In tsec_init, the MAC address is retrieved from 2 different structures
depending on whether DM_ETH is enabled or not.
But since the field name is the same inside both structures, we can
conditionally define the structure of the correct type and simplify the
assignments.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This replaces debug() calls with printf() so that it is immediately
obvious from the console that something is wrong.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This is a cosmetic patch that reorders variable definitions in the
inverse order of their line length, where possible.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
By convention, the eTSEC MDIO controller nodes are defined in DT at
0x2d24000 and 0x2d50000, but actually U-Boot does not touch the
interrupt portion of the register map (MDIO_IEVENTM, MDIO_IMASKM,
MDIO_EMAPM).
That leaves only the MDIO bus registers (MDIO_MIIMCFG, MDIO_MIIMCOM,
MDIO_MIIMADD, MDIO_MIIMADD, MDIO_MIIMCON, MDIO_MIIMSTAT) which start at
the 0x520 offset.
So shift the DT-defined register map by the offset of MDIO_MIIMCFG when
mapping the MDIO bus registers.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The point of this patch is to eliminate the use of the locally-defined
"reg" variable (which interferes with next patch) and simplify the
fallback to the default CONFIG_SYS_TBIPA_VALUE in case "tbi-handle" is
missing.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Macb Ethernet controller requires a RX buffer of 128 bytes. It is
highly sub-optimal for Gigabit-capable GEM that is able to use
a bigger DMA buffer. Change this constant and associated macros
with data stored in the private structure.
RX DMA buffer size has to be multiple of 64 bytes as indicated in
DMA Configuration Register specification.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
DMA configuration was heavily dependent on the HW
defaults, add function to properly set the required
fields, including the new dma_burst_length.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
GEM support higher DMA burst writes/reads than the default (4).
add configuration structure with dma burst length so it could be
applied later to DMA configuration.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the sgmii phy interface,
available only to DM users, dictated by current driver
design.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
macb.h provides macros for reading/setting bitfields,
in macb registers and descriptors. use that instead
of redefining them in the source file.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
add support for clock rates higher than 2.4Mhz
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Few registers and bits were added by Cadence and
they were not updated in the headers.
Take the latest definitions as defined in Linux
header (5.1) that also includes some comments
about existing registers.
One register was improperly named (UR), fix that.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Anup Patel <anup.patel@wdc.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This driver is used for MDIO muxes driven over I2C. This is currently
used on Freescale LS1028A QDS board, on which the physical MDIO MUX is
controlled by an on-board FPGA which in turn is configured through I2C.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Using 'phy_connect' instead of 'phy_find_by_mask' and 'phy_connect_dev'
both deduplicates code and adds support for 'fixed-link'.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
SGMII 2500 as supported on NXP SoCs requires AN to be disabled, handle
this case in the enetc sgmii init code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ethernet interfaces using serial protocols go through the serdes block
integrated in the SoC. This is accessed over dedicated internal MDIOs
which are part of the Ethernet PCI functions. Set up serdes at _start,
along with other protocol specific port/MAC configuration.
MDIO code is shared with enetc_mdio, read/write functions are exported
from fsl_enetc_mdio for this reason.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for the MDIO interface currently integrated in LS1028A SoC.
This MDIO interface is shared by multiple ethernet interfaces and is
presented as a stand-alone PCI function on the SoC ECAM.
Ethernet has a functional dependency on MDIO, for simplicity there is a
single config option for both.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a driver for NXP ENETC ethernet controller currently integrated in
LS1028A. ENETC is a fairly straight-forward BD ring device and interfaces
are presented as PCI EPs on the SoC ECAM.
Signed-off-by: Catalin Horghidan <catalin.horghidan@nxp.com>
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The fec_mxc.c driver can be reused by i.MX28 when DM_ETH is enabled.
One only needs to add proper compatible and dependency on FEC_MXC in the
Kconfig.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The designware eth driver registers an mdio bus during probe, but if no
PHY is found, this bus is never removed although probe failes and the
driver is shown as not probed in the dm tree.
This later leads to errors when e.g. the mii or mdio commands try to
use available mdio buses because the mdio bus is still registered but
all corresponding data structures are invalid because probe failed.
Fix this by unregistering the mdio bus on probe failure (just as it is
unregistered in the .remove callback, too).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a test using a makeshift MDIO MUX. The test is based on the existing
MDIO test. It uses the last emulated PHY register to verify MUX selection.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This 2nd register is used by the follow-up MDIO MUX test.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds a class for MDIO MUXes, which control access to a series of
downstream child MDIOs.
MDIO MUX drivers are required to implement a select function used to switch
between child buses.
MUX children are registered as MDIO buses and they can be used just like
regular MDIOs.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code fails to probe some C45 PHYs that also respond to C22 reads.
This is the case for PHYs like Aquantia AQR112, Marvell 88X2242 (as
previously posted on the u-boot list).
