The DM365 config was using the 'CONFIG_CMD_SAVEENV' flag.
This is already included when we include the
config_cmd_default.h header file. So this flag is removed.
Also another flag to enable NAND functions was being
enabled incorrectly.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch does the following
1) Enables the NAND driver which is now available.
2) Enables the 'CONFIG_MTD_DEVICE' as without this the
compilation will fail
3) We now have a safe place to store environment and defines
an offset where this can be stored. This offset value is such that it is after
the location where U-Boot is flashed using TI flash utilities.
4) Enables Bootdelay
5) Increases malloc() arena size. Manufacturers are coming out with
NAND with large blocks sizes of upto 1 MiB. It has been noticed that
as the block size of the NAND used is increased, if this particular
value is not increased, the NAND driver will output out of memory
errors.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
The Default mode that is built for the Davinci DVEVM happens
to be the NOR mode.
When we want to build for the NAND mode, we get a compilation
error. This is overcome by defining the CONFIG_MTD_DEVICE
flag in the NAND mode.
The image built for NAND mode was successfully tested on the
DaVinci DM6446 EVM.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
This patch removes the asm/sizes.h header file from being
included in the DaVinci SOC configs.
References to SZ_xx have been replaced by appropriate
bit shifted values.
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Acked-by: Wolfgang Denk <wd@denx.de>
commit 6d0f6bcf33 did the big
rename of CFG_ macros to CONFIG_SYS macros. But it missed
a couple of instances within comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This fixes the code and the comment according to the original intent of
doing an intensive memory test when PSC6_3 is pulled low on the STK52xx.
Notably PORT_CONFIG will be overridden with this correct code now,
so beware.
The original code only worked by coincidence depending on the PORT_CONFIG
setting from the header file. The new code was tested to ensure that the
(undocumented) memory test still works on the STK52x.
Signed-off-by: Detlev Zundel <dzu@denx.de>
CC: Martin Krause <Martin.Krause@tqs.de>
Minor white-space cleanup.
Signed-off-by: Wolfgang Denk <wd@denx.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI
added
Also:
- changed CONFIG_DRIVER_SMC91111 to CONFIG_SMC91111
- cleaned up line lengths
- modified all boards that override weak function in this driver
- modified all eeprom standalone apps to work with new driver
- updated blackfin standalone EEPROM app after testing
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The following changes allow U-Boot to fully relocate from flash to
RAM:
- Remove linker scripts' .fixup sections from the .text section
- Add -mrelocatable to PLATFORM_RELFLAGS for all boards
- Define CONFIG_RELOC_FIXUP_WORKS for all boards
Previously, U-Boot would partially relocate, but statically initialized
pointers needed to be manually relocated.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
This patch adds support to detect the amount of DDR2 SDRAM
on PMC440 modules. Detection is done by probing through
a list of available and supported hardware configurations
from 1GByte down to 256MB.
The static TLB entry is replaced by dynamically created entries.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The Linux kernel has changed the way it numbers serial ports, so update
the default command line to match it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The u-boot image has outgrown the current space and overflowed into the
env sector. So move the env to the next available sector (we've already
allocated the first few sectors anyways for u-boot).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The MPC8536E is capable of booting from the on-chip ROM - boot from
eSDHC and boot from eSPI. When power on, the porcessor excutes the
ROM code to initialize the eSPI/eSDHC controller, and loads the mian
U-Boot image from the memory device that interfaced to the controller,
such as the SDCard or SPI EEPROM, to the target memory, e.g. SDRAM or
L2SRAM, then boot from it.
The memory device should contain a specific data structure with control
word and config word at the fixed address. The config word direct the
process how to config the memory device, and the control word direct
the processor where to find the image on the memory device, or where
copy the main image to. The user can use any method to store the data
structure to the memory device, only if store it on the assigned address.
The on-chip ROM code will map the whole 4GB address space by setting
entry0 in the TLB1, so the main image need to switch to Address space 1
to disable this mapping and map the address space again.
This patch implements loading the mian U-Boot image into L2SRAM, so
the image can configure the system memory by using SPD EEPROM.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
MPC8536E can support booting from NAND flash which uses the
image u-boot-nand.bin. This image contains two parts: a 4K
NAND loader and a main U-Boot image. The former is appended
to the latter to produce u-boot-nand.bin. The 4K NAND loader
includes the corresponding nand_spl directory, along with the
code twisted by CONFIG_NAND_SPL. The main U-Boot image just
like a general U-Boot image except the parts that included by
CONFIG_SYS_RAMBOOT.
When power on, eLBC will automatically load from bank 0 the
4K NAND loader into the FCM buffer RAM where CPU can execute
the boot code directly. In the first stage, the NAND loader
copies itself to RAM or L2SRAM to free up the FCM buffer RAM,
then loads the main image from NAND flash to RAM or L2SRAM
and boot from it.
This patch implements the NAND loader to load the main image
into L2SRAM, so the main image can configure the RAM by using
SPD EEPROM. In the first stage, the NAND loader copies itself
to the second to last 4K address space, and uses the last 4K
address space as the initial RAM for stack.
Obviously, the size of L2SRAM shouldn't be less than the size
of the image used. If so, the workaround is to generate another
image that includes the code to configure the RAM by SPD and
load it to L2SRAM first, then relocate the main image to RAM
to boot up.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
By nature of being based off the MPC8548CDS board, this
board inherited an ENV_SIZE setting of 256k. But since
it has a smaller flash device (8MB soldered on), it has
a native sector size of 128k, and hence the ENV_SIZE was
causing 2 sectors to be used for the environment.
By removing the unused sector, we can push TEXT_BASE up
closer to the end of address space and reclaim that
sector for any other application. This also fixes the
mismatch between TEXT_BASE and MONITOR_LEN reported by
Kumar earlier.
Since this board also supports the ability to boot off
the 64MB SODIMM flash, this change is forward looking
with that in mind; i.e. the settings for MONITOR_LEN
and ENV_SIZE will work when the 512k sectors of the
SODIMM flash are used for alternate boot in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the board config header. This takes advantage of
that for the sbc8349 board.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
With this patch we can change QE USB mode without need to hand-edit
the device tree.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch fixes various ethernet issues with gigabit links handling
in U-Boot. The workarounds originally implemented by Kim Phillips for
Linux kernel.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
U-Boot can detect if an IDE device is present or not.
If not, and this new config option is activated, U-Boot
removes the ATA node from the DTS before booting Linux,
so the Linux IDE driver does not probe the device and
crash. This is needed for buggy hardware (uc101) where
no pull down resistor is connected to the signal IDE5V_DD7.
Signed-off-by: Heiko Schocher <hs@denx.de>
- As these boards are similiar, collect common config options
in manroland/common.h and manroland/mpc52xx-common.h
for mpc5200 specific common options for this manufacturer.
- add OF support
- update default environment
Signed-off-by: Heiko Schocher <hs@denx.de>
Minor edit of commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Martha M Stan <mmarx@silicontkx.com>
Minor cleanup:
Re-ordered default_mddrc_config[] to have matching indices.
This allows to use the same index "N" for source and target fields;
before, we had code like this
out_be32(&im->mddrc.ddr_time_config2, mddrc_config[3]);
which always looked like a copy & paste error because 2 != 3.
Also, use NULL when meaning a null pointer.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Commit 804d83a5 allows us to move all the configuration
variation tweaks out of the top level Makefile and down
into the boards config header. This takes advantage of
that for the sbc8540/sbc8560 boards.
There were a couple of cheezy comments pointing at incorrect
files, or files that don't exist, so I've cleaned those up too.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, and if you had 33MHz PCI, you
had to manually change CONFIG_SYS_NS16550_CLK too, which was
not real user friendly,
This adds the typical PCI and clock speed make targets to the
toplevel Makefile in accordance with what is being done with
other boards (i.e. using the "-t" to mkconfig).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI/PCI-e support for the sbc8548 was based on an earlier
version of what the MPC8548CDS board was using, and in its
current state it won't even compile. This re-syncs it to match
the latest codebase and makes use of the new shared PCI functions
to reduce board duplication.
It borrows from the MPC8568MDS, in that it pulls the PCI-e I/O
back to 0xe280_0000 (where PCI2 would be on MPC8548CDS), and
similarly it coalesces the PCI and PCI-e mem into one single TLB.
Both PCI-x and PCI-e have been tested with intel e1000 cards
under linux (with an accompanying dts change in place)
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The size of the LB SDRAM on this board is 128MB, spanning CS3
and CS4. It was previously only being configured for 64MB on
CS3, since that was what the original codebase of the MPC8548CDS
had. In addition to setting up BR4/OR4, this also adds the TLB
entry for the second half of the SDRAM.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The sbc8548 has a 64MB SODIMM flash module off of CS6 that
previously wasn't enumerated by u-boot. There were already
BR6/OR6 settings for it [used by cpu_init_f()] but there
was no TLB entry and it wasn't in the list of flash banks
reported to u-boot.
The location of the 64MB flash is "pulled back" 8MB from
a 64MB boundary, in order to allow address space for the
8MB boot flash that is at the end of 32 bit address space.
