If the other side isn't listening, we should reset the state to ignore
the whole message and not just the part we missed. This makes it easier
to connect at any time to the jtag console without worrying about the two
sides getting out of sync and thus sending garbage back and forth.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Lots of code use this construct:
cmd_usage(cmdtp);
return 1;
Change cmd_usage() let it return 1 - then we can replace all these
ocurrances by
return cmd_usage(cmdtp);
This fixes a few places with incorrect return code handling, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds the "ecctest" command to test and simulate ECC errors
(single bit and/or double bit) while running from SDRAM. Currently only
the IBM DDR2 controller is supported (405EX, 440SP(e), 460EX/GT).
This is done by copying and calling functions, modifying the SDRAM
controller operation mode, in internal SRAM/OCM.
For correctable ECC errors (single bit) only the status will be printed
since the DDR2 controller doesn't provide the faulting address:
=> ecctest 1000000 1
Using address 01000000 for 1 bit ECC error injection
ECC: Correctable error
Uncorrectable ECC errors (double bit) will also display the faulting
address:
=> ecctest 1000000 2
Using address 01000000 for 2 bit ECC error injection
ECC: Uncorrectable error at 0x0001000000
To enable this "ecctest" function you need to define CONFIG_CMD_ECCTEST
in the board config header.
Tested on katmai and t3corp.
Signed-off-by: Stefan Roese <sr@denx.de>
Use the correct macro instead of the hardcoded 0x4c to clear the ECC
status in the 440/460 DDR(2) error status register after ECC
initialization.
Also the non-440 parts (405EX(r) right now) and the IBM DDR PPC variants
(440GX) use a different registers to clear this error status. Use the
correct ones.
Signed-off-by: Stefan Roese <sr@denx.de>
Make sure that some SDRAM/DDR2 registers are only defined for the PPC
variants really implementing those registers.
Signed-off-by: Stefan Roese <sr@denx.de>
Using this define, a board can define an opimized RFDC value and use
the auto calibration code to "tune" the remaining DDR2 controller
calibration register.
Signed-off-by: Stefan Roese <sr@denx.de>
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move serdes init until after we are in ram so we can keep track of a
global static protocal map for the particular serdes config we are in.
This makes is_serdes_configured() much simplier and not constantly
reading registers to determine if a given device is enabled based on the
protocol.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p3041 to cpu_type_list and SVR list
* Added number of LAWs for p3041
* Set CONFIG_MAX_CPUS to 4 for p3041
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are various locations that we have chip specific info:
* Makefile for which ddr code to build
* Added p5020 & p5010 to cpu_type_list and SVR list
* Added number of LAWs for p5020
* Set CONFIG_MAX_CPUS to 2 for p5020
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The user manual refers to FMAN1 and FMAN2 not 0 and 1.
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On QorIQ CoreNet based devices we have a global clocking block. We want
to keep track of SYSCLK frequency as it is what is used to derive all
other frequencies in the SoC
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move to using fdt_node_offset_by_compat_reg to find the node offsets we
want to update instead of using aliases.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we used an alias the pci node to determine which node to
fixup or delete. Now we use the new fdt_node_offset_by_compat_reg to
find the node to update.
Additionally, we replace the code in each board with a single macro call
that makes assumes uniform naming and reduces duplication in this area.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove dupliacted setting of PCI/PCIe address and offsets in board
config.h. Renamed CONFIG_SYS_PCI1/2_ADDR to CONFIG_SYS_PCI1/2ADDR on
MPC8641 boards since its really PCIE controllers and not PCI.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The board maintainer states:
The GTH board is obsolete and has not been manufactured for
several years.
To my knowledge, no recent U-Boot build has been tested on that
card.
So drop support for this board.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Thomas Lange <thomas@corelatus.se>
Acked-by: Thomas Lange<thomas@corelatus.se>
The code to map SERDES configs to slot names is board specific and not
chip specific. Thus it should live in board/freescale/p1022ds/ and not
in arch/powerpc/cpu/.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 'errata' command to report what errata we workaround. Report
workaround for erratum SATA-A001 on P1022/P1013.