If the PHY ID reads all 0s just ignore it and try the next devad.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
adds AQR112 and AQR412 to the list of supported PHYs using existing AQR
code.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Macb can be used with Xilinx PCS/PMA PHY in fpga which is a 1000-baseX
phy(lpa 0x41e0). This patch adds checks for LPA_1000XFULL and
LPA_1000XHALF bits.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If macb is gem and is gigabit capable, lpa value is not read from
the right register(MII_LPA) and is read from MII_STAT1000. This patch
fixes reading of the lpa value.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add new driver for the TI AM65x SoC Gigabit Ethernet Switch subsystem (CPSW
NUSS). It has two ports and provides Ethernet packet communication for the
device and can be configured as an Ethernet switch. CPSW NUSS features: the
Reduced Gigabit Media Independent Interface (RGMII), Reduced Media
Independent Interface (RMII), and the Management Data Input/Output (MDIO)
interface for physical layer device (PHY) management. The TI AM65x SoC has
integrated two-port Gigabit Ethernet Switch subsystem into device MCU
domain named MCU_CPSW0. One Ethernet port (port 1) with selectable RGMII
and RMII interfaces and an internal Communications Port Programming
Interface (CPPI) port (Host port 0).
Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and on RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use phys_addr_t for mdio_base address to avoid build
warnings on arm64 and dra7. Cast it to uintprt_t before
assigning to regs.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch is to use block layer to read from mmc in cortina
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Because all MSCC SoC use the same MDIO bus, put the implementation in
one common file(mscc_miim) and make all the other MSCC network drivers to
use these functions.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A very simple test for DM_MDIO, mimicks a register write/read through the
sandbox bus to a dummy PHY.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When serdes configuration was written in hardware there was a delay
of 100ms to be sure that configuration was written. But the delay is not
needed because already the function serdes_write it is checking that the
operation finished.
Therefore remove the mdelay. This improves the speed of configuring the
network driver.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The code block reading the DT property for the clock output control was
before the phy's DT node pointer was set, so it could never work. Move
it after the node pointer is set.
Also store the unsigned 32-bit property into an unsigned value, not a
signed value, as the former will cause a problem if value overflows.
For instance, if one were to add 0xffffffff as a code to mean the clock
output should be turned off.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When not using DM_ETH, these PHY settings are programmed with default
values hardcoded into the driver. When using DM_ETH, they should come
from the device tree. However, if the device tree does not have the
properties, the driver will silent use -1. Which is entirely out of
range, programs nonsense into the PHY's registers, and does not work.
Change this to use the same defaults as non-DM_ETH if the device tree is
lacking the properties.
As an alternative, the kernel driver for the phy will display an error
message and fail if the device tree is lacking.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Janine Hagemann <j.hagemann@phytec.de>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
We should not access reserved register on i.MX8, otherwise met SERROR
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Synopsys GMAC 4.20 is used. And Phy mode for eval and disco is RMII
with PHY Realtek RTL8211 (RGMII)
We also support some other PHY config on stm32mp157c
PHY_MODE (MII,GMII, RMII, RGMII) and in normal,
PHY wo crystal (25Mhz and 50Mhz), No 125Mhz from PHY config
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
At present the link speed change callback is a nop. According to
macb device tree bindings, an optional "tx_clk" is used to clock
the ethernet controller's TX_CLK under different link speed.
In 10/100 MII mode, transmit logic must be clocked from a free
running clock generated by the external PHY. In gigabit GMII mode,
the controller, not the external PHY, must generate the 125 MHz
transmit clock towards the PHY.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Tested-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This updates DM version macb_linkspd_cb() signature for future
expansion, eg: adding an implementation for link speed changes.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move the main symbol for Freescale Fman Ethernet controller option to
Kconfig. Also migrate the CONFIG_SYS_QE_FMAN_FW_IN_xxx macros and
rename the SPIFLASH one to follow the same format as all of the others.
To do this fully we need to migrate CONFIG_QC, do so.
Signed-off-by: Tom Rini <trini@konsulko.com>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
In mt7629-rfb.dts, the phy-handle is a reference to the node phy0, not the
node itself:
phy-handle = <&phy0>;
phy0: ethernet-phy@0 {
reg = <0>;
}
However the driver used ofnode_find_subnode("phy-handle") to read the node.
It will always fail.
This patch replaces ofnode_find_subnode with dev_read_phandle_with_args to
make sure the node can be read correctly.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This version of the RTL-8168 is present on some development boards and
is compatible with this driver. Add support for identifying this version
of the chip so that U-Boot won't complain about it being unknown.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement this callback that allows the MAC address to be set for the
Ethernet card. This is necessary in order for the device to be able to
receive packets for the MAC address that U-Boot advertises.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
There is a need to fill node before clk_output_sel is setup.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: <hannes.schmelzer@br-automation.com>
Commit d397f7c45b ("net: phy: micrel: Separate KSZ9000 drivers from
KSZ8000 drivers") separated the KSZ8xxx and KSZ90x1 drivers and warns
that you shouldn't select both of them due to a device ID clash between
the KSZ9021 and the KS8721, asserting that "it is highly unlikely for a
system to contain both a KSZ8000 and a KSZ9000 PHY". Unfortunately
boards like the SAMA5D3xEK do contain both types of PHY, but fortunately
the Linux Micrel PHY driver provides a solution by using different PHY
ID and mask values to distinguish these chips.
This commit contains the following changes:
- The PHY ID and mask values for the KSZ9021 and the KS8721 now match
those used by the Linux driver.
- The warnings about not enabling both drivers have been removed.
