SCFG_SCFGREVCR is SCFG bit reverse register. This register
must be written with 0xFFFFFFFF before writing to any other
SCFG register. Then other SCFG register could be written in
big-endian mode.
Address: 157_0000h base + 200h offset = 157_0200h
Bit 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15|16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31
W/R SCFGREV
Reset 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0-31
SCFGREV SCFG Bit Reverse Control Filed
32'h 0000_0000 - No bit reverse is applied
32'h FFFF_FFFF - Bit reverse is applied; so 31:0 will be stored/read as
0:31
This patch removes the bit reversing for SCFG registers in
u-boot. It will be implemented through PBI commands in RCW
.pbi
write 0x570200, 0xffffffff
.end
So other SCFG register could be written in big-endian mode
in u-boot or kernel directly.
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Disable the snoop for slave interface 0, 1 and 2
to avoid the interleaving on the CCI400 BUS.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* Run "mtdparts default" to create NAND partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
* fdt_fixup_mtdparts is called from ft_board_setup
* run "mtdparts default" to create NAND, NOR partition on uboot
* Use mtdparts to create partitions dynamically rather
than using static partitions in device tree
Signed-off-by: Ashish Kumar <Ashish.Kumar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
-A_007662 states that for x1 link width, PCIe2 controller trains in
Gen1 speed while configured for Gen2 speed.
Workaround:Set the width to x1 and speed to Gen2 by writing to
CCSR registers in PBI phase
-A_008007 states that PVR register may show random value.
Workaround: Reset PVR register using DCSR space in PBI phase
Add PBI based software workaround for A_007662 and A_008007
in t104x_pbi.cfg. This is required for SPL-based bootloaders
like NAND-boot, SD-boot, SPI-boot
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This support of CPLD includes
- Files and register definitions
- Command to switch alternate bank
- Command to switch default bank
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
When an invalid USDHC port is passed we should return -EINVAL instead of 0.
Also, return the error immediately on fsl_esdhc_initialize() failure.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
This patch will enable the support for SPL on iMX6 SabreSD.
It tested on SD2 and SD3 mmc port (Switch 1 or 2 of SW6)
Signed-off-by: John Tobias <john.tobias.ph@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
The i.MX6Q/DL sabreauto board has one NAND socket, set the
CONFIG_NAND_MXS and relevant NAND configurations to enable the
MXS NAND flash driver.
Add board level codes to set IOMUX and clock for GPMI-NAND and
BCH module.
Signed-off-by: Ye.Li <B37916@freescale.com>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Since kernel 3.15 there are two dtb's for the imx53-qsb board:
imx53-qsb.dtb - For the boards with DA9053 PMIC
imx53-qsrb.dtb - For the boards with MC34708 PMIC
Change the 'fdt_file' dynamically, so that the correct dtb can be used depending
on the board variant.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Otavio Salvador <otavio@ossystems.com.br>
On mx6 sabreauto board, there are two USB ports:
0: OTG
1: HOST
The EHCI driver is enabled for this board, but the IOMUX and VBUS power
control is not implemented, which cause both USB port failed to work.
This patch fix the problem by adding the board support codes.
Since the power control uses the GPIO pin from port expander MAX7310,
the PCA953X driver is enabled for accessing the MAX7310.
The ID pin of OTG Port needs to configure the GPR1 bit 13 for selecting
its daisy chain. Add a new function "imx_iomux_set_gpr_register" to
handle GPR register setting.
Signed-off-by: Ye.Li <B37916@freescale.com>
There are three SD/MMC sockets on mx6slevk boards. Implements the
full support for them.
The default boot socket is USDHC2, so the MMC environment is set
to that device.
Signed-off-by: Ye.Li <B37916@freescale.com>
Add support for the 4.3'' Seiko WVGA parallel display.
In order to direct the splash screen to the Seiko display:
=> setenv panel SEIKO-WVGA
=> save
=> reset
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This commit introduces a Kconfig symbol for each ARM CPU:
CPU_ARM720T, CPU_ARM920T, CPU_ARM926EJS, CPU_ARM946ES, CPU_ARM1136,
CPU_ARM1176, CPU_V7, CPU_PXA, CPU_SA1100.