Also sorted the CONFIG_CMD_* list.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Specifics:
1) 36-bit only
2) Booting from NOR flash only
3) Environment stored in NOR flash only
4) No SPI support
5) No DIU support
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the LAW target (enum law_trgt_if) to the fsl_pci_info structure, so that
we can capture the LAW target for a given PCI or PCIE controller. Also update
the SET_STD_PCI_INFO and SET_STD_PCIE_INFO macros to assign the
LAW_TRGT_IF_PCI[E]_x macro to the LAW target field of the structure.
This will allow future PCI[E] code to configure the LAW target automatically,
rather than requiring each board to it for each PCI controller separately.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The e5500 has a link register stack and segment target address cache.
Its safe to enable these bits on older e500 cores as the bits are
implemented in the register.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Each platform had its own version of the upmconfig, despite the
init process being identical. Now that we have a spot for common
lbc code, create a common upmconfig() there.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The new command dumps the TLBCAM, the LAWs, and the BR/OR regs.
Add CONFIG_CMD_REGINFO to the config for all MPC85xx parts.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current code redefines functions based on FSL_CORENET_ vs not -
create macros/inlines instead that hide the differences.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This dumps out the contents of TLB1 on 85xx-based systems.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Extract the operation to read a tlb into a function - we will need
this later to print out the tlbs, and there's no point in duplicating
the code. Create a TSIZE_TO_BYTES macro to deal with the conversion
from the MAS field to an actual size instead of duplicating this in code.
There are a few misc other minor cleanups.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Currently, 83xx, 86xx, and 85xx have a lot of duplicated code
dedicated to defining and manipulating the LBC registers. Merge
this into a single spot.
To do this, we have to decide on a common name for the data structure
that holds the lbc registers - it will now be known as fsl_lbc_t, and we
adopt a common name for the immap layouts that include the lbc - this was
previously known as either im_lbc or lbus; use the former.
In addition, create accessors for the BR/OR regs that use in/out_be32
and use those instead of the mismash of access methods currently in play.
I have done a successful ppc build all and tested a board or two from
each processor family.
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We may have cpu-handles pointing to the cpu nodes we delete. If so we
should delete the handles as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_FSL_SEC_COMPAT is set to 2 for the SEC 2.x and SEC 3.x.
Parts with newer SEC h/w versions will increment the number to
accomodate incompatible code changes.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds a gpmc_init function for OMAP4 and adds calls to
gpmc_init for existing OMAP4 boards: panda and sdp4430
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds macros for the following purposes:
- GPIO configuration
- SDRAM configuration
- Wakeup
- Clock configuration
- Interrupt controller configuration
These macros are intended to replace numerous copies of the same code.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
The L1 regions of Core B are not directly accessible from Core A, so we
need to use DMA to get at them.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Use the new portmux framework to handle the details when possible.
Unfortunately, we cannot yet use this in the standalone initialization
logic, so we need to keep around the old portmux writes for now.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add definitions and initialization in orion5x for mvgbe.
Add orion5x in mvgbe SoC includes.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Rename all references to kirkwood in mvgbe symbols
throughout the whole codebase.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
This patch adds fdt support to boot linux, followed Michal's
work on microblaze.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
Follow the discussion of Charles Manning and Mike Frysinger.
Using gc_sections helps reduce image size.
Configuring for nios2-generic board...
Before,
text data bss dec hex filename
123979 3724 22892 150595 24c43 /tmp/u-boot/u-boot
After,
text data bss dec hex filename
115983 3800 22732 142515 22cb3 /tmp/u-boot/u-boot
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch adds basic support for Freescale MPC8308 CPU. Serial ports,
NOR flash and integrated Ethernet controllers are supported.
PCI Express is also supported. eSDHC, NAND and USB may work but aren't
tested (using ULPI PHY requires additional patch).
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch modifies the omap24xx driver so that it will also work with OMAP4.
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The architecture independent header is moved to drivers/mmc, and the architecture
dependent headers reside in asm/arch-omap3 and asm/arch-omap4
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds minimum support for OMAP4. Code which can be shared
between OMAP3 and OMAP4 is placed in arch/arm/cpu/armv7/omap-common
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The purpose of this patch is to prepare for adding the OMAP4 architecture, which is Cortex A9
Cortex A8 and A9 both belong to the armv7 architecture, hence the name change.
The two architectures are similar enough that substantial code can be shared.