This means creating two 4MB TLB entries for the 8MB chunk,
and then expanding the original boot flash entry to 64MB
in order to cover the 8MB boot flash and the remainder
(56MB) of the user flash.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
There are a couple defines and PCI bridge quirks related to the PCI
backplane of the MPC8548CDS that have no meaning in the context of
the port to the sbc8548 board, so delete them.
Also, the form factor of the sbc8548 is a standalone board with a
single PCI-X and a single PCI-e slot. That pretty much guarantees
that it will never be a PCI agent itself, so the host/agent and root
complex/end node distinctions have been removed.
Similarly, since there is no physical connector mapping to PCI2, so
all references of PCI2 in the board support files have been removed
as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For some reason the CLKDIV field varies between SoC in how it interprets
the bit values.
All 83xx and early (e500v1) PQ3 devices support:
clk/2: CLKDIV = 2
clk/4: CLKDIV = 4
clk/8: CLKDIV = 8
Newer PQ3 (e500v2) and MPC86xx support:
clk/4: CLKDIV = 2
clk/8: CLKDIV = 4
clk/16: CLKDIV = 8
Ensure that the MPC86xx and MPC85xx still get the same behavior and make
the defines reflect their logical view (not the value of the field).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Peter Tyser <ptyser@xes-inc.com>
Add version environment variable configuration to the galaxy5200
board header file.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
DDR2 timing for intip was on the edge for some of the available chips
for this board. Now it is verfied to work with all of them.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The more standard 'source' command provides identical functionality to
the autoscr command.
Environment variable names/values on the MVBC_P, MVBML7, kmeter1,
mgcoge, and km8xx boards are updated to no longer refernce 'autoscr'.
The 'autoscript' and 'autoscript_uname' environment variables are
also removed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Heiko Schocher <hs@denx.de>
Acadia still used the "old" arch/ppc bootm commands for booting
Linux images without FDT. This patch now enables these fdt-aware
boot commands for Acadia as well.
Signed-off-by: Stefan Roese <sr@denx.de>
So that we can set the NAND loader's relocate stack pointer
to the value other than the relocate address + 0x10000.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove Ethernet node fixup from mgcoge and muas3001 boards and modify its
configs for the common mpc8260 code to use generic Ethernet fixup.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@noser.com>
Tested-by: Heiko Schocher <hs@denx.de>
This patch cleans up multiple issues of the 4xx register (mostly
DCR, SDR, CPR, etc) definitions:
- Change lower case defines to upper case (plb4_acr -> PLB4_ACR)
- Change the defines to better match the names from the
user's manuals (e.g. cprpllc -> CPR0_PLLC)
- Removal of some unused defines
Please test this patch intensive on your PPC4xx platform. Even though
I tried not to break anything and tested successfully on multiple
4xx AMCC platforms, testing on custom platforms is recommended.
Signed-off-by: Stefan Roese <sr@denx.de>
Using a separate "u-boot" environment variable allows to easily
specify different filenames for the update procedure. This is also in
line with many other board configurations defining an "update" script.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Reset any i2c devices that may have been interrupted during a system reset.
Normally this would be accomplished by clocking the line until SCL and SDA
are released and then sending a start condtiion (From an Atmel datasheet).
There is no direct access to the i2c pins so instead create start commands
through the i2c interface. Send a start command then delay for the SDA Hold
time, repeat this by disabling/enabling the bus a total of 9 times.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Now that the PCI, SATA et al compile problems have been resolved, the
cludge that was applied to avoid them can be removed
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Primary intent is to resolve build errors for this board which has been
neglected for a very long time. I do not have one of these boards, so I
cannot test functionality
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Change PCI_REGION_MEMORY to PCI_REGION_SYS_MEMORY (Originally done in
commit ff4e66e93c, regressed by commit 6d7f610b09)
Cast PCI_ROM_ADDRESS_MASK to u32
Wrap probe_pci_video() call inside #ifdef CONFIG_VIDEO
Change call to pci_find_class() to pci_find_devices(). This is based on a
patch submitted on 1st March 2007 (Patch that fixes the compilation errors
for sc520_cdp board) by mushtaq_k
This patch requires that PCI_VIDEO_VENDOR_ID and PCI_VIDEO_DEVICE_ID be
specified in the board config file. Dummy values have been added for the
SC520 CDP board to enable compilation, but since I do not have one of these,
I do know what the values should be
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
The current configuration of the Environment has the redundant copy of the
environment in the Boot Flash - This was never the intent. The Environment
should instead be in the first two sectors of the first Strata Flash
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
Since the NAND code now uses 64bit code, make sure we enable support for
ADI Blackfin boards in printf to avoid the warning:
nand_util.c:45:2: warning: #warning Please define CONFIG_SYS_64BIT_VSPRINTF for correct output!
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The CM-BF537U is similar to the CM-BF537E module, but enough to need its
own board port.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add dns and ntp to default networking commands, and ask for more dhcp
options to better configure the network environment.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Calao TNY-A9260 and TNY-9G20 are boards manufactured and sold by
Calao Systems <http://www.calao-systems.com>. Their components are very
similar to the AT91SAM9260EK board, so their configuration is based on
the configuration of this board. There are however some differences:
different clocks, no LCD, no ethernet. They also can use SPI EEPROM to
store the environment.
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The Calao SBC35-A9G20 board is manufactured and sold by Calao Systems
<http://www.calao-systems.com>. It is built around an AT91SAM9G20 ARM SoC
running at 400MHz. It features an Ethernet port, an SPI RTC backed by an onboard
battery , an SD/MMC slot, a CompactFlash slot, 64Mo of SDRAM, 256Mo of NAND
flash, two USB host ports, and an USB device port. More informations can be
found at <http://www.calao-systems.com/articles.php?lng=en&pg=5936>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch adds support for i.MX27-LITEKIT development board from
LogicPD. This board uses i.MX27 SoC and has 2MB NOR flash, 64MB NAND
flash, FEC ethernet controller integrated into i.MX27.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
Acked-by: Wolfgang Denk <wd@denx.de>
Call fsl_pci_init_port() to initialize all the PCIe ports on the board.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With current values of CONFIG_SYS_MEMTEST_START and CONFIG_SYS_MEMTEST_END
memory test hangs if run without arguments. Set them to sane values, so
that all available 512MB of RAM excluding exception vectors at the bottom
and u-boot code and stack at the top can be tested.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code base adds P1 & P2 RDB platforms support.
The folder and file names can cater to future SOCs of P1/P2 family.
P1 & P2 processors are 85xx platforms, part of Freescale QorIQ series.
Tested following on P2020RDB:
1. eTSECs
2. DDR, NAND, NOR, I2C.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The number of CPUs are getting detected dynamically by checking the
processor SVR value. Also removed CONFIG_NUM_CPUS references from all
the platforms with 85xx/86xx processors.
This can help to use the same u-boot image across the platforms.
Also revamped and corrected few Freescale Copyright messages.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We move all IO addressed (CCSR, localbus, PCI) above the 4G boundary
to allow for larger memory sizes.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The old PCI ATMU setup code would just mimic the PCI regions into the
ATMU registers. For simple memory maps in which all memory, MMIO, etc
space fit into 4G this works ok. However there are issues with we have
>4G of memory as we know can't access all of memory and we need to
ensure that PCICSRBAR (PEXCSRBAR on PCIe) isn't overlapping with
anything since we can't turn it off.
We first setup outbound windows based on what the board code setup
in the pci regions for MMIO and IO access. Next we place PCICSRBAR
below the MMIO window. After which we try to setup the inbound windows
to map as much of memory as possible.
On PCIe based controllers we are able to overmap the ATMU setup since
RX & TX links are separate but report the proper amount of inbound
address space to the region tracking to ensure there is no overlap.
On PCI based controllers we use as many inbound windows as available to
map as much of the memory as possible.
Additionally we changed all the CCSR register access to use proper IO
accessor functions. Also had to add CONFIG_SYS_CCSRBAR_PHYS to some
86xx platforms that didn't have it defined.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
apparently the ITX was missed last round.
Also make bootdelay consistent with other boards, so as to give on the
opportunity to fix mistakenly set bootcmd without having checked for an
bootdelay zero setting first.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_CS8900 to CONFIG_CS8900
- changed CS8900_BASE to CONFIG_CS8900_BASE
- changed CS8900_BUS?? to CONFIG_CS8900_BUS??
- cleaned up line lengths
- modified VCMA9 command function that accesses the device
- removed MAC address initialization from lib_arm/board.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Wolfgang Denk <wd@denx.de>
Acked-by: Wolfgang Denk <wd@denx.de>
This chooses 4kB data size for both TFTP and NFS, as an example
about how to use support for IP fragments.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Add support for the DEKA Research and Development galaxy5200 board
The galaxy5200 is an Freescale mpc5200 based embedded industrial
control board.