- The description for PHY_MICREL_KSZ8XXX has been corrected (these are
10/100 PHYs, not GbE PHYs).
- PHY_MICREL_KSZ9021 and PHY_MICREL_KSZ9031 no longer select PHY_GIGE
since this is selected by PHY_MICREL_KSZ90X1.
- All of the relevant defconfig files have been updated now that
PHY_MICREL_KSZ8XXX does not default to 'Y'.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
In some of the device trees that specify skew values for KSZ90x1 PHYs
the values are stored (incorrectly) in the MAC node, whereas in others
it is in an 'ethernet-phy' subnode. Previously the code would fail to
find and program these skew values, so this commit changes it to look
for an "ethernet-phy" subnode first, and revert to looking in the MAC
node if there isn't one.
The device trees affected (where the skew values are in a subnode) are
imx6qdl-icore-rqs.dtsi, r8a77970-eagle.dts, r8a77990-ebisu.dts,
r8a77995-draak.dts, salvator-common.dtsi, sama5d3xcm.dtsi,
sama5d3xcm_cmp.dtsi, socfpga_cyclone5_vining_fpga.dts,
socfpga_stratix10_socdk.dts and ulcb.dtsi. Before this change the skew
values in these device trees would be ignored.
The device trees where the skew values are in the MAC node are
socfpga_arria10_socdk.dtsi, socfpga_arria5_socdk.dts,
socfpga_cyclone5_de0_nano_soc.dts, socfpga_cyclone5_de10_nano.dts,
socfpga_cyclone5_de1_soc.dts, socfpga_cyclone5_is1.dts,
socfpga_cyclone5_socdk.dts, socfpga_cyclone5_sockit.dts. These should be
unaffected by this change.
The changes were tested on a sama5d3xcm.
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Commit ff7bd212cb ("net: phy: micrel: fix divisor value for KSZ9031
phy skew") fixed the skew value divisor for the KSZ9031, but left the
code using the same divisor for the KSZ9021, which is incorrect.
The preceding commit c16e69f702 ("net: phy: micrel: add documentation
for Micrel KSZ90x1 binding") added the DTS documentation for the
KSZ90x1, changing it from the equivalent file in the Linux kernel to
correctly state that for this part the skew value is set in 120ps steps,
whereas the Linux documentation and driver continue to this day to use
the incorrect value of 200 that came from the original KSZ9021 datasheet
before it was corrected in revision 1.2 (Feb 2014).
This commit sorts out the resulting confusion in a consistent way by
making the following changes:
- Update the documentation to be clear about what the skew values mean,
in the same was as for the KSZ9031.
- Update the Micrel PHY driver to select the appropriate divisor for
both parts.
- Adjust all the device trees that state skew values for KSZ9021 PHYs to
use values based on 120ps steps instead of 200ps steps. This will result
in the same values being programmed into the skew registers as the
equivalent device trees in the Linux kernel do, where it incorrectly
uses 200ps steps (since that's where all these device trees were copied
from).
Signed-off-by: James Byrne <james.byrne@origamienergy.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For AQR405 in register 4.c441 bit 15 was override with 0. This caused the
phy to not negotiate at 2.5GB rate with mac. To avoid
this override it needed first to know the previous value of reg 4.c441
and set only bit 3.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't ignore return value of phy_probe() call as
the probe may fail and it needs to be reported.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch relocates the pointers inside phy_drivers incase
of manual reloc. Without this reloc, these points to invalid
pre relocation address and hence causes exception or hang.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
if an error occurs in ldpaa_eth_init, need to free all resources
before returning the error.
Threfore, free net_dev before returning from ldpaa_eth_init.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add EPHY CLK and RESET support for sun8i_emac driver to
enable EPHY TX clock and EPHY reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When EEE is supported by the PHY and the driver allows it, libphy in the
kernel is configuring the PHY to stop receiving the xMII clock while it
is signaling LPI. While this (usually) works fine in the kernel this is
causing issues in U-Boot when rebooting from the linux kernel with this
bit set (without having the possibility to reset the PHY) where the PHY
suddenly stops working.
A new quirk is introduced to unconditionally reset this bit. If the
quirk is not enabled using the proper configuration symbol, the PHY state
is not changed.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now that generic helpers are available, use those instead of relying on
ti specific functions.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Two new helper functions (phy_read_mmd() and phy_write_mmd()) are added
to allow access to the MMD PHY registers.
The MMD PHY registers can be accessed by several means:
1. Using two new MMD access function hooks in the PHY driver. These
functions can be implemented when the PHY driver does not support the
standard IEEE Compatible clause 45 access mechanism described in clause
22 or if the PHY uses its own non-standard access mechanism.
2. Direct access for C45 PHYs and C22 PHYs when accessing the reachable
DEVADs.
3. The standard clause 45 access extensions to the MMD registers through
the indirection registers (clause 22) in all the other cases.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add ifdeffery to allow operation without the clock framework
enabled. This is required on RZ/A1, as it does not have clock
driver yet.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for RZ/A1 SoC specifics.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are no more boards using this CPU and there is no prospect
of any boards showing up soon, remove it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Chris Brandt <chris.brandt@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
-----BEGIN PGP SIGNATURE-----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=SZ/W
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-05-03' of git://git.denx.de/u-boot-mips
- mscc: small fixes, enhance network support for Serval, Luton and Ocelot
- mt7620: rename arch to more generic name mtmips
- mips: pass initrd addresses via DT as physical addresses
According to the R-Car Gen3 Hardware Manual Rev 1.50 of Nov 30, 2018, the
TX clock internal delay mode isn't supported on R-Car E3 (r8a77990) or D3
(r8a77995).
