Add a set_voltage() function which handles the switch from 3.3V to 1.8V
for SD card UHS modes.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With commit 38d6b7ebda ("spl: Drop bd_info in the data section") you
need to enable this option to boot from mmc.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
The K3 R5F remoteproc driver in U-Boot was upstreamed prior to the
equivalent remoteproc driver in the Linux kernel. Some of the DT
properties used in U-Boot got upstreamed using different names
in Linux kernel.
The modified property names include the R5F cluster mode configuration
property "lockstep-mode"; and three different individual R5F core config
properties - "atcm-enable", "btcm-enable" and "loczrama". The property
names were updated as follows:
lockstep-mode => ti,cluster-mode
atcm-enable => ti,atcm-enable
btcm-enable => ti,btcm-enable
loczrama => ti,loczrama
Update the K3 R5F remoteproc driver, the corresponding binding, and
all the existing usage in AM65x, J721E and J7200 dts files all at
once to use the new properties and to not break any bisectability.
Signed-off-by: Suman Anna <s-anna@ti.com>
AM65x SoC has two USB subsystems and their corresponding device tree nodes
have the same name but different path. While allocating sequence numbers
for these device tree nodes using alias, phandles can be used to
distinguish them.
Enable config for phandle check while getting sequence number to
distinguish the USB device tree nodes.
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This disables booting to non-Linux OSes.
This board is uncomfortably close to its 256K size limit, so every
few KB saved helps.
Signed-off-by: David Lechner <david@lechnology.com>
This disables the CONFIG_NET setting for LEGO MINDSTORMS EV3. This board
does not have any built-in networking, so it does not make sense to
enable this feature.
This also fixes the warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: David Lechner <david@lechnology.com>
This drops assigning bi_arch_number on LEGO MINDSTORMS EV3. This board
never had its own unique number and since we are using device tree,
we no longer need to pass an arch number to Linux.
Signed-off-by: David Lechner <david@lechnology.com>
This sets the serial# environmet variable instead of using ATAGs on
LEGO MINDSTORMS EV3.
Also fix some nomenclature while we are touching this code (Bluetooth
address is not the same as MAC address, EEPROM version is not the same
as board version).
Signed-off-by: David Lechner <david@lechnology.com>
Move twl4030_power_mmc_init() from board_mmc_power_init() to misc_init_r()
and disable CONFIG_SYS_MALLOC_F. Otherwise U-Boot cannot initialize MMC.
Also disable CONFIG_CMD_SLEEP CONFIG_DM_DEVICE_REMOVE CONFIG_MMC_VERBOSE to
free some space.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Commit dd5c954e91 ("travis/gitlab/azure: Use -W to avoid warnings check")
added -W to avoid warnings check, but it mistakenly dropped -E for
the world build script in the azure pipelines.
This caused builds on the azure pipelines fail to report warnings. Let's
add it back.
Fixes: dd5c954e91 ("travis/gitlab/azure: Use -W to avoid warnings check")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The implementation of pytest_runtest_protocol() must call
pytest_runtest_logstart() and pytest_runtest_logfinish(). This appears to
be necessary even in pytest 5.2.1 judging by the default version of
pytest_runtest_protocol(), but evidently some form of code reorganization
in pytest only made this have a practical effect in the newer version. I'd
previously been under the impression that 100% of the required work of
pytest_runtest_protocol() was handled by the fact it called
runtestprotocol() as its implementation. However, it appears that custom
implementations do need to do a little more than this.
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add myself as co maintainer to network subsystem
Acked-by: Tom Rini <trini@konsulko.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fixes issues when switching from GPT to MBR partition tables.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Config allows to disable printing contents of fitImage to optimize boottime.