Signed-off-by: Eric Millbrandt <emillbrandt@dekaresearch.com>
Some boards have fallen out of sync by defining CONFIG_ENV_IS_EMBEDDED
manually. While it is useful to have this available to the build system,
let's do it automatically rather than forcing people to opt into it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Newer revisions of these boards have slightly larger flashes, so increase
the configured number of sectors so that U-Boot works on all revisions.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot
at either:
NET: Registered protocol family 16
or the
io scheduler cfq registered
message. Fixing up these DDR settings appears to fix the problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
commit 9993e196da "mpc83xx: convert all
remaining boards over to 83XX_GENERIC_PCI" remapped pci windows on
tqm834x to make it more consistent with the other 83xx boards. During
that time however, the author failed to realize that FLASH_BASE was
occupying the same range as what PCI1_MEM_BASE was being assigned.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Wolfgang Denk <wd@denx.de>
This was introduced with the MPC8349EMDS board, and then copied to
a couple other boards by nature of being the reference implementation.
u-boot$git grep CONFIG_SYS_MID_FLASH_JUMP
include/configs/MPC8349EMDS.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/sbc8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
include/configs/vme8349.h:#define CONFIG_SYS_MID_FLASH_JUMP 0x7F000000
u-boot$
It currently isn't used, so delete it before it spreads further.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Prior to this commit, to enable PCI, you had to go manually
edit the board config header, which isn't really user friendly.
This adds the typical PCI make targets to the toplevel Makefile
in accordance with what is being done with other boards.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
The name of the atmel nand driver in the kernel changed from at91_nand
to atmel_nand back in June 2008, but the at91-based boards config files
still refer to at91_nand. This patch updates them with the new name
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
This patch fixes the "chip_config" command for I2C bootstrap EEPROM
configuration. First it changes the I2C bootstrap EEPROM address to
0x54 as this is used on Arches (instead of 0x52 on Canyonlands/
Glacier). Additionally, the NAND bootstrap settings are removed
for Arches since Arches doesn't support NAND-booting.
Signed-off-by: Stefan Roese <sr@denx.de>
For some reason the MPC8544 enabled BEDBUG if PCI was enabled and that
got copied int the MPC8536, MPC8572 and P2020 DS boards. The BEDBUG
support has never been made to work completely on e500/85xx so we
just disable it to save space and match the other FSL 85xx boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
It is recommended to define the macro CONFIG_SYS_64BIT_VSPRINTF
for NAND specific warning removal, same is done in this patch
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Embedd chip select configuration into struct for gpmc config
instead of having it completely separated as suggested by
Wolfgang Denk on
http://lists.denx.de/pipermail/u-boot/2009-May/052247.html
Signed-off-by: Matthias Ludwig <mludwig@ultratronik.de>
For some reason the AT91rm9200 lowlevel init writes to a bunch of
reserved or read-only addresses. All the boards seem to define the
value-to-be-written values as zero ... but they shouldn't actually
be writing *anything* there.
No documented erratum justifies these accesses. It looks like maybe
some pre-release BDI-2000 setup code has been carried along by cargo
cult programming since at least late 2004 (per GIT history).
Here's a patch disabling what seems to be bogosity. Tested on a
csb337; there were no behavioral changes.
Signed-off-by: David Brownell <david-b@pacbell.net>
on RM9200ek
Tested-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch moves the load addresses for kernel, fdt and ramdisk to higher
addresses (>= 16MB). This enables booting of bigger kernel images (e.g.
lockdep enabled).
Signed-off-by: Stefan Roese <sr@denx.de>
This patch changes CONFIG_SYS_BOOTMAPSZ from 8MB to 16MB which is the
initial TLB on 40x PPC's in the Linux kernel. With this change even bigger
Linux kernels (> 8MB) can be booted.
This patch also sets CONFIG_SYS_BOOTM_LEN to 16MB (default 8MB) to enable
decompression of bigger images.
Signed-off-by: Stefan Roese <sr@denx.de>
Because twl4030 now has its own device files, move and rename
twl4030_mmc_config.
twl4030_mmc_config initializes the twl4030 power setting to
the mmc device. Because it is in the twl4030 power domain, move
it out of drivers/mmc/omap3_mmc.c and into drivers/power/twl4030.c.
The function was renamed to twl4030_power_mmc_init because all
the functions in this file are to have the format
twl4030_power_<device>_<action>
In this case the suffix is mmc_init so
device : mmc
action : init
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Because twl4030 now has its own device files, move exiting
omap3 power_init_r to a new location.
power_init_r is the only function in board/omap3/common.
It initializes the twl4030 power for the board and enables
the led.
The power part of the the function is moved to twl4030_power_init in
drivers/power/twl4030.c The power compilation is conditional on the
existing config variable CONFIG_TWL4030_POWER.
The led part is moved to twl4030_led_init in the new file
drivers/misc/twl4030_led.c The led compilation is conditional on
the new config variable CONFIG_TWL4030_LED
The directory board/omap3/common was removed because power_init_r
was the only function in it.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
Commit 2b3f12c2 added support for configurable SMC Rx buffer length on
8xx systems. Enable this feature on TQM8xx* based boards.
This fixes the problem that pasting text in the middle of a line
(i. e. inserting in edit mode) did not work - only the first two
characters got inserted, the rest was lost.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The Zoom2 power reset button is on the top right side of the
main board. Press and hold for about to 8 seconds to completely
reset the board.
Some of the beta boards have a hardware problem that prevents
using this feature. If is difficult to further characterize the
boards that fail. So disable resetting for all beta boards.
The Zoom1 reset button is the red circle on the top right,
front of the board. Press and hold the button for 8 seconds to
completely reset the board.
After analyzing beagle, it was determined that other boards
that use the twl4030 for power managment can also make use
this function.
The resetting is done by the power management part of the twl4030.
Since there is no existing drivers/power, add one.
The compilation of power/twl4030.h is controlled by the config
variable CONFIG_TWL4030_POWER
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Heiko Schocher <hs@denx.de>
DDR2 Auto-calibration needs to be disabled on the NAND booting PPC4xx
targets. Otherwise the configured fixed init values for some DDR2
controller registers (e.g. RQDC) are not initialized at all resulting
in a non working SDRAM.
Signed-off-by: Stefan Roese <sr@denx.de>
Board support for the Guntermann & Drunck CompactCenter and
DevCon-Center.
Based on the AMCC Canyonlands board support by Stefan Roese.
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds support for the esd VME8349 board equipped with the
MPC8349. It's a VME PMC carrier board equipped with the Tundra
TSI148 VME-bridge.
Signed-off-by: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Up to this point in time, the sbc8349 board was storing the u-boot
image in flash 2x. One for the HRCW value at the beginning of
flash (0xff80_0000), and once close to the end of flash (0xfff8_0000)
for the actual image that got executed.
This moves the TEXT_BASE to be the beginning of flash, which makes
the second copy of the image redundant, and frees up the flash
from the end of the environment storage to the end of the flash
device itself.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Commit 7024aa14 was supposed to fix the #ifdef/#endif pairing in
include/configs/at91cap9adk.h, but did not cate all problems.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch updates the support for EB+MCF-EV123 board and needs
the [PATCH 1/2 V3] new video driver for bus vcxk framebuffers
* remove the board framebuffer driver
* use the common bus_vcxk framebuffer driver
* adds bmp support
* adds splashimage support
* fix serveral cosmetical errors
Signed-off-by: Jens Scharsig <esw@bus-elektronik.de>
[agust@denx.de: fixed some style issues before applying]
Signed-off-by: Anatolij Gustschin <agust@denx.de>
This patch removes the "alterpll" command and replaces it with the now
ppc4xx standard "chip_config" command to configure the I2C bootstrap
EEPROM.
Signed-off-by: Stefan Roese <sr@denx.de>
Kilauea has an AT24C02 EEPROM which has an 8 byte page. Without defining
CONFIG_SYS_EEPROM_PAGE_WRITE_BITS to 3 the "eeprom" command doesn't
work correctly.
Additionally the page write delay (CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS)
is set to a more defensive value of 10ms.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds a generic command for programming I2C bootstrap
eeproms on PPC4xx. An implementation for Canyonlands board is
included.
The command name is intentionally chosen not to be PPC4xx specific.
This way other CPU's/SoC's can implement a similar command under
the same name, perhaps with a different syntax.
Usage on Canyonlands:
=> chip_config
Available configurations (I2C address 0x52):
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
600-nand - NAND CPU: 600 PLB: 200 OPB: 100 EBC: 100
800-nor - NOR CPU: 800 PLB: 200 OPB: 100 EBC: 100
800-nand - NAND CPU: 800 PLB: 200 OPB: 100 EBC: 100
1000-nor - NOR CPU:1000 PLB: 200 OPB: 100 EBC: 100
1000-nand - NAND CPU:1000 PLB: 200 OPB: 100 EBC: 100
1066-nor - NOR CPU:1066 PLB: 266 OPB: 88 EBC: 88 ***
1066-nand - NAND CPU:1066 PLB: 266 OPB: 88 EBC: 88
=> chip_config 600-nor
Using configuration:
600-nor - NOR CPU: 600 PLB: 200 OPB: 100 EBC: 100
done (dump via 'i2c md 52 0.1 10')
Reset the board for the changes to take effect
Other 4xx boards will be migrated to use this command soon
as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Dirk Eibach <eibach@gdsys.de>
Acked-by: Matthias Fuchs <matthias.fuchs@esd.eu>
The XPedite1000 is an X-ES product thus it can be put in board/xes along
with other X-ES boards. Along with the move, the board was renamed to
XPedite1000 from XPedite1K to fit X-ES's standard naming convention.