Avoid setting the APSR:TDM bit on these SoCs. Moreover, only set APSR:TDM
when the DT explicitly specifies RGMII ID or TXID mode instead of setting
it unconditionally when the PHY link speed is 1000 Mbit/s.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The boards with SoCs from the DaVinci DM* family used to come with
different PHYs that needed special support implemented in mach-davinci.
Since the support for these chips has long been removed, we can now
drop this unnused code from the emac driver.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Update Luton network driver to have support also for pcb90. The pcb90
has 24 ports from which 12 ports are connected to SerDes6G.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently mach-mt7620 contains only support for mt7628. To avoid confusion,
rename mach-mt7620 to mach-mtmips, which means MediaTek MIPS platforms.
MT7620 and MT7628 should be distinguished by SOC_MT7620 and SOC_MT7628
because they do not share the same lowlevel codes.
Dependencies of four drivers are changed to SOC_MT7628 as these drivers
are only used by MT7628.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Add network driver for Microsemi Ethernet switch.
It is present on Serval SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Since the introduction of the driver, some memory in IRAM is reserved for
the TX buffers.
However there are not used but instead of it, it is the buffer provided
by the net stack which is used. As stated in the comment of the driver,
not using the IRAM buffer could cause cache issue and lower the
throughput.
For the second argument it is less the case for transmitting buffers
because the throughput gain in IRAM is mitigated by the time to copy the
data from RAM to IRAM, but the first argument is still valid and indeed
this patch fixes issue seen with Ethernet on some boards
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
It adds the driver for HIGMACV300 Ethernet controller found on HiSilicon
SoCs like Hi3798CV200. It's based on a downstream U-Boot driver, but
quite a lot of code gets rewritten and cleaned up to adopt driver model
and PHY API.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When fixing sandbox test for regmap_read_poll_timeout(), the
sandbox_timer_add_offset was introduced but only defined in sandbox code
thus generating warnings when used out of sandbox :
include/regmap.h:289:2: note: in expansion of macro 'regmap_read_poll_timeout_test'
regmap_read_poll_timeout_test(map, addr, val, cond, sleep_us, \
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c:169:8: note: in expansion of macro 'regmap_read_poll_timeout'
ret = regmap_read_poll_timeout(spifc->regmap, REG_SLAVE, data,
^~~~~~~~~~~~~~~~~~~~~~~~
drivers/spi/meson_spifc.c: In function 'meson_spifc_txrx':
include/regmap.h:277:4: warning: implicit declaration of function 'sandbox_timer_add_offset' [-Wimplicit-function-declaration]
This fix adds a timer_test_add_offset() only defined in sandbox, and
renames the previous sandbox_timer_add_offset() to it.
Cc: Simon Glass <sjg@chromium.org>
Reported-by: Tom Rini <trini@konsulko.com>
Fixes: df9cf1cc08 ("test: dm: regmap: Fix the long test delay")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
Add CLK and RESET support for sun8i_emac driver to
enable TX clock and reset pins via CLK and RESET
framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Unlike other Allwinner SoC's R40 GMAC clock control register
is locate in CCU, but rest located via syscon itself. Since
the phandle property for current code look for 'syscon' and
it will grab the respective ccu or syscon base address based
on DT property defined in respective SoC dtsi.
So, use the existing 'syscon' code even for R40 for retrieving
GMAC clock via CCU and update the register directly in
sun8i_emac_set_syscon instead of writing it separately using
ccm base.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Lothar Felten <lothar.felten@gmail.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add CLk support for sunxi_emac to enable AHB_EMAC clock
via CLK framework.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The phydev supported features were reset in phy_set_supported() so,
move the setting of driver supported features after this so that it
wont lost in phy_set_supported().
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
-----BEGIN PGP SIGNATURE-----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=KLsH
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20190415' of git://git.denx.de/u-boot-imx
Move to DM
-----------
- DM support in sata
- Toradex Board to DM
- wandboard to DM
- tbs2910 to DM
- GE boards to DM
- VHybrid boards to DM
- DM_VIDEO for i.MX
The NXP's FEC driver can be reused on vf610 device (with DM).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Stefan Agner <stefan.agner@toradex.com>
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
-----BEGIN PGP SIGNATURE-----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=NrV8
-----END PGP SIGNATURE-----
Merge tag 'mips-pull-2019-04-12' of git://git.denx.de/u-boot-mips
- mt76xx: add USB support, small fixes
- ath79: small fixes, add support for QCA9563 SoC and AP152 reference board
- mscc: small fixes, add network support for JR2 and ServalT SoCs
- bmips: small fixes, enable more drivers for ARM specific BCM6858 and BCM63158 SoCs
- MIPS: fix redundant relocation of initrd images
Add network driver for Microsemi Ethernet switch.