Also, it adds the CPU feature Kconfig symbol HAS_VBAR which is selected
for CPU_ARM1176 and CPU_V7.
For each target, the corresponding CPU is selected and the definition of
SYS_CPU in the corresponding Kconfig file is removed.
Also, it removes redundant "string" type in some Kconfig files.
Signed-off-by: Georges Savoundararadj <savoundg@gmail.com>
Acked-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
The config targets described in README are not present
any more, update the info to currently used targets.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Provide a public declaration of the board_spi_cs_gpio()
callback for i.MX SPI chip selects to prevent the warning
"Should it be static?" when compiling with "make C=1".
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Hardware accelerated support for SHA-1 and SHA-256 has been added.
Hash command enabled along with hardware accelerated support for
SHA-1 and SHA-256 for platforms which have CAAM block.
Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Removed settings in unsupported register fields. They didn’t
do anything, and in most cases, were not documented in the
reference manual.
Changed register settings to comply with JEDEC required values.
Changed timing parameters because they included full clock
periods that were doing nothing.
Signed-off-by: Anthony Felice <tony.felice@timesys.com>
[rebased on v2014.10-rc2]
Signed-off-by: Stefan Agner <stefan@agner.ch>
Update the ddr scripts for LPDDR2 and add two build configs for LPDDR2
arm2 board. Since the LPDDR2 arm2 board has different DDR size, use
CONFIG_DDR_MB in defconfig to replace the PHYS_SDRAM_SIZE.
Signed-off-by: Ye.Li <B37916@freescale.com>
This patch adds the i.MX6DL arm2 board support. The i.MX6DL ARM2
shared the same board with i.MX6Q ARM2 board since the i.MX6DL is
pin-pin compatible with i.MX6Q.
The patch also support the DDR 32-BIT mode option. Please define
CONFIG_DDR_32BIT in the board configure file to enable DDR 32-BIT
mode.But due to the board design, it's 64bit DDR buswidth physically,
so, if you CONFIG_DDR_32BIT, the DDR memory size will be half of it.
Signed-off-by: Ye.Li <B37916@freescale.com>
LS1021AQDS has a variant with DDR4 slot. This patch adds a new defconfig
for this variant to enable DDR4 support. RAW timing parameters are not
added for DDR4. The board timing parameters are only tuned for single-
rank 1600 and 1800MT/s with Micron DIMM 9ASF51272AZ-2G1A1 due to DIMM
availability.
Signed-off-by: York Sun <yorksun@freescale.com>
CC: Alison Wang <alison.wang@freescale.com>
Spin table is at the very beginning of boot code. Each core has an individual
release address within the spin table, the ft_cpu_setup fn updates the
"cpu-release-addr" property of each cpu node with the corresponding release
address.
Also fix CPU_RELEASE_ADDR to point to secondary_boot_func.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Arnab Basu <arnab.basu@freescale.com>
DP-DDR is used for DPAA, separated from main memory pool for general
use. It has 32-bit bus width and use a standard DDR4 DIMM (64-bit).
Signed-off-by: York Sun <yorksun@freescale.com>
Since commit ddaf5c8f30
(patman: RunPipe() should not pipe stdout/stderr unless asked),
Patman spits lots of "Invalid MAINTAINERS address: '-'"
error messages for patches with global changes.
It takes too long for Patman to process them.
Anyway, "M: -" does not carry any important information.
Rather, it is just like a place holder in case of assigning
a new board maintainer. Let's comment out.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '/^M:[[:blank:]]*-$/s/^/#/'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The "S: Orphan" in MAINTAINERS means that the maintainer in the
"M:" field is unreachable (i.e. the email address is not working).
(Refer to the definition of "Orphan" adopted in U-Boot
in the log of commit 31f1b654b2,
"boards.cfg: move boards with invalid emails to Orphan")
For patch files adding global changes, scripts/get_maintainer.pl
adds bunch of such invalid email addresses, which results in
tons of annoying bounce emails.