Maintainership was also transfered to Peter Tyser.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 only has 2 available ethernet ports:
ppc_4xx_eth2 (EMAC2) and ppc_4xx_eth3 (EMAC3)
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Previously an I2C EEPROM was used. The EEPROM had size, reliability,
and access issues which are resolved by storing the environment in
flash.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The XPedite1000 can be built with 4 total flashes:
- 512KB AMD socketed
- 16MB Intel soldered
- 2 x 32MB AMD MirrorBit flashes
Add support for the optional 2 32MB CFI-compliant AMD flashes
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
By default, the XPedite1000 comes installed with xMon, a proprietary
bootloader. xMon stores its MAC address in an onboard EEPROM. Rather
than requiring a non-standard location in the EEPROM to be reserved for
MAC addresses, store the MAC addresses in U-Boot's standard environment.
A U-Boot application or OS application can be used to migrate xMon MAC
addresses to U-Boot's environment if necessary.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Using the CFI flash driver will allow write access to the 16MB Intel
StrataFlash present on the XPedite1000. The 512KB socketed (non
CFI-compliant flash) will no longer be writable.
The mapping of the 16MB Strata flash was moved to 0xff000000 and the
512KB AMD socketed flash was moved to 0xfe000000.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds I2C support for mvBC-P and defines flash layout
matching the shipped product.
Signed-off-by: Andr Schwarz <andre.schwarz@matrix-vision.de>
All in-tree boards that use this controller have CONFIG_NET_MULTI added
Also:
- changed CONFIG_DRIVER_SMC911X* to CONFIG_SMC911X*
- cleaned up line lengths
- modified all boards that override weak function in this driver
- added
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Tested-by: Mike Frysinger <vapier@gentoo.org>
This is Marvell's 88F6281_A0 based reference design board
This patch is tested for-
1. Boot from DRAM/NAND flash/NFS
2. File transfer using tftp and loadb
3. NAND flash read/write/erase
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Use the MPC8572's eLBC to access 1 GB (or greater) onboard NAND flash
via the 'nand' command.
Previously, the XPedite5370's NAND chip selects were properly
configured, but NAND support was not enabled.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Increasing CONFIG_SYS_BOOTM_LEN from 8 MB to 16 MB is necessary to
support uncompressing images larger than 8 MB when using the bootm
command.
Note that recent Linux kernels for the 85xx and 86xx map greater than
16MB of memory on bootup, but we use 16MB to maintain compatibility with
older Linux kernels for now.
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Buffered writes are possible on the XPedite5200 and XPedite5370 and greatly
improve NOR flash write speeds
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The p2020DS, MPC8536DS, MPC8572DS, MPC8544DS boards are capable of
swizzling the upper address bits of the NOR flash we boot out of which
creates the concept of "virtual" banks. This is useful in that we can
flash a test of image of u-boot and reset to one of the virtual banks
while still maintaining a working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The MPC8641HPCN board is capable of swizzling the upper address bit of
the NOR flash we boot out of which creates the concept of "virtual"
banks. This is useful in that we can flash a test of image of u-boot
and reset to one of the virtual banks while still maintaining a
working image in "bank 0".
The PIXIS FPGA exposes registers on LBC which we can use to determine
which "bank" we are booting out of (as well as setting which bank to
boot out of).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
A large number of boards (all AT91 based) duplicated the ROUND()
macro in their board specific config files. Add the definition to
include/common.h and clean up the board config files.
Signed-off-by: Wolfgang Denk <wd@denx.de>
We have always mapped at least 16M in the kernel and we have seen cases
with new kernel features that a kernel image needs more than 8M of
memory.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_MALLOC_LEN is defined in the board config, and
the keymile-common.h, which collects common options used
by all keymile-boards. This results in a compile error
when compiling the kmeter1 board. So remove this define
in the board config file.
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch adds the possibility to call a board specific
i2c bus reset routine for the fsl_i2c bus driver, and adds
this option for the keymile kmeter1 board.
The deblock sequence for this board is implemented and
tested in the following way:
CR = 0x20 (release SDA and SCL pin)
CR = 0xa0 (start read)
dummy read
dummy read
if 2. dummy read == 0x00
3. dummy read
CR = 0x80 (SDA and SCL now 1 SR = 0x86)
CR = 0x00 (Modul reset SR=0x81)
CR = 0x80 (SDA and SCL = 1, SR = 0x81)
Signed-off-by: Heiko Schocher <hs@denx.de>
- CONFIG_SYS_MAX_I2C_BUS changed to 1
We use only one I2C hardwarecontroller on this boards, so
change the CONFIG_SYS_MAX_I2C_BUS to 1.
- common: dont print errormsg if second IVM Block lacks.
- 82xx, mgcoge: fix double mtdpart entry in environment
- 82xx, mgcoge: activate on second Flash the second bank.
- common: CONFIG_ENV_SIZE 0x4000 for all keymile boards
- common: Change malloc size to 1MByte for all Keymile boards
We need a bigger malloc area for the environment support (128k)
on some Keymile boards (kmeter1) and the upcoming UBI support.
Change it to 1MB for all Keymile boards to be on the save side.
Also define CONFIG_SYS_64BIT_VSPRINTF which is needed for
UBI/UBIFS support.
- Add UBI support to all Keymile boards
- change manner of writing "/localbus/ranges" node
instead of writting the complete "/localbus/ranges" node
before booting Linux, only update the ranges entries
which gets dynamical detected (size of flashes).
This is needed, because keymile adds in the DTS
"/localbus/ranges" node entries, which u-boot must
not overwrite/delete.
- kmeter, mgcoge: define 2 seperate regions needed for the Intel P30 chips
The Intel P30 chip has 2 non-identical chips on
one die, so we need to define 2 seperate regions
that are scanned by physmap_of independantly.
- kmeter1: Add MTD concat support to Keymile boards
- 82xx, mgcoge: add "unlock=yes" to default environment
- added CONFIG_MTD_DEVICE to get in sync with mainline code
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 2419169f removed support for legacy NAND and disk on chip but
missed to update the code for a few boards. This patch fixes the
resulting build issues.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch adds a SATA harddisk driver for the canyonlands.
This patch is kernel driver's porting.
This patch corresponded to not cmd_scsi but cmd_sata.
This patch divided an unused member with ifndef __U_BOOT__ in the structure.
[environment variable, boot script]
setenv bootargs root=/dev/sda7 rw
setenv bootargs ${bootargs} console=ttyS0,115200
ext2load sata 0:2 0x400000 /canyonlands/uImage
ext2load sata 0:2 0x800000 /canyonlands/canyonlands.dtb
fdt addr 0x800000 0x4000
bootm 0x400000 - 0x800000
If you drive SATA-2 disk on Canyonlands, you must change parts from
PI2PCIE212 to PI2PCIE2212 on U25. We confirmed to boot by using
following disks:
1.Vendor: Fujitsu Type: MHW2040BS
2.Vendor: Fujitsu Type: MHW2060BK
3.Vendor: HAGIWARA SYS-COM:HFD25S-032GT
4.Vendor: WesternDigital Type: WD3200BJKT (CONFIG_LBA48 required)
5.Vendor: WesternDigital Type: WD3200BEVT (CONFIG_LBA48 required)
6.Vendor: Hitachi Type: HTS543232L9A300 (CONFIG_LBA48 required)
7.Vendor: Seagate Type: ST31000333AS (CONFIG_LBA48 required)
8.Vendor: Transcend Type: TS32GSSD25S-M
9.Vendor: MTRON Type: MSD-SATA1525-016
Signed-off-by: Kazuaki Ichinohe <kazuichi at fsi.co.jp>
While the 1.0 and 1.2 spin of the bf533-stamp boards can handle the higher
SCLK speeds just fine, the 1.1 spin cannot due to the bugs introduced with
the shortened SDRAM traces. So lower the SCLK speed down to a value that
all three can handle.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
This patch covers the non-PPC boards that were missed in the previous
patch (commit 170c1972).
Signed-off-by: Wolfgang Denk <wd@denx.de>
This is Marvell's 88F6281_A0 based custom board developed
for wireless access point product
This patch is tested for-
1. Boot from DRAM/SPI flash/NFS
2. File transfer using tftp and loadb
3. SPI flash read/write/erase
4. Booting Linux kernel and RFS from SPI flash
5. Boot from USB supported
Reviewed-by: Ronen Shitrit <rshitrit@marvell.com>
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Reference:
http://plugcomputer.org/http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
5. Enabled USB PHY init for kernel need
6. Boot from USB supported
Note: to boot Kirkwood kernel with USB support,
you should add "usb start" in the boot sequence
Signed-off-by: Prafulla Wadaskar <prafulla@marvell.com>
Commit 8d2effea added a warning for configurations that use NAND
without defining the (then necessary) CONFIG_SYS_64BIT_VSPRINTF but
failed to fix the affected boards.
Signed-off-by: Wolfgang Denk <wd@denx.de>
So far the console API uses the following naming convention:
======Extract======
typedef struct device_t;
int device_register (device_t * dev);
int devices_init (void);
int device_deregister(char *devname);
struct list_head* device_get_list(void);
device_t* device_get_by_name(char* name);
device_t* device_clone(device_t *dev);
=======
which is too generic and confusing.