It is present on ServalT SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add network driver for Microsemi Ethernet switch.
It is present on Jaguar2 SoCs.
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
S17 ethernet support is for QCA8337N, which used on
AP152 (QCA9563) board. It is a 7 ports GbE switch.
Signed-off-by: Rosy Song <rosysong@rosinson.com>
Changes for v2-v3:
- add more commit message for s17
Changes for v4-v5:
- coding style cleanup
The function mscc_miim_reset resets all the phys, but it is called for
each phy separetely. One consequence of this is that the boot time
is increased by 2 seconds.
The fix consists for calling the mscc_miim_reset function only once for
all phys.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The SPL image overflows when cpsw dt nodes are added and SPL_OF_CONTROL
is enabled. Use static platdata instead to save space.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
The ofdata_to_platdata function should not be called if OF_CONTROL is
not enabled because fdtdec_* calls will fail. Block the function with
OF_CONTROL
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ti_cm_get_macid() is used to get a syscon node from the dt, read the
efuse address and then assign the macid read from the address. Divide
these two steps into separate functions one of which can be called from
ofdata_to_platdata() while the other can be called from _probe(). This
ensures that platdata can be assigned statically in a board file when
OF_CONTROL is not enabled. Also add a macid_sel_compat in private data
to get information about the macid byte placement.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Convert cpsw_platform_data to a pointer in cpsw_priv. Allocate it
dynamically and assign it as a part of eth_pdata. This helps in
isolating platform data handling and implementing platdata for SPL
in a board file.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
cpsw_phy_sel() is a configuration step that should not be in
ofdata_to_platdata(). Add phy_sel_compat to the cpsw_platform_data
structure so that it is accessible in _probe. Then move the call of
cpsw_phy_sel() to _probe.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Enhance the netcp driver to support phys that can be configured
for internal delay (rgmii-id, rgmii-rxid, rgmii-txid)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reset and initialize the PHY once in the probe() function rather than
doing it over and over again is start() function. This requires us to
keep the clock enabled while the driver is in use. This significantly
reduces the time between transfers as the PHY doesn't have to restart
autonegotiation between transfers, which takes forever.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
I've noticed that the first ethernet packet after PHY link establishment
is not tranferred correctly most of the time on my AT91SAM9G25 board.
Here I usually see a timeout of a few seconds, which is quite
annoying.
Adding a small delay (10ms in this case) after the link establishment
helps to solve this problem. With this patch applied, this timeout
on the first packet is not seen any more.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Wenyou Yang <wenyou.yang@atmel.com>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As per Linux kernel DT binding doc:
- phy-reset-post-delay : Post reset delay in milliseconds. If present then
a delay of phy-reset-post-delay milliseconds will be observed after the
phy-reset-gpios has been toggled. Can be omitted thus no delay is
observed. Delay is in range of 1ms to 1000ms. Other delays are invalid.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@netmodule.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Negative phy-addresses can occour if the caller function was not able to
determine a valid phy address (from device-tree for example). In this
case we catch this here and search for ANY phy device on the given mdio-
bus.
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Lukasz Majewski <lukma@denx.de>
If node /board_info/ports does not exist in the DPC file,
function mc_fixup_dpc() will skip not only MAC address fixup,
but also the cache flush at the end. This may cause the other
fixup changes (e.g. ICID related ones) to be ignored by MC.
Fixes: 1161dbcc0a ("drivers: net: fsl-mc: Include MAC addr fixup to DPL")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
some dpmacs in armv8a based freescale layerscape SOCs can be
configured via both serdes(sgmii, xfi, xlaui etc) bits and via
EC*_PMUX(rgmii) bits in RCW.
e.g. dpmac 17 and 18 in LX2160A can be configured as SGMII from
serdes bits and as RGMII via EC1_PMUX/EC2_PMUX bits
Now if a dpmac is enabled by serdes bits then it takes precedence
over EC*_PMUX bits. i.e. in LX2160A if we select serdes protocol
that configures dpmac17 as SGMII and set the EC1_PMUX as RGMII,
then the dpmac is SGMII and not RGMII.
Therefore, in fsl_rgmii_init function of SOC, we will check if the
dpmac is enabled or not? if it is (fsl_serdes_init has already enabled
the dpmac), then don't enable it.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
The phy_connect_dev(...) function from phy.c does all the handling
(inclusive catching fixed-link).
So we drop here the single steps and call just phy_connect_dev(...).
Signed-off-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Fix MID bit field check to correctly identify all GEM hardwares.
The check is updated as per macb driver in Linux location:
<linux_sources>/drivers/net/ethernet/cadence/macb_main.c:259
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Don't fail in macb_enable_clk() if clk_enable() returns
-ENOSYS because we get -ENOSYS for fixed-rate clocks.
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Enable the socfpga specific designware ethernet driver by default for
socfpga by implying it when enabling CONFIG_ETH_DESIGNWARE for a
MACH_SOCFPGA config.
This is required to remove the hacky reset and phy mode handling in
arch/arm/mach-socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
This driver was written for Arria10, but it applies to Gen5, too.
The main difference is that Gen5 has 2 MACs (Arria10 has 3) and the
syscon bits are encoded in the same register, thus an offset is needed.
