The current pmic i2c code assumes the current i2c bus is
the same as the pmic device's bus. There is nothing ensuring
that to be true. Therefore, select the proper bus before performing
a transaction.
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This adds driver support for the TPS65090 PMU. Support includes
hooking into the pmic infrastructure so that the pmic commands
can be used on the console. The TPS65090 supports the following
functionality:
- fet enable/disable/querying
- getting and setting of charge state
Even though it is connected to the pmic infrastructure it does
not hook into the pmic charging charging infrastructure.
The device tree binding is from Linux, but only a small subset of
functionality is supported.
Signed-off-by: Tom Wai-Hong Tam <waihong@chromium.org>
Signed-off-by: Hatim Ali <hatim.rv@samsung.com>
Signed-off-by: Katie Roberts-Hoffman <katierh@chromium.org>
Signed-off-by: Rong Chang <rongchang@chromium.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Signed-off-by: Aaron Durbin <adurbin@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This enum should be common across all PMICs rather than having it
independently defined with the same name in multiple places.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Commit be3b51aa did this mostly, but several have been added since. Do the
job again.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We need check the NULL pointer as at91_pio_get_port() may return NULL.
Also print a error message when at91_pio_get_port() failed otherwise we
cannot notice the failure.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The correct value for this setting can vary across SoCs and boards, so make it
configurable.
Also reduce the default value to 8, which is the same default as used in the
Linux driver.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
On Thu, 2014-05-08 at 22:26 +0100, Ian Campbell wrote:
> The {r,t}xbuffs fields also need to be aligned. Previously this was done
> implicitly because they immediately followed the descriptor tables. Make this
> explicit and also move to the head of the struct.
Looks like I managed to not actually commit the move of the field to the
head of the struct! v3.1 follows....
Ian.
8<------------
>From 2937ba01841887317f6792709ed57cb86b5fc0cd Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Thu, 1 May 2014 19:45:15 +0100
Subject: [PATCH] net/designware: reorder struct dw_eth_dev to pack more
efficiently.
The {tx,rx}_mac_descrtable fields are aligned to ARCH_DMA_MINALIGN, which could
be 256 or even larger. That means there is a potentially huge hole in the
struct before those fields, so move them to the front where they are better
packed.
Moving them to the front also helps ensure that so long as dw_eth_dev is
properly aligned (which it is since "net/designware: ensure device private data
is DMA aligned.") the {tx,rx}_mac_descrtable will be too, or at least avoids
having to worry too much about compiler specifics.
The {r,t}xbuffs fields also need to be aligned. Previously this was done
implicitly because they immediately followed the descriptor tables. Make this
explicit and also move to the head of the struct.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
Tested-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
Reviewed-by: Siarhei Siamashka <siarhei.siamashka@gmail.com>
This is required at least on ARM.
When sending instead of simply invalidating the entire descriptor, flush
as little as possible while still respecting ARCH_DMA_MINALIGN, as
requested by Alexey.
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: Alexey Brodkin <abrodkin@synopsys.com>
struct dw_eth_dev contains fields which are accessed via DMA, so make sure it
is aligned to a dma boundary. Without this I see:
ERROR: v7_dcache_inval_range - start address is not aligned - 0x7fb677e0
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Marek Vasut <marex@denx.de>
On Mon, 2014-05-05 at 14:18 +0200, Stefan Roese wrote:
> > + case 1:
> > +#if CONFIG_MMC1_PG
> Are you sure that this is correct and shouldn't be:
>
> +#ifdef CONFIG_MMC1_PG
>
> ?
It's "correct" in so far as it works (the boards.cfg config stuff
#defines things to 1), but I think you are right that it isn't the
preferred style. But...
> A quick scan through this patch series shows that this define
> is not set at all. Perhaps its outdated? Or is it used to support
> some other sunxi SoC? Not sure, perhaps it should be removed for
> now.
...I had thought that it was to support some other board which wasn't
being upstreamed right now, so eventually useful and harmless for now,
but I've just checked and it isn't actually used by any of the boards in
u-boot-sunxi.git. So rather than fix it to use #ifdef lets drop it.
Rather than resend the entire series, here is v5.1 of this patch.
> Other than this please add my:
>
> Reviewed-by: Stefan Roese <sr@denx.de>
Thanks!
8<---------------------------------
>From 20704e35a41664de5f516ed0e02981ac06085102 Mon Sep 17 00:00:00 2001
From: Ian Campbell <ijc@hellion.org.uk>
Date: Fri, 7 Mar 2014 04:29:39 +0000
Subject: [PATCH v5.1 7/8] sunxi: mmc support
This adds support for the MMC controller on the Allwinner A20 (sun7i)
processor.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Luke Leighton <lkcl@lkcl.net>
Signed-off-by: Oliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Wills Wang <wills.wang.open@gmail.com>
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Cc: Tom Cubie <Mr.hipboi@gmail.com>
Cc: Aaron Maoye <leafy.myeh@allwinnertech.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: Tom Rini <trini@ti.com>
In 7168977 we made calls to check_and_invalidate_dcache_range()
conditional on !CONFIG_SYS_FSL_ESDHC_USE_PIO. Only define this function
in this case as well.