Instead of using device_XX and device_t we change this
into stdio_XX and stdio_dev
This will also allow to add later a generic device mechanism in order
to have support for multiple devices and driver instances.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Edited commit message.
Signed-off-by: Wolfgang Denk <wd@denx.de>
This patch simply converts the board to the hwconfig infrastructure.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
fdt_fixup_esdhc() will either disable or enable eSDHC nodes, and
also will fixup clock-frequency property.
Plus, since DR USB and eSDHC are mutually exclusive, we should
only configure the eSDHC if asked through hwconfig.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Cc: Dave Liu <daveliu@freescale.com>
Cc: Ron Madrid <ron_madrid@sbcglobal.net>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Remove individual CPU specific DSPI driver.
Add required feature for the common DSPI driver in cpu_init and
in platform configuration file.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Update serial boot DRAM's Internal RAM, vector table and DRAM in
start.S, serial flash's read status command over SPI and NOR
flash.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Remove dead code that was obviously a left-over from copy & paste.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
When enabling NAND support for a board, one must also define
CONFIG_SYS_64BIT_VSPRINTF because this is needed in nand_util.c
for correct output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
AT91sam9g10 is an ARM 926ej-s SOC. It is an evolution of the at91sam9261 with a
faster clock speed: 266/133MHz.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
AT91sam9g45 series is an ARM 926ej-s SOC family clocked at 400/133MHz.
It embeds USB high speed host and device, LCD, DDR2 RAM, and a full set of
peripherals.
The first board that embeds at91sam9g45 chip is the AT91SAM9G45-EKES.
On the board you can find 2 USART, USB high speed,
a 480*272 LG lcd, ethernet, gpio/joystick/buttons.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
ESPT-Giga is SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet
driver, but the code that used that macro was removed over a year
ago, so board configuration files no longer need to define it.
The _IO_BASE macro is also automatically defined to 0 if it isn't
already set, so there's no need to define that macro either in the
board configuration files.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Acked-by: Andre Schwarz <andre.schwarz@matrix-vision.de>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Add support for the Phytec phyCORE-MPC5200B-tiny.
Code originally from Pengutronix.de.
Created CONFIG_SYS_ATA_CS_ON_TIMER01 define for when IDE CS is on
Timer 0/1
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
The cm-bf561 module can easily hook up to the EXT-BF5xx-USB-ETH2 extender
board, so add a simple example of how to do that in the board config.
Signed-off-by: Harald Krapfenbauer <Harald.Krapfenbauer@bluetechnix.at>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest blackstamp boards can only run the SPI flash at 15MHz before
they start to crap out, so lower the max speeds accordingly. The new SPI
flash also has different sector requirements, so update the environment
sizes as well.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch fixes 2 problems with FDT EBC mappings on Canyonlands.
First, NAND EBC mapping was missing, making Linux NAND driver
unusable on this board. Second, NOR remapping code assumed that
NOR is always on CS0, however when booting from NAND NOR is on CS3.
Signed-off-by: Felix Radensky <felix@embedded-sol.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Currently, when booting from NAND using nand_spl, in the beginning the default
environment is used until later in boot process the dynamic environment is read
out. This way environment variables that must be interpreted early, like the
baudrate or "silent", cannot be modified dynamically and remain at their
default values. Fix this problem by reading out main and redundand (if used)
copies of the environment in the nand_spl code.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
The BF537-STAMP Blackfin board had a driver for working with NAND devices
that are simply memory mapped. Since there is nothing Blackfin specific
about this, generalize the driver a bit so that everyone can leverage it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Scott Wood <scottwood@freescale.com>
This sets CONFIG_SYS_HZ to 1000 as required, and completely rewrites
timer code, which is now both correct and much smaller. Unused
functions like udelay_masked() have been removed as no driver uses
them, even the ones that are not currently active for this board.
mtu.h is copied literally from the kernel sources.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The evaluation kit has both Nand and OneNand, both drivers are there
and the two configurations only select a different default for the
jffs partition. This adds the OneNand driver and cleans up storage.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
There is only one public release of the Nomadik chip, so the ifdef
in reset code as well as a define in the config file are not needed
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This is an error in my side in the initial submission: nobody
calls it ""nmdk8815", it's "nomadik hardware kit", nhk8815, instead.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stericsson.com>
This patch adds support for esd gmbh MEESC board.
The MEESC is based on an Atmel AT91SAM9263 SoC.
Signed-off-by: Daniel Gorsulowski <Daniel.Gorsulowski@esd.eu>
Add support for Freescale's i.MX31 PDK board (a.k.a. 3 stack board).
This patch assumes that some other program performs the actual
NAND boot.
Signed-off-by: Magnus Lilja <lilja.magnus@gmail.com>
Acked-by: Fabio Estevam <fabioestevam@yahoo.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Initial support for Extreme Engineering Solutions XPedite5170 -
a MPC8640-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
DMA support is now enabled via the CONFIG_FSL_DMA define instead of the
previous CONFIG_DDR_ECC
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We want the outbound PCI memory map to end at the 4G boundary so we
can maximize the amount of space available for inbound mappings if
we have large amounts of memory.
This matches the device tree setup in the kernel for the 36-bit physical
configs for the platforms that have one (MPC8641 HPCN & MPC8572 DS).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
UART hardware on i.MX27 is the same as on the i.MX31 so we just
need to provide the driver with correct address of the registers.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
this will allow you to store use it for the env and to boot directly U-Boot from
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The PM9261 board is based on the AT91SAM9261-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9261.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
move PSRAM init to pm9263.c
this will allow us after to make the nor lowlevel_init generic
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
The SPI flash define is named CONFIG_SF_DEFAULT_SPEED, not
CONFIG_SF_DEFAULT_HZ, so fix the typos in the Blackfin boards.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The latest version of U-Boot got a bit fatter in the BSS section which
caused overflows in the RAM region, so increase the monitor size.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The SPI flash layer is much stricter about sector usage than the eeprom
layer we used to use, so update the env settings to better match the
sector alignment of the flashes we use.
Signed-off-by: Vivi Li <vivi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
All drivers need to be converted to CONFIG_NET_MULTI.
This patch converts the dm9000 driver.
Signed-off-by: Thomas Smits <ts.smits@gmail.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
Added CONFIG_NET_MULTI to all Davinci boards
Removed all calls to Davinci network driver from board code
Added cpu_eth_init() to cpu/arm926ejs/cpu.c
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
All the Blackfin linker scripts were duplicated across the board dirs with
no difference save from the semi-often used ENV_IS_EMBEDDED option. So
unify all of them in the lib_blackfin/ dir and for the few boards that
need to embedded the environment directly, add a LDS_BOARD_TEXT define for
them to customize via their board config file. This is much simpler than
forcing them to duplicate the rest of the linker script.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The BF51xF parts have an internal SST SPI flash, so make sure the driver is
enabled by default so we can access it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
The Blackfin port was using asm/blackfin-config-{pre,post}.h to setup
common Blackfin board defines. The common method now is to use config.h,
so convert blackfin-config-post.h to that. Rename the still Blackfin
specific blackfin-config-pre.h to config-pre.h so the naming conventions
at least line up.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Allow boards to easily override the root= and default bootcmd, allow
people to tweak the file used in default bootcmds at runtime via one env
var, and add a stock nandboot command.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Newer Blackfin parts can an on-chip ROM that can boot LDRs over SPI flashes,
so add a new 'spibootldr' command to take advantage of it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
On MPC8569MDS board, UCC6 and UCC8 can be configured to work at SGMII mode via
UEM on PB board. Since MPC8569 supports up to 4 Gigabit Ethernet ports, we
disable UEC6 and UEC8 by default.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch supports UCC working at RMII mode on PIB board, fixup fdt blob to
support rmii in kernel. It also changes the name of enable_mpc8569mds_qe_mdio to
enalbe_mpc8569mds_qe_uec which is more accurate.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch adds support for P2020DS reference platform.
DDR3 interface uses hard-coded initialization rather than SPD
for now and was tested at 667Mhz. Some PIXIS register
definitions and associated code sections need to be fixed.
TSEC1/2/3, NOR flash, MAC/SYS ID EEPROM, PCIE1/2/3 are all
tested under u-boot.
Signed-off-by: Srikanth Srinivasan <srikanth.srinivasan@freescale.com>
Signed-off-by: Travis Wheatley <Travis.Wheatley@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds NAND support to the MPC5121ADS board. Please
note that the image size increased since NAND support didn't
fit in the current image size (256k).
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
The CPCI750 can be built as CPCI host or adapter/target board. This patch
adds support for runtime detection of those variants.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Reinhard Arlt <reinhard.arlt@esd-electronics.com>
This patch adds CONFIGs for enabling USB in mpc8536ds and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
This patch adds CONFIGs for enabling USB in mpc8315erdb and also
adds usb_phy_type in CONFIG_EXTRA_ENV_SETTINGS. Also revamps its
Copyright.
Signed-off-by: Vivek Mahajan <vivek.mahajan@freescale.com>
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Move needed definitions (register descriptions etc.) from
include/mpc512x.h into include/asm-ppc/immap_512x.h.
Instead of using a #define'd register offset, use a function that
provides the PATA controller's base address.