This offset is already read from the devicetree, but for Arria10 it is
always 0, which is probably why it has been ignored. By using this
offset when writing the phy mode into the syscon regiter, we can use
this driver to set the phy mode for both of the MACs on Gen5.
Since the PHY mode bits in sysmgr are the same even for Stratix10,
let's drop the detection of the sub-mach by checking compatible
version and just use the same code for all FPGAs.
To work correctly, this driver depends on SYSCON and REGMAP, so select
those via Kconfig when it is enabeld.
Tested on socfpga_socrates (where the 2nd MAC is connected, so a shift
offset is required).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
phy_reset should be called before autoneg is setup
The only boards using MV88E61XX_SWITCH are:
- alliedtelesis/SBx81LIFKW
- alliedtelesis/SBx81LIFXCAT
- gateworks/gw_ventana
Cc: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
When DM_REGULATOR is enabled, the driver attempts to call
regulator_autoset() which expects the regulators to be on at boot
and/or always on and fails if they are not true.
For a more generic approach, this patch just calls
regulator_set_enable() which shouldn't have such restrictions.
Fixes: ad8c43cbca ("net: dm: fec: Support the phy-supply
binding")
Signed-off-by: Adam Ford <aford173@gmail.com>
Tested-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This functions can be reused by other MSCC SoCs therefore,
make them more generic and move them in separate files.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Move file ocelot_switch to mscc_eswitch to prepare to add
new net drivers for other MSCC SoCs.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Currently if we have more than one phy on the MDIO bus, we do not have a
good mechanism for determining which should be used at runtime. Enable the
FEC driver to determine the address for the PHY from the device tree.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Print information about Aquantia system interface and firmware loaded
on the phy.
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If System Interface protocol is USXGMII then enable USXGMII autoneg
Signed-off-by: Valentin Catalin Neacsu <valentin-catalin.neacsu@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
No mainline board enables CONFIG_MCAST_TFTP and there have been
compilation issues with the code for some time. Additionally, it has a
potential buffer underrun issue (reported as a side note in
CVE-2018-18439).
Remove the multicast TFTP code but keep the driver API for the future
addition of IPv6.
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
ether_crc was added to the core net code in commit 53a5c424bf
("multicast tftp: RFC2090") so that other drivers could use it. However
the only current user of it is tsec.c so move it there.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
According to the datasheet to access the extended registers we have to:
1. Write Register 31 Data = 0x0XYZ (Page 0xXYZ)
2. Read/Write the target Register Data
3. Write Register 31 Data = 0x0000 or 0xa42 (switch back to IEEE
Standard Registers)
Hook the missing functions so that we can use the `mdio rx/wx` command to
easily access the extended registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch add GPIO configuration support in mvneta driver.
Driver will handle PHY reset. GPIO pins should be set in device tree.
Ported from mvpp2x
[https://patchwork.ozlabs.org/patch/799654/]
Initial discussion to port the changes into mvneta
[https://patchwork.ozlabs.org/patch/1005765/]
Signed-off-by: Aditya Prayoga <aditya@kobol.io>
Tested-by: Dennis Gilmore <dgilmore@redhat.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Some existing device trees don't specify a phy-mode so fallback to GMII
when a phy-mode is not provided.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
For KSZ9021, all skew register fields are 4-bit wide.
For KSZ9031, the clock skew register fields are 5-bit wide.
The common code in ksz90x1_of_config_group calculating the combined
register value checks if the requested value is above the maximum
and uses this maximum if so. The calculation of this maximum uses
the register width, but the check itself does not. It uses a hardcoded
value of 0xf, which is too low in case of the 5-bit clock (0x1f).
This detail was probably lost during driver unification.
Effect (only for KSZ9031 clock skews): For values greater 900 (== 0ps),
this silently results in 1860 (== +960ps) instead of the requested one.
Fix the check by using the bit width instead of hardcoded value(s).
Signed-off-by: Andreas Pretzsch <apr@cn-eng.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current code forces all ports on a given Ethernet device to use the same
mdio device. In practice different ports might be wired to separate mdio
devices. Move the mdio device from the container struct mvpp2 to the per
port struct mvpp2_port.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Current mdio base lookup code relies on a 'reg' property at the upper CP
node. There is no 'reg' property there in current DT files of Armada
CP110. Use ofnode_get_addr() instead since it provides proper DT address
translation.
Cc: Ken Ma <make@marvell.com>
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Short frames are padded to the minimum allowed size of 60 bytes.
However, the designware driver sends old data in these padding bytes.
It is common practice to zero out these padding bytes ro prevent
leaking memory contents to other hosts.
Fix the padding code to zero out the padded bytes at the end.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The designware driver has a bug in setting the tx length into the dma
descriptor: it always or's the length into the descriptor without
zeroing out the length mask before.
This results in occasional packets being transmitted with a length
greater than they should be (trailer). Due to the nature of Ethernet
allowing such a trailer, most packets seem to be parsed fine by remote
hosts, which is probably why this hasn't been noticed.
Fix this by correctly clearing the size mask before setting the new
length.
Tested on socfpga gen5.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The phy devices can be accessed via clause 22 or via clause 45.
