- Add DM based generic watchdog start and reset implementation
and remove all ad-hoc implementations (Stefan)
- Move mv_sdhci to DM (Pierre)
- Misc turris_omnia updates (Pierre)
- Change openrd targets to correctly build again (size changes
and fixes to the dts targets) and bring it back into Travis
builds (Stefan)
- Add Kirkwood db-88f6281-bp board (Chris)
With the latest size increase of the openrd boards, they all compile
clean again. Let's mark them as maintained again and add the Travis
job.
Please note that I can only compile-test these targets as I don't
have access to one of those boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Albert ARIBAUD <albert-u-boot@aribaud.net>
Cc: Vagrant Cascadian <vagrant@debian.org>
Cc: Chris Packham <judge.packham@gmail.com>
Cc: Tom Rini <trini@konsulko.com>
With the new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
The watchdog servicing is enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
With the generic watchdog driver now implemented, this patch removes
some legacy stuff from the MPC8xx watchdog driver and its Kconfig
integration. CONFIG_MPC8xx_WATCHDOG is completely removed and
hw_watchdog_reset() is made static, as the watchdog will now get
serviced via the DM infrastructure if enabled via CONFIG_WATCHDOG.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Now that we have a generic DT property "timeout-sec" handling, the
driver specific implementation can be dropped.
This patch also changes the timeout restriction to the min and max
values (clipping). Before this patch, the value provided via
"timeout-sec" was used if the parameter was too high or low. Now
the driver specific min and max values are used instead.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
This patch tries to implement a generic watchdog_reset() function that
can be used by all boards that want to service the watchdog device in
U-Boot. This watchdog servicing is enabled via CONFIG_WATCHDOG.
Without this approach, new boards or platforms needed to implement a
board specific version of this functionality, mostly copy'ing the same
code over and over again into their board or platforms code base.
With this new generic function, the scattered other functions are now
removed to be replaced by the generic one. The new version also enables
the configuration of the watchdog timeout via the DT "timeout-sec"
property (if enabled via CONFIG_OF_CONTROL).
This patch also adds a new flag to the GD flags, to flag that the
watchdog is ready to use and adds the pointer to the watchdog device
to the GD. This enables us to remove the global "watchdog_dev"
variable, which was prone to cause problems because of its potentially
very early use in watchdog_reset(), even before the BSS is cleared.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: "Marek Behún" <marek.behun@nic.cz>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Cc: Maxim Sloyko <maxims@google.com>
Cc: Erik van Luijk <evanluijk@interact.nl>
Cc: Ryder Lee <ryder.lee@mediatek.com>
Cc: Weijie Gao <weijie.gao@mediatek.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: "Álvaro Fernández Rojas" <noltari@gmail.com>
Cc: Philippe Reynes <philippe.reynes@softathome.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com> (on zcu100)
With the latest changes to the drivers (SPI_FLASH_SPANSION etc), Travis
reports that the SPL image is too big. Let's use the thumb instructions
in SPL to save some space and make the image fit again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Switch to the driver model for USB on the db-88f6281-bp board.
CONFIG_BLK can't be enabled yet because mvebu_mmc.c needs converting.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This is Marvell's Kirkwood development board. It has the following
features
- 512M DDR2
- 2 PCI connectors
- 1 x1 PCI-e interface
- 1 Gigabit Ethernet Port
- 2 SATA Ports
- USB 2.0 Interface
- SDIO
- 128M NAND Flash
- 16M SPI Flash
It can be strapped to boot from SPI or NAND so there are two defconfigs
(one per boot media).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The boot commands have changed in the environment. Add a note about the
incompatible change and how resolve the issue in the board's README.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We have run now multiple times into size issues with the openrd
board port. To finally fix this, this patch now moves the U-Boot size
from 0x6.0000 to 0x8.0000, giving enough space for the next time.
This also changes the environment location and potentially the
MTD partitioning, but I see no better fix for now. Especially since
this board does not have an active maintainer.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Remove the superfluous CONFIG_ENV_ADDR definition. Its not needed
as CONFIG_ENV_OFFSET is also set to the same value.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The following Kirkwood dtb build targets are currently missing:
kirkwood-openrd-base.dtb
kirkwood-openrd-client.dtb
kirkwood-openrd-ultimate.dtb
This patch adds them to the Makefile to fix the build error.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable DM_MMC for compliance with the driver model migration.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
The new DM implementation currently does not support the Sheeva
88SV331xV5 specific quirk present in the legacy implementation. The
legacy code is thus kept for this SoC and others not yet migrated to
DM_MMC.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefan Roese <sr@denx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit c4bd12a7da ("i2c: mux: Generate longer i2c mux name") changed
the naming scheme of i2c devices within a mux. This broke references to
i2c@0 in the Turris Omnia board initialization code.