All the rest of include/mpc512x.h are register offset definitions
which can be eliminated by proper use of C structures.
There are only a few register offsets remaining that are needed in
cpu/mpc512x/start.S; for these we provide cpu/mpc512x/asm-offsets.h
which is intended as a temporary workaround only. In a later patch
this file will be removed, too, and then auto-generated from the
respective C structs.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
We rename the board so we use a consistent name in U-Boot and in
Linux. Also, we use this opportunity to move the board into the
Freecale vendor directory.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: John Rigby <jcrigby@gmail.com>
The kernel stores address<->symbol names in it so things can be decoded at
runtime. Do it in U-Boot, and we get nice symbol decoding when crashing.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
By changing the cmd_mtdparts to only use the MTD infrastructure and
not the direct interface to the CFI NOR FLASH driver we now need
to add the MTD infrastructure to all boards using those mtdparts
commands. This patch adds those components:
CONFIG_MTD_DEVICE (for all FLASH types)
plus
CONFIG_FLASH_CFI_MTD (for NOR FLASH)
To all board maintainers: Please test this on your platforms and
report any problems/issues found. Thanks.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Ron Madrid <info@sheldoninst.com>
Cc: Georg Schardt <schardt@team-ctech.de>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ladislav Michl <ladis@linux-mips.org>
Cc: Martin Krause <martin.krause@tqs.de>
Cc: Gary Jennejohn <garyj@denx.de>
Cc: Ricardo Ribalda <ricardo.ribalda@uam.es>
Enable the function and interface clocks for banks 2,3,5 and 6.
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Acked-by: Dirk Behme <dirk.behme@googlemail.com>
With other OMAP3 boards we recently switched to CPU and Board
info API. From parallel merge, this is missing for Zoom2.
Enable it for Zoom2, too.
Signed-off-by: Dirk Behme <dirk.behme@googlemail.com>
Acked-by: Tom Rix <Tom.Rix@windriver.com>
Zoom2 serial is in general supplied by one of the 4 UARTS on the debug board.
The default serial is from the USB connector on left side of the debug board.
The USB connector will produce 2 of the 4 UARTS. On your host pick the first
enumeration.
The details of the setting of the serial gpmc setup are not available.
The values were provided by another party.
The serial port set up is the same with Zoom1.
Baud rate 115200, 8 bit data, no parity, 1 stop bit, no flow.
The kernel bootargs are
console=ttyS3,115200n8
Signed-off-by: Tom Rix <Tom.Rix@windriver.com>
Also enable display of 'E'mpty sectors in "flinfo" output.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Also reserve more space for U-Boot as it will probably grow soon.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Initial U-Boot support for the DaVinci DM355 EVM. This is a board
from Spectrum Digital. Board docs include schematic and firmware
for its microcontroller:
http://c6000.spectrumdigital.com/evmdm355/revd/
Most of the DM355 chip is fully documented by TI, the most notable
exception being the MPEG/JPEG coprocessor (programmable using codecs
available at no cost from TI), which is omitted from its DM335 sibling:
http://focus.ti.com/docs/prod/folders/print/tms320dm355.html
This version can boot from the on-board DM9000 Ethernet chip, after
being loaded (from NAND, MMC/SD, or UART). In the near future, NAND
and USB support could be added ... NAND support is being held back
until the support for the 4-bit ECC hardware is ready.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The current configuration doesn't define default
bootfile; leading to this warning at execution:
OMAP3_EVM # dhcp
...
...
DHCP client bound to address 192.168.1.11
*** Warning: no boot file name; using 'AC18BE16.img'
TFTP from server 0.0.0.0; our IP address is 192.168.1.11;
sending through gateway 192.168.1.1
Filename 'AC18BE16.img'.
Load address: 0x82000000
Loading: *
TFTP error: 'File not found' (1)
Signed-off-by: Sanjeev Premi <premi@ti.com>
This updates the optional (non-default!) NAND support for the
DaVinci DM6446 EVM:
- include MTD partitioning, defaulting to what Linux uses
- use a flash-based BBT, which among other things speeds bootup
This matches code that's now queued for mainline Linux, and might
even merge in an upcoming 2.6.30-rc; and the MTIDS are set up so
that the U-Boot $mtdparts environment variable can be passed as-is
on the kernel command line as a cmdlinepart override.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Move the clock-rate dumping code into the cpu/.../davinci area
where it should have been, enabled by CONFIG_DISPLAY_CPUINFO,
updating the format and showing the DSP clock (where relevant).
Switch boards to use the cpuinfo() hook for this stuff.
Remove a few now-obsolete PLL #defines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
actually the timer init use the interrupt_init as init callback
which make the interrupt and timer implementation difficult to follow
so now rename it as int timer_init(void) and use interrupt_init for interrupt
btw also remane the corresponding file to the functionnality implemented
as ixp arch implement two timer - one based on interrupt - so all the timer
related code is moved to timer.c
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Split out DaVinci DM6446-specific bits from more generic bits:
- Add a CONFIG_SOC_DM644X. All current boards use DM6446 chips;
DM6443 and DM6441 chips differ in available peripherals.
- Move most DM644X-specific bits from psc.c to a new dm644x.c file,
which is conditionally built. It provides device-specific setup.
Plus minor coding style and comment updates with respect to the PSC.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
This patch adds another build target for the AMCC Sequoia PPC440EPx
eval board. This RAM-booting version is targeted for boards without
NOR FLASH (NAND booting) which need a possibility to initially
program their NAND FLASH. Using a JTAG debugger (e.g. BDI2000/3000)
configured to setup the SDRAM, this debugger can load this RAM-
booting image to the target address in SDRAM (in this case 0x1000000)
and start it there. Then U-Boot's standard NAND commands can be
used to program the NAND FLASH (e.g. "nand write ...").
Here the commands to load and start this image from the BDI2000:
440EPX>reset halt
440EPX>load 0x1000000 /tftpboot/sequoia/u-boot.bin
440EPX>go 0x1000000
Please note that this image automatically scans for an already
initialized SDRAM TLB (detected by EPN=0). This TLB will not be
cleared. This TLB doesn't need to be TLB #0, this RAM-booting
version will detect it and preserve it. So booting via BDI2000
will work and booting with a complete different TLB init via
U-Boot works as well.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on DP405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on VOM405 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on PMC405 boards.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch removes the cpld binary bitstream that is
used by esd's cpld command on CMS700 boards.
Because u-boot with an external cpld bitstream may not
take more space in flash than before the u-boot binary is
shrinked a little bit. Some unused featues have been
removed therefore.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
The individual i2c commands imd, imm, inm, imw, icrc32, iprobe, iloop,
and isdram are no longer available so all references to them have been
updated to the new form of "i2c <cmd>".
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
The following individual I2C commands have been removed: imd, imm, inm,
imw, icrc32, iprobe, iloop, isdram.
The functionality of the individual commands is still available via
the 'i2c' command.
This change only has an impact on those boards which did not have
CONFIG_I2C_CMD_TREE defined.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Add standard CONFIG_SYS_I2C_SPEED define for the mpc7448hpc2 so that
it can use the common 'i2c speed' command. Note that the I2C controller
utilized by the mpc7448hpc2 has a fixed speed and cannot be changed
dynamically.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Yu Liu <Yu.Liu@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Increase the size of malloc to 512KB because MPC8569MDS needs more memory for
malloc to support up to eight Ethernet interfaces.
- Move Environment address out of uboot thus the saved environment variables
will not be erased after u-boot is re-programmed.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove "saveenv" from "update" definition: the environment is outside
the U-Boot image on TQM85xx and therefor not affected by updates.
Also "beautify" code a bit (vertical alignment).
Signed-off-by: Wolfgang Denk <wd@denx.de>
Old TQM85xx boards had 'M' type Spansion Flashes from the S29GLxxxM
series while new boards have 'N' type Flashes from the S29GLxxxN
series, which have bigger sectors: 2 x 128 instead of 2 x 64 KB.
We now change the configuration to the new flash types for all
boards; this also works on old boards - we just waste two flash
sectors for the environment which could be smaller there.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The SYS_CLK_IN of MPC8569MDS is 66.66MHz,
The DDR_CLK_IN is same with SYS_CLK_IN in 8569 processor.
so, change the SYS_CLK_IN from 66MHz to 66.66MHz.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Some boards do not have SROM support for the DM9000 network adapter.
Instead of listing these board names in the driver code, make this
option configurable from the board config file.
It also removes a build warning for the at91sam9261ek board:
'dm9000x.c:545: warning: 'read_srom_word' defined but not used'
And it repaires the trizepsiv board build which was broken around the
same routines
Signed-off-by: Remy Bohmer <linux@bohmer.net>
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
In GMII mode (which operates at 3.3V) both SICRH TSEC1/2 output buffer
impedance bits should be clear, i.e., SICRH[TSIOB1] = 0 and SICRH[TSIOB2] = 0.
SICRH[TSIOB1] was erroneously being set high.
U-Boot always operated this PHY interface in GMII mode. It is assumed this
was missed in the clean up by the original board porters, and copied along
to the TQM and sbc boards.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Ira Snyder <iws@ovro.caltech.edu>
Reviewed-by: David Hawkins <dwh@ovro.caltech.edu>
Tested-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Dave Liu <DaveLiu@freescale.com>
The pins for async memory where parallel flash lives are not enabled by
default, so make sure we mux them as needed.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Add CONFIG_SYS_MONITOR_LEN macro to apollon board config.