Signed-off-by: Ravik Hasija <rahasij@linux.microsoft.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The load command should not silently return to the console prompt if an
invalid block device is specified and no file is loaded.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
No version information is used in armv8/fwcall.c therefore do not include
version.h header file. This change prevents recompiling fwcall.o when
SOURCE_DATE_EPOCH changes.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
- Fix CMD_ACPI dependency in Kconfig
- Correct overflow in __udelay() in TSC timer driver
- Add a devicetree node for eMMC for Coral
- Minor improvements on image loading
- Reduce size of Samus image
With the recent addition of ACPI generation, the image size has got beyond
its current limit.
Samus does not actually use this, nor x86 emulation for PCI ROMs, so
disable both features.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enhance the debugging to show the next stage being booted as well as a
dump of the start of the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This should be done even if not using TPL, since BSS may be in use or
boards that only use SPL. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present if the command line is very long it is truncated by the
printf() statement, which works within a limited buffer. Use puts()
instead. Also show better debugging with the command-line setup
fails.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present it is possible to dump an image within the zimage command, but
it is also useful to be able to dump it from elsewhere, for example in a
loader that has special handling for the different zimage stages.
Export this feature as a new function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The Global Non-Volatile Storage struct has some fields with particular
meanings. Rename these to make things easier to follow. Also add a few
more boot flags.
GNVS should not be confused with GNVQ (Going Nowhere Very Quickly).
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present BSS is always placed in SDRAM. If a separate BSS is not in use
this means that BSS doesn't work as expected. Make the setting conditional
on the SEPARATE_BSS option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The part of U-Boot that actually ends up in u-boot-nodtb.bin is not built
with any particular alignment. It ends at the start of the BSS section.
The BSS section selects its own alignment, which may larger.
This means that there can be a gap of a few bytes between the image
ending and BSS starting.
Since u-boot.bin is build by joining u-boot-nodtb.bin and u-boot.dtb (with
perhaps some padding for BSS), the expected result is not obtained. U-Boot
uses the end of BSS to find the devicetree, so this means that it cannot
be found.
Add 32-byte alignment of BSS so that the image size is correct and
appending the devicetree will place it at the end of BSS.
Example SPL output without this patch:
Sections:
Idx Name Size VMA LMA File off Algn
0 .text 000142a1 fef40000 fef40000 00001000 2**4
CONTENTS, ALLOC, LOAD, RELOC, READONLY, CODE
1 .u_boot_list 000014a4 fef542a8 fef542a8 000152a8 2**3
CONTENTS, ALLOC, LOAD, RELOC, DATA
2 .rodata 0000599c fef55760 fef55760 00016760 2**5
CONTENTS, ALLOC, LOAD, RELOC, READONLY, DATA
3 .data 00000970 fef5b100 fef5b100 0001c100 2**5
CONTENTS, ALLOC, LOAD, RELOC, DATA
4 .binman_sym_table 00000020 fef5ba70 fef5ba70 0001ca70 2**2
CONTENTS, ALLOC, LOAD, DATA
5 .bss 00000060 fef5baa0 fef5baa0 00000000 2**5
ALLOC
You can see that .bss is aligned to 2**5 (32 bytes). This is because of
the mallinfo struct in dlmalloc.c:
17 .bss.current_mallinfo 00000028 00000000 00000000 000004c0 2**5
ALLOC
In this case the size of u-boot-spl-nodtb.bin is 0x1ba90. This matches up
with the _image_binary_end symbol:
fef5ba90 g .binman_sym_table 00000000 _image_binary_end
But BSS starts 16 bytes later, at 0xfef5baa0, due to the 32-byte
alignment. So we must align _image_binary_end to a 32-byte boundary. This
forces the binary size to be 0x1baa0, i.e. ending at the start of bss, as
expected.
Note that gcc reports __BIGGEST_ALIGNMENT__ of 16 on this build, even
though it generates an object file with a member that requests 32-byte
alignment.