Signed-off-by: Pierre Bourdon <delroth@gmail.com>
Cc: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
A mailbox command contains 1-u32 header + arguments. The "len" variable
only contains the length of the arguments, but not the 1-u32 header.
Include the length of header when checking the ring buffer space to
prevent off-by-one error.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Signed-off-by: Chee Hong Ang <chee.hong.ang@intel.com>
Remove outdated defines (not used any more, outdated due to DM
conversion) from various socfpga files in include/config.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Series-version: 3
Series-changes: 2
- added (this) patch with further cleanups to the socfpga board config
files
socfpga_common.h defines CONFIG_SYS_BOOTMAPSZ to 64 MiB.
Since having this define overrides the 'bootm_size' env variable for
the whole socfpga platform, let's remove this define from socfpga_common.h
and instead rely on the 'bootm_size' env variable (which is initialized
to 160 MiB in the same file's default env). This gives users the
chance to override it in their own environment.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
Series-to: Marek Vasut <marex@denx.de>
Series-to: u-boot@lists.denx.de
Cover-letter:
arm: socfpga: clean up socfpga_common.h
This series cleans up the include/configs/socfpga_common.h file a bit.
It removes some defines that are used nowhere and cleans up some
leftovers after various subsystems have been converted to use DM.
END
Remove outdated macros and comments (not used any more, outdated due to
DM conversion) from socfpga_common.h.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 3
- changed commit message: s/defines/macros and comments/
Series-changes: 2
- remove even more outdated things
All socfpga boards except for vining_fpga use DM_I2C. Enable
DM_I2C for this board and set the EEPROM defines via Kconfig
(enabling CONFIG_I2C_EEPROM from MISC).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Series-changes: 2
- added (this) patch to move socfpga_vining to DM_I2C
By enabling debug prints in malloc_simple, we can see that SPL for socfpga
gen5 does by far not need the 8 KiB malloc pool currently allocated for
SPL in pre-reloc phase.
On socfpga_socrates, 1304 bytes are currently used (and this increases by
~200 bytes only for the sdram/reset fixes in socfpga-next).
To prevent wasting precious SRAM space, let's reduce the initial heap used
for SPL to 2 KiB. This is still some hundred bytes more than currently
used. Also, the gen5 SPL enables stack and heap in DDR memory pretty
early. Only the initial uclass/dm parsing, serial console and DDR
initialization is done in the initial heap, so these 2 KiB should be
enough for all boards.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This commit moves common config options used in all socfpga boards
to select/imply in Kconfig. This both cleans up the defconfig files
as well as makes future changes easier.
Options implied/defaulted for all sub-arches:
- SPL, SPL_DM, USE_TINY_PRINTF, NR_DRAM_BANKS
Options implied/defaulted for implied for A10 & gen5:
- FPGA_SOCFPGA, SYS_MALLOC_F_LEN, SYS_TEXT_BASE
Options implied/defaulted for gen5:
- SPL_STACK_R, SPL_SYS_MALLOC_SIMPLE, SPL_STACK_R_ADDR
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
If SPL post-reloc stage puts the stack into DDR, U-Boot should be able to
do that, too.
The reason to do so is that this way, U-Boot initial stack can be larger
than SPL initial stack. In situations where we want to save the SPL
in SRAM for next boot without reloading, this prevents overwriting the
SPL DTB in SRAM if U-Boot stack usage gets too high.
To achieve this, the malloc definition for a10 is moved up and sligthly
changed to ensure CONFIG_SYS_INIT_RAM_SIZE is the remaining available size.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
The comment about SPL memory layout for socfpga gen5 is outdated: the
initial malloc memory is now at the end of the SRAM, gd is below it
(see board_init_f_alloc_reserve).
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Marek Vasut <marex@denx.de>
This enables DM_RTC and RTC_M41T62 to enable support for the rtc on the
socrates board.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This patch makes the on-board RTC work on the socfpga_socrates board.
This rtc is present on the board, but it does not work (fails with a
timeout).
This patch adds a weak pull-up on the I2C0-SCL pin connected to the m41t82
RTC on this board. While the SDA line has a pull-up on the pcb, the pull-up
on the SCL line seems to be missing. To work around this, enable the
weak-pull-up feature on this pin.
After applying this patch, the rtc timeout is gone and the 'date' command
can access the rtc chip.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This adds a compatible string for m41t82. This ensures that this driver
can be used for m41t82 in DM mode, too (asit was usable for this model in
non-DM mode before).
In addition, the HT bit has to be reset during probe, since the m41t82
chip sets it when entering battery standby mode.
This patch ensures this driver works on socfpga_socrates.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Using this driver on socfpga gen5 with DM_I2C enabled leads to a data abort
as the 'i2c' reset property cannot be found (the gen5 dtsi does not provide
reset-names).