CONFIG_SYS_MONITOR_LEN defines the U-Boot image size.
and is used by OneNAND ipl when reading U-Boot image.
Signed-off-by: Rohit Hagargundgi <h.rohit at samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
The pin which was used in preliminary versions of the board for ide
reset is really connected to the rtc clock.
Signed-off-by: Detlev Zundel <dzu@denx.de>
The BF527-EZKIT settings for storing the environment in SPI flash wasn't
using the correct sector settings for the SPI flash part that is actually
on the board.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Let CONFIG_SYS_HZ to have value of 1000 effectively fixing all users of
get_timer.
Changes since original version:
* Set PTV=2 (divisor 8) for boards using 12MHz timer clock source to
improve timer resolution.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Use the functions print_cpuinfo() and checkboard() to
display the cpu and board specific information.
These functions reuse content from the existing function
display_board_info() - which has been removed.
Also, updated the existig OMAP3 configurations to
define:
- CONFIG_DISPLAY_CPUINFO
- CONFIG_DISPLAY_BOARDINFO
Signed-off-by: Sanjeev Premi <premi@ti.com>
because legacy NAND support is deprecated converting to current
NAND interface. !This just compile, because I have no more the
hardware to test it.
Signed-off-by: Heiko Schocher <hs@denx.de>
As the common code also handles baudrate switching, which the board
specific vct.c driver did not support, this is one of the rare
occassions where deleting code actually adds a feature :)
Signed-off-by: Detlev Zundel <dzu@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Minor cleanup to clock-related defines for DaVinci DM6446 boards:
- CONFIG_SYS_CLK_FREQ is unused; remove it.
- CONFIG_SYS_NS16550_CLK must be the same as CONFIG_SYS_HZ_CLOCK
On DM6446 both of those peripheral clocks actually come from the
same source, the primary oscillator. Having them use the same
symbol avoids bugs in the clone'n'modify development cycle.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The size of U-Boot binary for MPC8360ERDK increased
(> 2 flash sectors now), so 'saveenv' will partially
overwrite U-Boot in flash and will brick the board.
This patch moves environment offset to fourth flash
sector and also fixes CONFIG_SYS_MONITOR_LEN.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Update the DaVinci DM6446 boards to use the new convention
for CONFIG_SYS_NS16550_REG_SIZE ... the size hasn't changed
from the original 4 bytes, but these chips are little-endian.
(Resolves a regression added recently by the include/ns16550.h
patch to "Unify structure declaration for registers". The code
previously worked just fine because the registers were accessed
as host-endian words, not as bytes.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
The timer has been rewrote with a precision at ~0,18%
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Tested-by: Sergey Lapin <slapin@ossfans.org>
Tested-by: Eric BENARD <ebenard@free.fr>
The PM9263 board is based on the AT91SAM9263-EK board.
Here is the page on Ronetix website:
http://www.ronetix.at/starter_kit_9263.html
Signed-off-by: Ilko Iliev <iliev@ronetix.at>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Don't run the memory POST on the NAND-booting version. It will
overwrite part of the U-Boot image which is already loaded from NAND
to SDRAM. We were just lucky that it booted at all with this SDRAM
test enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
The AT91RM9200-EK Evaluation Board supports the AT91RM9200
ARM9-based 32-bit RISC microcontroller and enables real-time code development
and evaluation.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/tools_card.asp?tool_id=3507
with
- NOR (cfi driver)
- DataFlash
- USB OHCI
- Net
- I2C (hard)
Signed-off-by: Ulf Samuelsson <ulf@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
According to the doc/feature-removal-schedule.txt, the "autoscr"
command will be replaced by the "source" command in approximately 6
months from now.
This patch prepares this change and starts a 6 month transition
period as follows:
- The new "source" command has been added, which implements exactly
the same functionlaity as the old "autoscr" command before
- The old "autoscr" command name is kept as an alias for compatibility
- Command sequences, script files atc. have been adapted to use the
new "source" command
- Related environment variables ("autoscript", "autoscript_uname")
have *not* been adapted yet; these will be renamed resp. removed in
a separate patch when the support for the "autoscr" command get's
finally dropped.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The mpc8313erdb board currently sets DBAT6 to cover all of the final 256MiB of
address space; however, not all of this space is covered by a device. In
particular, flash sits at 0xfe000000-0xfe7fffff, and nothing is mapped
at the far end of the address space.
In zlib, there is a loop that references p[-1] if p is non-NULL. Under
some circumstances, this leads to the CPU speculatively loading from
0xfffffff8 if p is NULL. This leads to a machine check.
Signed-off-by: Scott Wood <scottwood@freescale.com>
continuation to the remaining mpc83xx boards that suffer from the same problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Use CONFIG_MP instead of CONFIG_NUM_CPUS to match 85xx
* Introduce determine_mp_bootpg() helper. We'll need this to address a
bug introduced in v2009.03 with 86xx MP booting. We have to make sure
to reserve the region of memory used for the MP bootpg() so other
u-boot code doesn't use it.
* Added dummy versions of cpu_reset(), cpu_status() & cpu_release() to
allow cmd_mp.c to build and work. In the future we should look at
implementing all these functions. This could be common w/85xx if we
use spin tables on 86xx.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds MPC8569MDS board support. The UART, QE UEC1 and UEC2, BRD
EEPROM on I2C2 bus, PCI express and DDR3 SPD are supported in this patch.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Hillel Avni <Hillel.Avni@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Divisor field is called PTV not PVT.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
This patch adds the board specific communication routines needed by
the external 4543 RTC.
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Andreas Pfefferle <ap@denx.de>
This patch adds advanced diagnosis functions for the inka4x0 board.
Signed-off-by: Andreas Pfefferle <ap@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Current u-boot top of tree builds with warnings/errors for
the following boards:
ads5121 cpci5200 mecp5200 v38b IAD210 MBX MBX860T NX823
RPXClassic debris PN62
following patch solves this.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Enabling the instruction cache significantly accelerates U-Boot
operations like CRC checking, image uncompression, etc.
Kudos to Andrea Scian for pointing out.
Signed-off-by: Wolfgang Denk <wd@denx.de>
http://www.denx.de/wiki/DULG/UBootCmdGroupFlash#UBootCmdFlMtdparts
provides a flexible way to create and maintain u-boot mtd
partitions. This allows commands such as "nand erase fs"
to work and the user no longer needs to decode the absolute
nand offsets. This patch enables this function for beagleboard
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Since all of the bf537-stamp and bf537-ezkit boards out there can handle it,
increase the speed of SCLK to 125MHz rather than 100MHz.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Since the hardware can handle it, bump the default clocks from 80mhz SCLK
and 398mhz CCLK to 100mhz SCLK and 498mhz CCLK.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Again, don't clobber pins that we aren't actually using, and use the common
LED framework rather than our own hob-job-but-not-really-working.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Rather than duplicate the same ADI settings in every ADI board, create a
common ADI config header and have all ADI boards start using that. This
will also make merging the ~10 boards I have to forward port a lot easier.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patches configures the NAND UPM-FSL driver with multi-chip
support for the Micron MT29F8G08FAB NAND flash memory on the
TQM8548 modules.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
AT91sam9g20 is an evolution of the at91sam9260 with a faster clock speed.
The AT91SAM9G20-EK board is an updated revision of the AT91SAM9260-EK board.
It is essentially the same, with a few minor differences.
Here is the chip page on Atmel website:
http://www.atmel.com/dyn/products/product_card.asp?part_id=4337
Signed-off-by: Justin Waters <justin.waters@timesys.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
This patch replaces in/out8/16/32 macros by in/out_8/_be16/_be32
macros. Also volatile pointer references are replaced by the
new accessors.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix building DASA_SIM boards by increasing U-Boot's size in flash.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: Stefan Roese <sr@denx.de>
Rewrite interrupt handling functionality for the i386 port. Separated
functionality into separate CPU and Architecture components.
It appears as if the i386 interrupt handler functionality was intended
to allow multiple handlers to be installed for a given interrupt.
Unfortunately, this functionality was not fully implemented and also
had the problem that irq_free_handler() does not allow the passing
of the handler function pointer and therefore could never be used to
free specific handlers that had been installed for a given IRQ.
There were also various issues with array bounds not being fully
tested.
I had two objectives in mind for the new implementation:
1) Keep the implementation as similar as possible to existing
implementations. To that end, I have used the leon2/3
implementations as the reference
2) Seperate CPU and Architecture specific elements. All specific i386
interrupt functionality is now in cpu/i386/ with the high level
API and architecture specific code in lib_i386. Functionality
specific to the PC/AT architecture (i.e. cascaded i8259 PICs) has
been further split out into an individual file to allow for the
implementation of the PIC architecture of the SC520 CPU (supports
more IRQs)
Signed-off-by: Graeme Russ <graeme.russ at gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Also rename load_sernum_ethaddr() to misc_init_r() so we don't need to
handle this board specially in common ARM code.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
The environment is the canonical storage location of the mac address, so
we're killing off the global data location and moving everything to
querying the env directly.