Signed-off-by: Aneesh V <aneesh@ti.com>
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the second and third mmc channels on OMAP3
processors
Boards wishing to use this feature should define CONFIG_SYS_MMC_SET_DEV
in the board config
Tested on Overo
Signed-off-by: Steve Sakoman <steve@sakoman.com>
Tested-by: Philip Balister <philip@opensdr.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Now that we have a unified gpio layer, the misc partial gpio commands
can be unified and made complete (support all possible gpios).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The current pinmux handling has spread throughout Blackfin drivers and
board code and is getting hideous to maintain. So import the gpio and
portmux layer from the Blackfin Linux code. This should spur a serious
of cleanups across the Blackfin tree.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Older on-chip Blackfin bootroms do not create a dummy NMI handler, so set
up one ourselves when anomaly 05000219 applies.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The default storage location for bootcount is EVT0. This version uses
one 32bit value and combines the magic/count value in the upper/lower
16bits. If there is demand for more, should be easy to do.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Avoid banging on the trace MMRs when debugging is disabled, avoid calling
the funcs multiple times in a row, disable the trace buffer earlier in the
exception handler to avoid eating more user entries, and dump the buffer
before calling the kgdb hook. This way we maximize useful debugging info
up front rather than needing external tools (like gdb/serial/etc...).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The hush shell dynamically allocates (and re-allocates) memory for the
argument strings in the "char *argv[]" argument vector passed to
commands. Any code that modifies these pointers will cause serious
corruption of the malloc data structures and crash U-Boot, so make
sure the compiler can check that no such modifications are being done
by changing the code into "char * const argv[]".
This modification is the result of debugging a strange crash caused
after adding a new command, which used the following argument
processing code which has been working perfectly fine in all Unix
systems since version 6 - but not so in U-Boot:
int main (int argc, char **argv)
{
while (--argc > 0 && **++argv == '-') {
/* ====> */ while (*++*argv) {
switch (**argv) {
case 'd':
debug++;
break;
...
default:
usage ();
}
}
}
...
}
The line marked "====>" will corrupt the malloc data structures and
usually cause U-Boot to crash when the next command gets executed by
the shell. With the modification, the compiler will prevent this with
an
error: increment of read-only location '*argv'
N.B.: The code above can be trivially rewritten like this:
while (--argc > 0 && **++argv == '-') {
char *arg = *argv;
while (*++arg) {
switch (*arg) {
...
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Background Info:
Some PPC440/460 boards have caches enabled in the Boot/FLASH TLB (via
init.S) to speed up the boot process. In relocate_code (start.S) the
cache inhibit attribute for this TLB is set to disable cache. This is
needed for the CFI FLASH driver.
This patch now cleans this code up:
- CONFIG_SYS_TLB_FOR_BOOT_FLASH is defined to 0 (default TLB) if not
defined in the top of this file. This way, we can remove an ugly
#ifdef in this code.
- Replace complex "#if defined(CONFIG_440EP) || defined(CONFIG_GR)..."
statement with "#if defined(CONFIG_440)".
- Remove unnecessary cache invalidate calls resulting in faster bootup.
Signed-off-by: Stefan Roese <sr@denx.de>
As described in item #10 of the SDRAM initialization (chapter 22.2.9
of the PPC460EX/EXr/GT users manual), RDSS may need to be adjusted. The
code for this is now factored out and executed for non-SPD based boards
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch makes it possible to overwrite the default auto-calibration
scan window (SDRAM_WRDTR.[WDTR], SDRAM_CLKTR.[CKTR] values) with
board specific values. The parameters of the weak default function are
corrected as well. This way we don't need the casts any more.
This feature will be used by an upcoming PPC460GT board port.
Signed-off-by: Stefan Roese <sr@denx.de>
By not defining CONFIG_SYS_PCI_MASTER_INIT and CONFIG_SYS_PCI_TARGET_INIT,
PCI support (host and adapter) will not be enabled. But it's still
possible to use the U-Boot PCI infrastructure for the PCIe ports.
This configuration option is needed for a new 460GT board, which uses
PCIe but has PCI disabled.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables booting with option E on the PPC460EX/EXr/GT.
When booting with Option E, the PLL is in bypass, CPR0_PLLC[ENG]=0.
The Software Boot Configuration Procedure is needed to engage the
PLL and perform a chip reset.