The actual bug was to check 'if (&priv->reset_ctl)', which is never false.
While at it, convert the driver to use 'reset_get_bulk' instead of looking
at a specific named reset and also make it release the reset on driver
remove before starting the OS.
Fixes: 622597dee4 ("i2c: designware: add reset ctrl to driver")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This reverts commit 65a97e7fcf.
The 'eeprom' command has been converted to work with DM_I2C in a patch
submitted around the same time as this commit:
commit 0c07a9b407 ("eeprom: Add device model based I2C support to eeprom command")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The current device model enabled eeprom code only works if
CONFIG_SYS_I2C_EEPROM_BUS is set.
This patch makes it work without that define so that the bus
number passed to 'eeprom_init' is used.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
-----BEGIN PGP SIGNATURE-----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=caQ+
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
This updates MAINTAINERS and git-mailrc to add me as a
co-custodian for socfpga.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
- Add and enable brcmnand driver on a number of relevant platforms.
Also add and enable LED drivers on more bcm platforms.
- Various ARMv8 fixes/improvements, including extending PSCI
functionality.
- fs_loader improvments
- Various FIT/SPL improvements
- PCI bugfixes
- Poplar platform ethernet support
- MediaTek MMC improvements
- Android boot improvements
According to Android image format [1], kernel image resides at 1 page
offset from the boot image address. Grab the magic number from there
and allow U-Boot to handle LZ4-compressed KNL binaries instead of
hardcoding compression type to IH_COMP_NONE. Other compression types,
if needed, can be added later.
Tested on H3ULCB-KF using the image detailed in [2].
[1] Excerpt from include/android_image.h
+-----------------+
| boot header | 1 page
+-----------------+
| kernel | n pages
+-----------------+
| ramdisk | m pages
+-----------------+
| second stage | o pages
+-----------------+
[2] => iminfo 4c000000
## Checking Image at 4c000000 ...
Android image found
kernel size: 85b9d1
kernel address: 48080000
ramdisk size: 54ddbc
ramdisk addrress: 4a180000
second size: 0
second address: 48000800
tags address: 48000100
page size: 800
os_version: 1200012a (ver: 0.9.0, level: 2018.10)
name:
cmdline: buildvariant=userdebug
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
If CONFIG_UNIT_TEST is enabled we should enable the individual tests by
default to ensure good test coverage.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
PCI_MSI_FLAGS_MASKBIT was missing from include file,
add it.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_setprop_u32() function does everything that we need, so we
really only use the function as a convenience wrapper, in which case it
can simply be a static inline function.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Testing has shown that the current DM implementation of a platform /
board specific translation offset, as its needed for the SPL on MVEBU
platforms is buggy. The translation offset is confingured too late,
after the driver bind functions are run. This may result in incorrect
address translations. With the current implementation its not possible
to configure the offset earlier, as the DM code has not run at all.
This patch now removed the set_/get_translation_offset() calls and
moves the translation offset into the GD variable translation_offset.
This variable will get used when CONFIG_TRANSLATION_OFFSET is enabled.
This option is enabled only for MVEBU on ARM32 platforms, where its
currenty needed and configured in the SPL.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pierre Bourdon <delroth@gmail.com>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Tested-by: Pierre Bourdon <delroth@gmail.com>
Tested-by: Baruch Siach <baruch@tkos.co.il>
Boards such as qemu-riscv, which receive their device tree at runtime,
for example from QEMU or firmware, are unable to add the appropriate
device tree properties to make devices available pre relocation.
Instead, they must rely on the DM_FLAG_PRE_RELOC flag to be set for the
required drivers.
Add the DM_FLAG_PRE_RELOC flag to the simple-bus driver to make devices
under it with drivers that have set the flag as well available pre
relocation for these boards.
Signed-off-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Enable this by default so that tracing can be inspected if enabled. This
cannot rely on the 'imply' in lib/Kconfig since this method of enabling
tracing relates on an environment variable (FTRACE) and does not use
Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_TRACE_BUFFER_SIZE
CONFIG_TRACE_EARLY_SIZE
CONFIG_TRACE_EARLY
CONFIG_TRACE_EARLY_ADDR
Signed-off-by: Simon Glass <sjg@chromium.org>
At present many functions in this file return -1. Update them to return a
valid error code. Also tidy up the 'return' statements at the same time,
since these should have a blank line before them.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function may be called from tracing code, since that code needs to
read the timer and this often requires calling do_div(), which calls
__div64_32(). If this function is instrumented it causes an infinite loop,
since emitting a trace record requests the time, which in turn emits a
trace record, etc.
Update the prototype to prevent instrumentation code being added.
Signed-off-by: Simon Glass <sjg@chromium.org>