 8QXP
and the A53 as found on the i.MX 8QM SoCs.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Max Krummenacher <max.krummenacher@toradex.com>
Correct uart clock root ID. Incorrect ID may result the
clock is gated because rate value 0 is returned in
imx_get_uartclk()
The ID can be ignored if CONFIG_SKIP_LOWLEVEL_INIT is not enabled
because init_clk_uart() will enable all uart clocks in that case.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Skip secure related initialization in arch_cpu_init if low level
init is skipped. Because these should be done in early stage
firmware, such as ARM trusted firmware.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
in case CONFIG_MULTI_DTB_FIT is set and u-boot-dtb.imx
image is build, currently u-boot-dtb.bin is used for
generating the u-boot-dtb.imx binary, which is wrong, as
it contains only a dtb blob not the fit.blob
Use instead the u-boot-fit-dtb.bin for generating
u-boot-dtb.imx which contains the fit.blob.
Signed-off-by: Heiko Schocher <hs@denx.de>
Add common plugin codes to call ROM's hwcnfg_setup and generate IVT2
header.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This commit adds initial support for the Toradex Colibri iMX8QXP 2GB WB
IT V1.0B module. Unlike the V1.0A early access samples exclusively
booting from SD card, they are now strapped to boot from eFuses which
are factory fused to properly boot from their on-module eMMC. U-Boot
supports either booting from the on-module eMMC or may be used for
recovery purpose using the universal update utility (uuu) aka mfgtools
3.0.
Functionality wise the following is known to be working:
- eMMC and MMC/SD card
- Ethernet
- GPIOs
- I2C
Unfortunately, there is no USB functionality for the i.MX 8QXP as of
yet.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Building with Travis CI complained and stopped with the following error:
+cc1: fatal error: opening output file spl/u-boot-spl.cfgout: No such
file or directory
+compilation terminated.
This fixes commit caceb739ea ("imx: build flash.bin for i.MX8") which
took SPL being enabled on i.MX8 for granted.
Reported-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
We currently have duplicate definitions for BOARD_SIZE_CHECK in Makefile
and arch/arm/mach-imx/Makefile.
Move the board size check from arch/arm/mach-imx/Makefile to Makefile.
Depending on the value of CONFIG_BOARD_SIZE_LIMIT an error like an error
like the following is thrown:
u-boot-dtb.imx exceeds file size limit:
limit: 503696 bytes
actual: 509720 bytes
excess: 6024 bytes
make: *** [Makefile:1051: u-boot-dtb.imx] Error 1
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Sometimes we met SERROR, but only to catch it when Linux boots up.
Let's enable catching in U-Boot to catch it ealier and ease debug.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Correct CPU_ARM926EJS1 to CPU_ARM926EJS.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Allow using bootaux also on VF610 aka Vybrid.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Extend the driver to build with DM_VIDEO enabled. DTS files
must additionally include 'u-boot,dm-pre-reloc' property in
soc and ipu nodes to enable driver binding to ipu device.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Currently the CPU frequency is incorrectly reported:
CPU: NXP i.MX8QXP RevB A35 at 147228 MHz
Fix this problem by using a direct call to the SCU firmware to
retrieve the Cortex A35 CPU frequency.
With this change applied the CPU frequency is displayed correctly:
CPU: NXP i.MX8QXP RevB A35 at 1200 MHz
Tested-by: Marcelo Macedo <marcelo.macedo@nxp.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Select CONFIG_DM_MMC=y in order to support MMC driver model.
This allows the MMC board related code to be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
This makes get_imx_reset_cause() accessible in SPL, but keeps the SRSR
register content intact so that U-Boot proper can evaluated the
reset_cause again should this be needed.
Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
This patch extends the vf610 DDR memory controller code to support SW
leveling.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
This patch provides the code to calibrate the DDR's
DQS to DQ signals (RDLVL).
It is based on:
VFxxx Controller Reference Manual, Rev. 0, 10/2016, page 1600
10.1.6.16.4.1 "Software Read Leveling in MC Evaluation Mode"
and NXP's community thread:
"Vybrid: About DDR leveling feature on DDRMC."
https://community.nxp.com/thread/395323
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Replace CONFIG_SPL_FAT_SUPPORT with CONFIG_SPL_FS_FAT so
obj-$(CONFIG_$(SPL_)FS_FAT) can be used to control the build in both
SPL and U-Boot.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
When framebuffer driver init is failed, we should return the err value not 0.