Signed-off-by: Stefan Roese <sr@denx.de>
Add USB OHCI support for at91sam9g45ekes/at91sam9m10g45ek boards.
Note that according to errata from Atmel, OHCI is not operational
on the first revision of at91sam9g45 chip. So this patch enables
OHCI support for later revisions.
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
This patch fixes following error:
zlib.c:31:27: error: asm/unaligned.h: No such file or directory
Suggested-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andreas Biemann <biessmann@corscience.de>
Due to a hardware bug mentioned in latest AP7000 datasheet errata
(revision M from 09.09) branch folding is unreliable.
This patch disables CPUCR.FE bitfield as stated in datasheet.
Signed-off-by: Andreas Biemann <biessmann@corscience.de>
Currently the U-Boot address ranges for AVR32 boards are
printed like this:
"U-Boot code: (null) -> 0001183c data: 000188e8 -> 0004e9b0"
This patch fixes this to print:
"U-Boot code: 00000000 -> 0001183c data: 000188f8 -> 0004e9c0"
Signed-off-by: Reinhard Meyer <info@emk-elektronik.de>
Commit 460c2ce3 "MPC5200: workaround data corruption for unaligned
local bus accesses" fixed the problem for MPC5200 only, but MPC512x is
affected as well, so apply the same fix here, too.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
This add support cpu reset by trigger_address_error function.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This changes path of irqflags.h from linux/ to asm/.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The AmigaOneG3SE board has been orphaned or a very long time, and
broken for more than 12 releases resp. more than 3 years. As nobody
seems to be interested any more in this stuff we may as well ged rid
of it, especially as it clutters many areas of the code so it is a
continuous pain for all kinds of ongoing work.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_SYS_BUS_HZ has not really been used anywhere except to be
redined as CONFIG_SYS_BUS_CLK; in addition, the mpc7448hpc2 had the
bogus CONFIG_SYS_CONFIG_BUS_CLK setting which duplicated the
funtionality. Change all this to use CONFIG_SYS_BUS_CLK consistently.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Frank Gottschling <fgottschling@eltec.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Cc: Eran Man <eran@nbase.co.il>
Cc: Stefan Roese <sr@denx.de>
Cc: Nye Liu <nyet@zumanetworks.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
The MPC5200 has a nasty problem that will cause silent data corruption
when performing unaligned 16 or 32 byte accesses when reading from the
local bus - typically this affects reading from flash. The problem can
be easily shown:
=> md fc0c0000 10
fc0c0000: 323e4337 01626f6f 74636d64 3d72756e 2>C7.bootcmd=run
fc0c0010: 206e6574 5f6e6673 00626f6f 7464656c net_nfs.bootdel
fc0c0020: 61793d35 00626175 64726174 653d3131 ay=5.baudrate=11
fc0c0030: 35323030 00707265 626f6f74 3d656368 5200.preboot=ech
=> md fc0c0001 10
fc0c0001: 65636801 00000074 0000003d 00000020 ech....t...=...
fc0c0011: 0000005f 00000000 00000074 00000061 ..._.......t...a
fc0c0021: 00000000 00000064 00000065 00000035 .......d...e...5
fc0c0031: 00000000 00000062 0000003d 0000006f .......b...=...o
=> md.w fc0c0001 10
fc0c0001: 0000 3701 0000 6f74 0000 643d 0000 6e20 ..7...ot..d=..n
fc0c0011: 0000 745f 0000 7300 0000 6f74 0000 6c61 ..t_..s...ot..la
This commit implements a workaround at least for the most blatant
problem: using memcpy() from NOR flash. We rename the assembler
routine into __memcpy() and provide a wrapper, which will use a
byte-wise copy loop for unaligned source or target addresses when
reading from NOR flash, and branch to the optimized __memcpy()
in all other cases, thus minimizing the performance impact.
Tested on lite5200b and TQM5200S.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
ATAG_VIDEOLFB is not used anywhere.
The belowing warning is occurred due to this ATAG.
[ 0.000000] Ignoring unrecognised tag 0x54410008
This patch fixed it.