Signed-off-by: Tom Rini <trini@ti.com>
This enables specifying which eMMC HW partition to target for any U-Boot
command that uses the generic get_partition() function to parse its
command-line arguments.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds functions for read, write and authentication
key programming for the Replay Protected Memory Block partition
in the eMMC.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Pierre Aubert <p.aubert@staubli.com>
MMC switch command for unsupported feature (e.g. bus width) sets a switch
error bit in card status. This bit should be checked, and, if it's set,
no access with new controller settings should be performed.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
When configure the fsl_esdhc driver to PIO mode by defining
"CONFIG_SYS_FSL_ESDHC_USE_PIO", the SD/MMC read and write will fail.
Two bugs in the driver to cause the issue:
1. The read buffer was invalidated after reading from DATAPORT register,
which should be only applied to DMA mode. The valid data in cache was
overwritten by physical memory.
2. The watermarks are not set in PIO mode, will cause according state not
be set.
Acked-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Signed-off-by: Ye.Li <B37916@freescale.com>
Do not do partial bitstream detection based on bitstream
size and use bitstream_type argument which is passed
from the fpga core.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Clean up partial, full and compressed bitstream handling.
U-Boot supports full bitstream loading and partial
based on detection which is not 100% correct.
Extending fpga_load/fpga_loadbitstream() with one more
argument which stores bitstream type.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Conflicts:
boards.cfg
Conflicts were trivial once u-boot-arm/master boards.cfg was
reformatted (commit 6130c146) to match u-boot/master's own
reformatting (commit 1b37fa83).
Define and use CONTROL_REGISTER_W1C_MASK to make sure that
w1c bits of usb control register do not get reset while
writing any other bit
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support for VSC8664 PHY module which can
be found on Freescale's T4240RDB boards.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
To reuse the code, added the s5p_sdhci_core_init function.
Before applied this patch, didn't use the 8-bit mode at exynos baord.
Because it didn't set "MMC_MODE_8BIT".
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Restore the platdata(property of dt) into host struct.
Then data's information is maintained and reused anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Before this patch it was only possible to access the default eMMC HW
partition. By partition selection I mean the access to eMMC via the
ext_csd[179] register programming.
It sometimes happens that it is necessary to write to other partitions.
This patch adds extra attribute to "raw" sub type of the dfu_alt_info
environment variable (e.g. boot-mmc.bin raw 0x0 0x200 mmcpart 1;)
It saves the original boot value and restores it after storing the file.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Since dfu_flush() can write raw data, dfu_write() with zero size
can be removed from download_tail() in thor gadget.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
Before dfu write and flush operations separation,
dfu write data was flushed by host download request
with len of zero size.
Since above change manually calling dfu write with zero
size has non sense (e.g. in THOR). This should be done by
flush operation.
So now dfu_write_buffer_drain() is called in dfu_flush().
If there is any raw data to flush (like it can be in thor)
then it will be physically written to medium.
Signed-off-by: Przemyslaw Marczak <p.marczak@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Marek Vasut <marex@denx.de>
ci_udc only allocates a single QTD structure per EP. All data needs to be
extracted from the DTD prior to calling ci_ep_submit_next_request(), since
that fills the QTD with next transaction's parameters. Fix
handle_ep_complete() to extract the transaction (remaining) length before
kicking off the next transaction.
In practice, this only causes writes to UMS devices to fail for me. I may
have tested the final versions of my previous ci_udc patch only with
reads. More recently, I had patches applied locally that allocated a QTD
per USB request rather than per USB EP, although since that doesn't give
any performance benefit, I'm dropping those.
Fixes: 2813006fec ("usb: ci_udc: allow multiple buffer allocs per ep")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A few changes are made to the Tegra EHCI driver so that it can set
everything up for device-mode operation on the first USB controller.
This can be used in conjunction with ci_udc.c to operate as a USB
device.
Detailed changes are:
* Rename set_host_mode() to set_up_vbus() since that's really what it
does.
* Modify set_up_vbus() to know whether it's initializing in host or
device mode, and:
- Skip the external VBUS check in device mode, since external VBUS is
expected in this case.
- Disable VBUS output in device mode.
* Modify init_phy_mux() to know whether it's initializing in host or
device mode, and hence skip setting USBMODE_CM_HC (which enables host
mode) in device mode. See the comments in that function for why this
is safe w.r.t. the ordering requirements of PHY selection.
* Modify init_utmi_usb_controller() to force "b session valid" in device
mode, since the HW requires this. This is done in UTMI-specific code,
since we only support device mode on the first USB controller, and that
controller can only talk to a UTMI PHY.
* Enhance ehci_hcd_init() to error-check the requested host-/device-mode
vs. the dr_mode (dual-role mode) value present in device tree, and the
HW configurations which support device mode.
* Enhance ehci_hcd_init() not to skip HW initialization when switching
between host and device mode on a controller. This requires remembering
which mode the last initialization used.
Cc: Jim Lin <jilin@nvidia.com>
Cc: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