This information can be deduced when we read phy id. if the phy id
is read without giving any MDIO Manageable Device Address (MMD), then
it conforms to clause 22. otherwise it conforms to clause 45.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch moves fixed-link functionality code to a separate
routine inorder to make it more modular and cleaner.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The cache was only flushed before *transmitting* packets, but not
when receiving them, leading to an issue where new packets were
handed to the receive handler with old contents in cache. This
only happens when a lot of packets are received without sending
packages every now and then. Also flushing the receive buffers
in the transmit function makes no sense and can be removed.
Signed-off-by: Stefan Theil <stefan.theil@mixed-mode.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch adds support for the Microsemi Ethernet switch present on
Ocelot SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
fsl-mc lazyapply command applies dpl from efi_exit_boot_services().
Status of fsl-mc node in working fdt is updated at this stage.
However, an efi application like grub may already have copied the fdt.
So the updates to fdt done at efi_exit_boot_services() may not be
visible to the OS. Fix it by updating fdt earlier if fsl-mc lazyapply
command is used.
Fixes: b7b8410a8f (ls2080: Exit dpaa only right before exiting U-Boot)
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlw+AlIACgkQfxc6PpAI
reYchAf+L/P5JsLoCKAY84v11eWQkCS44idAYStD8Q023dyuyNC/W6G3qEQVGkHu
SXBzNrZ5wSJanN5I3h3ktJ7yfMOYIvSO2qLHphxDstPaZbCY4Zac6NywHrHxQpA9
fbSilQRbcVWrPo5rsjjZhXmMdQRZVOmGD6CYZj1AihWAiHfYth7f6laNWNTWQA8C
z+aoiF70t/PbvwFbgdzzYOjoGdXI9XML0xTqdLWRlsBKjf3z54pCV6LmN2xrsrDZ
k7lr+x7ajJUFhivxzjowf4aOjhDB+/+I3sr+hJ5vkMM0Kqg14bbEU+xJRGpDc18K
QPvVHT5JGe/nq1cZXuCqzrYxTrrA7A==
=w9ln
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-15jan19' of git://git.denx.de/u-boot-dm
Fix recent changes to serial API for driver model
Buildman clang support and a few fixes
Small fixes to 'dm tree' and regmap test
Improve sandbox build compatibility
A few other minor fixes
At present this stores the error number in an unsigned int so an error is
never detected. Use the existing signed variable instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds ethernet support for Mediatek ARM-based SoCs, including
a minimum setup of the integrated switch.
Cc: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Mark Lee <Mark-MC.Lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Tested-By: "Frank Wunderlich" <frank-w@public-files.de>
When fixed-link phy is used subnode offset is used as phy address. This
number is bigger then space allocated for bus structure (allocated via
mdio_alloc).
bus->phymap[] array has PHY_MAX_ADDR size (32).
That's why writing bus->phymap[addr] where addr is < 0 or > PHY_MAX_ADDR
is causing write to memory which can caused full U-Boot crash.
The patch is checking if address is in correct range.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add support for lx2160a SoC
-----BEGIN PGP SIGNATURE-----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=aT7d
-----END PGP SIGNATURE-----
Merge tag 'fsl-qoriq-for-v2019.01-rc2' of git://git.denx.de/u-boot-fsl-qoriq
Add TFA boot flow for some Layerscape platforms
Add support for lx2160a SoC
[trini: Add a bunch of missing MAINTAINERS entries]
Signed-off-by: Tom Rini <trini@konsulko.com>
This merges the CRC16-CCITT headers into u-boot/crc.h to prepare for
rolling CRC16 into the hash infrastructure. Given that CRC8, CRC32
and CRC32-C already have their prototypes in a single header file, it
seems a good idea to also include CRC16-CCITT in the same.
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Adds TFABOOT support and allows to pick FMAN firmware
on basis of boot source.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
[YS: fix checkpatch issues]
Reviewed-by: York Sun <york.sun@nxp.com>
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlwIe0gRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreY02wgAjK9U1ADmoNi4xWgtq83EerxOGTq68BRD
CfnUDgI+FQHNv/LxdZ8lZ2lgGG1xXZ8mdeHWghllHoLEnwMQ3LxfDRnpkyC6VBE9
LvZF4F7BhTnGsKImlloQ5oMhKI4sDKjqRkRL3D633x5dq9Z571obAyGwLMo67vv6
U8iv1mRMr6au46pLvH25DF6h5LuM7TBSJVDlzmFmmD++r/YDroTJfo07qdo8sNqS
0hDPjgp3uqf1mX2cbNHk56a3DmO9fL6Gcvdv0LHGQvRyfQ36TY+cEcDU2y2p+tl+
t1LFamfZvalix9AyJegr3qGMOb9B20ar89EItXzH9J+ahnlZmEat+w==
=VAMW
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-5dec18' of git://git.denx.de/u-boot-dm
Minor sandbox enhancements / fixes
tpm improvements to clear up v1/v2 support
buildman toolchain fixes
New serial options to set/get config
We cannot be sure that the interface name takes up the full length of the
space available to it. Use strcpy() instead of memcpy() in this case. This
corrects a valgrind warning.
Signed-off-by: Simon Glass <sjg@chromium.org>
This patch throws an error if 64-bit support is expected
but DMA hardware is not capable of 64-bit support. It also
prints a debug message if DMA is capable of 64-bit but not
using it.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
This patch adds 64-bit addressing support for zynq gem.