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Martin Krause <Martin.Krause@tqs.de>
The ARM ABI requires that the stack be aligned to 8 bytes as it is noted
in Procedure Call Standard for the ARM Architecture:
http://infocenter.arm.com/help/topic/com.arm.doc.ihi0042d/index.html
Unaligned SP also causes the problem with variable-length arrays
allocation when VLA address becomes less than stack pointer during
aligning of this address, so the next 'push' in the stack overwrites
first 4 bytes of VLA.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Tested on tx25(mx25), imx27lite(mx27), qong(mx31) and trab(s3c2400)
Tested-by: Wolfgang Denk <wd@denx.de>
Currently EMAC_MDIO_PHY_NUM is defined as 1 in emac_defs.h.
Because of this, EMAC does not work on EVMs which do not have phy
connected at 1. Moving the macro to board config file makes this
configurable depending on where the phy is connected on the MDIO bus.
This patch fixes the board reset issue observed during network access
on DM365EVM. EMAC driver was assuming EMAC_MDIO_PHY_NUM as 1
but it is 0 on DM365EVM.
This patch is verified on da830/omap-l137, dm365 and dm644x evms.
Signed-off-by: Prakash PM <prakash.pm@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The push / pop instructions used in this file are available only with
more recent tool chains:
cache.S: Assembler messages:
cache.S:133: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:160: Error: bad instruction `pop {r1,r2,r3,pc}'
cache.S:164: Error: bad instruction `push {r0,r1,r2,lr}'
cache.S:191: Error: bad instruction `pop {r1,r2,r3,pc}'
Change push/pop into stmfd/ldmfd instructions to support older
versions of binutils as well.
I verified that the modified source code generates exactly the same
binary code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Sandeep Paulraj <s-paulraj@ti.com>
Cc: Tom Rix <tom@bumblecow.com>
Conflicts:
CONFLICT (rename/add): Rename
board/davinci/da830evm/Makefile->board/ti/tnetv107xevm/Makefile
in 89b765c7f6.
board/ti/tnetv107xevm/Makefile added in HEAD
But files were identical, so no problem.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds support for the Marvell Orion5x SoC.
It has no use alone, and must be followed by a patch
to add Orion5x support for serial, then support for
the ED Mini V2, an Orion5x-based product from LaCie.
Signed-off-by: Albert Aribaud <albert.aribaud@free.fr>
Do not enforce drivers to provide empty video_set_lut()
if they do not implement indexed color (8 bpp) frame
buffer support. Add default function to the cfb_console
driver and remove empty video_set_lut() functions.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Part of this patch is by: Mikhail Kshevetskiy.
Stack must be aligned to 8 bytes on PXA (possibly all armv5te) for LDRD/STRD
instructions. In case LDRD/STRD is issued on an unaligned address, the behaviour
is undefined.
The issue was observed when working with the NAND code, which was rendered
disfunctional. Also, the vsprintf() function had serious problems with printing
64bit wide long longs. After aligning the stack, this wrong behaviour is no
longer present.
Tested on:
Marvell Littleton PXA310 board
Toradex Colibri PXA320 board
Aeronix Zipit Z2 PXA270 handheld
Voipac PXA270 board
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Provides initial support for TI OMAP-L138/DA850 SoC devices on
a Logic PD EVM board.
Provides:
Initial boot and configuration.
Support for i2c.
UART support (console).
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Acked-by: Ben Gardiner <bengardiner@nanometrics.ca>
Reviewed-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
initialized for CS1
From: Vaibhav Hiremath <hvaibhav@ti.com>
The patch makes sure that size for SDRC CS1 gets calculated
only when the CS1 SDRC is initialized.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This is an initial commit with
basic functionality, more commits with drivers, etc. to follow.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch adds support for the EMIF4 interface
available in the AM35x processors.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Consolidated SDRC related functions into one file - sdrc.c
And also replaced sdrc_init with generic memory init
function (mem_init), this generalization of omap memory setup
is necessary to support the new emif4 interface introduced in AM3517.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
initialized for CS1
From: Vaibhav Hiremath <hvaibhav@ti.com>
The patch makes sure that size for SDRC CS1 gets calculated
only when the CS1 SDRC is initialized.
Signed-off-by: Vaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
TNETV107X is a Texas Instruments SoC based on an ARM1176 core, and with a
bunch on on-chip integrated peripherals. This is an initial commit with
basic functionality, more commits with drivers, etc. to follow.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The current ARM1176 CPU specific code is too specific to the SMDK6400
architecture. The following changes were necessary prerequisites for the
addition of other SoCs based on ARM1176.