This commit can be reproduced by the following command:
find . -name MAINTAINERS | xargs sed -i -e '
/^M:[[:blank:]]/ {
N
/S:[[:blank:]]Orphan/s/^/#/
}
'
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
T1042QDS (T1042 is T1040 Personality without L2 switch) supports following
sgmii interfaces with serdes protocol 0xA7
-SGMII-MAC3 on Lane B - slot 7
-SGMII-MAC5 on Lane H - slot 7
-SGMII2.5G-MAC1 on Lane C - slot 6
-SGMII2.5G-MAC2 on Lane D - slot 5
Add support of above sgmii interfaces
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
DDR-ODT require cfg_dram_type switch set properly as per DDR type.
T1040RDB, T1042RDB boards have DDR3L type DDR, so cfg_dram_type
should be set to OFF for DDR3L
Update t104xrdb/README for switch setting
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
T1042RDB is a Freescale reference board that hosts the T1042 SoC
(and variants). The board is similar to T1040RDB, T1042 is a reduced
personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch).
T1042RDB is configured with serdes protocol 0x86 which can support
following interfaces
- 2 RGMII's on DTSEC4, DTSEC5
- 1 SGMII on DTSEC3
DTSEC1, DTSEC2 are not connected on board.
This Patch
- add T1042RDB support
- updates README file for T1042RDB details and update commands for switching
to alternate banks from vBank0 to vBank4 and vice versa
This patch also does minor clean ups for fdt defines for T1042RDB and
T1042RDB_PI board
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds support of rcw for T1042RDB, it makes following changes :
- Adds t1042_rcw.cfg file for serdes protocol 0x86 for T1042RDB
- Renames t1042_pi_rcw.cfg file from t1042_rcw.cfg and also updates
comments for valid serdes protocol which is 0x06
- Also updates CONFIG_SYS_FSL_PBL_RCW for T1042RDB
Signed-off-by: Vijay Rai <vijay.rai@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
LS2085a has 2 regions in system memory map. Region1 is default map from
where system boots. Once u-boot is moved to DDR, IFC is re-mapped to
Region2.
So, update gd->env_addr to reflect correct address.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
MXC SPI driver has a feature whereas a GPIO line can be used to force CS high
across multiple transactions. This is set up by embedding the GPIO information
in the CS value:
cs = (cs | gpio << 8)
This merge of cs and gpio data into one value breaks the sf probe command:
if the use of gpio is required, invoking "sf probe <cs>" will not work, because
the CS argument doesn't have the GPIO information in it. Instead, the user must
use "sf probe <cs | gpio << 8>". For example, if bank 2 gpio 30 is used to force
cs high on cs 0, bus 0, then instead of typing "sf probe 0" the user now must
type "sf probe 15872".
This is inconsistent with the description of the sf probe command, and forces
the user to be aware of implementaiton details.
Fix this by introducing a new board function: board_spi_cs_gpio(), which will
accept a naked CS value, and provide the driver with the relevant GPIO, if one
is necessary.
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Eric Benard <eric@eukrea.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Provide cgtqmx6eval board its own variant of ddr
setup config file. Move board/freescale/imx/ddr/
mx6q_4x_mt41j128.cfg to board/freescale/mx6sabresd/
as this is was designed for the mx6sabresd board.
Signed-off-by: Nitin Garg <nitin.garg@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
commit d6d07a9b... arm: vf610: add NAND support for vf610twr
generates the following warnings:
WARNING: no status info for 'vf610twr_nand'
WARNING: no maintainers for 'vf610twr_nand'WARNING: no status info for
'vf610twr_nand'
This is due to the fact that vf610twr_nand_defconfig has no Maintainer.
This patch proposed Alison as Maintainer and fix it.
Signed-off-by: Stefano Babic <sbabic@denx.de>
Acked-by: Alison Wang <b18965@freescale.com>
CC: Stefan Agner <stefan@agner.ch>