This means it can perform send and receive operations on
64-bit address buffers.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
Some boards have the EMAC TX/RX lanes wired with a different length with
the clock lane, which can be workarounded by setting a TX/RX delay in
the EMAC.
This kind of delays are already defined in the newest device tree
binding of dwmac-sun8i, which has already entered linux-next.
Add support for setting these delays.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Update TI Keystone 2 driver to re-use common mdio lib.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Update TI CPSW driver to re-use common mdio lib
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
All existing TI SoCs network HW have similar MDIO implementation, so
introduce common mdio support library which can be reused by TI networking
drivers.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update to use SPDX license identifier.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Networking support for all TI K2 boards converted to use DM model and
CONFIG_DM_ETH enabled in all corresponding defconfig files, hence drop
unused non DM K2 networking code.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Add drivers/net/ti/ folder and move all TI's code in this folder for better
maintenance.
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
The VSC8574 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.
The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the config is common between the VSC8584 and the VSC8574, so to
prepare for the upcoming support of VSC8574, use the phy_device.priv
pointer that will keep the function that holds code that is PHY-specific
and that should be called during config function.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The VSC8584 PHY is a 4-port PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.
This adds support for 10/100/1000BASE-T and SGMII/QSGMII link with the
MAC.
The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.
The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.
The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Faraday ftgmac100 MAC controllers as found on the Aspeed SoCs have
some slight differences in the HW interface (End-Of-Rx/Tx-Ring bits).
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use simple arrays under the device priv structure to hold the RX and
TX descriptors and handle memory coherency by invalidating or flushing
the d-cache when required.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Implement the MDIO bus read/write functions using the readl_poll_timeout()
routine, initialize the bus and scan for the PHY. RGMII and RMII mode
are supported.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The driver is based on the previous one and the code is only adapted
to fit the driver model. The support for the Faraday ftgmac100
controller is the same with MAC and MDIO bus support for RGMII/RMII
modes.
Configuration is updated to enable compile again. At this stage, the
driver compiles but is not yet functional.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds ethernet support for the MIPS based Mediatek MT76xx SoCs
(e.g. MT7628 and MT7688), including a minimum setup of the integrated
switch. This driver is loosly based on the driver version included in
this MediaTek github repository:
https://github.com/MediaTek-Labs/linkit-smart-uboot.git
Tested on the MT7688 LinkIt smart-gateway and on the
Gardena-smart-gateway.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Frank Wunderlich <frankwu@gmx.de>
Cc: Weijie Gao <hackpascal@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Per T1040RM (Rev. 1, 08/2015), there are 2 issues with the RCW EC2
settings.
- The value of FSL_CORENET_RCWSR13_EC2_FM1_GPIO is wrong and should
be 0x04000000 (value of 1 in RCW bit [420:421])
- Value of 2/3 are reserved in RCW bit [420:421], hence there is no
macro FSL_CORENET_RCWSR13_EC2_FM1_DTSEC5_MII.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Poonam Aggrwal <poonam.aggrwal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Complete in the drivers directory the work started with
commit 83d290c56f ("SPDX: Convert all of our single
license tags to Linux Kernel style").
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add compatible property and enable the FEC ipg clock when probing
on i.MX8X. Add specific function for reading FEC clock rate via
clock driver when configuring MII speed register. Allow FEC_MXC
selection for i.MX8.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The default Linux PHY reset delay is 10ms. This is also the requirement
for Marvell 88E151x PHYs, which are likely to be used with this Ethernet
MAC.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The dm_gpio_set_value() call sets the logical level of the GPIO signal.
That is, it takes the GPIO_ACTIVE_{LOW,HIGH} property into account. The
driver needs to assert the reset, and then deassert it. Not the other
way around.
Cc: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The DT property "phy-mode" already provides the transceiver type.
Use it so that we do not have to also set CONFIG_FEC_XCV_TYPE
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Configure the phy regulator if defined by the "phy-supply" DT phandle.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says:
- phy-reset-duration : Reset duration in milliseconds. Should present
only if property "phy-reset-gpios" is available. Missing the property
will have the duration be 1 millisecond. Numbers greater than 1000 are
invalid and 1 millisecond will be used instead.
However the current code:
- clamps values greater than 1000ms to 1000ms rather than 1.
- does not initialize the delay if the property does not exist
(else clause mismatch)
- returns an error if phy-reset-gpios is not defined
Fix all this and simplify by using dev_read_u32_default()
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The DT binding says that phy-reset-duration is in ms, but the driver
currently uses udelay().
Switch to mdelay() to fix this.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
If the phy reports a valid firmware version and doesn't indicate
a fault, skip loading the firmware. This allows the same image
to be used on boards that have firmware storage and those that do not.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Aquantia phys have firmware that can be loaded automatically
from storage directly attached to the phy or via MDIO commands.
Add support for loading firmware from either a file or a
raw location on an MMC device.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The aquantia driver requires both CONFIG_PHY_GIGE and CONFIG_PHYLIB_10G.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Xilinx SoC Versal is using fixed clock where setting rate is not supported.
That's why workaround the driver till real clock driver is supported.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