So the video init can exit immediately.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Passover info only for revA.
move get_cpu_rev out of CONFIG_CPU to avoid build failure when using
get_cpu_rev in SPL.
Add a CONFIG_SPL_BUILD for passover usage, no need to execute it again
in normal U-Boot stage. Also if still checking passover info in normal
U-Boot stage, need to make the passover code executed after
arch_cpu_init_dm.
So to make it easy and clean, only execute the code for SPL stage.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Apply errata based on PL310 version instead of compile
time. Also set Prefetch offset to 15, since it improves
memcpy performance by 35%. Don't enable Incr double
Linefill enable since it adversely affects memcpy
performance by about 32MB/s and reads by 90MB/s. Tested
with 4K to 16MB sized src and dst aligned buffer.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
At default, u-boot reserves the memory from SP - 4KB to DRAM end for
lmb in arch_lmb_reserve. So lmb won't allocate any memory from it.
But we found the 4K gap for SP is not enough now, because some FDT
updating operations are added in our u-boot before jumping to kernel,
which needs larger stack. This causes the lmb allocated memory is overwritten
by stack.
Fix the issue by implementing the board_lmb_reserve to reserve from
SP - 16KB to memory end for lmb.
Signed-off-by: Ye Li <ye.li@nxp.com>
SPL runs in EL3 mode, except MU0_A, others are not powered on,
and could not be used. However normal U-Boot use MU1_A, so we
could not reuse the one in dts. And we could not replace the one
in dts with MU0_A, because MU0_A is reserved in secure world.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Like it was done on imx6 in commit 9236269de5 ("imx: mx6: Fix
implementantion reset_misc")
Do not call lcdif_power_down() in the SPL case to fix the following
build error:
LD spl/u-boot-spl
MKIMAGE u-boot.img
arch/arm/mach-imx/built-in.o: In function `reset_misc':
/home/fabio/ossystems/u-boot/arch/arm/mach-imx/mx7/soc.c:372: undefined reference to `lcdif_power_down'
scripts/Makefile.spl:375: recipe for target 'spl/u-boot-spl' failed
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Port for the PHYTEC phyBOARD-i.MX6UL-Segin single board computer. Based on
the PHYTEC phyCORE-i.MX6UL SOM (PCL063).
CPU: Freescale i.MX6UL rev1.2 528 MHz (running at 396 MHz)
CPU: Industrial temperature grade (-40C to 105C) at 44C
Reset cause: POR
Board: PHYTEC phyCORE-i.MX6UL
I2C: ready
DRAM: 256 MiB
NAND: 512 MiB
MMC: FSL_SDHC: 0
In: serial
Out: serial
Err: serial
Net: FEC0
Working:
- Eth0
- i2C
- MMC/SD
- NAND
- UART (1 & 5)
- USB (host & otg)
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
The following NXP application notes and manual recommend to ensure the
IVT DCD pointer is Null prior to calling HAB API authenticate_image()
function:
- AN12263: HABv4 RVT Guidelines and Recommendations
- AN4581: Secure Boot on i.MX50, i.MX53, i.MX 6 and i.MX7 Series using
HABv4
- CST docs: High Assurance Boot Version 4 Application Programming
Interface Reference Manual
Commit ca89df7dd4 ("imx: hab: Convert DCD non-NULL error to warning")
converted DCD non-NULL error to warning due to the lack of documentation
at the time of first patch submission. We have warned U-Boot users since
v2018.03, and it makes sense now to follow the NXP recommendation to
ensure the IVT DCD pointer is Null.
DCD commands should only be present in the initial boot image loaded by
the SoC ROM. Starting in HAB v4.3.7 the HAB code will generate an error
if a DCD pointer is present in an image being authenticated by calling the
HAB RVT API. Older versions of HAB will process and run DCD if it is
present, and this could lead to an incorrect authentication boot flow.
Signed-off-by: Breno Lima <breno.lima@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
OSC_27M_CLK should return 27MHz and OSC_32K_CLK should return
32768Hz to reflect the reality.
This also keeps the values in sync with the Linux clock tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The CPU banner printed is as following:
CPU: CPU: Freescale i.MX8QXP RevB A35 at 147228 MHz
1. Drop the CPU:
2. Change vendor from Freescale to NXP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current value CTLUPD_AREF(0) is the reset value of the register,
so there is no need to write a value. If needed, the register can be
written using board specific CR settings.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