Rather than have the common ppc code have board-specific hooks, move the
board_get_enetaddr() function into the board-specific init functions.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
CC: Ben Warren <biggerbadderben@gmail.com>
Total5200 and digsy MTC use I2C port 2 pins as a ATA chip select.
To avoid adding board-specific ifdefs to cpu/mpc5xxx/ide.c new
define CONFIG_SYS_ATA_CS_ON_I2C2 was introduced. It is used by
Total5200 and will be used by digsy MTC and other boards with
ATA CS on I2C pins.
Signed-off-by: Grzegorz Bernacki <gjb@semihalf.com>
This patch adds support for the kmsupx4 board from Keymile,
based on a Freescale MPC852T CPU
- serial console on SMC1
- 32 MB SDRAM
- 32 MB NOR Flash
- Ethernet over SCC3
- I2C Bitbang
Signed-off-by: Heiko Schocher <hs@denx.de>
renaming the "mgsuvd" board port into "km8xx", because
there come more similar boards from keymile.
Compiling the mgsuvd board with "make mgsuvd_config"
remains.
Signed-off-by: Heiko Schocher <hs@denx.de>
- added to keymile-common.h:
- bootcount support
- COMMAND HISTORY
- CONFIG_AUTO_COMPLETE
- CONFIG_SYS_FLASH_PROTECTION
- JFFS2 support
- CONFIG_VERSION_VARIABLE
- extracted common I2C settings for all boards
- common default environment settings summarized
Signed-off-by: Heiko Schocher <hs@denx.de>
The rtl8139 driver use pci_mem_to_phys. So it need PCI system memory
registration.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We can built 'make sh7785lcr_32bit_config'. And add new command "pmb"
for this mode. This command changes PMB for using 512MB system memory.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Some register value was hardcoded for System memory size 128MB and
memory offset 0x08000000. This patch fixed the problem.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
it is possible that some board variants have different DDR II
RAM sizes. So we autodetect the size of the assembled RAM.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds I2C support for the Keymile kmeter1 board.
It uses the First I2C Controller from the CPU, for
accessing 4 temperature sensors, an eeprom with IVM data
and the booteeprom over a pca9547 mux.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The previous version rebooted forever with DDR bigger than 256MB.
Access the DS1339 RTC chip is on I2C1 bus.
Allow DHCP.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The "eet" variant of the imx31_phycore board has an OLED display, using a
s6e63d6 display controller on the first SPI interface, using GPIO57 as a
chip-select for it. With this configuration you can display 256 colour BMP
images in 16-bit RGB (RGB565) LCD mode.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This trivially enables Ethernet support in the debug board
by setting up the proper chip select.
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
This driver implements the ECC algorithm described in
the CPU data sheet and uses the OOB layout chosen in
already-released development systems (shipped with a custom-made
u-boot 1.3.1).
Signed-off-by: Alessandro Rubini <rubini@unipv.it>
Acked-by: Andrea Gallo <andrea.gallo@stnwireless.com>
The previous merge for cleaning up the I2C driver incorrectly reverted the
CFG_xxx rename for some of the I2C defines.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Heiko Schocher <hs@denx.de>
Fixing the get_timer function to return time in miliseconds instead of
ticks. Also fixed PXA boards to use the conventional value of 1000 for
CONFIG_SYS_HZ.
Signed-off-by: Micha Kalfon <smichak.uv@gmail.com>
- activate CS4 for accessing the FPGA
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flashes in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
- activate Rx buf len > 1 on SMC
- pram activated
- MTDPARTS_DEFAULT defined
- update the size of the flash in the DTS
before booting Linux
- MONITOR_LEN updated to 384k
- added CONFIG_HOSTNAME
- added CONFIG_ENV_BUFFER_PRINT
- Environment size reduced to 16k
Signed-off-by: Heiko Schocher <hs@denx.de>
This patch will create a configuration option for a minimum configuration for
the ns16550 serial driver at drivers/serial/ns16550.c and will apply this new
configuration option to the SIMPC8313.h config file in order to fix the NAND
bootstrap build error. This option will exclude all functions with exception of
NS16550_putc and NS16550_init. This will be used primarily to save space and
remove unused code from builds in which space is limited.
Signed-off-by: Ron Madrid <ron_madrid@sbcglobal.net>
This patch prepares the good old PMC405 board support for
upcoming PMC405V2 patches.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch fixes coding style for PMC405 board support.
Also some unneeded features/code is removed.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com>
Signed-off-by: Stefan Roese <sr@denx.de>
1. Changes to the default environment:
- "bootcmd" defined as "run flash_self"
- "saveenv" command removed from "update"
- "uboot" changed to "u-boot" (also in "load")
- "addmtd" variable defined (and added to all boot commands)
2. CONFIG_CMD_JFFS2 defined to enable "mtdparts" command
3. MTDIDS_DEFAULT and MTDPARTS_DEFAULT defined
4. CONFIG_SYS_CBSIZE changed from 256 to 512. That solves the problem
with truncated "bootargs" environment variable.
Signed-off-by: Ilya Yanok <yanok@emcraft.com>
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
This patch allows using of SATA devices connected
to the onboard PCI SIL1334 SATA controller.
Signed-off-by: Valeriy Glushkov <gvv@lstec.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The TQM8548_AG is a variant of the TQM8548 module with 1 GiB memory,
CAN and without PCI/PCI-X and RTC. U-Boot can be built for this module
with "$ make TQM8548_AG_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_BE is a variant of the TQM8548 module with NAND and CAN
interface. With NAND support, the image is significantly larger and
TEXT_BASE is adjusted accordingly. U-Boot can be built for this
module with "$ make TQM8548_BE_config".
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
The TQM8548_AG module does not have the standard PCI/PCI-X interface
connected but just the PCI Express interface . So far it was not
possible to disable it without disabling the complete PCI interface
(CONFIG_PCI) including PCI Express.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Update the 86xx reset sequence to try executing a board-specific reset
function. If the board-specific reset is not implemented or does not
succeed, then assert #HRESET_REQ. Using #HRESET_REQ is a more standard
reset procedure than the previous method and allows all board
peripherals to be reset if needed.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
When we introduced the 36-bit config of the MPC8572DS board we had the
wrong PCI MEM bus address map. Additionally, the change to the address
map exposes a small issue in our dummy read on the ULI bus. We need
to use the new mapping functions to handle that read properly in the
36-bit config.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Previously we only allowed power-of-two memory sizes and didnt
handle >2G of memory. Now we will map up to CONFIG_MAX_MEM_MAPPED
and should properly handle any size that we can make in the TLBs
we have available to us
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
With actual u-boot compiling the mgcoge port fails, because
since commit ba705b5b1a it is
necessary to define CONFIG_NET_MULTI.
Seems to me the mgcoge port is the only actual existing 8260
port who uses CONFIG_ETHER_ON_SCC, so no other 8260 port needed
to be fixed.
Signed-off-by: Heiko Schocher <hs@denx.de>
The criteria of the AMCC SDRAM Controller DDR autocalibration
U-Boot code is to pick the largest passing write/read/compare
window that also has the smallest SDRAM_RDCC.[RDSS] Read Sample
Cycle Select value.
On some Kilauea boards the DDR autocalibration algorithm can
find a large passing write/read/compare window with a small
SDRAM_RDCC.[RDSS] aggressive value of Read Sample Cycle Select
value "T1 Sample".
This SDRAM_RDCC.[RDSS] Read Sample Cycle Select value of
"T1 Sample" proves to be to aggressive when later on U-Boot
relocates into DDR memory and executes.
The memory traces on the Kilauea board are short so on some
Kilauea boards the SDRAM_RDCC.[RDSS] Read Sample Cycle Select
value of "T1 Sample" shows up as a potentially valid value for
the DDR autocalibratiion algorithm.
The fix is to define a weak default function which provides
the minimum SDRAM_RDCC.[RDSS] Read Sample Cycle Select value
to accept for DDR autocalibration. The default will be the
"T2 Sample" value. A board developer who has a well defined
board and chooses to be more aggressive can always provide
their own board specific string function with the more
aggressive "T1 Sample" value or stick with the default
minimum SDRAM_RDCC.[RDSS] value of "T2".
Also put in a autocalibration loop fix for case where current
write/read/compare passing window size is the same as a prior
window size, then in this case choose the write/read/compare
result that has the associated smallest RDCC T-Sample value.
Signed-off-by: Adam Graham <agraham@amcc.com>
Signed-off-by: Stefan Roese <sr@denx.de>
CONFIG_SDRAM_PPC4xx_IBM_DDR2 is not set when include/asm-ppc/config.h is
included. So for katmai, CONFIG_MAX_MEM_MAPPED will get set to 256MB.
It makes perfect sense to set CONFIG_MAX_MEM_MAPPED to 2GB for all PPC4xx
boards right now.
Signed-off-by: Stefan Roese <sr@denx.de>
At some point an intentional double space at the end of the sentence
got changed into a tab in the GPL header line:
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
This patch fixes the damage.
Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
Added new CONFIG options for the three type of MAC-PHY interconnect and
applied them all relevant board config files
Signed-off-by: Ben Warren <biggerbadderben@gmail.com>