The current_mallinfo struct is 40 bytes in size. Increasing the struct to
68 bytes (i.e. just above a 64-byte boundary) does not cause the alignment
to go above 32 bytes. So it seems that 32 bytes is the maximum alignment
at present.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: add more details in the commit message to help people understand]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Move to log_debug() and make use of the new SPL function to find the
text base.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useful to know the TEXT_BASE value for the image being loaded in
TPL/SPL. Add a new spl_get_image_text_base() function to handle this.
Make use of this in the x86 SPL handler, instead of having the logic
there.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Use a driver name in line with the compatible string so that of-platdata
can use this driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Some comments were provided after this patch was applied. Address them.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add a node for this so we can indicate that it is does not require any
ACPI code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present long delays such as msleep(2000) can cause an overflow in this
function. There is no need for this, since it already uses a 64-bit int.
Add a cast to correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Trying to compile qemu-x86_64_defconfig with CONFIG_CMD_ACPI=y and
CONFIG_ACPIGEN=n fails with
ld.bfd: cmd/built-in.o: in function `do_acpi_items':
cmd/acpi.c:162: undefined reference to `acpi_dump_items'
Add the missing configuration dependency.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
It is useless and misleading to print the ret variable that is not set
by the dev_read_addr routine. Also, move the '\n' character after the
round bracket that contains the error code.
Signed-off-by: Dario Binacchi <dariobin@libero.it>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
With the fixes to the sun8i-emac driver, we can now enable Ethernet
support on the OrangePi Zero2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
The pinmux choice for the RMII/RGMII pins the EMAC is connected to is
not dependent on the EMAC IP, but on the SoC it is integrated in.
Deriving the pinmux from the DT compatible string (as we do at the
moment) will thus cause problems with certain EMAC IP / SoC combinations.
To avoid this exact issue with the H616, let's use our Kconfig MACH
symbols to choose the correct pinmux setup.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
At the moment we only consider the EPHY register for those SoCs were
we actually have an internal PHY to configure. However even other SoCs
have this register, an expect the EPHY select bit to be cleared for
proper operation with an external PHY.
Rework sun8i_emac_set_syscon_ephy() to be called regardless of the EMAC
model, and clear the H3_EPHY_SELECT bit if no internal PHY is used.
We get away without it so far because SoCs like the A64 clear this bit
on reset, but we need to explicitly clear it on the H616, for instance.
The Linux driver does so as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmAV6K8RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYERgf/QbwOL87yPbf9SyXBQ0EMTmn1ve9HCiv9
yeXrijvA0/wtTVoM44d/z7THb+7Zqw6LbsVOXUSicdGqaogy10xIuz5we0CoGJm6
iwYWV6kaAqjCxDTlSToGnR/TCjiOVgXC6u5QPCZC0LGbAmDbAl4jyCuQxxq2eXYD
hrLSzZPHDe0s2BeWZKRQJ26qyPfWIribXNJXG78/FsvDrdWPPc5K+/ZEb2IWawWR
nEZ8GTEYZpik/niEJ3gFozwCwpJQi3PyukjZvzTGn6tBqg12YXE4dbSzcj48Uj4o
prwUFAGKRR97zFB6c4+NUvd3VBUgPtPdZrtzZ1nNCppiMq1E4BKiDg==
=kijh
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-30jan21' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
tpm fixes for coral
binman fixes support for symbols in sub-sections
support for additional cros_ec commands
various minor fixes / tweaks
As we need standard usb_ep's desc, so set it when enable ep.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Change to use wMaxPacketSize of current speed EP desc for request
length wrap up.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Remove the gadget driver speed check, and set its max_speed to
be USB_SPEED_HIGH.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If one of functions is not super speed capable, we need force the udc
to be high speed, this is an equivalent implementation of
usb_gadget_udc_set_speed() in kernel but simple, which set the gadget
max_speed to be high speed, so afterwards when start gadget duc can
set the HW to be USB 2.0 mode.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Set its max_speed to be super speed.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add super speed EP config.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This patch is to add usb gadget super speed support in common
driver, including BOS descriptor and select the super speed
descriptor from function driver.
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Tested-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