Existing board's (SMDK6400) configuration has been modified to keep behavior
unchanged despite these changes.
1. Peripheral port remap configurability
The earlier code had hardcoded remap values specific to s3c64xx in start.S.
This change makes the peripheral port remap addresses and sizes configurable.
2. U-Boot code relocation support
Most architectures allow u-boot code to run initially at a different
address (possibly in NOR) and then get relocated to its final resting place
in RAM. Added support for this capability in ARM1176 architecture.
3. Disable TCM if necessary
If a ROM based bootloader happened to have initialized TCM, we disable it here
to keep things sane.
4. Remove unnecessary SoC specific includes
ARM1176 code does not really need this SoC specific include. The presence
of this include prevents builds on other ARM1176 archs.
5. Modified virt-to-phys conversion during MMU disable
The original MMU disable code masks out too many bits from the load address
when it tries to figure out the physical address of the jump target label.
Consequently, it ends up branching to the wrong address after disabling the
MMU.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The ARM1136 cache_flush() function uses the "mcr p15, 0, rn, c7, c7, 0"
instruction which means "Invalidate Both Caches" when in fact the intent
is to clean and invalidate all caches. So add an "mcr p15, 0, %0, c7,
c10, 0" instruction to "Clean Entire Data Cache" prior to the "Invalidate
Both Caches" instruction to insure that memory is consistent with any
dirty cache lines.
Also fix a couple of "flush v*" comments in ARM1136 cpu_init_crit() so
that they correctly describe the actual ARM1136 CP15 C7 Cache Operations
used.
Signed-off-by: George G. Davis <gdavis@mvista.com>
Add the 'clkdvdr' and 'pmuxcr2' registers to the 85xx definition of
struct ccsr_gur.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch allows users to override default STANDALONE_LOAD_ADDR.
The gcclibdir path was duplicated in the standalone Makefile and
can be removed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch fixes the run-time error on div64 when built with
gcc4, which was reported by jhwu0625 on nios forum. It merges
math support from libgcc of gcc4. This patch is copied from
nios2-linux.
It works with both gcc3 and gcc4. The old mult.c, divmod.c and
math.h are removed.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
The "-ffixed-r15" option doesn't work well for gcc4. Since we
don't use gp for small data with option "-G0", we can use gp
as global data pointer. This allows compiler to use r15. It
is necessary for gcc4 to work properly.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch adds driver for a trivial gpio core, which is described
in http://nioswiki.com/GPIO. It is used for gpio led and nand flash
interface in u-boot.
When CONFIG_SYS_GPIO_BASE is not defined, board may provide
its own driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Tested-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Scott McNutt <smcnutt@psyent.com>
This patch adds support for full MII interface on MCF5445x (in contrast
to RMII as used on the evaluation boards).
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
This patch adds the possibility to handle seperate PHYs to MCF5445x.
Naming is chosen to resemble the contrary CONFIG_FEC_SHARED_PHY in the
linux kernel.
Signed-off-by: Wolfgang Wegner <w.wegner at astro-kom.de>
For CONFIG_SYS_BOOTCOUNT_SINGLEWORD the code had an endianness problem.
Signed-off-by: Michael Weiss <michael.weiss@ifm.com>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Fix the following compiler problems:
arch/arm/cpu/arm920t/a320/liba320.a(timer.o): In function `udelay':
/home/wd/git/u-boot/work/arch/arm/cpu/arm920t/a320/timer.c:160: multiple definition of `udelay'
lib/libgeneric.a(time.o):/home/wd/git/u-boot/work/lib/time.c:34: first defined here
lib/libgeneric.a(time.o): In function `udelay':
time.c:(.text+0x1c): undefined reference to `__udelay'
Signed-off-by: Wolfgang Denk <wd@denx.de>
commit c7190f028f "mpc83xx:
retain POR values of non-configured ACR, SPCR, SCCR, and LCRR
bitfields" incorrectly shifted <register>_<bitfield> (e.g.
ACR_PIPE_DEP) values that were preshifted by their
definition in mpc83xx.h.
this patch removes the unnecessary shifting for the newly
utilized mask values in cpu_init.c, and prevents seemingly
unrelated symptoms such as an mpc8379erdb board from
locking up whilst performing a networking operation,
e.g. a tftp.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>